High strain (0.4%) Bi(Mg2/3Nb1/3)O3‐BaTiO3‐BiFeO3 lead‐free piezoelectric ceramics and multilayers

The relationship between the piezoelectric properties and the structure/microstructure for 0.05Bi(Mg_2/3Nb_1/3)O₃‐(0.95‐x)BaTiO₃‐xBiFeO₃ (BBFT, x = 0.55, 0.60, 0.63, 0.65, 0.70, and 0.75) ceramics has been investigated. Scanning electron microscopy revealed a homogeneous microstructure for x < 0.75 but there was evidence of a core‐shell cation distribution for x = 0.75 which could be suppressed in part through quenching from the sintering temperature. X‐ray diffraction (XRD) suggested a gradual structural transition from pseudocubic to rhombohedral for 0.63 < x < 0.70, characterized by the coexistence of phases. The temperature dependence of relative permittivity, polarization‐electric field hysteresis loops, bipolar strain‐electric field curves revealed that BBFT transformed from relaxor‐like to ferroelectric behavior with an increase in x, consistent with changes in the phase assemblage and domain structure. The largest strain was 0.41% for x = 0.63 at 10 kV/mm. The largest effective piezoelectric coefficient (d₃₃^*) was 544 pm/V for x = 0.63 at 5 kV/mm but the largest Berlincourt d₃₃ (148 pC/N) was obtained for x = 0.70. We propose that d₃₃^* is optimized at the point of crossover from relaxor to ferroelectric which facilitates a macroscopic field induced transition to a ferroelectric state but that d₃₃ is optimized in the ferroelectric, rhombohedral phase. Unipolar strain was measured as a function of temperature for x = 0.63 with strains of 0.30% achieved at 175°C, accompanied by a significant decrease in hysteresis with respect to room temperature measurements. The potential for BBFT compositions to be used as high strain actuators is demonstrated by the fabrication of a prototype multilayer which achieved 3 μm displacement at 150°C.     

Remarkably High‐Temperature Stability of Bi(Fe1−xAlx)O3–BaTiO3 Solid Solution with Near‐Zero Temperature Coefficient of Piezoelectric Properties

The 0.72Bi(Fe_1?xAl_x)O₃–0.28BaTiO₃ (x = 0, 0.01, 0.03, 0.05, and 0.07, abbreviated as BFAx–BT) lead‐free high‐temperature ceramics were prepared by the conventional ceramic processing. Systematic investigation on the microstructures, crystalline structures, dielectric and piezoelectric properties, and high‐temperature stability of piezoelectric properties was carried out. The crystalline structures of BFAx–BT ceramics evolve from rhombohedral structure with x < 0.01 to the coexistence of rhombohedral structure and pseudocubic phases with x ≈ 0.01, finally to pseudocubic phases when x > 0.03. Remarkably high‐temperature stability with near‐zero temperature coefficient of piezoelectric properties (TCk_p), together with improved piezoelectric properties has been achieved for x = 0.01 BFAx–BT ceramics. The BFAx–BT(x = 0.01) ceramics simultaneously show the excellent piezoelectric properties of d₃₃ = 151 pC/N, k_p = 0.31 and super‐high‐temperature stability of T_d = 420°C, TCk_p = 1 × 10^?4. It is considered that the observed strong piezoelectricity and remarkably high‐temperature stability should be ascribed to the phase coexistence of rhombohedral and pseudocubic phases. The rhombohedral phases have a positive TCk_p value and the pseudocubic phases possess a negative TCk_p value. Thus, the TCk_p value of BFAx–BT ceramics can be tuned by composition of x.     

