A new grounded lamination gate (GLG) for diminished fringe-capacitance effects in high-/spl kappa/ gate-dielectric MOSFETs

A grounded lamination gate (GLG) structure for high-/spl kappa/ gate-dielectric MOSFETs is proposed, with grounded metal plates in the spacer oxide region. Two-dimensional device simulations performed on the new structure demonstrate a significant improvement with respect to the threshold voltage roll-off with increasing gate-dielectric constant (due to parasitic internal fringe capacitance), keeping the equivalent oxide thickness same. A simple fabrication procedure for the GLG MOSFET is also presented.     

The effect of high-K gate dielectrics on deep submicrometer CMOSdevice and circuit performance

The potential impact of high permittivity gate dielectrics on device short channel and circuit performance is studied over a wide range of dielectric permittivities (K_gate) using two-dimensional (2-D) device and Monte Carlo simulations. The gate-to-channel capacitance and parasitic fringe capacitances are extracted using a highly accurate three-dimensional (3-D) capacitance extractor. It is observed that there is a decrease in parasitic outer fringe capacitance and gate-to-channel capacitance in addition to an increase in internal fringe capacitance, when the conventional silicon dioxide is replaced by a high-K gate dielectric. The lower parasitic outer fringe capacitance is beneficial for the circuit performance, while the increase in internal fringe capacitance and the decrease in the gate-to-channel capacitance will degrade the short channel performance contributing to higher DIBL, drain leakage, and lower noise margin. It is shown that using low-K gate sidewalls with high-K gate insulators can decrease the fringing-induced barrier lowering. Also, from the circuit point of view, for the 70-nm technology generation, the presence of an optimum K_gate for different target subthreshold leakage currents has been identified     

Analysis of the Effects of Fringing Electric Field on FinFET Device Performance and Structural Optimization Using 3-D Simulation

In this paper, the potential impact of parasitic capacitance resulting from fringing field on FinFET device performance is studied in detail using a 3-D simulator implemented with quantum-mechanical models. It was found that fringing field from gate to source contributes significantly to FinFET performance and speed. The strength of fringing field is closely related to device features such as gate-dielectric thickness, the spacer width, fin width and pitch, as well as the gate height. For undoped fin with underlapping (nonoverlapping source/drain) gate, a thinner spacer with higher kappa value enhances the gate control of short-channel effects (SCEs) and reduces the source-to-drain leakage current. Our results also suggest that reducing the high- gate-dielectric thickness is no longer an effective approach to improve performance in small FinFET devices due to the strong fringing effect. However, the introduction of thin metal gate in a multifin device was found beneficial to device speed without compromising on current drive and SCE.     

Impact of High-k Gate Dielectrics on the Device and Circuit Performance of Nanoscale FinFETs

The impact of high-k gate dielectrics on device short-channel and circuit performance of fin field-effect transistors is studied over a wide range of dielectric permittivities k. It is observed that there is a decrease in the parasitic outer fringe capacitance C_of in addition to an increase in the internal fringe capacitance C_if with high-k dielectrics, which degrades the short-channel effects significantly. It is shown that fin width scaling is the most suitable approach to recover the degradation in the device performance due to high-k integration. Furthermore, from the circuit perspective, for the 32-nm technology generation, the presence of an optimum k for a given target subthreshold leakage current has been identified by various possible approaches such as fin width scaling, fin-doping adjustment, and gate work function engineering     

A 2-D analytical threshold-voltage model for GeOI/GeON MOSFET with high-k gate dielectric

A 2-D analytical threshold-voltage model for ultra-thin-body MOSFET with buried insulator and high-k gate dielectric is established by solving the 2-D Poisson's equation for the gate-dielectric, channel and buried-insulator regions. The validity of the model is confirmed by comparing with experimental data and other models. Using the model, the influences of gate-dielectric permittivity, buried-insulator permittivity, channel thickness, buried-insulator thickness and channel doping concentration on threshold behaviors are investigated. It is found that the threshold behaviors can be improved by using buried insulator with low permittivity, thin channel and high channel doping concentration. However, the threshold performance would be degraded when high-k gate dielectric is used due to enhanced fringing-field effect.     

Empirically Verified Thermodynamic Model of Gate Capacitance and Threshold Voltage of Nanoelectronic MOS Devices With Applications to HfO2 and ZrO2 Gate Insulators

A thermodynamic variational model derived by minimizing the Helmholtz free energy of the MOS device is presented. The model incorporates an anisotropic permittivity tensor and accommodates a correction for quantum-mechanical charge confinement at the dielectric/substrate interface. The energy associated with the fringe field that is adjacent to the oxide is of critical importance in the behavior of small devices. This feature is explicitly included in our model. The model is verified using empirical and technology-computer-aided-design-generated capacitance-voltage data obtained on MOS devices with ZrO₂, HfO₂, and SiO₂ gate insulators. The model includes considerations for an interfacial low-k interface layer between the silicon substrate and the high-k dielectric. This consideration enables the estimation of the equivalent oxide thickness. The significance of sidewall capacitance effects is apparent in our modeling of the threshold voltage (V_th) for MOS capacitors with effective channel length at 30 nm and below. In these devices, a variation in high-k permittivity produces large differences in V_th. This effect is also observed in the variance of V_th, due to dopant fluctuation under the gate.     

