ZnSe薄膜的激子光谱

采用分子束外延(MBE)技术,在GaAs(100)衬底上生长了厚度从O.045到1.4μm的ZnSe薄膜.X射线衍射谱证实,随着薄膜厚度的增加,应变逐步弛豫.测量了低温下样品的反射谱和光致发光谱,观察到轻重空穴的能级在不同应变下的分裂、移动和反转,以及激子极化激元(Polariton)对反射谱的影响.也观察到束缚激子发光随着薄膜厚度的变化规律:束缚在中性受主杂质上的束缚激子发光(I1峰)随着薄膜厚度的增加逐渐变弱直至消失,而束缚在中性施主杂质上的束缚激子发光(I2峰)则随着厚度增加逐渐增强.     

900℃空气退火对L-MBE生长的ZnO薄膜发光特性的影响

采用激光分子束外延法在蓝宝石衬底(0001)上生长了高度c轴择优取向的高质量ZnO薄膜,在空气中对生长的薄膜进行900℃退火处理,并对退火前后样品的结晶质量、发光特性采用X射线衍射(XRD)、变温光致发光(PL)研究.退火处理后的ZnO薄膜(0002)面XRDθ-2θ扫描曲线强度明显增强.在光致发光实验中,观测到薄膜分别在3.352,3.309和3.237eV附近有3个明显的近紫外发光峰,分别对应自由激子发射、中性施主或受主束缚激子I9及其声子伴线1Lo.随着温度升高,峰位逐渐向长波方向移动(即所谓"红移"),半高宽(FWHM)逐渐展宽;在发光谱中,来自于晶体缺陷的深能级(DL)区发光强度极小.     

900℃空气退火对L-MBE生长的ZnO薄膜发光特性的影响

采用激光分子束外延法在蓝宝石衬底(0001)上生长了高度c轴择优取向的高质量ZnO薄膜,在空气中对生长的薄膜进行900℃退火处理,并对退火前后样品的结晶质量、发光特性采用X射线衍射(XRD)、变温光致发光(PL)研究.退火处理后的ZnO薄膜(0002)面XRDθ-2θ扫描曲线强度明显增强.在光致发光实验中,观测到薄膜分别在3.352,3.309和3.237eV附近有3个明显的近紫外发光峰,分别对应自由激子发射、中性施主或受主束缚激子I9及其声子伴线1Lo.随着温度升高,峰位逐渐向长波方向移动(即所谓"红移"),半高宽(FWHM)逐渐展宽;在发光谱中,来自于晶体缺陷的深能级(DL)区发光强度极小.     

Mg_xZn_(1-x)O单晶薄膜和MgZnO/ZnO异质结构的光学性质

报道了利用等离子辅助分子束外延技术,在蓝宝石c平面上外延生长的Mgx Zn1 - x O单晶薄膜以及Mg Zn O/Zn O异质结构的光学性质.室温下随着Mg浓度增加,合金薄膜样品的发光峰与吸收边均向高能侧移动.研究了样品紫外发光的起因,将Mgx Zn1 - x O合金薄膜的发光归结为束缚激子的复合.在Mg0 .0 8Zn0 .92 O/ Zn O样品中,观察到了分别来自于Zn O层和Mg Zn O盖层的发光和吸收,并将其归因于来自Zn O层的自由激子和Mg Zn O盖层的束缚激子发射     

纳米ZnO光学性质研究进展

介绍了纳米ZnO常见发光谱的发光机制。在室温光致发光谱(PL)中,一般在380 nm处出现紫外发光,也有报道在357和377 nm处的紫外发光,列举了几种不同的发光解释。对于深能级发光,一般在400～550 nm出现连续的发光带,也有观察到深能级的声子伴线和声子复制现象。在低温光致发光谱的紫外发射中,一般观察到由自由激子发射(FX)、中性施主束缚激子发射(D0X)、施主-受主对跃迁峰(DAP)、中性施主束缚激子对应的双电子卫星峰(TES)以及声子伴线。综述了纳米ZnO的喇曼光谱、透射光谱、电致发光谱(EL)的特征,最后展望了纳米ZnO的光学性能研究前景。     