Re-entrant ferroelectric relaxor phenomena in the (1 − x)[Bi1/2(Na1/2K1/2)1/2TiO3]-xPbZrO3 system

The solid solution (1 − x)[Bi_1/2(Na_1/2K_1/2)_1/2TiO₃]-xPbZrO₃, (0.00 ≤ x ≤ 0.12) was investigated to examine the phase equilibria, dielectric and electromechanical properties. The composition corresponding to x = 0.00 exhibits tetragonal symmetry with the expected classical ferroelectric (FE) behavior. The system exhibited FE to relaxor crossover with the addition of lead zirconate at the composition x = 0.05. This is indicated by typical relaxor characteristics such as a transition to the global pseudocubic phase, a constriction in the FE hysteresis loop, and a sudden decrease in the negative strain accompanied by an increase in maximum strain. Most notably, with a further increase in x (>0.05), there is evidence for a return to a FE phase that exhibits classical FE characteristics. The combined results demonstrate that there exists a narrow FE-relaxor boundary near x = 0.05, where FE and relaxor phases coexist. At the critical composition, enhancement in the piezoelectric properties, including an increase in the effective (350 pm/V) was observed. This transition in the electromechanical properties is consistent with changes observed in the phase equilibria for this solid solution. The crystal structure transitions from tetragonal symmetry for x = 0.00, to pseudocubic symmetry for the relaxor compositions (x = 0.05), and finally to a lower symmetry perovskite phase for the re-entrant FE phase (x> 0.05). This composition-induced transition from FE to relaxor to a re-entrant FE state in the (1 − x)[Bi_1/2(Na_1/2K_1/2)_1/2TiO₃]-xPbZrO₃ system is unusual among relaxor FE systems and thus is of great scientific and technological interest.     

Composition‐ and Temperature‐Dependent Large Strain in (1−x)(0.8Bi0.5Na0.5TiO3–0.2Bi0.5K0.5TiO3)– xNaNbO3 Ceramics

Ternary solid solutions of (1 ? x)(0.8Bi_0.5Na_0.5TiO₃–0.2Bi_0.5K_0.5TiO₃)– xNaNbO₃ (BNKT–xNN) lead‐free piezoceramics were fabricated using a conventional solid‐state reaction method. Pure BNKT composition exhibited an electric‐field‐induced irreversible structural transition from pseudocubic to ferroelectric rhombohedral phase at room temperature. Accompanied with the ferroelectric‐to‐relaxor temperature T_F‐R shifted down below room temperature as the substitution of NN, a compositionally induced nonergodic‐to‐ergodic relaxor transition was presented, which featured the pinched‐shape polarization and sprout‐shape strain hysteresis loops. A strain value of ~0.445% (under a driving field of 55 kV/cm) with large normalized strain of ~810 pm/V was obtained for the composition of BNKT–0.04NN, and the large strain was attributed to the reversible electric‐field‐induced transition between ergodic relaxor and ferroelectric phase.     

Thermally Stable BaTiO3‐Bi(Mg2/3Nb1/3)O3 Solid Solution with High Relative Permittivity in a Broad Temperature Usage Range

A combined X‐ray diffraction (XRD), Raman spectra, X‐ray photoelectron spectroscopy, Scanning electron microscopy, and dielectric characterization of (1–x)BaTiO₃?xBi(Mg_2/3Nb_1/3)O₃ ceramic system were investigated for compositions of 0 ≤ x ≤ 0.2. Single‐phase perovskite‐type XRD patterns were observed for all compositions. A systematically structural change from tetragonal to pseudocubic symmetry occurred at 0.04 < x < 0.06, which agrees well with the analysis of Raman spectra. Dielectric measurements indicated that the crossover from a classic ferroelectric to relaxor ferroelectric occurred at x ≥ 0.04. Compared with other compositions, the temperature independence of relative permittivity at T > T_m significantly ameliorated at x = 0.1: near‐stable temperature coefficient of higher relative permittivity (~6800 ± 15%) and the corresponding loss tanδ ≤ 0.09 over a more broader temperature range of 25°C–240°C (1 kHz), which indicates that this ceramic is a promising dielectric material for elevated temperature dielectrics.     

