Design of a Reflection-Type Phase Shifter With Wide Relative Phase Shift and Constant Insertion Loss

reflection-type phase shifter with constant insertion loss over a wide relative phase-shift range is presented. This important feature is attributed to the salient integration of an impedance-transforming quadrature coupler with equalized series-resonated varactors. The impedance-transforming quadrature coupler is used to increase the maximal relative phase shift for a given varactor with a limited capacitance range. When the phase is tuned, the typical large insertion-loss variation of the phase shifter due to the varactor parasitic effect is minimized by shunting the series-resonated varactor with a resistor R_p. A set of closed-form equations for predicting the relative phase shift, insertion loss, and insertion-loss variation with respect to the quadrature coupler and varactor parameters is derived. Three phase shifters were implemented with a silicon varactor of a restricted capacitance range of C_v,_min = 1.4 pF and C_v,_max = 8 pF, wherein the parasitic resistance is close to 2 Omega. The measured insertion-loss variation is 0.1 dB over the relative phase-shift tuning range of 237deg at 2 GHz and the return losses are better than 20 dB, excellently agreeing with the theoretical and simulated results.     

A Low-Loss Ku-Band Monolithic Analog Phase Shifter

A GaAs monolithic Ku-band analog phase shifter integrating 90° branch line coupler with planar varactor diodes has been fabricated for the first time. A phase shift of 109° +- 3° with an insertion loss of 1.8+-0.3 dB was measured from 16 to 18 GHz. A 360° phase shifter with 4.2+-0.9 dB insertion loss was realized in the same frequency range by connecting three phase-shifter chips in series. To our knowledge, this is the lowest insertion loss obtained by a 360° Ku-band phase shifter using monolithic circuits. In addition, hyperabrupt varactors using nonuniform doping profiles increased the phase shift by more than 30° and produced a more linear dependence of phase shift on control voltage.     

Linear tunable phase shifter using a left-handed transmission line

We demonstrate a compact, linear, and low loss variation hybrid phase shifter using a left-handed (LH) transmission line. For frequencies from 4.3 to 5.6 GHz, this phase shifter gives a nearly linear phase variation with voltage, with a maximum deviation of /spl plusmn/7.5/spl deg/. Within this frequency range, the maximum insertion loss is 3.6 dB, and the minimum insertion loss is 1.8 dB over a continuously adjustable phase range of more than 125/spl deg/, while minimum return loss is only 10.2 dB. Furthermore, this phase shifter requires only one control line, and it consumes almost no power.     

2.45-GHz CMOS Reflection-Type Phase-Shifter MMICs With Minimal Loss Variation Over Quadrants of Phase-Shift Range

CMOS reflection-type phase shifters with minimal insertion-loss variation over quadrants of phase-shift range are presented. Two performance enhancement techniques are proposed. First, the 3-dB quadrature hybrid is designed with a phase-compensated inductively coupled hybrid. Second, an impedance-transformed pi-resonated varactor network is presented to provide a full 360deg phase range, using a MOSFET varactor with limited reactance variation range. The design considerations and simulation are described. Two experimental 2.45-GHz phase shifters were implemented in 0.18-mum CMOS technology. One has a measured phase-shift range of 120deg with the insertion loss of 5.6 plusmn 1.2 dB in 2.33-2.60 GHz and the other has a phase range larger than 340deg with the insertion loss of 10.6 plusmn 2 dB in 2.44-2.55 GHz. Both chips are extremely compact with sizes of 0.72 and 0.66 mm², respectively, and consume zero dc power.     

