Thermal dynamics of wallboard with latent heat storage

Wallboard impregnated with phase change material (PCM) will provide thermal storage that is distributed throughout a building, enabling passive solar design and off-peak cooling with frame construction. This paper examines the thermal dynamics of PCM wallboard that is subjected to the diurnal variation of room temperature, but is not directly illuminated by the sun. The purpose of this work is to provide guidelines useful in selecting an optimal PCM and in estimating the benefits of PCM architectural products. The energy stored during a daily cycle depends upon a) the melt temperature of the PCM; b) the temperature range over which melt occurs; and c) the latent capacity per unit area of wallboard. Situations with the wallboard on an interior partition or on the inside of the building envelope are investigated separately. The following findings are presented. The maximum diurnal energy storage occurs at a value of the PCM melt temperature that is close to the average room temperature in most circumstances. Diurnal energy storage decreases if the phase change transition occurs over a range of temperatures. The diurnal storage achieved in practice may be limited to the range 300–400 kJ/m², even if the wallboard has a greater latent capacity. The implications of these findings for test room experiments are discussed.     

Comparative study of room temperature control in buildings with and without the use of PCM in walls

The concept of thermal energy storage in building gains a specific importance in the present energy scenario related to energy consumption and indoor thermal comfort. The material used to store the thermal energy which undergoes a phase change referred as PCM and it is considered as a possible solution for reducing energy consumption in the building by storing and releasing heat within a certain temperature range; it raises the building inertia and also stabilizes indoor air temperature fluctuations. The room temperature is controlled by imposing PCM inside the walls. An attempt has been made to compare room air temperature with and without the use of PCM inside the walls of constructed modular building unit. The PCM imposed modular building shows the reduced temperature fluctuations in room, the PCM absorbs and liberates excess heat which is gained from the outer side of the room and maintains constant inner room temperature. The PCM imposed walls of modular building unit have an ability to reduce 10–30% of heat load in comparison with the plain wall. The results showed that reduction in room temperature is about 2–4°C and it has been concluded that the PCM imposed modular building unit has more energy saving opportunities than normal modular building unit.     

Optimal roof structure with multilayer cooling function materials for building energy saving

Both cool roof and phase change thermal storage are promising technologies in decreasing building energy consumption. Combining these two technologies is likely to further enhance the thermal comfort of the building as well as reduce air condition loads. In this paper, the cooling performance and energy-saving effects of four types of roof (normal roof, phase change material [PCM] roof, cool roof, and cool PCM roof [cool roof coupled with PCM]) were investigated under a simulated sunlight. Experimental results indicate that compared with normal roof, the other three roofs are able to narrow the indoor temperature fluctuation and decrease the heat flow entering into the room. Among them, cool PCM roof gave the best energy-saving effect that can lower the indoor temperature and heat entering into rooms by 6.6°C and 52.9%, respectively. Besides, the PCM location, PCM thickness, and insulation thickness exerted great impacts on the cooling performance of the roof. Placing the PCM on the internal layer beneath the extruded polystyrene (XPS) insulation board can make the indoor temperature 1.2°C lower than that on the middle layer. Although thicker PCM panels or insulation boards can provide a better thermal insulation, 5 mm in PCM thickness and 20 mm in insulation thickness are enough to guarantee the indoor temperature of cool PCM roof system at a comfortable range (22°C-28°C) for a whole day. These findings will give guidance in designing buildings with a light and compact roof structure to decrease energy consumption and improve comfort level.     

温控下被动式太阳房辅助热源量的动态分析

减少对辅助热源的依赖是太阳能建筑设计的一个重要目标,利用建筑自身的集热蓄热能力,可以减少辅助热源量.研究了根据一维热网络模型、温控下辅助热源量的计算公式及热平衡方程,计算不同辅助热源的控制常数以及设定温度下室内温度和辅助热源量的变化;分析了不同的热源控制常数取值和设定温度对室内温度和辅助热源量的影响;讨论了设定温度对墙体蓄热利用的影响.     

