A Novel Magnetodielectric Solid Solution Ceramic 0.4LiFe5O8–0.6Li2MgTi3O8 with Excellent Microwave Dielectric Properties

In this study, a novel spinel solid solution ceramic of 0.4LiFe₅O₈–0.6Li₂MgTi₃O₈ (0.4LFO–0.6LMT) has been developed and investigated. It is found that the 40 mol% LiFe₅O₈ and 60 mol% Li₂MgTi₃O₈ are fully soluble in each other and a disordered spinel phase is formed. The ceramic sample sintered at 1050°C/2 h exhibits both good magnetic and dielectric properties in the frequency range 1–10 MHz, with a permeability between 29.9~14.1 and magnetic loss tangent between 0.12~0.67, permittivity between 16.92~16.94 and dielectric loss tangent between 5.9 × 10^?3–2.3 × 10^?2. The sample also has good microwave dielectric properties with a relative permittivity of 16.1, a high quality factor (Q × f) ~28 500 GHz (at 7.8 GHz). Furthermore, 3 wt% H₃BO₃–CuO (BCu) addition can effectively lower the sintering temperature to 925°C and does not degrade the magnetodielectric properties. The chemical compatibility with silver electrode indicates that this kind of ceramics is a good candidate for the low‐temperature cofired ceramic (LTCC) application.     

Silver Co‐Firable Li2ZnTi3O8 Microwave Dielectric Ceramics with LZB Glass Additive and TiO2 Dopant

New dielectric ceramics are prepared by the conventional solid‐state ceramic route. Effects of LZB glass on sintering, phase purity, microstructure, and dielectric properties of Li₂ZnTi₃O₈ ceramics have been investigated. Adding LZB lowers sintering temperature from 1050°C to 875°C, and does not induce much degradation of dielectric properties. The 1.0 wt% LZB glass‐added ceramic has better properties of ε_r = 23.9, Q × f = 31,608 GHz, τ_f = ?14.3 ppm/°C. Additions of TiO₂ markedly improve microwave properties. Typically, the Li₂ZnTi₃O₈ + 1 wt%LZB + 3.5 wt%TiO₂ sintered at 900°C shows ε_r = 26.1, Q × f = 45,168 GHz, τ_f = ?4.1 ppm/°C. Compatibility with Ag electrode indicates that this material may be applied to LTCC devices.     

Low‐Temperature Sintering and Microwave Dielectric Properties of CaMoO4‐Based Temperature Stable LTCC Material

The CaMoO₄–xY₂O₃–xLi₂O ceramics were prepared by the solid‐state reaction method. The sintering behavior, phase evolution, microstructure, and microwave dielectric properties were investigated. CaMoO₄ solid solution was obtained when x = 0.030, and two‐phase system including tetragonal CaMoO₄ phase and cubic Y₂O₃ phase formed when 0.066 ≤ x ≤ 1.417. A temperature stable CaMoO₄‐based microwave dielectric ceramic with ultralow sintering temperature (775°C) was obtained in the CaMoO₄–xY₂O₃–xLi₂O system when x = 0.306, which showed good microwave dielectric properties with a low permittivity of 9.5, a high Q_f value of 63 240 GHz, and a near‐zero temperature coefficient of resonant frequency of +7.2 ppm/°C.     

Low‐Temperature Sintering Li2MoO4/Ni0.5Zn0.5Fe2O4 Magneto‐Dielectric Composites for High‐Frequency Application

The coexistence of Li₂MoO₄ (LMO) and Ni_0.5Zn_0.5Fe₂O₄ (NZO) has been proven and their low‐temperature‐sintered magneto‐dielectric composites (1?x)LMO–xNZO (volume fraction factor x = 0.1, 0.3, 0.5, 0.7) were prepared by the conventional solid‐state reaction method and were sintered below 700°C. It is found that the optimal sample (x = 0.5) has good and relatively stable magneto‐dielectric performance in the frequency range from 10 MHz to 1 GHz with permittivity between 7.14 and 6.84, dielectric loss tangent between 0.09 and 0.02, and permeability between 5.23 and 3.30, magnetic loss tangent between 0.06 and 0.65, respectively. Furthermore, the verified chemical compatibility with silver indicates that the LMO–NZO ceramics are potential for low‐temperature cofired ceramic application and their multifunctional magneto‐dielectric properties also make them for potential applications in electronic devices.     

