Plasma charging damage on MOS devices with gate insulator ofhigh-dielectric constant material

Plasma charging effects on the gate insulator of high-dielectric constant (k) material in MOS devices deserve to be investigated because of different trap-assisted conduction mechanisms. Plasma-induced degradation in gate-leakage current and time to breakdown is clearly observed in this work. MOS device with Si₃N₄ film seems to have smaller degradation of gate-leakage current while it suffers shorter time to breakdown as compared to Ta₂O₅ samples. For devices with Ta₂O₅ film, a larger physical thickness suffers more reliability degradation from plasma charging damage because of the richer traps. Thus, a smaller physical thickness of high-k dielectric film is favorable for sub-micron MOS devices of ULSI application     

Leakage current comparison between ultra-thin Ta2O5 films and conventional gate dielectrics

Capacitors with ultra-thin (6.0-12.0 nm) CVD Ta₂O₅ film were fabricated on lightly doped Si substrates and their leakage current (I_g-V_g) and capacitance (C-V) characteristics were studied. For the first time, samples with stack equivalent oxide thickness around 2.0 nm were compared with ultra-thin silicon dioxide and silicon oxynitride. The Ta₂O₅ samples showed remarkably lower leakage current, which not only verified the advantages of ultra-thin Ta₂O₅ as dielectrics for high density DRAM's, but also suggested the possibility of its application as the gate dielectric material in MOSFET's     

Plasma-charging effects on submicron MOS devices

Plasma-charging damage on gate dielectrics of MOS devices is an important issue because of shrinking dimension, plasma nonuniformity, and effects on high-k gate dielectrics. A comprehensive study of plasma-charging effects on the electrical properties of MOS devices was investigated in this work. Shunt diodes were used to estimate the charging polarity distribution. For high-frequency application, the 1/f noise was found to be a promising index for assessing plasma-charging damage. Gate oxynitride formed by two-step nitridation was demonstrated to have better electrical reliability as compared to the conventional one-step nitridation, especially accompanied by amorphous silicon gate electrode. This improvement could be attributed to the relaxation of interface stress by amorphous silicon gate electrode and the suppression of hydrogen effects by gate oxynitride using two-step nitridation. Plasma-charging damage on Si₃N₄ and Ta₂O₅ gate dielectrics with high dielectric constant was also investigated. For MOS devices with Si₃N₄ film, the leakier characteristic and shorter time to breakdown reveal its inferior reliability. For MOS devices with Ta₂O₅ gate dielectric, the trap-assisted current mechanism makes a thicker physical thickness of Ta₂O₅ film more susceptible to plasma-charging-induced damage. Smaller physical thickness of Ta₂O₅ film in MOS devices is favorable due to the better reliability and comparable plasma-induced electrical degradation     

MOS transistors with stacked SiO2-Ta2O5-SiO2 gate dielectrics for giga-scale integration ofCMOS technologies

Advances in lithography and thinner SiO₂ gate oxides have enabled the scaling of MOS technologies to sub-0.25-μm feature size. High dielectric constant materials, such as Ta₂O₅ , have been suggested as a substitute for SiO₂ as the gate material beyond t_ox≈25 Å. However, the Si-Ta ₂O₅ material system suffers from unacceptable levels of bulk fixed charge, high density of interface trap states, and low silicon interface carrier mobility. In this paper we present a solution to these issues through a novel synthesis of a thermally grown SiO₂(10 Å)-Ta₂O₅ (MOCVD-50 Å)-SiO₂ (LPCVD-5 Å) stacked dielectric. Transistors fabricated using this stacked gate dielectric exhibit excellent subthreshold behaviour, saturation characteristics, and drive currents     

Transistor characteristics with Ta2O5 gatedielectric

As the gate oxide thickness decreases below 2 nm, the gate leakage current increases dramatically due to direct tunneling current. This large gate leakage current will be an obstacle to reducing gate oxide thickness for the high speed operation of future devices. A MOS transistor with Ta₂O₅ gate dielectric is fabricated and characterized as a possible replacement for MOS transistors with ultra-thin gate silicon dioxide. Mobility, I_d-V_d, I_d-V_g, gate leakage current, and capacitance-voltage (C-V) characteristics of Ta₂O₅ transistors are evaluated and compared with SiO₂ transistors. The gate leakage current is three to five orders smaller for Ta₂O₅ transistors than SiO₂ transistors     

Ta2O5/silicon barrier height measured fromMOSFETs fabricated with Ta2O5 gate dielectric

N-channel metal oxide semiconductor field effect transistors with Ta₂O₅ gate dielectric were fabricated. The Ta₂O₅/silicon barrier height was calculated using both the lucky electron model and the thermionic emission model. Based on the lucky electron model, a barrier height of 0.77 eV was extracted from the slope of the ln(I_g/I_d) versus ln(I_sub/I_d) plot using an impact ionization energy of 1.3 eV. Due to the low barrier height, the application of Ta₂ O₅ gate dielectric transistors is limited to low supply voltage preferably less than 2.0 V     