MgxZn1-xO单晶薄膜和MgZnO/ZnO异质结构的光学性质

报道了利用等离子辅助分子束外延技术,在蓝宝石c平面上外延生长的MgxZn1-xO单晶薄膜以及MgZnO/ZnO异质结构的光学性质.室温下随着Mg浓度增加,合金薄膜样品的发光峰与吸收边均向高能侧移动.研究了样品紫外发光的起因,将MgxZn1-xO合金薄膜的发光归结为束缚激子的复合.在Mg0.08Zn0.92O/ZnO样品中,观察到了分别来自于ZnO层和MgZnO盖层的发光和吸收,并将其归因于来自ZnO层的自由激子和MgZnO盖层的束缚激子发射.     

表面覆盖退火对ZnO薄膜光学性质的影响

研究了暴露在空气中退火和表面覆盖蓝宝石基板退火对MOCVD生长的ZnO薄膜光学性质的影响.研究发现,暴露在空气中退火虽可以去除薄膜中的氢杂质,并在低温光致发光(PL)谱中观察到与氢相关的束缚激子峰消失,但是退火后样品室温PL谱中可观察到很强的可见光发射,表明样品中引入了大量的深能级,样品的自由激子发光没有增强.而表面覆盖蓝宝石基板退火的样品,有效去除了氢杂质,但没有观察到可见光发射,说明表面覆盖蓝宝石基板退火可以有效地保护ZnO表面不分解,不生成深能级中心.由于激子束缚中心的减少,表面覆盖退火样品的自由激子发射大大增强.     

表面覆盖退火对ZnO薄膜光学性质的影响

研究了暴露在空气中退火和表面覆盖蓝宝石基板退火对MOCVD生长的ZnO薄膜光学性质的影响.研究发现,暴露在空气中退火虽可以去除薄膜中的氢杂质,并在低温光致发光(PL)谱中观察到与氢相关的束缚激子峰消失,但是退火后样品室温PL谱中可观察到很强的可见光发射,表明样品中引入了大量的深能级,样品的自由激子发光没有增强.而表面覆盖蓝宝石基板退火的样品,有效去除了氢杂质,但没有观察到可见光发射,说明表面覆盖蓝宝石基板退火可以有效地保护ZnO表面不分解,不生成深能级中心.由于激子束缚中心的减少,表面覆盖退火样品的自由激子发射大大增强.     

Effect of Surface-Covered Annealing on the Optical Properties of ZnO Films Grown by MOCVD

研究了暴露在空气中退火和表面覆盖蓝宝石基板退火对MOCVD生长的ZnO薄膜光学性质的影响. 研究发现，暴露在空气中退火虽可以去除薄膜中的氢杂质，并在低温光致发光(PL)谱中观察到与氢相关的束缚激子峰消失，但是退火后样品室温PL谱中可观察到很强的可见光发射，表明样品中引入了大量的深能级，样品的自由激子发光没有增强. 而表面覆盖蓝宝石基板退火的样品，有效去除了氢杂质，但没有观察到可见光发射，说明表面覆盖蓝宝石基板退火可以有效地保护ZnO表面不分解，不生成深能级中心. 由于激子束缚中心的减少，表面覆盖退火样品的自由激子发射大大增强.     

ZnS_(1-x)Te_x混晶的压力光谱

研究了 Zn S1 - x Tex(0 .0 2≤ x≤ 0 .3)混晶的静压光致发光谱 .每块样品都观察到一个峰值比相应混晶带隙低很多的发光峰 ,来源于束缚在 Ten(n≥ 2 )等电子陷阱上的激子复合发光 ,且随压力 (0～ 7.0 GPa)而蓝移 .发光峰的压力系数比相应混晶带边的都要小 ,随着 Te组分的增加而减小 ,与混晶带隙压力系数的差别也越来越大 .由于压力下与发光峰对应的吸收能量逐渐接近并超过激发光的能量 ,与发光峰有关的吸收效率降低 ,发光峰积分强度随着压力增加而减小 .据此估算了 Ten 等电子中心的 Stokes位移 .发现 Stokes位移随着 Te组分的增加而减小     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.