α/β复合成核剂对等规聚丙烯结晶形态的影响及非等温结晶动力学

采用偏光显微镜(POM)及示差扫描量热(DSC)法考察了3种α/β复合成核剂NA40/NABW、NA40/HHPA-Ba、NA40/PA-03对成核等规聚丙烯(iPP)的结晶形态及非等温结晶动力学的影响。对成核iPP结晶形态的研究结果表明：α/β复合成核剂的加入能够减小iPP的球晶尺寸。影响α/β复合成核剂成核iPP结晶形态的主要因素是ΔT_Cp（ΔT_Cp为成核iPP结晶峰值温度与iPP结晶峰值温度的差值）,即复合体系中ΔT_Cp较大的成核剂在iPP结晶过程中起主导作用,最终的结晶形态与单独添加这一成核剂时iPP的结晶形态相类似;当两种成核剂的ΔT_Cp接近相同时,两者竞争成核,成核iPP的结晶形态表现为两种成核剂共同作用的结果。因此,通过改变α/β复合成核剂的复合比例即改变两种成核剂的添加浓度,进而改变其ΔT_Cp,可以得到结晶形态完全不同的iPP。采用Caze法对非等温动力学进行了研究,结果表明：添加α/β复合成核剂能够提高iPP的结晶温度,缩短半结晶时间。复合成核剂成核iPP的结晶行为也同样受成核剂ΔT_Cp的影响,复合成核iPP的Avrami指数接近于复合体系中ΔT_Cp较大的成核剂单独添加时iPP的Avrami指数。     

α/β复合成核剂调控聚丙烯结晶过程的研究进展

综述了3类广泛应用的α/β复合成核剂对聚丙烯结晶动力学、结晶形态及宏观性能等方面影响的研究进展。总结了影响α/β复合成核剂调控聚丙烯结晶的主要因素在于两种成核剂的成核能力,具体表现为其成核聚丙烯结晶温度(TC)的高低:TC高的成核剂在聚丙烯结晶过程中起主导作用,TC低的成核剂基本不起成核作用,当两者的TC相接近时发生竞争成核。根据这一规律,找出了复合α、β两种成核剂的方法,并列举将其运用到调控聚丙烯的结晶过程中的实例。     

Non-Isothermal crystallization of isotactic polypropylene in dotriacontane. I: Effects of dilution,cooling rate,and nucleating agent addition on overall crystallization kinetics

The overall non-isothermal crystallization kinetics for nucleated and non-nucleated isotactic polypropylene (iPP) in dotriacontane systems was investigated. Adipic acid was used as the nucleating agent. Crystallization peak temperature was determined via differential scanning calorimetry as a function of the experimentally controlled variables iPP concentration, cooling rate, and nucleating agent concentration. The influence of these variables on crystallization mechanism and spherulitic structure as implied by the Ozawa and Ziabicki analyses was determined. The non-isothermal crystallization kinetics presented here are the first for iPP-diluent systems with and without nucleating agent.     

Effect of nano-nucleating agent addition on the isothermal and nonisothermal crystallization kinetics of isotactic polypropylene

Using differential scanning calorimetry (DSC) technique, a comparative study has been made of the isothermal and nonisothermal crystallization kinetics of nonnucleated isotactic polypropylene (iPP) and of nucleated iPP with 0.5 wt% of single-walled carbon nanotubes (SWCNTs) as a nucleating agent. The Avrami exponents (n) of iPP and nucleated iPP are close to 3.0 for isothermal crystallization. These results indicate that the addition of nucleating agents did not change the crystallization growth patterns of the neat polymer and that crystal growth was heterogeneous three-dimensional spherulitic. The results show that the addition of SWCNTs can shorten the crystallization half-time (t _1/2) and increase the crystallization rate of iPP. In the nonisothermal crystallization process, the Ozawa model failed to describe the crystallization behavior of nucleated iPP. The Cazé–Chuah model successfully described the nonisothermal crystallization process of iPP and its nanocomposite. A kinetic treatment based on the Ziabicki theory is presented to describe the kinetic crystallizability, in order to characterize the nonisothermal crystallization kinetics of iPP and nucleated iPP. Polarized light microscopy (PLM) experiments reveal that SWCNTs served as nucleating sites, resulting in a decrease of the spherulite size.     