The Relationship Between Phase Structure and Electrical Properties in (1 − x)(Bi0.5Na0.5TiO3–Ba0.5K0.5TiO3–BaTiO3)‐ xK0.5Na0.5NbO3 Quaternary Lead‐Free Piezoelectric Ceramics

(1 ? x)(0.85Bi_0.5Na_0.5TiO₃–0.11Ba_0.5K_0.5TiO₃–0.04BaTiO₃)‐ xK_0.5Na_0.5NbO₃ lead‐free piezoelectric ceramics with x = 0.00, 0.02, 0.03, 0.04, 0.05, and 0.10 were prepared by a conventional solid state method. A coexistence of rhombohedral (R) and tetragonal (T) phases was found in the system, which tended to evolve into pseudocubic symmetry when x increases. The x = 0.04 sample exhibited improved electrical properties: the dielectric constant ε_r = 1900 with the low loss tangents 0.06, the S_max/E_max of ~400 and ~460 pm/V under unipolar and bipolar electric field, respectively. Meanwhile, piezoelectric constant d₃₃ still maintained ~160 pC/N. These could be owed to the formation of polar nanoregions for relaxor phase.     

Novel BiFeO3–BaTiO3–Ba(Mg1/3Nb2/3)O3 Lead‐Free Relaxor Ferroelectric Ceramics for Energy‐Storage Capacitors

A novel lead‐free relaxor ferroelectric ceramic of (0.67?x)BiFeO₃–0.33BaTiO₃–xBa(Mg_1/3Nb_2/3)O₃ [(0.67?x)BF–0.33BT–xBMN, x = 0–0.1] was prepared by a solid‐state reaction method. A relatively high maximum polarization P_max of 38 μC/cm² and a low remanent polarization P_r of 5.7 μC/cm² were attained under 12.5 kV/mm in the x = 0.06 sample, leading to an excellent energy‐storage density of W ~1.56 J/cm³ and a moderate energy‐storage efficiency of η ~75%. Moreover, a good temperature stability of the energy storage was obtained in the x = 0.06 sample from 25°C to 190°C. The achievement of these characteristics was basically attributed to an electric field induced reversible ergodic to ferroelectric phase transition owing to similar free energies near a critical freezing temperature. The results indicate that the (0.67?x)BF–0.33BT–xBMN lead‐free realxor ferroelectric ceramic could be a promising dielectric material for energy‐storage capacitors.     

Phase Diagram and Properties of High TC/TR−T Pb(In1/2Nb1/2) O3–Pb(Zn1/3Nb2/3)O3–PbTiO3 Ferroelectric Ceramics

A ternary ferroelectric ceramic system, (1?x?y)Pb(In_1/2Nb_1/2)O₃–xPb(Zn_1/3Nb_2/3)O₃–yPbTiO₃ (PIN–PZN–PT, x = 0.21, 0.27, 0.36, 0.42), was prepared using a two‐step precursor method. The phase structure, dielectric, piezoelectric, and ferroelectric properties of the ternary ceramics were systematically investigated. A morphotropic phase boundary (MPB) was identified by X‐ray diffraction. The optimum piezoelectric and electromechanical properties were achieved for a composition close to MPB (0.5PIN–0.21PZN–0.29PT), where the piezoelectric coefficient d₃₃, planar electromechanical coupling factor k_p, and remnant polarization P_r are 660 pC/N,72%, and 45 μC/cm², respectively. The Curie temperature T_C and rhombohedral to tetragonal phase transition temperature T_R?T were also derived by temperature dependence of dielectric measurements. The strongly “bended” MPB in the PIN–PT system was found to be “flattened” after addition of PZN in the PIN–PT–PZN system. The results demonstrate a possibility of growing ferroelectric single crystals with high electromechanical properties and expanded range of application temperature.     