Liquid‐phase sintering,microstructural evolution,and microwave dielectric properties of Li2Mg3SnO6–LiF ceramics

The liquid‐phase sintering behavior and microstructural evolution of x wt% LiF aided Li₂Mg₃SnO₆ ceramics (x = 1‐7) were investigated for the purpose to prepare dense phase‐pure ceramic samples. The grain and pore morphology, density variation, and phase structures were especially correlated with the subsequent microwave dielectric properties. The experimental results demonstrate a typical liquid‐phase sintering in LiF–Li₂Mg₃SnO₆ ceramics, in which LiF proves to be an effective sintering aid for the Li₂Mg₃SnO₆ ceramic and obviously reduces its optimum sintering temperature from ~1200°C to ~850°C. The actual sample density and microstructure (grain and pores) strongly depended on both the amount of LiF additive and the sintering temperature. Higher sintering temperature tended to cause the formation of closed pores in Li₂Mg₃SnO₆‐x wt% LiF ceramics owing to the increase in the migration ability of grain boundary. An obvious transition of fracture modes from transgranular to intergranular ones was observed approximately at x = 4. A single‐phase dense Li₂Mg₃SnO₆ ceramic could be obtained in the temperature range of 875°C‐1100°C, beyond which the secondary phase Li₄MgSn₂O₇ (<850°C) and Mg₂SnO₄ (>1100°C) appeared. Excellent microwave dielectric properties of Q × f = 230 000‐330 000 GHz, ε_r = ~10.5 and τ_f = ~?40 ppm/°C were obtained for Li₂Mg₃SnO₆ ceramics with x = 2‐5 as sintered at ~1150°C. For LTCC applications, a desirable Q × f value of ~133 000 GHz could be achieved in samples with x = 3‐4 as sintered at 875°C.     

Enhanced Piezoelectric Properties of (Ba1−xCax)(Ti0.92Sn0.08)O3 Lead‐Free Ceramics

(Ba_1?xCa_x)(Ti_0.92Sn_0.08)O₃ (x = 0.00–0.06 mol) ceramics with a high relative density over 96% were prepared by a conventional sintering method at 1480°C. At room temperature, a polymorphic phase transition from orthorhombic phase to tetragonal phase was confirmed by the XRD patterns in the composition range of 0.04 ≤ x ≤ 0.06. A high piezoelectric coefficient d₃₃ up to 568 pC/N was obtained at x = 0.05 mol, which is higher than the other component of (Ba,Ca)(Ti,Sn)O₃ system. At the same time, the corresponding planar electromechanical coupling factor k_p, converse piezoelectric coefficient dS/dE, and dielectric constant ε_r reach 47.7%, 1013 pm/V, and 23000, respectively. These results indicate that the (Ba,Ca)(Ti,Sn)O₃ ceramics are a promising candidate to replace for the lead‐based piezoelectric materials.     

Effects of ZnO and B2O3 on the Microstructure and Microwave Dielectric Properties of 5Li2O‐1Nb2O5‐5TiO2 Ceramics

The effects of ZnO and B₂O₃ addition on the sintering behavior, microstructure, and the microwave dielectric properties of 5Li₂O‐1Nb₂O₅‐5TiO₂ (LNT) ceramics have been investigated. With addition of low‐level doping of ZnO and B₂O₃, the sintering temperature of the LNT ceramics can be lowered down to near 920°C due to the liquid phase effect. The Li₂TiO₃ss and the “M‐phase” are the two main phases, whereas other phase could be observed when co‐doping with ZnO and B₂O₃ in the ceramics. And the amount of the other phase increases with the ZnO content increasing. The addition of ZnO does not induce much degradation in the microwave dielectric properties but lowers the τ_f value to near zero. Typically, the good microwave dielectric properties of ε_r = 36.4, Q × f = 8835 GHz, τ_f = 4.4 ppm/°C could be obtained for the 1 wt% B₂O₃ and 4 wt% ZnO co‐doped sample sintered at 920°C, which is promising for application of the multilayer microwave devices using Ag as internal electrode.     