Thermal analysis of a direct-gain room with shape-stabilized PCM plates

The thermal performance of a south-facing direct-gain room with shape-stabilized phase change material (SSPCM) plates has been analysed using an enthalpy model. Effects of the following factors on room air temperature are investigated: the thermophysical properties of the SSPCM (melting temperature, heat of fusion and thermal conductivity), inner surface convective heat transfer coefficient, location and thickness of the SSPCM plate, wall structure (external thermal insulation and wallboard material) etc. The results show that: (1) for the present conditions, the optimal melting temperature is about 20 °C and the heat of fusion should not be less than 90 kJ kg⁻¹; (2) it is the inner surface convection, rather than the internal conduction resistance of SSPCM, that limits the latent thermal storage; (3) the effect of PCM plates located at the inner surface of interior wall is superior to that of exterior wall (the south wall); (4) external thermal insulation of the exterior wall obviously influences the operating effect and period of the SSPCM plates and the indoor temperature in winter; (5) the SSPCM plates create a heavyweight response to lightweight constructions with an increase of the minimum room temperature at night by up to 3 °C for the case studied; (6) the SSPCM plates really absorb and store the solar energy during the daytime and discharge it later and improve the indoor thermal comfort degree at nighttime.     

Passive room conditioning using phase change materials—Demonstration of a long-term real size experiment

The thermal properties of lightweight buildings can be efficiently improved by using phase change materials (PCMs). The heat storage capacity of the building can be extended exactly at the desired temperature level, which leads to an enormous increase in residential comfort. This is shown in the present paper using the example of a prefabricated wooden house. The house was divided into two identical rooms. One of them was equipped with almost one ton of phase change material based on salt hydrates with a melting temperature of approx. 21°C. The material was encapsulated in 1-l Polyethylene containers and installed in two back-ventilated layers inside of the walls. The house was monitored for a period of 87 days in terms of temperatures, solar radiation and air velocity inside the PCM wall system. A considerable temperature buffering could be observed in the PCM room compared to the reference room. An overall reduction of the temperature fluctuations of 57% and a reduction of the day/night fluctuations of 62% compared to the reference room could be obtained. In addition, a prediction regarding the energy demand of such buildings is discussed on the basis of a simulation program. Thus, the annual cooling capacity can be reduced by 36.5% compared to the regular timber construction technique by introducing PCM. Furthermore, the good correlation of the simulation results with the experimental ones allows using the simulation as a tool to design a house with additional thermal storages.     

应用于日光温室墙体的相变材料热物性优化研究

建立日光温室计算传热模型,以室内空气温度和墙体内表面温度为指标,通过实验方法验证了所建立的传热模型准确性,最后分析相变材料相变温度、相变焓、导热系数、密度等热物性对室内最低温度和相变蓄热率的影响规律,确定被动式相变蓄热墙体和主-被动式相变蓄热墙体的最佳相变材料热物性,阐明了实际应用时相变材料选择原则。研究结果表明,所建立的日光温室传热模型具有较高准确性,可用于日光温室墙体相变材料热物性优化;主-被动式相变蓄热墙体最佳相变材料的相变温度为27 ℃,相变焓为200 kJ/kg,导热系数为0.35 W/（m·K）,密度为440 kg/m³,被动式相变蓄热墙体最佳相变材料的相变温度为26 ℃,相变焓为200 kJ/kg,导热系数为0.35 W/（m·K）,密度为792 kg/m³;最佳相变材料热物性应用时,2种墙体室内最低温度均可达到15.0 ℃,但是被动式相变蓄热墙体的相变蓄热率较主-被动式相变蓄热墙体减小29.5%。本研究可为相变材料在日光温室的高效利用提供参考。     

The application of a validated numerical model to predict the energy conservation potential of using phase change materials in the fabric of a building