两种羧酸盐成核剂的制备及其对聚丙烯的成核效果研究

合成了两种具有相似化学结构的聚丙烯（iPP）α晶型成核剂二环［2.2.1］庚⁃5⁃烯⁃2,3⁃二羧酸钠（NA₁）和二环［2.2.1］庚烷⁃2,3⁃二羧酸钠（NA₂）,研究了其在iPP中的成核效果。首先,利用差示扫描量热仪（DSC）和偏光显微镜（PLM）分别考察了两种成核剂对iPP结晶行为的影响。结果表明,当NA₁和NA₂的含量为0.3 %（质量分数,下同）时,iPP的结晶峰值温度分别提升了14.5 ℃和16.0 ℃。同时,两种成核剂都能够明显细化iPP球晶尺寸。其次,利用广角X射线衍射仪（WXAD）对成核iPP进行了表征,两种成核剂都诱导iPP产生了α晶型,说明均为α晶型成核剂。然后,对成核iPP的力学性能进行了表征。结果表明,随着两种成核剂用量的增加,iPP的拉伸强度和弯曲模量呈现先升高后平稳的趋势。当NA₁和NA₂含量为0.05 %时,成核iPP的拉伸强度较纯iPP分别提升了4.6 %和8.6 %,弯曲模量分别提升了8.2 %和21.7 %;冲击强度基本保持不变。     

The correlation between crystal structure and nucleation efficiency of a lithium (I) complex on isotactic polypropylene

In this work, 2,2′-methylene-bis-(4,6-di-t-butylphenylene)phosphate lithium (NA03) was synthesized and its crystal structural characterization was obtained by single crystal X-ray diffusion. The crystal data showed geometrically the cell parameter of NA03 matched with isotactic polypropylene (iPP), the a cell dimension was about two times to the value of cell edge of (010)_iPP. The disregistry was 2.89%, which was under the upper limit between the lattice matching spacing of host and guest crystals. Then NA03 was proved to be a highly effective nucleating agent for iPP through studying crystallization behaviors, crystallization morphologies, and mechanical properties of iPP nucleated with NA03. The outstanding nucleation efficiency could be attributed to the lattice matching between nucleating agent and iPP. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nucleation effects of sodium and ammonium salts of 2,2′‐methylene‐bis‐(4,6‐di‐t‐butylphenylene)phosphate in isotactic polypropylene

The nucleation ability of isotactic poly(propylene) (iPP) to ammonium 2,2′‐methylene‐bis‐(4,6‐di‐t‐butylphenylene) phosphate (An) was investigated in the present work comparing with sodium 2,2′‐methylene‐bis‐(4,6‐di‐t‐butylphenylene) phosphate (NA‐11). Scanning electron microscope (SEM) revealed the crystalline morphology of both An and NA‐11 with planar surface characteristics. The observation of the fracture surface of nucleation iPP samples by SEM showed An particles were dispersed uniformly in polymer and had a better compatibility with iPP matrix than NA‐11 particles. Differential scanning calorimeter (DSC) showed that the melting temperature of An was 262°C significantly lower than that measured from NA‐11 group (above 400°C). Crystallization behaviors of iPP/NA‐11 and iPP/An were also investigated by DSC analysis, respectively. The results showed the crystallization peak temperature and the crystallinity of iPP/An were almost near to that of iPP/NA‐11. Furthermore, mechanical and optical properties of iPP were strongly improved in the presences of An and NA‐11. The flexural strength of iPP was elevated 34 and 35% and the haze value was reduced from 40.4 to 15.1 and 14.9% by the addition of 0.15 wt% NA‐11 and An, respectively. These results demonstrate that the nucleating agent of An described here is a good nucleating agent for the crystallization of iPP as well as NA‐11. POLYM. ENG. SCI., 55: 22–28, 2015. © 2014 Society of Plastics Engineers     

