首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到17条相似文献,搜索用时 187 毫秒
1.
为了增强超高分子量聚乙烯(UHMWPE)纤维与橡胶基体之间的界面粘结强度,采用高锰酸钾溶液对UHMWPE纤维进行表面处理,并将处理后的纤维加入到天然橡胶中制备短切UHMWPE纤维/橡胶复合材料。结果表明,高锰酸钾溶液处理可有效增加纤维表面粗糙度及表面含氧官能团含量,最佳改性工艺条件是:按照m(高锰酸钾)∶m(浓硝酸)=1∶30配置高锰酸钾溶液,在室温下将UHMWPE纤维放入上述溶液中处理1 min。与纯橡胶样品相比,在m(UHMWPE纤维)∶m(天然橡胶)=0~6∶100范围内,随着处理后短纤维质量分数的增加,复合材料的硬度不断增大,最大增加量达到94%;复合材料的撕裂强度先增大后减小,在m(UHMWPE纤维)∶m(天然橡胶)=4∶100时达到最大值,最大增加量达到43%。  相似文献   

2.
为提高超高分子质量聚乙烯(UHMWPE)纤维复合材料中纤维与树脂基体之间的界面黏结强度,提出通过不同质量分数的硅烷偶联剂KH-570处理纳米SiO_2对UHMWPE纤维进行表面改性。对改性处理后的纤维与乙烯基酯树脂进行黏结强度试验,发现硅烷偶联剂处理纳米SiO_2能有效提高纤维的界面黏结强度,同时使纤维保持一定的断裂强度。  相似文献   

3.
低温等离子体对UHMWPE纤维的表面改性   总被引:1,自引:0,他引:1  
运用自行研制的常压低温等离子体设备对超高相对分子质量聚乙烯(UHMWPE)纤维进行了表面处理,选用正交试验法通过润湿性测试优化出不同工作气氛下的工艺条件,采用强力测试、扫描电镜(SEM)和光电子能谱仪(XPS)分析了等离子体处理前后UHMWPE纤维的性能变化。结果表明,常压低温等离子体在Ar携带丙烯酸和Ar/O2的气氛下处理UHMWPE纤维,表面改性效果良好。特别是选用Ar/O2流量比100:1,处理速度为5.8 m/min,输出功率189 W,可满足连续化生产。  相似文献   

4.
以硅烷偶联剂KH-550在不同条件下处理超高相对分子质量聚乙烯(UHMWPE)纤维,采用正交实验方法,以硅烷偶联剂KH-550的浓度(A)、处理温度(B)、处理时间(C)为因素,以UHMWPE纤维的断裂强力、界面剪切强度(τ)为实验指标,研究了硅烷偶联剂KH-550处理UHMWPE纤维的最佳工艺条件。结果表明:UHMWPE纤维断裂强力的影响因素主次顺序为A,B,C,τ的影响因素主次顺序为B,A,C;硅烷偶联剂KH-550处理UHMWPE纤维的最优工艺为硅烷偶联剂KH-550质量分数17.5%,处理温度55℃,处理时间7 h,在此条件下得到的UHMWPE纤维的断裂强力为41.15 cN,断裂强力损失率为2.44%,τ为1.359MPa,τ的增加率为35.22%。  相似文献   

5.
介绍了低温等离子体的概念、分类及其在超高相对分子质量聚乙烯纤维(UHMWP E)表面改性方面的特点;阐述了国内外在低温等离子体对UHMWPE纤维表面改性前后纤维本身及其复合材料性能的影响情况;简介了用自行研制的低温等离子体设备对UHMWPE纤维进行表面改性的研究结果和低温等离子体处理UHMWPE纤维表面改性的发展前景。实验表明,UHMWPE纤维经过等离子体处理后表面产生刻蚀和交联,其与树脂间的粘结性能改善;该低温等离子体设备能满足UHMWPE纤维表面改性连续化生产需要。  相似文献   

6.
采用紫外辐射接枝方法对超高相对分子质量聚乙烯(UHMWPE)纤维表面进行改性。探讨了单体种类及浓度、引发剂、抗氧剂、接枝方法等对UHMWPE纤维表面处理效果的影响,测试了以其作为增强材料的复合材料的层间剪切强度。结果表明:在有氧开放体系下,气相接枝效果好于液相接枝;丙烯酰胺单体的接枝效果优于其它单体;接枝率随接枝单体浓度和接枝时间的增加而增加。采用丙烯酰胺为接枝单体,在光强度为86μW/cm~2条件下,对UHMWPE纤维进行紫外辐射接枝改性,按照一定铺层方式制备的环氧基复合材料的层间剪切强度从未处理的14.59MPa提高到17.36MPa。  相似文献   