Phase change materials absorb a large amount of energy as latent heat at a constant phase transition temperature and are thus used for passive heat storage and temperature control, example applications include electronics, and storage of perishable items. Encapsulated phase change materials incorporated into gypsum wallboards of buildings may be suitable for absorbing solar energy directly, reducing temperature rise. Improvement in human comfort is to be expected due to a decrease in the frequency and magnitude of internal air temperature swings, maintaining the temperature closer to the desired set temperature passively for a long period of time.This paper summarises the results of a detailed theoretical investigation and analysis of thermal energy storage and temperature control achieved using passive building construction elements incorporating phase change materials. The predictions detail the effects of using various quantities of different PCM materials with phase change temperatures of 28 and 43 °C incorporated into a selection of wall constructions for selected ambient conditions of temperature and insolation. From this parametric study, optimum arrangements are proposed.     

Investigations on thermal and optical performances of a glazing roof with PCM layer

The thermal and optical performances of a roof in a building containing phase change material (PCM) were investigated in this paper. The glazing roof model consists of two layers of glass and one layer of PCM. The purpose of filling the roof structure with PCM is to utilize the solar energy efficiently. The effectiveness of thermal and optical performances of the roof PCM system was determined by analyzing the heat flux and temperature at the indoor surface with different absorption coefficients and refractive index of PCM in solid and liquid states. The results show that the absorption coefficients and refractive index of solid and liquid PCMs have both effects on thermal performance in the roof PCM system. Of all the thermal performances, the effect on internal temperature, temperature lag, and total transmitted energy is smaller and the effect on solar transmittance and transmitted solar energy is bigger. The absorption coefficients have the opposite effect with the refractive index on interior temperature lag. Considering the indoor daylight, increasing the refractive index and absorption coefficient of liquid PCM is a better method to better the thermal performance of a roof PCM system. Copyright © 2017 John Wiley & Sons, Ltd.     

Isothermal storage of solar energy in building construction

The role of advanced isothermal heat storage systems in buildings is discussed. A storage system encapsulated with phase change materials in which energy is absorbed in the hot period and released in the cold period is analyzed. The thermal behaviour of isothermal heat storage composites is examined using numerical techniques.Two methods of heat transfer with latent heat storage are described in the first part. Based on the initial results, the “effective heat capacity” method was selected and implemented into ESP-r. Numerical studies on the effect of isothermal storage of solar energy in specific building material components are discussed in the second part. Numerical simulations were conducted for two cases of multi-zone, highly glazed and naturally ventilated passive solar buildings. PCM-impregnated gypsum plasterboard was used as an internal room lining in the first case study and transparent insulation material combined with PCM was applied for the external south-oriented wall in the second case study. The behaviour of a TIM–PCM wall and its influence on the internal surface temperature are estimated. Air, surface and resultant temperatures are compared with a “no-PCM” case for both case studies and the diurnal and the seasonal latent heat storage effect is analyzed.     

An assessment of mixed type PCM-gypsum and shape-stabilized PCM plates in a building for passive solar heating

Thermal performance of two phase change material (PCM) composites, mixed type PCM-gypsum and shape-stabilized PCM plates, has been numerically evaluated in a passive solar building in Beijing with an enthalpy model. Effects of the melting temperature and phase transition zone of the PCM are analyzed and a comparison between the two types of PCM composites is performed. The results show that: (1) for the present conditions, the optimal melting temperature is about 21 °C; (2) PCM composites with a narrow phase transition zone provide better thermal performance; (3) both mixed type PCM-gypsum and shape-stabilized PCM plates effectively shave the indoor temperature swing by 46% and 56%, respectively; (4) the shape-stabilized phase change material (SSPCM) plates respond more rapidly than the mixed type PCM-gypsum and prove to be thermally more effective in terms of utilizing the latent heat.     