β成核剂含量对等规聚丙烯性能的影响

研究了一种β成核剂(CHB-5)的含量对等规聚丙烯(iPP)结晶性能和力学性能的影响。用广角X射线衍射(WAXD)研究CHB-5诱导iPP晶型的变化,用差示扫描量热法(DSC)分析CHB-5对iPP熔融行为和结晶行为的影响,用偏光显微镜(POM)观察CHB-5诱导iPP结晶形态的变化。结果表明,CHB-5的加入使iPP的成核能力增强;CHB-5可降低iPP的熔融温度,提高其结晶温度和结晶起始温度,加快结晶速率;CHB-5能降低球晶尺寸;CHB-5的加入可使iPP缺口冲击强度提高。     

Influence of a nucleating agent on the crystallization behaviour of isotactic polypropylene and elastomer blends

The influence of a nucleating agent on the crystallization behaviour of isotactic polypropylene (iPP), in their blends with poly(styrene-b-ethylene butylene-b-styrene) (SEBS), and a metallocenic ethylene-octene copolymer (EO) was investigated by DSC, optical microscopy and real-time small and wide angle X-ray scattering (SAXS and WAXS) experiments using synchrotron radiation. In non-nucleated iPP/SEBS blends, the crystallization of the iPP matrix occurred in the presence of the styrenic domains which induced a nucleating effect on the process, as observed in the synchrotron experiments. The metallocenic elastomer did not affect the crystallization behaviour of iPP in the iPP/EO blends in non-isothermal experiments, however, the development of crystallinity in the elastomer was restricted. In the nucleated isotactic polypropylene/elastomer blends a significant increase in the crystallinity and the crystallization rate of the iPP matrix was observed due to the presence of the nucleating agent. However, the nucleating efficiency of the additive was strongly affected by the nature and content of the elastomeric component. The nucleating agent efficiency was higher in the presence of the ethylene-octene component than the styrenic elastomer.     

Effects of melt structure on crystallization behavior of isotactic polypropylene nucleated with α/β compounded nucleating agents

In this study, the melt structure of isotactic polypropylene (iPP) nucleated with α/β compounded nucleating agents (α/β‐CNA, composed of the α‐NA of 0.15 wt % Millad 3988 and the β‐NA of 0.05 wt % WBG‐II) was tuned by changing the fusion temperature T_f. In this way, the role of melt structure on the crystallization behavior and polymorphic composition of iPP were investigated by differential scanning calorimetry (DSC), wide‐angle X‐ray scattering (WAXD) and scanning electron microscopy (SEM). The results showed that when T_f = 200°C (iPP was fully molten), the α/β‐CNA cannot encourage β‐phase crystallization since the nucleation efficiency (NE) of the α‐NA 3988 was obviously higher than that of the β‐NA WBG‐II. Surprisingly, when T_f was in 179–167°C, an amount of ordered structures survived in the melt, resulting in significant increase of the proportion of β‐phase (achieving 74.9% at maximum), indicating that the ordered structures of iPP played determining role in β‐phase crystallization of iPP nucleated with the α/β‐CNA. Further investigation on iPP respectively nucleated with individual 3988 and WBG‐II showed that as T_f decreased from 200°C to 167°C, the crystallization peak temperature T_c of iPP/3988 stayed almost constant, while T_c of iPP/WBG‐II increased gradually when T_f < 189°C and became higher than that of iPP/3988 when T_f decreased to 179°C and lower, which can be used to explain the influence of ordered structure and α/β‐CNA on iPP crystallization. Using this method, the selection of α‐NA for α/β‐CNA can be greatly expanded even if the inherent NE of β‐NA is lower than that of the α‐NA. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41355.     