Modeling of cylindrical surrounding gate MOSFETs including the fringing field effects

A physically based analytical model for surface potential and threshold voltage including the fringing gate capacitances in cylindrical surround gate(CSG) MOSFETs has been developed.Based on this a subthreshold drain current model has also been derived.This model first computes the charge induced in the drain/source region due to the fringing capacitances and considers an effective charge distribution in the cylindrically extended source/drain region for the development of a simple and compact model.The fringing gate capacitances taken into account are outer fringe capacitance,inner fringe capacitance,overlap capacitance,and sidewall capacitance.The model has been verified with the data extracted from 3D TCAD simulations of CSG MOSFETs and was found to be working satisfactorily.     

Impact of geometry-dependent parasitic capacitances on the performance of CNFET circuits

Intrinsic carbon-nanotube field-effect transistors (CNFETs) have been shown to have superior performance over silicon transistors. In this letter, we provide an insight how the parasitic fringe capacitance in state-of-the-art CNFET geometries impacts the overall performance of CNFET circuits. We show that unless the device (gate) width can be significantly reduced, the effective gate capacitance of CNFET will be strongly dominated by the parasitic fringe capacitances, and the superior performance of intrinsic CNFET over silicon MOSFET cannot be achieved in circuit.     

Modeling of parasitic capacitances in deep submicrometer conventional and high-K dielectric MOS transistors

In deep submicrometer MOSFETs the device performance is limited by the parasitic capacitance and resistance. Hence a circuit model is needed to treat these effects correctly. In this work, we have developed circuit models for the parasitic capacitances in conventional and high-K gate dielectric MOS transistors by taking into account the presence of source/drain contact plugs. The accuracy of the model is tested by comparing the modeled results with the results obtained from three-dimensional (3-D) Monte-Carlo simulations and two-dimensional (2-D) device simulations over a wide range of channel length and oxide thickness. The model is also used to study the dependence of parasitic capacitance on gate length, gate electrode thickness, gate oxide thickness, gate dielectric constant, and spacer width.     

Device-Optimization Technique for Robust and Low-Power FinFET SRAM Design in NanoScale Era

In this paper, we propose a methodology to model and optimize FinFET devices for robust and low-power SRAMs. We propose to optimize the gate sidewall offset spacer thickness to simultaneously minimize leakage current and drain capacitance to on-current ratio in FinFET. With the source/drain extension doping controlled at the outer edges of the spacer, the thickness of the spacer determines the channel length. Optimization reduces the sensitivity of the device threshold voltage to the fluctuations in silicon thickness (by 32%) and gate length (by 73%). Our analysis shows that optimization of spacer thickness results in 65% reduction in SRAM cell leakage and improves cell read-failure probability (by 200 X) compared to conventional FinFET SRAM. Access time of an SRAM cell designed with optimized devices is comparable to conventional SRAM. We also compared the optimized-spacer-thickness SRAM cell with one designed using longer gate length and minimum-spacer-thickness transistors. The long-channel-device-based SRAM cell is marginally robust than optimized SRAM; however, increased gate-edge direct-tunneling leakage and parasitic capacitances degrade the power consumption and access time.     

High-performance poly-silicon TFTs using HfO/sub 2/ gate dielectric

High-performance low-temperature poly-Si thin-film transistors (TFTs) using high-/spl kappa/ (HfO/sub 2/) gate dielectric is demonstrated for the first time. Because of the high gate capacitance density and thin equivalent-oxide thickness contributed by the high-/spl kappa/ gate dielectric, excellent device performance can be achieved including high driving current, low subthreshold swing, low threshold voltage, and high ON/OFF current ratio. It should be noted that the ON-state current of high-/spl kappa/ gate-dielectric TFTs is almost five times higher than that of SiO/sub 2/ gate-dielectric TFTs. Moreover, superior threshold-voltage (V/sub th/) rolloff property is also demonstrated. All of these results suggest that high-/spl kappa/ gate dielectric is a good choice for high-performance TFTs.     

Influence of sidewall spacer on threshold voltage of MOSFET with high-k gate dielectric

In this paper, an analytical expression of the gate-dielectric fringing-potential distribution is derived for high-k gate-dielectric MOSFET through a conformal-mapping transformation method for the first time. Based on the fringing-potential distribution, the threshold-voltage model of the MOSFET is improved, and the influence of sidewall spacer on the threshold voltage is discussed in detail. Calculated results indicate that low-k sidewall spacer can alleviate the fringing-field effect.     