Field thermal performance of naturally ventilated solar roof with PCM heat sink

For decades, residential and commercial roofs have been considered a prime location for installation of building integrated solar systems. In climatic conditions of East Tennessee, USA, an experimental solar roof was tested during 2009/2010, by a research team representing Metal Construction Association (MCA), and a consortium of building insulation companies, photovoltaic (PV) manufacturers, and energy research centers. The main objective was to thermally evaluate a new roofing technology utilizing amorphous silicon PV laminates integrated with the metal roof panels. In order to mitigate thermal bridging and reduce roof-generated thermal loads, this novel roof/attic assembly contained a phase change material (PCM) heat sink, a ventilated air cavity over the roof deck, and thermal insulation with an integrated reflective surface. During winter, the experimental roof was expected to work as a passive solar collector storing solar heat absorbed during the day, and increasing overall attic air temperature during the night. During summer, the PCM was expected to act as a heat sink, reducing the heat gained by the attic and consequently, lowering the building cooling-loads.In this paper, field thermal performance data of the experimental PV-PCM roof/attic system are presented and discussed. Performance of the PV-PCM roof/attic is evaluated by comparing it to a control asphalt shingle roof. The test results showed about 30% heating and 50% cooling load reductions are possible with the experimental roof configuration.     

Effect of phase change material on passive thermal heating of a greenhouse

In this study, a periodic analysis of a greenhouse with combination of phase change material (PCM) and insulation as a north wall has been developed for thermal heating. The thermal model is based on Fourier analysis. Effect of distribution of PCM thickness on plant and room air temperature has been studied in detail. The plant and room air temperature have been evaluated with and without north wall. Numerical computations have been carried out for a typical winter day of New Delhi. On the basis of numerical results, it is inferred that (i) there is a significant effect of PCM north wall and heat capacity of plant temperature during off‐sunshine hour due to storage effect and (ii) the rate of heat flux inside greenhouse from north wall is maximum for least thickness of PCM. Copyright © 2005 John Wiley & Sons, Ltd.     

Nonlinear coupling between thermal mass and natural ventilation in buildings

An ideal naturally ventilated building model that allows a theoretical study of the effect of thermal mass associating with the non-linear coupling between the airflow rate and the indoor air temperature is proposed. When the ventilation rate is constant, both the phase shift and fluctuation of the indoor temperature are determined by the time constant of the system and the dimensionless convective heat transfer number. When the ventilation rate is a function of indoor and outdoor air temperature difference, the thermal mass number and the convective heat transfer air change parameter are suggested. The new thermal mass number measures the capacity of heat storage, rather than the amount of thermal mass. The analyses and numerical results show that the non-linearity of the system does neither change the periodic behaviour of the system, nor the behaviour of phase shift of the indoor air temperature when a periodic outdoor air temperature profile is considered. The maximum indoor air temperature phase shift induced by the direct outdoor air supply without control is 6 h.     

Numerical and experimental analysis of convection heat transfer in passive solar heating room with greenhouse and heat storage

In this paper, heat transfer and air flow in passive solar heating room with greenhouse and heat storage are studied. Thermal insulation of solar heating room has significant effects on temperature distribution and airflow in the heating chamber of this solar system. Heat transfer and air flow in a rock bed, which is used as solar absorber and storage layer, are also studied. If porosity is kept within certain range, increasing the rock size causes an increase of the capability of thermal storage and heating effects; increasing the porosity of thermal storage materials results in an increase of the bed temperature but a decrease of the rock mass. The specific heat capacity and thermal conductivity have a remarkable effect on the average temperature of rock bed. All these factors should be taken into account when designing a solar heating system.     

Energy analysis of space solar dynamic heat receivers

Energy analysis of space solar dynamic heat receivers employing solid–liquid phase change storage is developed. The heat receiver is a critical component of a solar dynamic system. Phase change thermal energy storage is used in the heat receiver. The energy analysis presented here can be used to understand the energy transfer in the heat receiver and thermal energy storage in phase change materials (PCM). The heat receiver cavity radiation mathematical model and the working fluid tube heat model are established. Energy loss, energy absorbed by gas, the latent and sensible thermal energy storage in PCM, maximum tube temperature, gas outlet temperature and liquid PCM fraction were calculated. The results are analyzed and could be used in heat receiver design.     