Combined effect of organic phosphate sodium and nanoclay on the mechanical properties and crystallization behavior of isotactic polypropylene

Combined effect of α‐nucleating agent (NA) sodium 2,2′‐methylene‐bis(4,6‐di‐tert‐butylphenyl) phosphate (NA11) and nanoclay (NC) on the mechanical properties and crystallization behavior of isotactic polypropylene (iPP) was investigated by mechanical testing, wide‐angle X‐ray scattering (WAXD), differential scanning calorimetry (DSC), polarized optical microscopy (POM), and scanning electron microscopy (SEM). The mechanical testing results indicated that the separate addition of NA11 and NC only increased the stiffness of iPP while the combined addition of NA11, NC, and maleic anhydride grafted polypropylene (PP‐g‐MA) simultaneously improved stiffness and toughness of iPP. Compared to pure iPP, the tensile strength, the flexural modulus, and impact strength of iPP composites increased 9.7, 38.6, and 42.9%, respectively. The result indicated good synergistic effects of NC, NA11, and PP‐g‐MA in improving iPP mechanical properties. WAXD patterns revealed NA11, and NC only induced the α‐crystals of iPP. SEM micrograph showed that the PP‐g‐MA could effectively improve the dispersing of NC in iPP. Finally, the nonisothermal crystallization kinetics of neat iPP and PP nanocomposites was described by Caze method. The result indicated that the addition of NA overcame the shortcoming of low crystallization rate of NC nanocomposites and maintained the excellent mechanical properties, which is another highlight of the combined addition of NAs and nanoclay. Meanwhile, the result showed that nuclei formation and spherulite growth of iPP were affected by the presence of NA and nanoclay. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of supercritical carbon dioxide-assisted nano-scale dispersion of nucleating agents on the crystallization behavior and properties of polypropylene

This work aims at using supercritical carbon dioxide (scCO₂) to disperse a nucleating agent, sodium 2,2-methylene-bis (4,6-di-tert-butylphenyl) phosphate, denoted as NA40, in an isotactic polypropylene (PP) on the nanometer scale and at studying the nucleating efficiency of the nano-dispersed NA40 by differential scanning calorimeter (DSC) and polarized optical microscope (POM). The Avrami equation and a model combining Avrami equation and Ozawa equation were used to describe the isothermal and non-isothermal crystallization kinetics of the nucleated PP, respectively. The results showed a consistent trend: both the isothermal crystallization rate and the non-isothermal crystallization temperature of the PP in which NA40 was dispersed under scCO₂ were higher than those of the virgin PP and the PP in which the same amount of NA40 was incorporated by a classical extruder compounding process. Moreover, the size of the spherulites and the haze of the former PP were smaller than those of the virgin PP and the latter. The trend was reversed in terms of flexural and tensile strengths.     

Crystallization characteristics of isotactic polypropylene with and without nucleating agents

Nucleation effects of two sorbitol derivatives on the crystallization of isotactic polypropylene (iPP) were studied by means of differential scanning calorimetry (DSC) and polarized optical microscopy (POM). A nonisothermal crystallization kinetic equation was employed to analyze the crystallization characteristics of iPP with or without the nucleating agents from DSC crystallization thermograms. The equilibrium melting temperature of iPP necessary for the kinetic study was obtained by the extrapolation method to be 209°C. The nonisothermal crystallization kinetic analysis for the unnucleated iPP at different cooling rates was possible by assuming the spherulite growth initiated simultaneously by heterogeneous and homogeneous nucleation. On the other hand, the crystallization kinetics of the nucleated iPP could be described by the heterogeneous nucleation and growth process alone. The addition of the nucleating agents up to their saturation concentrations in iPP increased the crystallization peak temperature by 17°C, and the number of effective nuclei by three orders of magnitude. A high concentration of the nucleating agents caused agglomeration of the agents to lower the number of effective nuclei.     

A comparative study of polypropylene nucleated by individual and compounding nucleating agents. I. Melting and isothermal crystallization