Normal‐Relaxor‐Diffuse Ferroelectric Phase Transition and Electrical Properties of Bi(Mg1/2Ti1/2)3–PbZrO3–PbTiO3 Solid Solution Ceramics Near the Morphotropic Phase Boundary

Perovskite‐type xBi(Mg_1/2Ti_1/2)O₃–(0.56 ? x)PbZrO₃–0.44PbTiO₃ (xBMT–PZ–PT) ternary solid solution ceramics were synthesized via a conventional solid‐state reaction method. The phase transition behaviors, dielectric, ferroelectric, and piezoelectric properties were investigated as a function of the BMT content. The X‐ray diffraction analysis showed that the tetragonality of xBMT–PZ–PT was enhanced with increasing the BMT content, and a morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases was identified approximately in the composition of x = 0.08. In addition, the dielectric diffuseness and frequency dispersion behavior were induced with the addition of BMT and a normal‐relaxor‐diffuse ferroelectric transformation was observed from the PZ‐rich side to the BMT‐rich side. The electrical properties of xBMT–PZ–PT ceramics exhibit obviously compositional dependence. The x = 0.08 composition not only possessed the optimum properties with ε^T₃₃/ε₀ = 1450, Q_m = 69, d₃₃ = 390 pC/N, k_p = 0.46, P_r = 30 μC/cm², E_c = 1.4 kV/mm, T_c = 325°C, and a strain of 0.174% (d₃₃^* = 436 pm/V) under an electric field of 4 kV/mm as a result of the coexistence of two ferroelectric phases near the MPB, but also owned a good thermal‐depolarization behavior with a d₃₃ value of >315 pC/N up to 290°C and a frequency‐insensitive strain behavior.     

Enhanced Dielectric and Ferroelectric Properties of Pb(Mg1/3Nb2/3)0.65Ti0.35O3 Ceramics by ZnO Modification

Phase formation, microstructures, dielectric, and ferroelectric properties of ZnO‐modified Pb(Mg_1/3Nb_2/3)_0.65Ti_0.35O₃ (PMNT/xZnO, where x = 0, 0.4, 2.0, 4.0, and 11.0 mol%) ceramics were studied. A coexistence of rhombohedral and tetragonal ferroelectric phases was observed at room temperature in all samples. The ceramics with the relative densities of 93%–95% were prepared. The modification by ZnO led to an increase in grain sizes of PMNT ceramics. The maximum dielectric constant of the pure PMNT ceramic was increased with x = 0.4–4.0 mol% ZnO doping, with the highest value being observed in the 2.0 mol% sample. Both the temperature at which the transition between rhombohedral and tetragonal ferroelectric phases took place (T_R‐T) and the Curie temperature of the ceramics tended to increase with increasing x. The ferroelectric properties were enhanced with increased remanent polarization and P(E) loop squareness in the compositions with x = 0.4–4.0 mol%. However, the ferroelectric properties were attenuated with x = 11.0 mol%.     

Relaxor Characteristics of the Phase Transformation in (1 − x)BaTiO3–xBi(Zn1/2Ti1/2)O3 Perovskite Ceramics

The single‐phase solid solutions of the (1 ? x)BaTiO₃–(x)Bi(Zn_1/2Ti_1/2)O₃ (BT–BZT) where x = 0.02–0.15 were prepared to investigate dielectric properties. Crystal structure of samples was obtained by using an X‐ray diffraction technique and Raman spectroscopy. For compositions with x ≤ 0.08, the solid solutions exhibited clear tetragonal symmetry and transitioned to pseudocubic symmetry as the content of BZT increased. The dielectric response exhibited a sharp phase transition within the BT‐rich region and the composition 0.92BT–0.08BZT was characterized by the onset of relaxor characteristics. As the concentration of BZT increased, the phase transition exhibited broader and more diffuse behavior. The polarization as a function of electric field (P–E) of these solid solutions also exhibited the same trend. The BT‐rich compositions showed a normal ferroelectric P–E response with a decrease in loop area as the BZT content increased. The composition at x = 0.08 exhibited a pinched hysteresis loop and with further increase in BZT content, the P–E response was characterized by slim loops.     