A 4-bit CMOS Phase Shifter Using Distributed Active Switches

This paper presents a novel 4-bit phase shifter using distributed active switches in 0.18-mum RF CMOS technology. The relative phase shift, which varies from 0deg to 360deg in steps of 22.5deg, is achieved with a 3-bit distributed phase shifter and a 180deg high-pass/low-pass phase shifter. The distributed phase shifter is implemented using distributed active switches that consist of a periodic placement of series inductors and cascode transistors, thereby obtaining linear phase shift versus frequency with a digital control. The design guideline of the distributed phase shifter is presented. The 4-bit phase shifter achieves 3.5 plusmn 0.5 dB of gain, with an rms phase error of 2.6deg at a center frequency of 12.1 GHz. The input and output return losses are less than -15 dB at all conditions. The chip size is 1880 mum times 915 mum including the probing pads.     

A 3-dB Quadrature Coupler Using Broadside-Coupled Coplanar Waveguides

A 3-dB quadrature coupler which combines the advantages of broadside-coupling and coplanar waveguide structure suitable for a single-layer printed circuit board (PCB) circuit design is proposed. Compared to the recently published broadside-coupled structures, the proposed coupler can easily be realized in a single-layer substrate by using PCB manufacturing processes to eliminate the effects of uncertain factors from a multi-layer substrate. With the operation bandwidth ranging from 2.1 to 2.7 GHz, the measured return loss and isolation are all better than 19dB, and the insertion losses and relative phase difference between the direct and coupled ports are at 3.2 plusmn 0.1 dB and 90 plusmn 0.6deg, respectively. The dimension of the coupler is 2.1 cm times 1.9 cm.     

Improved broadband dumb-bell-shaped phase shifter using multi-section stubs

A broadband dumb-bell-shaped 45deg phase shifter is presented using a new design comprised of open-circuit and short-circuit multi-section stubs. A wideband phase shifter operating over the frequency range 2-6 GHz was designed and fabricated for verification purposes. It was measured to have a bandwidth of about 100% for a maximum phase deviation of plusmn3.2deg, and maximum insertion loss of 2.1 dB.     

New miniature 15-20-GHz continuous-phase/amplitude control MMICs using 0.18-/spl mu/m CMOS technology

The design and performance of two new miniature 360/spl deg/ continuous-phase-control monolithic microwave integrated circuits (MMICs) using the vector sum method are presented. Both are implemented using commercial 0.18-/spl mu/m CMOS process. The first phase shifter demonstrates all continuous phase and an insertion loss of 8 dB with a 37-dB dynamic range from 15 to 20 GHz. The chip size is 0.95 mm /spl times/ 0.76 mm. The second phase shifter can achieve all continuous phase and an insertion loss of 16.2 dB with a 38.8-dB dynamic range at the same frequency range. The chip size is 0.71 mm /spl times/ 0.82 mm. To the best of the authors' knowledge, these circuits are the first demonstration of microwave CMOS phase shifters using the vector sum method with the smallest chip size for all MMIC phase shifters with 360/spl deg/ phase-control range above 5 GHz reported to date.     

Development of multiband phase shifters in 180-nm RF CMOS technology with active loss compensation

We present the design and development of a novel integrated multiband phase shifter that has an embedded distributed amplifier for loss compensation in 0.18-/spl mu/m RF CMOS technology. The phase shifter achieves a measured 180/spl deg/ phase tuning range in a 2.4-GHz band and a measured 360/spl deg/ phase tuning range in both 3.5- and 5.8-GHz bands. The gain in the 2.4-GHz band varies from 0.14 to 6.6 dB during phase tuning. The insertion loss varies from -3.7 dB to 5.4-dB gain and -4.5 dB to 2.1-dB gain in the 3.5- and 5.8-GHz bands, respectively. The gain variation can be calibrated by adaptively tuning the bias condition of the embedded amplifier to yield a flat gain during phase tuning. The return loss is less than -10 dB at all conditions. The chip size is 1200 /spl mu/m/spl times/2300 /spl mu/m including pads.     