Design optimization of stacked layer dielectrics for minimum gate leakage currents

An effective model to evaluate the leakage currents for different stacked gates deep submicron MOS transistors is presented. For a given equivalent oxide thickness of a stacked gate, the gate leakage current decreases with an increase of high-k dielectric thickness or a decrease of interlayer thickness. Turning points at high gate biases of the I–V curves are observed for Si₃N₄/SiO₂, Ta₂O₅/SiO₂, Ta₂O₅/SiO_2−yN_y, Ta₂O₅/Si₃N₄, and TiO₂/SiO₂ stacked gates except for Al₂O₃/SiO₂ structure. Design optimization for the stacked gate architecture to obtain the minimum gate leakage current is evaluated.     

Fabrication and characterization of Si-MOSFET's with PECVDamorphous Ta2O5 gate insulator

Silicon MOS transistors having amorphous Ta₂O₅ insulator gates have been fabricated. The Ta₂O₅ films were deposited using a low pressure (a few mtorr) plasma-enhanced CVD process in a microwave (2.45 GHz) excited electron cyclotron resonance reactor. The source gas was TaF₅. Electrical characteristics of p-channel Al gate transistors are presented     

The observation of negative transconductance effect caused byreal-space-transfer of electrons in metal oxide semiconductor fieldeffect transistors fabricated with Ta2O5 gatedielectric

N-channel metal oxide semiconductor field effect transistors (MOSFETs) with Ta₂O₅ gate dielectric were fabricated. An intrinsic Ta₂O₅/silicon barrier height of 0.51 eV was extracted from the gate current. The effective Ta ₂O₅/silicon barrier height including image force barrier lowering is about 0.37 eV with drain to source voltage V_DS ranging from 1.5 V to 4.0 V. Due to the low barrier height, negative transconductance effect was observed in the linear region. The decrease of drain current is due to the real space transfer of electrons from the drain terminal to the gate electrode     

Dual Process Dielectric Formation for Decoupling Capacitors on Flexible Substrates

Large area, high density integrated capacitors within printed wiring boards can provide a substantial decoupling capacitance with very low parasitic inductance. Tantalum pentoxide (Ta₂O₅) is an excellent dielectric for this application due to the relatively high dielectric constant (~ 22-24), however the difficulty of fabricating large, defect-free capacitors has thus far prevented the realization of practical applications. This work demonstrates high performance capacitors with Ta₂O₅ dielectric developed with a two step oxidation scheme consisting of reactive sputtering followed by anodization. Thin films of Ta₂O₅ were deposited by reactive sputtering on silicon and also on Upilex^reg covered glass wafers using dc magnetron sputtering with a gas flow ratio of 10/90 O₂/Ar. In the two-step oxidation scheme, anodization is performed after reactively sputtering tantalum oxide films to obtain a densifled oxide structure. The electrical and physical properties of these two step sputtered/ anodized tantalum oxide films are shown to be superior to those of tantalum oxide films prepared by either anodization or sputtering alone. This work has shown that Ta₂O₅ is a potential dielectric for integrated capacitors that could be used in advanced packaging applications.     

Highly reliable, high-C DRAM storage capacitors with CVD TA2O5 films on rugged polysilicon

The authors report on a highly reliable stacked storage capacitor with ultrahigh capacitance using rapid-thermal-annealed low-pressure chemical vapor deposited (LPCVD) Ta₂O₅ films (~100 Å) deposited on NH₃-nitrided rugged poly-Si electrodes. Capacitances as high as 20.4 fF/μ² (corresponding to the thinnest t_ox.eff (16.9 Å) ever reported using LPCVD-Ta₂O₅ and poly-Si technologies) have been achieved with excellent leakage current and time-dependent dielectric breakdown (TDDB) characteristics. Extensive electrical characterization over a wide temperature range (~25-300°C) shows that Ta₂O ₅ films on rugged poly-Si electrodes have a better temperature stability in dielectric leakage and breakdown compared to the films on smooth poly-Si electrodes     

Promising storage capacitor structures with thin Ta2O5 film for low-power high-density DRAMs