Performance analysis of a latent heat storage system with phase change material for new designed solar collectors in greenhouse heating

The continuous increase in the level of greenhouse gas emissions and the rise in fuel prices are the main driving forces behind the efforts for more effectively utilize various sources of renewable energy. In many parts of the world, direct solar radiation is considered to be one of the most prospective sources of energy. In this study, the thermal performance of a phase change thermal storage unit is analyzed and discussed. The storage unit is a component of ten pieced solar air collectors heating system being developed for space heating of a greenhouse and charging of PCM. CaCl₂6H₂O was used as PCM in thermal energy storage with a melting temperature of 29 °C. Hot air delivered by ten pieced solar air collector is passed through the PCM to charge the storage unit. The stored heat is utilized to heat ambient air before being admitted to a greenhouse. This study is based on experimental results of the PCM employed to analyze the transient thermal behavior of the storage unit during the charge and discharge periods. The proposed size of collectors integrated PCM provided about 18–23% of total daily thermal energy requirements of the greenhouse for 3–4 h, in comparison with the conventional heating device.     

Thermal performance of PCM thermal storage unit for a roof integrated solar heating system

The thermal performance of a phase change thermal storage unit is analysed and discussed. The storage unit is a component of a roof integrated solar heating system being developed for space heating of a home. The unit consists of several layers of phase change material (PCM) slabs with a melting temperature of 29 °C. Warm air delivered by a roof integrated collector is passed through the spaces between the PCM layers to charge the storage unit. The stored heat is utilised to heat ambient air before being admitted to a living space. The study is based on both experimental results and a theoretical two dimensional mathematical model of the PCM employed to analyse the transient thermal behaviour of the storage unit during the charge and discharge periods. The analysis takes into account the effects of sensible heat which exists when the initial temperature of the PCM is well below or above the melting point during melting or freezing. The significance of natural convection occurring inside the PCM on the heat transfer rate during melting which was previously suspected as the cause of faster melting process in one of the experiments is discussed. The results are compared with a previous analysis based on a one dimensional model which neglected the effect of sensible heat. A comparison with experimental results for a specific geometry is also made.     

太阳能吸热器换热管蓄热数值模拟与试验研究

对以高温共晶盐LiF—CaF2为相变材料(PCM)和以干空气为工质的相变蓄热系统，采用焓方法建立了以控制体单元为对象的单管相变蓄热模型，并对系统进行了数值分析，得到了循环工质气体出口温度、相变材料容器最高温度和平均壁温等参数的瞬态变化曲线，实验研究了吸热器换热管的蓄傲热性能，分析了工质进口温度、输入热流级工质流量对工质出口温度、PCM容器平均壁温及最高壁温的影响。计算结果和试验表明单元换热管的蓄傲热性能达到了设计要求，试验结果与数值计算吻合良好。     

Application of a ground source heat pump system with PCM‐embedded radiant wall heating for buildings

This paper deals with the utilization of a renewable energy‐based integrated system with the latent heat storage option for building thermal management systems. Both energy and exergy‐based assessments of the current combined system are conducted. For this purpose, phase change material (PCM)‐embedded radiant wall heating system using solar heating and ground source heat pump (GSHP) is studied thermodynamically. Heat is essentially stored within the PCMs as used in the panels to increase the effectiveness. The stored heat is released when the solar energy is not available. In the thermal energy storage analyses, four different PCMs are considered. The present results show that the overall first ‐ law (energy) and second ‐ law (exergy) efficiencies of the PCM‐free radiant heating system are much lower than the case with the PCM‐embedded radiant heating system. Therefore, it is confirmed that the energy efficiency increases from 62% to 87% while the exergy efficiency rises from 14% to 56% with the option where SP26E PCM is employed accordingly.