Effects of A1/A2‐Sites Occupancy upon Ferroelectric Transition in (SrxBa1−x)Nb2O6 Tungsten Bronze Ceramics

The dielectric and ferroelectric characteristics of (Sr_xBa_1?x)Nb₂O₆ unfilled tungsten bronze ceramics have been investigated together with the structure. The dielectric and ferroelectric characteristics of the present ceramics vary significantly with x, and the A1/A2‐sites occupancy has been determined as the primary parameter governing this variation tendency. Ba ions tend to occupy A2‐sites, Sr ions tend to occupy A1‐sites, and one A1‐site is empty. When the ratio of Sr/Ba is close to 1:4 (where four A2‐sites are just occupied by Ba ions, and one A1‐site is occupied by Sr ion while another A1‐site is empty), the normal ferroelectric transition is observed with one anomaly in the tanδ–T curve (x = 0.25). When the ratio of Sr/Ba is far away from 1:4, the typical relaxor behavior is indicated together with three anomalies in the tanδ–T curve (x = 0.75). The incommensurate oxygen octahedral tilting and A‐site random distribution are considered to be the structure origins for the relaxor ferroelectricity and low temperature dielectric relaxations.     

Preparation and characterization of Pb(Lu1/2Nb1/2)O3–Pb(In1/2Nb1/2)O3–PbTiO3 ternary ferroelectric ceramics with high phase transition temperatures

To explore new relaxor‐PbTiO₃ systems for high‐power and high‐temperature electromechanical applications, a ternary ferroelectric ceramic system of Pb(Lu_1/2Nb_1/2)O₃–Pb(In_1/2Nb_1/2)O₃–PbTiO₃ (PLN–PIN–PT) have been investigated. The phase structure, dielectric, piezoelectric, and ferroelectric properties of the as‐prepared PLN–PIN–PT ceramics near the morphotropic phase boundary (MPB) were characterized. A high rhombohedral‐tetragonal phase transition temperature T_R‐T of 165°C and a high Curie temperature T_C of 345°C, together with a good piezoelectric coefficient d₃₃ of 420 pC/N, were obtained in 0.38PLN–0.20PIN–0.42PT ceramics. Furthermore, for (0.8?x)PLN–0.2PIN–xPT ceramics, the temperature‐dependent piezoelectric coefficients, coercive fields and electric‐field‐induced strains were further studied. At 175°C, their coercive fields were found to be above 9.5 kV/cm, which is higher than that of PMN–PT and soft P5H ceramics at room temperature, indicating PLN–PIN–PT ceramics to be one of the promising candidates in piezoelectric applications under high‐driven fields. The results presented here could benefit the development of relaxor‐PbTiO₃ with enhanced phase transition temperatures and coercive fields.     

Strain properties of (1-x)Bi0.5Na0.4K0.1TiO3-xBi(Mg2/3Ta1/3)O3 electroceramics

A ternary solid solution of Bi_0.5Na_0.5TiO₃–Bi_0.5K_0.5TiO₃–Bi(Mg_2/3Ta_1/3)O₃ (BNKT-xBMT) lead-free electroceramics was synthesized by a solid-state reactive sintering technique. The electrostrain, dielectric, and ferroelectric properties as well as the impedance characteristics and the microstructure were systematically assessed. With the increase of BMT, the BNKT-xBMT ceramics gradually transformed from non-ergodic relaxor phase to ergodic relaxor phase, manifested as the ferroelectric-to-relaxor temperature (T_F-R) shifts towards below room temperature. Additionally, the ferroelectric hysteresis curves became pinched, and the strain curve changed from butterfly-shaped into sprout-shaped. At the ergodic relaxor composition of x = 0.04, a large electrostrain value (S = 0.4%; under an electric field of 60 kV/cm, d₃₃* = 632 pm/V) was achieved, which is mainly attributed to the electric-field-induced transition from the ergodic relaxor phase to the ferroelectric phase.     