Engineering density of semiconductor-dielectric interface states to modulate threshold voltage in OFETs

Threshold-voltage control is critical to the further development of pentacene organic field-effect transistors (OFETs). In this paper, we demonstrate that the threshold voltage can be tuned through chemical treatment of the gate dielectric layer. We show that oxygen plasma treatment of an organic polymer gate dielectric, parylene, introduces traps at the semiconductor-dielectric interface that strongly affect the OFET performance. Atomic force microscopy, optical microscopy using crossed-polarizers, and current-voltage and capacitance-voltage characterization were performed on treated and untreated devices. A model is presented to account for the effects of trap-introduced charges, both 1) fixed charges (2.0/spl times/10/sup -6/ C/cm/sup 2/) that shift the threshold voltage from -17 to +116 V and 2) mobile charges (1.1/spl times/10/sup -6/ C/cm/sup 2/) that increase the parasitic bulk conductivity. This technique offers a potential method of tuning threshold voltage at the process level.     

14 nm FinFET栅围寄生电容的建模与拟合

提出了一种基于保角映射方法的14 nm鳍式场效应晶体管(FinFET)器件栅围寄生电容建模的方法。对FinFET器件按三维几何结构划分寄生电容的种类,再借助坐标变换推导出等效电容计算模型,准确表征了不同鳍宽、鳍高、栅高和层间介质材料等因素对寄生电容的依赖关系。为了验证该寄生电容模型的准确性,对不同结构参数的寄生电容进行三维TCAD仿真。结果表明,模型计算结果与仿真结果的拟合度好,准确地反映了器件结构与寄生电容之间的依赖关系。     

功率VDMOS器件的ESD瞬态模型

基于对功率VDMOS器件ESD保护及初始条件的分析,建立了VDMOS器件的ESD保护等效电路,分析了ESD响应过程,得到功率VDMOS器件的ESD瞬态模型. 分析结果表明,该模型准确地描述了功率VDMOS器件的ESD瞬态放电过程,解决了以往模型中初始条件分析不足等问题. 借助该模型,获得ESD器件的等效电阻和击穿电压、VDMOS的栅极输入电阻、栅源电容、栅氧厚度等与功率VDMOS器件抗ESD能力的关系,为功率VDMOS器件的抗ESD保护设计提供重要指导.     

High-performance poly-silicon TFTs incorporating LaAlO/sub 3/ as the gate dielectric

We have integrated a high-/spl kappa/ LaAlO/sub 3/ dielectric into low-temperature poly-Si (LTPS) thin-film transistors (TFTs). Good TFT performance was achieved-such as a high drive current, low threshold voltage and subthreshold slope, as well as an excellent on/off current ratio and high gate-dielectric breakdown field. This was achieved without hydrogen passivation or special crystallization steps. The good performance is related to the high gate capacitance density and small equivalent-oxide thickness provided by the high-/spl kappa/ dielectric.     

FinFET器件的集约阈电压模型

对FinFET器件(或称三栅MOSFET器件)的二维截面做了解析静电学分析以得出阈电压的计算公式.结果显示,由于三栅结构在高度方向的限制作用,需要引入一个H系数来修正栅电容,随着高度不断变大,它渐近于双栅MOSFET器件的情况.由该解析模型得出的电势分布与数值模拟结果吻合.提出了一个包含量子效应的Fin-FET器件的集约阈电压模型,结果表明,当高度或者顶栅的氧化层厚度变小时,栅电容及阈电压都会上升,这与FinFET设计时发现的趋势是相符合的.     

Compact Threshold Voltage Model for FinFETs

A 2D analytical electrostatics analysis for the cross-section of a FinFET (or tri-gate MOSFET) is performed to calculate the threshold voltage.The analysis results in a modified gate capacitance with a coefficient Ｈ introduced to model the effect of trigates and its asymptotic behavior in 2D is that for double-gate MOSFET.The potential profile obtained analytically at the cross-section agrees well with numerical simulations.A compact threshold voltage model for FinFET,comprising quantum mechanical effects,is then proposed.It is concluded that both gate capacitance and threshold voltage will increase with a decreased height,or a decreased gate-oxide thickness of the top gate，which is a trend in FinFET design.     

叠层片式陶瓷电感器寄生电容的提取

寄生电容是叠层片式电感器的重要参数,对电感器的Q值和谐振频率影响很大.如何准确估计寄生电容的大小成为电感器设计的一个难题.采用Ansoft Q3D软件建立了叠层片式陶瓷电感器的3D静电场有限元模型,计算了各电极间的杂散电容,然后建立电感器的等效电容网络,列出节点电压方程并求解得到寄生电容.计算结果和测量结果基本一致.瓷...     

A new quantitative model for weak inversion charge injection inMOSFET analog switches

This paper proposes a new model concerning the channel charges in weak inversion injected from a turn-off MOSFET into a holding capacitor. This portion of charge injection has recently been newly observed, showing a significant contribution to the switch-induced error voltage on the switched capacitor. Our model is derived at the critical point where the device is operated in the transition region between strong inversion and weak inversion. This point has been expressed explicitly as a function of the DC input voltage, the threshold voltage, and the fall time of the gate voltage. The ability of the model in accurately determining quantitatively the impact of the weak inversion charge injection on the error voltage has been extensively judged experimentally and by two-dimensional mixed-mode simulation for a wide variety of design parameters such as the channel width and length, the holding capacitance, the fall time of the gate voltage, and the DC input voltage The assumptions utilized in the model development have also been validated