To ensure the required capacitance for low-power DRAMs (dynamic RAMs) beyond 4 Mb, three kinds of capacitor structures are proposed: (a) poly-Si/SiO₂/Ta₂O₅/SiO₂ /poly-Si or poly-Si/Si₃N₄/Ta₂O ₅/SiO₂/poly-Si (SIS), (b) W/Ta₂O₅ /SiO₂/poly-Si (MIS), and (c) W/Ta₂O₅ W (MIM). The investigation of time-dependent dielectric breakdown and leakage current characteristics indicates that capacitor dielectrics that have equivalent SiO₂ thicknesses of 5, 4, and 3 nm can be applied to 3.3-V operated 16-Mb DRAMs having stacked capacitor cells (STCs) by using SIS, MIS, and MIM structures, respectively, and that 3 and 1.5 nm can be applied to 1.5-V operated 64-Mb DRAMs having STCs by using MIS and MIM structures, respectively. This can be accomplished while maintaining a low enough leakage current for favorable refresh characteristics. In addition, all these capacitors show good heat endurance at 950°C for 30 min. Therefore, these capacitors allow the fabrication of low-power high-density DRAMs beyond 4 Mb using conventional fabrication processes at temperatures up to 950°C. Use of the SIS structure confirms the compatability of the fabrication process of a storage capacitor using Ta₂O₅ film and the conventional DRAM fabrication processes by successful application to the fabrication process of an experimental memory array with 1.5-μm×3.6-μm stacked-capacitor DRAM cells     

Oxidized Ta2O5/Si3N4dielectric films on poly-crystalline Si for dRAMs

A dielectric film technology characterized by a novel multilayer structure formed by oxidation of Ta₂O₅/Si₃ N₄ films on polysilicon has been developed to realize high-density dRAMs. The dry oxidation of the Ta₂O₅/Si₃N₄ layers was performed at temperatures higher than 900°C. This film has a capacitance per unit area from 5.5 to 6.0 fF/ μm², which is equivalent to that of a 6.0- to 6.5-nm-thick SiO₂. The leakage current at an effective electric field of 5 MV/cm is less than 10^-9 A/cm². Under such an electric field, the extrapolated time to failure for 50% cumulative failure can be as high as 1000 years     

Effects of post-deposition annealing on the electrical propertiesand reliability of ultrathin chemical vapor deposited Ta2O5 films

This paper reports the effects of post-deposition rapid thermal annealing on the electrical characteristics of chemical vapor deposited (CVD) Ta₂O₅ (~10 nm) on NH₃-nitrided polycrystalline silicon (poly-Si) storage electrodes for stacked DRAM applications. Three different post-deposition annealing conditions are compared: a) 800°C rapid thermal O₂ annealing (RTO) for 20 sec followed by rapid thermal N₂ annealing (RTA) for 40 sec, b) 800°C RTO for 60 sec and c) 900°C RTO for 60 see. Results show that an increase in RTO temperature and time decreases leakage current at the cost of capacitance. However, over-reoxidation induces thicker oxynitride formation at the Ta₂O₅/poly-Si interface, resulting in the worst time-dependent dielectric breakdown (TDDB) characteristics     

High performance damascene metal gate MOSFETs for 0.1 μm regime

A novel transistor formation process (damascene gate process) was developed in order to apply metal gates and high dielectric constant gate insulators to MOSFET fabrication and minimize plasma damage to gate insulators. In this process, the gate insulators and gate electrodes are formed after ion implantation and high temperature annealing (~1000°C) for source/drain formation, and the gate electrodes are fabricated by chemical mechanical polishing (CMP) of gate materials deposited in grooves. Metal gates and high dielectric constant gate insulators are applicable to the MOSFET, since the processing temperature after gate formation can be reduced to as low as 450°C. Furthermore, process-damages on gate insulators are minimized because there is no plasma damage caused by source/drain ion implantation and gate reactive ion etching (RIE). By using this process, fully planarized metal (W/TiN or Al/TiN) gate transistors with SiO₂ or Ta₂O₅ as gate insulators were uniformly fabricated on an 8-in wafer. Further, the damascene metal gate transistors exhibited low gate sheet resistivity, no gate depletion and drastic improvement in gate oxide integrity, resulting in high transistor performance     

Fabrication and performance of selective HSG storage cells for 256Mb and 1 Gb DRAM applications

Fabrication of rapid thermal nitrided HSG transformed crown capacitor storage cells incorporating an ultrathin low pressure chemical vapor deposition (LPCVD) Ta₂O₅ and Si₃N ₄/SiO₂(NO) dielectric is proposed. 256 Mb array with HSG crown cells of 0.3 μm diameter×0.6 μm height and 49 A T_eff showed an area enhancement factor of 1.7 (relative to untransformed crown cell). C_min/C_max ratio of >0.95, and capacitance of 16.7 fF/cell is obtained. A measured leakage current density of 0.7 nA/cm² at 1.2 V is reported. Metal-oxide-semiconductor capacitor (MOSCAP) devices with HSG electrodes for 1 Gb application are characterized using capacitance-voltage (C-V) and current-voltage (I-V) analyses. Detailed HSG grain characterization results are presented with correlation to the electrical behavior of the devices. Devices are formed using LPCVD Ta₂O₅ and/or Si₃N₄ dielectric. HSG films formed from 4×10²⁰ atoms/cc phosphorus doped amorphous silicon show depletion in C-V behavior. It is shown that phosphine doping of HSG film is required to avoid depletion. Process selectivity of the UHV/CVD HSG transformation mechanism applied to thermal oxide and nitride field dielectrics is fully explored. Selectivity limits for different types of dielectric are also presented. Effect of critical parameters such as a-Si dopant concentration, HSG incubation time, anneal conditions, and a-Si layer thickness on HSG transformation are discussed for 1 Gb crown cells     