Temperature‐Dependent Phase Transitions in the Lead‐Free Piezoceramics (1 – x – y)(Bi1/2Na1/2)TiO3–xBaTiO3–y(K0.5Na0.5)NbO3 Observed by in situ Transmission Electron Microscopy and Dielectric Measurements

Lead‐free piezoelectric (1 – x – y)(Bi_1/2Na_1/2)TiO₃–xBaTiO₃–y(K_0.5Na_0.5)NbO₃ (BNT–BT–KNN) ceramics were examined in situ under increasing temperature in the transmission electron microscope. Changing superstructure reflections indicate a transition from rhombohedral to tetragonal to cubic phase with broad coexistence regions. The additional evolution of the microstructure in combination with dielectric measurements leads to a model of two relaxor‐type phase evolutions with temperature.     

Effect of BiMeO3 on the Phase Structure,Ferroelectric Stability,and Properties of Lead‐Free Bi0.5(Na0.80K0.20)0.5TiO3 Ceramics

The effects of BiMeO₃ (Me = Fe, Sc, Mn, Al) addition on the phase transition and electrical properties of Bi_0.5(Na_0.80K_0.20)_0.5TiO₃ (BNKT20) lead‐free piezoceramics were systematically investigated. Results showed that addition of BiFeO₃ into BNKT20 induces a phase transition from tetragonal–rhombohedral coexisted phases to a tetragonal phase with the observation of enhanced piezoelectric properties (d₃₃ = 150 pC/N for 0.02BiFeO₃). BiScO₃, BiMnO₃, and BiAlO₃ substitutions into BNKT20 induce a phase transition from coexistence of ferroelectric tetragonal and rhombohedral to a relaxor pseudocubic with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F–R to room temperature. Accordingly, large accompanying normalized strains of 0.34%–0.36% are obtained near the ferroelectric–relaxor phase boundary, and the mergence of large strain response can be ascribed to a reversible field‐induced ergodic relaxor‐to‐ferroelectric phase transformation. Moreover, our study also revealed that the composition located at the ferroelectric–relaxor phase boundary where the strain response is consistently derivable shifts to a BNKT20‐rich composition as the tolerance factor t of the end‐member BiMeO₃ increases, and this relationship is expected to provide a guideline for designing high‐performance (Bi_0.5Na_0.5)TiO₃‐based materials by searching the ferroelectric–relaxor phase boundary.     

Large Piezoelectric Response and Polarization in Relaxor Ferroelectric PbTiO3–Bi(Ni1/2Zr1/2)O3

New binary system (1?x) PbTiO₃?xBi(Ni_1/2Zr_1/2)O₃ (PT–100x BNZ) with x ≤ 0.45 were synthesized via solid‐state reaction route. A morphotropic phase boundary (MPB) was identified around x = 0.40 by X‐ray diffraction (XRD) method. The ceramics with MPB composition exhibit enhanced ferroelectric properties. A large piezoelectric coefficient (d₃₃) up to 400 pC/N was obtained for the PT–40BNZ, which is comparable with the PbTiO₃–BiScO₃ (PT–BS, 450 pC/N).The frequency dependence of dielectric permittivity of PT–40BNZ shows characteristic of a strong relaxor feature and a transition temperature around 290°C (1 MHz). Temperature effect on the unipolar strain was also investigated. The present system with high d₃₃ is a competitive piezoelectric material, as no expensive oxide is used here compared with the PT–BS.     