A Novel Miniature 1–22 GHz 90° MMIC Phase Shifter with Microstrip Radial Stubs

A novel miniature ultra wide bandwidth 90 monolithic microwave integrated circuit phase shifter with microstrip radial stubs operated from 1 to 22 GHz is presented. The phase shifter exhibits a high performance. Within the whole bandwidth from 1 to 22 GHz, the phase error of the phase shifter is less than 3deg, the return losses of the different phase shift states are more than 14 dB, the insertion loss of all phase shift states are within 3.3plusmn0.5 dB. The chip size of this phase shifter is 1.4 mm times 1.8 mm times 0.1 mm. The proposed phase shifter can be compatible with different polarity control signals without the need of drivers and can also be compatible with either analogue or digital control signals.     

一种S频段反射型可调模拟移相器的设计

设计了一种应用于S频段卫星通信相控阵系统的反射型可调模拟移相器。该移相器利用三分支线定向耦合器扩展了带宽,改善了工作频段内驻波;采用传输线和变容二极管构成的L型反射负载扩大了相移量。测试结果表明,在上行频段1.98～2.01 GHz内,相移量达到191°±1°,在下行频段2.17～2.2 GHz内,相移量达到186°±0.1°;插入损耗优于3.3 dB且插入损耗波动小于1 dB,回波损耗在整个电压调谐范围内均大于20 dB。该移相器结构简单、便于调节且价格低廉,在卫星通信领域有一定的应用价值。     

Compact reflective microstrip phase shifter for traveling wave antenna applications

A varactor diode based microstrip phase shifter for 5.8GHz is presented. It is designed for use in microstrip traveling wave antennas where there is a strict limitation on the available space for the phase shifters. To meet all requirements, a reflective type phase shifter is chosen. Such a phase shifter includes a hybrid coupler. A compact branch line coupler is designed to make the phase shifter fit between the radiating elements in the antenna, while maintaining sufficient electrical performance. Phase shifters are designed with different types of stubs connecting the diodes to ground. A phase tuning range of 62/spl deg/ is measured for a phase shifter with parallel open stubs, and 92/spl deg/ with shorted stubs. Insertion loss is in both cases less than 0.6dB. A complete five-element array antenna is built and characterized. Measurements show beam scanning angles within /spl plusmn/32/spl deg/ from broadside.     

A new MMIC broadside coupler using an array of air-bridges for directivity enhancement

A new quadrature broadside coupler is proposed, which employs an array of air-bridges to enhance directivity via its phase-equalization effect on the c-mode and /spl pi/-modes. The realization of air-bridges follows a standard MMIC fabrication process. An experimental chip fabricated on the 75-/spl mu/m GaAs substrate verifies the air-bridge effect and shows wideband characteristics of the coupling of 3.2/spl plusmn/0.4 dB, the insertion loss of 3.9/spl plusmn/0.4 dB, the output phase deviation from quadrature less than 6/spl deg/, and the isolation greater than 18 dB from 20 to 40 GHz.     

Design and performance of a new digital phase shifter at X-band

A new digital phase shifter design at X-band is presented. The phase shifter operates based on converting a microstrip line to a rectangular waveguide and thus achieving the phase shift by changing the wave propagation constant through the medium. As a proof of principle, a 3-b phase shifter has been designed and constructed using PIN diode switches. An average insertion loss of 1.95 dB and phase shift error of less than 4/spl deg/ at 10.6 GHz are achieved.     

2.4 GHz continuously variable ferroelectric phase shifters using all-pass networks

Continuously variable ferroelectric (BST on sapphire) phase shifters based on all-pass networks are presented. An all-pass network phase shifter consists of only lumped LC elements, and thus the total size of the phase shifter is kept to less than 2.2 mm /spl times/ 2.6 mm at 2.4 GHz. The tunability (C/sub max//C/sub min/) of a BST interdigital capacitor is over 2.9 with a bias voltage of 140 V. The phase shifter provides more than 121/spl deg/ phase shift with the maximum insertion loss of 1.8 dB and the worst case return loss of 12.5 dB from 2.4 GHz to 2.5 GHz. By cascading two identical phase shifters, more than 255/spl deg/ phase shift is obtained with the maximum insertion loss of 3.75 dB. The loss figure-of-merit of both the single- and double-section phase shifters is over 65/spl deg//dB from 2.4 GHz to 2.5 GHz.     