Structure and microwave dielectric properties of the Li2/3(1−x)Sn1/3(1−x)MgxO systems (x = 0‐4/7)

In this paper, the Li_2/3(1?x)Sn_1/3(1?x)Mg_xO (LSMxO) ceramic systems were prepared by solid‐state reaction using novel atmosphere‐controlled sintering (x = 0‐4/7). Pure Li₂SnO₃ was observed for x = 0, the Li₂Mg₃SnO₆ and Li₂SnO₃ coexisted for x = 1/7, and the coexistence of three kinds of phases was detected for x = 1/5 and 1/4, including Li₄MgSn₂O₇ impurity phase. Pure Li₂Mg₃SnO₆‐like phase with cubic rock salt structure in Fm‐3m space group was obtained in the range of 1/3‐4/7. All samples showed well‐dense and smooth microstructures. The microwave dielectric properties highly depended on the phase composition, bond valence, FWHM of Raman spectrum, Raman shift, average grain sizes, and octahedral distortion. The LSMxO ceramics sintered at 1250°C for 5 hours possessed excellent comprehensive properties of ε_r = 15.43, Q×f = 80 902 GHz and τ_f = +5.61 ppm/°C for x = 1/7. Typically, the LSMxO ceramics sintered at 1350°C for 5 hours showed a maximum Q × f of 168 330 GHz for x = 1/2.     

Structure Evolution and Enhanced Microwave Dielectric Characteristics of (Sr1−xCax)La2Al2O7 Ceramics

(Sr_1?xCa_x)La₂Al₂O₇ (0.1 ≤ x ≤ 0.5) ceramics were prepared by a standard solid‐state reaction method. Their densification behavior and microwave dielectric properties were investigated together with the structural evolution. X‐ray diffraction analysis indicated that the major phase of Ruddlesden–Popper structure with n = 2 was obtained for all the compositions investigated here. Partial Ca substitution improved the sintering behavior of SrLa₂Al₂O₇ ceramics. More importantly, microwave dielectric characteristics were enhanced in (Sr_1?xCa_x)La₂Al₂O₇ ceramics with compositions of x = 0.1~0.3. The stacking fault was confirmed by TEM observation in the present ceramics, and the microwave dielectric loss was influenced by it. The best combination of microwave dielectric characteristics was achieved for the composition of x = 0.1: ε_r = 19.9, Qf = 135 400 GHz and τ_f = ?18.5 ppm/°C.     

Dielectric Properties of Ba0.8Ca0.2TiO3–Bi(Mg0.5,Ti0.5)O3–NaNbO3 Ceramics

Ceramics in the system 0.45Ba_0.8Ca_0.2TiO₃–(0.55?x)Bi(Mg_0.5Ti_0.5)O₃–xNaNbO₃, x = 0–0.02 were fabricated by a conventional solid‐state reaction route. X‐ray powder diffraction indicated cubic or pseudocubic symmetry for all samples. The parent 0.45Ba_0.8Ca_0.2TiO₃–0.55Bi(Mg_0.5Ti_0.5)O₃ composition is a relaxor dielectric with a near‐stable temperature coefficient of relative permittivity, ε_r = 950 ± 10% across the temperature range 80°C–600°C. Incorporation of NaNbO₃ at x = 0.2 extends the lower working temperature to ≤25°C, with ε_r = 575% ± 15% from temperatures ≤25°C to >400°C, and tan δ < 0.025 from 25°C to 400°C. Values of dc resistivity ranged from ~10⁹ Ω·m at 250°C to ~10⁶ Ω·m at 500°C. The properties suggest that this material may be of interest for high‐temperature capacitor applications.     

Structure,Microwave Dielectric Properties,and Low‐Temperature Sintering of Acceptor/Donor Codoped Li2Ti1−x(Al0.5Nb0.5)xO3 Ceramics