The Composition and Temperature‐Dependent Structure Evolution and Large Strain Response in (1−x)(Bi0.5Na0.5)TiO3−xBa(Al0.5Ta0.5)O3 Ceramics

The (1?x) (Bi_0.5Na_0.5)TiO₃?xBa(Al_0.5Ta_0.5)O₃((1?x)BNT‐xBAT) lead‐free piezoceramics was fabricated using a conventional solid‐state reaction method. The temperature and composition‐dependent strain behavior, dielectric, ferroelectric (FE), piezoelectric, and pyroelectric properties have been systematically investigated to develop lead‐free piezoelectric materials with large strain response for actuator application. As the BAT content increased, the FE order is disrupted resulting in a degradation of the remanent polarization, coercive field, and the depolarization temperature (T_d). A large strain of 0.36% with normalized strain d₃₃* = 448pm/V was obtained for the optimum composition x = 0.045 at room temperature. The bipolar and unipolar strains for the compositions x = 0.035 and x = 0.04 reach almost identical maximum values when the temperature is in the vicinity of their respective depolarization temperature (T_d). The Raman‐spectra analysis, macroscopic properties, thermal depolarization results, and temperature‐dependent relationships of both polarization and strain demonstrated that the origin of the large strain response for this investigated system is attributed to a field‐induced relaxor to FE phase transformation.     

Enhanced Multiferroic and Magnetocapacitive Properties of (1 − x)Ba0.7Ca0.3TiO3–xBiFeO3 Ceramics

The structures, Curie temperature, dielectric relaxor behaviors, ferroelectricity, ferromagnetism, and magnetocapacitance of the (1?x)Ba_0.70Ca_0.30TiO₃–xBiFeO₃ [(1?x)BCT–xBF, x = 0–0.90] solid solutions have been systematically investigated. The ceramics have coexisted tetragonal (T) and orthorhombic (O) phases when x ≤ 0.06, coexisted pseudocubic (PC) and O phases when x = 0.065, coexisted cubic and O phases when 0.07 ≤ x ≤ 0.12, PC phase when 0.21 ≤ x ≤ 0.42, coexisted T and rhombohedral (R) phases when 0.52 ≤ x ≤ 0.70, and R phase when x ≥ 0.75. Significantly, composition‐dependent microstructures and Curie temperature are observed, the average grain size increases from 1.9 μm for x = 0, reaches 12.0 μm for x = 0.67, and then decreases to 1.3 μm for x = 0.90. At room temperature, the ceramics with x = 0.42–0.70 show piezoelectric properties and multiferroic behaviors, characterized by the polarization‐electric field, polarization current intensity–electric field, and magnetization–magnetic field curves, the composition with x = 0.67 has maximum polarization, remnant polarization, maximum magnetization, and remnant magnetization of 15.0 μC/cm², 9.1 μC/cm², 0.33 emu/g, and 0.14 emu/g, respectively. In addition, the magnetocapacitance is evidenced by the increased relative dielectric constant with increasing the applied magnetic field (H). With ΔH = 8 kOe, the composition with x = 0.67 shows the largest values of (ε_r(H) ? ε_r(0))/ε_r(0) = 2.96% at room temperature. The structure–property relationship is discussed intensively.     

Temperature‐insensitive strain behavior in 0.99[(1−x)Bi0.5(Na0.80K0.20)0.5TiO3−xBiFeO3]–0.01Ta lead‐free piezoelectric ceramics

Lead‐free 0.99[(1?x)Bi_0.5(Na_0.80K_0.20)_0.5TiO₃?xBiFeO₃]–0.01Ta (BNKT20–100xBF–1Ta) lead‐free piezoelectric ceramics were fabricated through conventional solid state sintering method. Results showed that change of BF content in the BNKT20–100xBF–1Ta induced a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order. A large electric‐field‐induced strain of 0.36% (at 80 kV/cm driving field, corresponding to a large signal of ~450 pm/V) which is derived from a reversible field‐induced ergodic relaxor to ferroelectric phase transformation, was obtained in the composition with x=0.01 near the ferroelectric‐ergodic relaxor phase boundary. Moreover, an attractive property for application in nonlinear actuators demanding enhanced thermal stability was obtained in this material, which showed a temperature‐insensitive strain characteristic in the temperature range from room temperature to 100°C.