In this study, melting and isothermal crystallization behaviors of polypropylene (PP) nucleated with different nucleating agents (NAs) have been comparatively studied. α‐phase NA 1,3 : 2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988), β‐phase NA aryl amides compound (TMB‐5), and their compounds were introduced into PP matrix, respectively. The crystallization and melting characteristics as well as the crystallization structures and morphologies of nucleated PP were studied by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). As indicated by previous work that a few amounts of α‐phase NA (DMDBS) or β‐phase NA (TMB‐5) has apparent nucleation effect for PP crystallization. However, the crystallization of PP nucleated with compounding NAs is dependent on the content of each NA. In the sample of PP with 0.1 wt % DMDBS and 0.1 wt % TMB‐5, the nucleation efficiency of TMB‐5 is much higher than that of DMDBS and PP crystallization is mainly nucleated by TMB‐5, and in this condition, β‐phase PP is the main crystallization structure. For the sample of PP with 0.2 wt % DMDBS and 0.2 wt % TMB‐5, 0.2 wt % DMDBS has higher nucleation efficiency than 0.2 wt % TMB5, and α‐phase is the main crystalline structure in this sample. The isothermal crystallization kinetics and crystallization structure have been analyzed in detail in this work. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Variation of non‐isothermal crystallization behavior of isotactic polypropylene with varying β‐nucleating agent content

The non‐isothermal crystallization behavior, the crystallization kinetics, the crystallization activation energy and the morphology of isotactic polypropylene (iPP) with varying content of β‐nucleating agent were investigated using differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The DSC results showed that the Avrami equation modified by Jeziorny and a method developed by Mo and co‐workers could be successfully used to describe the non‐isothermal crystallization process of the nucleated iPPs. The values of n showed that the non‐isothermal crystallization of α‐ and β‐nucleated iPPs corresponded to a tridimensional growth with homogeneous and heterogeneous nucleation, respectively. The values of crystallization rate constant showed that the rate of crystallization decreased for iPPs with the addition of β‐nucleating agent. The crystallization activation energy increased with a small amount (less than 0.1 wt%) of β‐nucleating agent and decreased with higher concentration (more than 0.1 wt%). The changes of crystallization rate, crystallization time and crystallization activation energy of iPPs with varying contents of β‐nucleating agent were mainly determined by the ratio of the content of α‐ and β‐phase in iPP (α‐PP and β‐PP) from the DSC investigation, and the large size and many intercrossing lamellae between boundaries of β‐spherulites for iPPs with small amounts of β‐nucleating agent and the small size and few intercrossing bands among the boundaries of β‐spherulites for iPPs with large amounts of β‐nucleating agent from the SEM examination. Copyright © 2010 Society of Chemical Industry     

新型高效聚丙烯β晶型成核剂

采用差示扫描量热仪和广角X射线衍射仪考察了降冰片烯十二酰胺酸的不同金属盐对聚丙烯晶型结构的影响。结果表明,0.2 ％（质量分数,下同）的降冰片烯十二酰胺酸锌盐（NBDA30）能够诱导聚丙烯产生高含量的β晶型（k值为81.7 ％）。在此基础上进一步研究了N BDA30的添加含量对聚丙烯力学性能和结晶性能的影响。结果表明,当成核剂添加量超过0.4 ％时,聚丙烯的冲击强度和结晶温度开始提高,球晶尺寸开始减小;冲击强度最大值在0.8 ％时取得,冲击强度从纯聚丙烯的31.8 J/m提高到91.0 J/m,提高幅度约为3倍;同时NBDA30成核聚丙烯的拉伸强度和弯曲模量没有明显降低。     

Influence of a particulate nucleating agent on the quiescent and flow-induced crystallization of isotactic polypropylene

Flow induced crystallization of commercial isotactic polypropylene (iPP) and its blends with sodium 2,2′-methylene bis-(4,6-di-tert-butylphenyl) phosphate (also known as NA11) is studied by means of in-situ time resolved small-angle X-ray scattering (SAXS). The isothermal crystallization at 145 °C (i.e. well below melting temperature of polymer) is performed after the application of steady shear to probe the anisotropic structure formation. In order to separate the influence of shear rate and shear time on polymer crystallization, four different shear conditions (60 s⁻¹ for 1 s, 30 s⁻¹ for 2 s, 15 s⁻¹ for 4 s and 6 s⁻¹ for 10 s) are applied while maintaining the same imposed strain in the polymer melt. Further the effect of different concentration of nucleating agent on the crystallization kinetics of iPP is examined both under quiescent and shear flow conditions. For instance, under quiescent condition, the crystallization half-time (τ_1/2) decreases with the increasing concentration of nucleating agent in the polymer. Under shear flow conditions, our observations are as follows: In the case of neat iPP, τ_1/2 decreases significantly at higher shear rates (≥30 s⁻¹). Compared to the neat iPP, for the same concentration of NA11 in the NA11/iPP blends differences in τ_1/2 with the increase in applied shear rates are significantly smaller. In other words, the crystallization kinetics is dominated by the amount of nucleating agent in the NA11/iPP blends as opposed to shear rates in the neat iPP. The present study shows that the critical value of shear rate required for chain orientation in the molten polymer is lower in the presence of the nucleating agent compared to neat iPP. The self-nucleation process investigated with the aid of differential scanning calorimetry (DSC), indicates that the nucleating efficiency of NA11 on iPP is around 60%.     