The structure, microwave dielectric properties, and low‐temperature sintering behavior of acceptor/donor codoped Li₂TiO₃ ceramics [Li₂Ti_1?x(Al_0.5Nb_0.5)_xO₃, x = 0–0.3] were investigated systematically. The x‐ray diffraction confirmed that a single‐phase solid solution remained within 0 < x ≤ 0.2 and secondary phases started to appear as x > 0.2, accompanied by an order–disorder phase transition in the whole range. Scanning electron microscopy observation indicated that the complex substitution of Al³⁺ and Nb⁵⁺ produced a significant effect on the microstructural morphology. Both microcrack healing and grain growth contributed to the obviously enhanced Q×f values. By comparison, the decrease of ε_r and τ_f values was ascribed to the ionic polarizability and the cell volume, respectively. Excellent microwave dielectric properties of ε_r ~ 21.2, Q×f ~ 181 800 GHz and τ_f  ~ 12.8 ppm/°C were achieved in the x = 0.15 sample when sintered at 1150°C. After 1.5 mol% BaCu(B₂O₅) additive was introduced, it could be well sintered at 950°C and exhibited good microwave dielectric properties of ε_r ~ 20.4, Q×f ~ 53 290 GHz and τ_f ~ 3.6 ppm/°C as well. The cofiring test of the low‐sintering sample with Ag powder proved its good chemical stability during high temperature, which enables it to be a promising middle‐permittivity candidate material for the applications of low‐temperature cofired ceramics.     

First‐Principles Insight into the Composition‐Dependent Structure and Properties of γ‐Alon

Spinel type Aluminum oxynitride (γ‐alon) solid solution exists in the Al₂O₃‐rich region of AlN–Al₂O₃ systems. The first‐principles calculations facilitate our investigations on composition‐dependence of structure and properties in γ‐alon without the limit of experimental solubility. The constant anion crystal structure of γ‐alon was described as the solid solution of spinel phase γ‐Al₂O₃ and the ideal Al₃O₃N with formula of Al_(8+x)/3O_4?xN_x (0 ≤ x ≤ 1). The unit cell expands with increasing Al₃O₃N composition. The lattice parameter increases nonlinearly with the composition of Al₃O₃N, which deviates from Vegard's law. As x increases, the anions dilate from the Al^IV along (1 1 1) direction, and two new narrow peaks (approximate –12.7 and –0.3 eV) become stronger and the conduction band presents a downward shift to low energy in the TDOS. The absorption edge in the UV region of ε₂(ω) present slight red‐shift of 0.5 eV as x increases. Because the compressibility was improved by expansion of coordination polyhedron, the elastic properties were just slightly enhanced as the nitrogen concentration increases. It is suggested that the notable enhancement of mechanical properties in γ‐alon may be difficult to yield by varying the content of substituted nitrogen atoms. The calculated results provide the basis for understanding the crystal structure and intrinsic properties of γ‐alon with different compositions.     

Microwave Dielectric Properties and Thermally Stimulated Depolarization Currents of (1 − x)MgTiO3–xCa0.8Sr0.2TiO3 Ceramics

(1 ? x)MgTiO₃–xCa_0.8Sr_0.2TiO₃ (0.04 ≤ x ≤ 0.2, MT‐CST) composite ceramics were prepared by the conventional solid‐state reaction process. The phase composition, microwave dielectric properties, and microwave dielectric loss mechanisms were studied. Ca_0.8Sr_0.2TiO₃ was employed as a τ_f compensator for MgTiO₃, and they coexisted well without forming any secondary phases. Interestingly, significant dielectric relaxations associated with oxygen vacancy defects were observed in all the MT‐CST ceramics through the dielectric‐temperature spectra. Thermally simulated depolarization current was therefore conducted to obtain the defects associated with extrinsic dielectric loss mechanisms. The concentrations of both defect dipole and in‐grain oxygen vacancies increased with the increasing x, which could induce microwave dielectric loss consequently. It demonstrated that the behaviors of Q × f were basically influenced by phase composition and defects here. Temperature‐stable ceramics can be achieved at x = 0.06, where the microwave dielectric properties were ε_r = 21.19, Q × f = 110 900 GHz (f = 9.295 GHz), and τ_f = ?0.9 ppm/°C, respectively.     

Structural,magnetic, electrical,and electrochemical properties of Sr–Co–Ru–O: A hybrid‐capacitor application

In this study, we report the synthesis of SrCo_1?xRu_xO_3?δ nominal compositions, where x = 0.0‐1.0, using solid‐state reaction technique. XRD analysis confirms the structure of x = 0 sample as hexagonal Sr₆Co₅O₁₅. As the Co ions are substituted by Ru, a two‐phase structure (hexagonal R32 and orthorhombic Pbnm) emerges up to x ≤ 0.5. As the Ru content is increased further, the hexagonal R32 phase disappears completely and an orthorhombic Pbnm phase becomes the main phase. SEM images show that grain size of the samples decreases with increasing Ru content. Temperature‐dependent electrical conductivity studies indicate upon Ru substitution in the nominal SrCo_1?xRu_xO_3?δ compounds, resistivity decreases due to appearance of metallic SrRuO₃ phase. The cyclic voltammogram (CV) of the samples show capacitive properties upon Ru substitution. The cycle measurements of the capacitors yield promising results for potential supercapacitor applications.     