7.
利用低温等离子体技术对超高相对分子质量聚乙烯(UHMWPE)纤维进行表面改性,用单因素试验和正交试验对改性后的UHMWPE纤维的静摩擦因数和断裂强力进行测试与分析,最终确定最优的等离子体改性工艺为压强50 Pa、功率100 W、时间180 s。对处理前后的UHMWPE纤维的毛细效应、表面形貌、红外光谱进行了测试和对比,结果发现:改性后的UHMWPE纤维的吸水性能明显增强,纤维表面变得凹凸不平,粗糙度和比表面积增大,纤维表面起伏数量增多,幅度变大,且出现了新的含氧官能团,有利于提高UHMWPE纤维表面的黏结性。  相似文献   

8.
选用硅烷偶联剂KH-550,KH-560和钛酸酯偶联剂NDZ-201作为表面改性剂,对超高相对分子质量聚乙烯(UHMWPE)冻胶纤维在萃取阶段进行表面处理,经干燥、超拉伸制得表面改性UHMWPE纤维。采用红外光谱仪、接触角测量仪测定了纤维的表面化学结构和表面润湿性能,采用单纤维树脂包埋-拔出法测定了纤维与树脂基体的界面剪切强度,比较了改性前后纤维的力学性能变化。结果表明:改性后纤维表面引入了极性基团,硅烷偶联剂KH-550对UHMWPE纤维的表面改性效果最好。采用质量分数为1%的硅烷偶联剂KH-550溶液处理后,纤维与环氧树脂间的界面剪切强度提高了87.8%,纤维的断裂强度和模量分别提高了6.9%和32.6%。  相似文献   

9.
利用自行研制的铬酸处理液对超高相对分子质量聚乙烯(UHMWPE)纤维进行表面改性,并利用扫描电镜(SEM)、红外光谱(FITR)和接触角、单丝强力试验对纤维的表面性能和强度的变化进行表征。结果表明,表面处理时间和表面处理温度是影响纤维处理后性能的重要因素,UHMWPE纤维的最佳表面处理时间为3mim,最佳表面处理温度为80~85℃。  相似文献   

10.
以过氧化二苯甲酰对超高相对分子质量聚乙烯(UHMWPE)进行表面处理,采用傅里叶变换红外光谱、差示扫描量热仪和热重分析仪进行了表征,并用扫描电镜观察了微观形貌,制备了天然橡胶(NR)/UHMWPE复合材料,研究了改性UHMWPE对NR硫化特性、力学性能及动态力学性能的影响。结果表明,改性后的UHMWPE表面粗糙度增加,熔融温度升高;NR/UHMWPE复合材料的最佳硫化条件为140℃、20 min。随着改性UHMWPE用量的增加,NR/UHMWPE复合材料的邵尔A硬度逐渐增大,拉伸强度逐渐减小。改性UHMWPE与NR基体黏结性较好,改善了复合材料的力学性能和动态力学性能。  相似文献   

11.
本文采用不同浓度和温度下的铬酸溶液对超高分子量聚乙烯纤维进行表面处理。通过DSC、DMA、X-衍射和SEM分析纤维的结构,测试了纤维接触角、断裂强度和层间剪切强度。实验结果表明,随着处理液酸浓度的增加,纤维表面刻蚀程度增加,层间剪切强度增大,而纤维表面极性不变;处理时间和溶液温度须控制在一个合适的水平。  相似文献   

12.
《Polymer Composites》2017,38(6):1215-1220
The mechanical properties of ultra‐high molecular weight polyethylene (UHMWPE) fibers reinforced natural rubber (NR) composites were determined, and the effects of fiber surface treatment and fiber mass fraction on the mechanical properties of the composites were investigated. Chromic acid was used to modify the UHMWPE fibers, and the results showed that the surface roughness and the oxygen‐containing groups on the surface of the fibers could be effectively increased. The NR matrix composites were prepared with as‐received and chromic acid treated UHMWPE fibers added 0–6 wt%. The treated UHMWPE fibers increased the elongation at break, tear strength, and hardness of the NR composites, especially the tensile stress at a given elongation, but reduced the tensile strength. The elongation at break increased markedly with increasing fiber mass fraction, attained maximum values at 3.0 wt%, and then decreased. The tear strength and hardness exhibited continuous increase with increasing the fiber content. Several microfibrillations between the fiber and NR matrix were observed from SEM images of the fractured surfaces of the treated UHMWPE fibers/NR composites, which meant that the interfacial adhesion strength was improved. POLYM. COMPOS., 38:1215–1220, 2017. © 2015 Society of Plastics Engineers  相似文献   