A PCB-compatible 3-dB coupler using microstrip-to-CPW via-hole transitions

A 3-dB coupler by implementing microstrip-to-coplanar waveguide (CPW) via-hole transitions is proposed. The proposed coupler, with the advantages of wider coupled line widths and spacing without using any bonding wires, can eliminate the uncertain factors of conventional Lange couplers caused by the printed circuit board (PCB) manufacturing processes. The proposed coupler can be easily fabricated on a single-layer PCB substrate instead of using multilayer substrates. Good agreements between the simulation and the measurement in the frequency range from 0.45 to 5 GHz can be achieved. The measured results at the center frequency of 2.4 GHz have the return loss better than -15dB; the insertion loss of coupled and direct ports is about 3/spl plusmn/ 0.2dB and the relative phase difference of 89/spl plusmn/0.3/spl deg/. The dimension of the coupler is 3.1cm /spl times/ 1.8cm.     

On the feasibility of CMOS multiband phase shifters for multiple-antenna transmitters

We present the design of an integrated multiband phase shifter in RF CMOS technology for phased array transmitters. The phase shifter has an embedded classical distributed amplifier for loss compensation. The phase shifter achieves a more than 180/spl deg/ phase tuning range in a 2.4-GHz band and a measured more than 360/spl deg/ phase tuning range in both 3.5-GHz and 5.8-GHz bands. The return loss is less than -10dB at all conditions. The feasibility for transmitter applications is verified through measurements. The output power at a 1-dB compression point (P/sub 1 dB/) is as high as 0.4dBmat 2.4GHz. The relative phase deviation around P/sub 1 dB/ is less than 3/spl deg/. The design is implemented in 0.18-/spl mu/mRF CMOS technology, and the chip size is 1200/spl mu/m /spl times/ 2300 /spl mu/m including pads.     

A scalable reflection type phase shifter with large phase variation

We describe a reflection type phase shifter which exhibits a large phase shift range. We characterized its response between 1.95 GHz and 2.15 GHz and achieved over 400/spl deg/ phase shift with less than 4dB insertion loss. The transition time from 0/spl deg/ to 180/spl deg/ is <20 nS. Our design is scalable to mm-wave operation because it uses no inductors.     

宽频带L波段360°模拟信号移相器的设计

该文介绍了宽频带360°模拟移相器的设计理论。针对移相器的线性调相、平衡插入损耗波动、宽频带等进行了详细的探讨,且推导出确定移相器频带宽度的目标函数。用CAD方法迅速而准确地优化各网络设计参量。采用微波集成电路工艺制作的L波段模拟移相器在1.3～2.1GHz范围内可获得360°连续可变相移,最大调相电压18V,中心频率线性度优于±2.5％,插入损耗波动小于3dB。综合性能均优于国内报道的移相器。     

A 2-bit miniature X-band MEMS phase shifter

The design and performance of a compact low-loss X-band true-time-delay (TTD) MEMS phase shifter fabricated on 8-mil GaAs substrate is described. A semi-lumped approach using microstrip transmission lines and metal-insulator-metal (MIM) capacitors is employed for the delay lines in order to both reduce circuit size as well as avoid the high insertion loss found in typical miniaturized designs. The 2-bit phase shifter achieved an average insertion loss of -0.70 dB at 9.45 GHz, and an associated phase accuracy of /spl plusmn/1.3/spl deg/. It occupies an area of only 5 mm/sup 2/, which is 44% the area of the smallest known X-band MEMS phase shifter . The phase shifter operates over 6-14 GHz with a return loss of better than -14 dB.