Structural and Electrical Properties of Ni‐Substituted Mg‐Mn Nanoferrite by Coprecipitation Route

Ni²⁺ ions doped on Mg_0.40Mn_0.60‐xNi_xFe₂O₄ compositions with 0.00 ≤ x ≤ 0.60 have been synthesized by coprecipitation method and taken for the present work to study the dielectric properties and impedance characterization using the XRD and electrical measurements. The X‐ray diffraction and FT‐IR revealed that the ferrite has single‐phase cubic spinel structure. The calculated particle size from XRD data verified using SEM as well as AFM. These photographs show that the ferrites have crystalline size in the range of 20–50 nm. It was observed that the particle size decreased and Ni concentration increased. The dielectric constant and dielectric loss decreased with increase in nonmagnetic Ni²⁺ ions. Electrical properties indicate that synthesized nanoferrite particles have high resistivity.     

Piezoelectric properties of (Na0.5K0.5)(Nb1‐xSbx)O3‐SrTiO3 ceramics with tetragonal‐pseudocubic PPB structure

CuO‐added 0.96(Na_0.5K_0.5)(Nb_1‐xSb_x)O₃‐0.04SrTiO₃ ceramics sintered at the low temperature of 960°C for 10 hours showed dense microstructures and high relative densities. The specimens with 0.0 ≤  x ≤ 0.04 had orthorhombic‐tetragonal polymorphic phase boundary (PPB) structure. Tetragonal‐pseudocubic PPB structure was observed in specimens with 0.05 ≤  x ≤ 0.07, while the specimen with x = 0.08 has a pseudocubic structure. The structural variation in the specimens is explained by the decreases in the orthorhombic‐tetragonal transition temperature and Curie temperature with the addition of Sb⁵⁺ ions. The specimens with 0.05 ≤  x ≤ 0.07, which have tetragonal‐pseudocubic PPB structure, had large electric field‐induced strains of 0.14%‐0.016%. Moreover, these specimens also showed increased d₃₃ values between 280 pC/N and 358 pC/N. In particular, the specimen with x = 0.055 showed particularly enhanced piezoelectric properties: d₃₃ of 358 pC/N, k_p of 0.45, and the electric field‐induced strain of 0.16% at 4.5 kV/mm.     

Investigation on phase structure,spectral characteristics,microstructure and microwave dielectric properties of Li2Zn[Ti1-x(Co1/3Nb2/3)x]3O8 (0.0 ≤ x ≤ 0.4) ceramics

In this paper, a series of Li₂Zn[Ti_1-x(Co_1/3Nb_2/3)_x]₃O₈ (0.0 ≤ x ≤ 0.4) ceramics were prepared via the conventional solid-state method. The influences of (Co_1/3Nb_2/3)⁴⁺ complex ions on the phase composition, spectral characteristics, microstructure, and microwave dielectric properties of Li₂Zn[Ti_1-x(Co_1/3Nb_2/3)_x]₃O₈ ceramics were studied systematically. XRD analysis accompanied with Rietveld refinements showed that pure Li₂ZnTi₃O₈ solid solution ceramics with the cubic spinel structure were obtained at x = 0.2–0.4. New Raman-active mode of about 858 cm⁻¹ should be attributed to the vibrations of NbO₆ due to the high bond energy of Nb–O bonds, exerting a certain impact on the structure and performance of Li₂Zn[Ti_1-x(Co_1/3Nb_2/3)_x]₃O₈ ceramics. XPS results indicated that Nb⁵⁺ ion donor suppressed the deoxidation process and therefore resulted in the disappearance of Ti³⁺ ion and oxygen vacancy. The downward trend variation in the ε_r value with the increase of (Co_1/3Nb_2/3)⁴⁺ content could be explained by the presence of “compressed” cations and “rattling” cations effect. In addition, the Q × f of the current ceramics was closely dependent on relative density, grain size, FWHM, and oxygen vacancy. Good combined microwave dielectric properties of ε_r = 24.5, Q × f = 91,250 GHz, and τ_f = −16.8 ppm/°C were achieved for the Li₂Zn[Ti_0.8(Co_1/3Nb_2/3)_0.2]₃O₈ ceramic sintered at 1120 °C. High quality factor gives evidence that the Li₂Zn[Ti_0.8(Co_1/3Nb_2/3)_0.2]₃O₈ ceramic is an appealing candidate for highly selective microwave devices.     