13.
采用铬酸刻蚀和化学气相沉积聚吡咯处理了超高相对分子质量聚乙烯(UHMWPE)纤维。用DSC、DMA、X-射线衍射及SEM分析了纤维的热力学性能、结晶情况及纤维的表观形貌。结果表明,铬酸处理及化学气相沉积聚吡咯处理后,纤维的耐热性均有所提高,纤维表面变得更加粗糙,其中化学气相沉积聚吡咯处理的纤维变化更明显。  相似文献   

14.
PE—UHMW纤维/环氧树脂复合材料研究   总被引:1,自引:0,他引:1  
对超高相对分子质量聚乙烯(PE-UHMW)纤维进行了铬酸液相氧化和纳米二氧化硅溶胶表面涂覆的复合化表面处理,并对PE-UHMW纤维/环氧树脂复合材料进行了界面性能研究。结果表明,单纯的液相氧化和表面涂覆均可以提高复合材料的界面性能,但液相氧化处理时间过长会使纤维强度降低,而复合化处理则具有协同效应,可以不降低纤维强度而大幅度提高复合材料的层间剪切强度,是一种有效的表面处理方法。  相似文献   

15.
Graft copolymerization of methyl methacrylate monomer onto ultra high molecular weight polyethylene (UHMWPE) and acid‐etched UHMWPE was conducted using preirradiation method in air in the presence of a Mohr salt and sulfuric acid to improve adhesion to the bone cement. The grafted samples were characterized by Fourier transform infrared (FTIR) spectroscopy, gravimetric method, goniometry, and interfacial bonding strength measurements. The FTIR results showed the presence of ether, carbonyl, and hydroxyl groups for grafted films. The gravimetric results showed that the chromic acid etching and graft copolymerization had a synergetic effect so, the irradiated, then chromic acid etched at room temperature and grafted sample (Rad etch25) had the highest grafting degree. The interfacial bonding strength between UHMWPE and poly methyl methacrylate bone cement was considerably improved by graft copolymerization and chromic acid etching. The surface morphology was studied by scanning electron microscopy. The substitution of polar groups into the backbone of UHMWPE by chromic acid etching and graft copolymerization changed its contact angles with water and methylene iodide and increased its surface energy, as evidenced by contact angle measurements. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008  相似文献   

16.
The grafting of methyl methacrylate (MMA) onto ultra‐high‐molecular‐weight polyethylene (UHMWPE) and chromic acid etched UHMWPE was conducted with a preirradiation method in air in the presence of a Mohr salt and sulfuric acid. The grafted samples were characterized by Fourier transform infrared (FTIR) spectroscopy, a gravimetric method, differential scanning calorimetry, scanning electron microscopy (SEM), and interfacial bonding strength measurements. The FTIR results showed the presence of ether and carbonyl groups in the MMA‐grafted UHMWPE (MMA‐g‐UHMWPE) samples. The Taguchi experimental design method was used to find the best degree of grafting (DG) and bonding strength. The efficient levels for different variables were calculated with an analysis of variance of the results. SEM micrographs of MMA‐g‐UHMWPE samples showed that with increasing DG and chromic acid etching, the MMA‐g‐UHMWPE rich phase increased on the surface; this confirmed the high interfacial bonding strength of the grafted samples with bone cement. The grafting of the MMA units onto UHMWPE resulted in a lower crystallinity, and the crystallization process proceeded at a higher rate for the MMA‐g‐UHMWPE samples compared to the initial UHMWPE; this suggested that the MMA grafted units acted as nucleating agents for the crystallization of UHMWPE. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010  相似文献   

17.
UHMWPE fiber exhibits high performance, featuring high tensile strength and modulus, because of its extended chain structure. However, this fiber demonstrates some defects, such as low melting point, creep, and poor interfacial bonding with resin. Therefore, it is still not widely applied in composites. This research attempted to improve the performance by applying interfacial treatment to the fiber, using polypyrrole (PPy) synthesized through oxidation. The interfacial shear strength was evaluated using the results of a pull-out test and a Zeta Potential. The UHMWPE fiber was exposed to PPy treatment at various temperatures. The PPy-modified fiber was then impregnated with epoxy to generate the composites. The effects of the modification were also examined. The performance of the composites was determined by the Zeta Potentials of the fiber and resin, using an EKA electrokinetic analyzer. The interfacial shear strength was determined by the pull-out test. The morphology of fiber was observed by SEM. Results show that the shear strength of the interface between the PPy-treated UHMWPE fiber and epoxy increased 215%. The correlation between the Zeta Potential and the interfacial shear strength was also observed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号