Influence of different β‐nucleating agent on crystallization behavior,morphology, and melting characteristic of multiwalled carbon nanotube‐filled isotactic polypropylene nanocomposites

To obtain isotactic polypropylene (iPP) nanocomposites with high β‐crystal content, TMB5, calcium pimelate and calcium pimelate supported on the surface of nano‐CaCO₃ were used as β‐nucleating agent and MWCNT filled β‐nucleated iPP nanocomposites were prepared. The effect of different β‐nucleating agent and MWCNT on the crystallization behavior and morphology, melting characteristic and β‐crystal content of β‐nucleated iPP nanocomposites were investigated by DSC, XRD and POM. The results indicated that addition of MWCNT increased the crystallization temperature of iPP and MWCNT filled iPP nanocomposites mainly formed α‐crystal. The β‐nucleating agent can induce the formation of β‐crystal in MWCNT filled iPP nanocomposites. The β‐nucleating ability and β‐crystal content in MWCNT filled β‐nucleated iPP nanocomposites decreased with increasing MWCNT content and increased with increasing β‐nucleating agent content due to the nucleation competition between MWCNT and β‐nucleating agents. It is found that the calcium pimelate supported on the surface of inorganic particles as β‐nucleating agent has stronger heterogeneous β‐nucleation than calcium pimelate and TMB5. The MWCNT filled iPP nanocomposites with high β‐crystal content can be obtained by supported β‐nucleating agent. POLYM. COMPOS., 36:635–643, 2015. © 2014 Society of Plastics Engineers     

Polystyrene as a versatile nucleating agent for polypropylene

The morphology of isotactic polystyrene (iPS) particles which had been compounded into an isotactic polypropylene (iPP) matrix was varied in-situ by selective heat treatment to be either amorphous (iPS_amorphous) or semicrystalline (iPS_crystalline). The influence of iPS morphology on the quiescent and shear-induced isothermal crystallisation of iPP was then studied using differential scanning calorimetry (DSC), in-situ simultaneous small and wide angle X-ray scattering (SAXS/WAXS) and polarised optical microscopy (POM). In the quiescent condition iPS_crystalline was found to selectively nucleate the β phase while iPS_amorphous nucleated the α phase of iPP. Compared to the control sample (iPP_control), the presence of both morphologies of iPS increased the number of shear-induced oriented crystal precursors that form as a result of the step shear. During isothermal crystallisation the shear-induced nuclei promote oriented α form crystal growth, accelerate the crystallisation kinetics and ultimately swamp the effect of the nucleating particles present.     

A novel highly efficient β‐nucleating agent for isotactic polypropylene

A novel highly efficient β‐nucleating agent for isotactic polypropylene (iPP), hexahydrophthalic barium (HHPA‐Ba), was found and its effects on the mechanical properties, the β‐phase content, and crystallization behavior of iPP were investigated, respectively. The results show that the β‐phase content of nucleated iPP (k_β value) can reach 80.2% with 0.4 wt % HHPA‐Ba. The impact strength and crystallization peak temperature of nucleated iPP are greatly increased. Compared with pure iPP, the impact strength of nucleated iPP can increase 2.4 times. Meanwhile, the spherulite size of nucleated iPP is dramatically decreased than that of pure iPP. The Caze method was used to investigate the nonisothermal crystallization kinetics of nucleated iPP and the crystallization active energy was achieved by Kissinger method. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011