Leakage current reduction in chemical-vapor-depositedTa2O5 films by rapid thermal annealing in N2O

This study aims to improve the electrical characteristics and reliability of low-pressure chemical vapor deposited (LPCVD) Ta₂ O₅, films by developing a new post-deposition single-step annealing technique. Experimental results indicate that excited oxygen atoms generated by N₂O decomposition can effectively repair the oxygen vacancies in the as-deposited CVD Ta₂ O₅ film, thereby resulting in a remarkable reduction of the film's leakage current. Two other post-deposition annealing conditions are compared: rapid thermal O₂ annealing and furnace dry-O₂ annealing. The comparison reveals that RTN₂O annealing has the lowest leakage current, superior thermal stability of electrical characteristics and the best time-dependent dielectric breakdown (TDDB) reliability     

Fabrication and characterization of metal-oxide-semiconductorfield-effect transistors and gated diodes using Ta2O5 gate oxide

N-channel metal oxide semiconductor field effect transistors (MOSFETs) using Ta₂O₅, gate oxide were fabricated. The Ta₂O₅ films were deposited by plasma enhanced chemical vapor deposition. The I_DS-V_DS and I_DS-V_GS characteristics mere measured. The electron mobility was 333 cm²/V·s. The subthreshold swing was 73 mV/dec. The interface trapped charge density, the surface recombination velocity, and the minority carrier lifetime in the field-induced depletion region measured from gated diodes were 9.5×10¹² cm^-2 eV^-1, 780 cm/s and 3×10^-6 sec, respectively. A comparison with conventional MOSFETs using SiO₂ gate oxide was made     

Characterizing Fluorine-Ion Implant Effects on Poly-Si Thin-Film Transistors With ${hbox{Pr}}_{2}{hbox{O}}_{3}$ Gate Dielectric

The fluorine ion implantation applied to the polycrystalline silicon thin-film transistors (poly-Si TFTs) with high-k Pr₂O₃ as gate dielectric is investigated for the first time. Using the Pr₂O₃ gate dielectric can obtain a high gate capacitance density and thin equivalent-oxide thickness, exhibiting a greatly enhancement in the driving capability of TFT device. Introducing fluorine ions into the poly-Si film by fluorine ion implantation technique can effectively passivate the trap states in the poly-Si film and at the Pr₂O₃/poly-Si interface to improve the device electrical properties. The Pr₂O₃ TFTs fabricated on fluorine-implanted poly-Si film exhibit significantly improved electrical performances, including lower threshold voltage, steeper subthreshold swing, higher field-effect mobility, lower off-state leakage current, and higher on/off current ratio, as compared with the control poly-Si Pr₂O₃ TFTs. Also, the incorporation of fluorine ions also improves the reliability of poly-Si Pr₂O₃ TFTs against hot-carrier stressing, which is attributed to the formation of stronger Si-F bonds. Furthermore, superior threshold-voltage rolloff characteristic is also demonstrated in the fluorine-implanted poly-Si Pr₂O₃ TFTs. Therefore, the proposed scheme is a promising technology for high-performance and high-reliability solid-phase crystallized poly-Si TFT.     

Bi1.5Zn1.0 Nb1.5O7栅绝缘层的SiO2修饰对ZnO-TFTs性能的影响

具有高介电常数的栅绝缘层材料存在某种极化及耦合作用,使得ZnO-TFTs具有高的界面费米能级钉扎效应、大的电容耦合效应和低的载流子迁移率.为了解决这些问题,本文提出了一种使用SiO₂修饰的Bi_1.5Zn_1.0Nb_1.5O₇作为栅绝缘层的ZnO-TFTs结构,分析了SiO₂修饰对栅绝缘层和ZnO-TFTs性能的影响.结果表明,使用SiO₂修饰后,栅绝缘层和ZnO-TFTs的性能得到显著提高,使得ZnO-TFTs在下一代显示领域中具有非常广泛的应用前景.栅绝缘层的漏电流密度从4.5×10^-5A/cm²降低到7.7×10^-7A/cm²,粗糙度从4.52nm降低到3.74nm,ZnO-TFTs的亚阈值摆幅从10V/dec降低到2.81V/dec,界面态密度从8×10¹³cm^-2降低到9×10¹²cm^-2,迁移率从0.001cm²/（V·s）升高到0.159cm²/（V·s）.