Enhancement of the cation order and the microwave dielectric properties of Li2ZnTi3O8 through composition modulation

A series of Li₂ZnTi_3-xO₈ ceramics (0.04 ≤ x ≤ 0.16) were prepared by the conventional solid-state ceramic route. An obvious improvement in the order degree for the Li⁺ and Ti⁴⁺ ions in octahedral sites was achieved by deliberately introducing a slight Ti⁴⁺ non-stoichiometry. SAED, HRTEM, and Raman analysis confirmed a well-ordered B-site structure. Correspondingly, an obvious enhancement of the quality factor up to 108,000 GHz was demonstrated for Ti-deficient Li₂ZnTi_2.92O₈ ceramics, a 50% increase compared to the stoichiometric counterpart. Moreover, the infrared reflectivity spectrum of the Li₂ZnTi_2.92O₈ ceramic was used to disclose the intrinsic dielectric responses of a Li-based spinel for the first time. These results provide useful insights into the structure-property relation in the spinel material system.     

Surface barrier layer effect in (In + Nb) co‐doped TiO2 ceramics: An alternative route to design low dielectric loss

Giant dielectric permittivity (ε′) with low loss tangent (tanδ) was reported in (In + Nb) co‐doped TiO₂ ceramics. Either of electron‐pinned defect‐dipole or internal barrier layer capacitor model was proposed to be the origin of this high dielectric performance. Here, we proposed an effectively alternative route for designing low‐tanδ in co‐doped TiO₂ ceramics by creating a resistive outer surface layer. A pure rutile‐TiO₂ phase with a dense microstructure and homogeneous dispersion of dopants was achieved in (In + Nb) co‐doped TiO₂ ceramics prepared by a simple sol‐gel method. Two giant dielectric responses were observed in low‐ and high‐frequency ranges, corresponding to extremely high ε′≈10⁶‐10⁷ and large ε′≈10⁴‐10⁵, respectively. After annealing in air, a low‐frequency dielectric response disappeared and could be restored by removing the outer surface of the annealed sample, indicating the dominant electrode effect in the initial sample. Annealing can cause improved dielectric properties with a temperature‐ and frequency‐independent ε′ value of ≈1.9 × 10⁴ and cause a decrease in tanδ from 0.1 to 0.035. High dielectric performance in (In_0.5Nb_0.5)_xTi_1?xO₂ ceramics can be achieved by eliminating the electrode effect and forming a resistive outer surface layer.     

Microwave Dielectric Ceramics Li2MO4−TiO2 (M = Mo,W) with Low Sintering Temperatures

In this work, novel series of (1 ? x)Li₂MO₄–xTiO₂ (M = Mo, W; x = 0.3, 0.4, 0.45, 0.5, 0.6) ceramics were developed for microwave dielectric application. They were prepared via the mixed‐oxide process and the phase composition, microstructures, sintering behaviors, and microwave dielectric properties were investigated. The X‐ray diffraction (XRD) pattern and scanning electron microscope analysis indicated that the Li₂MO₄ (M = Mo, W) did not react with rutile TiO₂ and a stable two‐phase composite system Li₂MO₄–TiO₂ (M = Mo, W) was formed. The XRD pattern of cofired ceramics revealed that some parts of Li₂MoO₄ phase and very small part of Li₂WO₄ phase react with Ag to form Ag₂MoO₄ phase and Ag₂WO₄ phase, respectively. At x = 0.45–0.5, temperature stable microwave dielectric materials with low sintering temperature (700°C–730°C) were obtained: ε_r = 10.6–11.0, Qf = 30 060–32 800 GHz, and temperature coefficient of resonant frequency ~0 ppm/°C.