Effect of the densification of C–S–H on hydration kinetics of tricalcium silicate

Effect of water to cement (w/c) ratio and temperature profiles on the densification of C–S–H (calcium silicate hydrate gel) and hydration kinetics of triclinic tricalcium silicate (C₃S) is studied beyond the first day of hydration. Calorimetry and quantitative X‐ray diffraction/Rietveld analysis show that degree of hydration is unaffected by w/c up to 7 days and marginally thereafter. Coupling the degree of hydration with the portlandite content measured from thermal analysis indicate that C/S ratio of C–S–H decreases with increasing w/c. There is a clear increase in the portlandite content with increasing w/c, even though the degree of hydration is unchanged, due to the variations in C/S ratio of C–S–H. On the other hand, when C₃S is initially cured at a lower temperature (20°C) and then at a higher temperature (40°C), there is a significant increase in the reactivity even until 28 days and vice versa. These experimental results were explained using the densified volumetric growth hypothesis, which assumes that hydration kinetics are dependent on the internal surface area of C–S–H.     

Soft X‐ray Ptychographic Imaging and Morphological Quantification of Calcium Silicate Hydrates (C–S–H)

Morphological details of calcium silicate hydrate (C–S–H) stemming from the hydration process of Portland cement (PC) phases are crucial for understanding the PC‐based systems but are still only partially known. Here we introduce the first soft X‐ray ptychographic imaging of tricalcium silicate (C₃S) hydration products. The results are compared using both scanning transmission X‐ray and electron transmission microscopy data. The evidence shows that ptychography is a powerful method to visualize the details of outer and inner product C–S–H of fully hydrated C₃S, which have fibrillar and an interglobular structure with average void sizes of 20 nm, respectively. The high‐resolution ptychrography image enables us to perform morphological quantification of C–S–H, and, for the first time, to possibly distinguish the contributions of inner and outer product C–S–H to the small angle scattering of cement paste. The results indicate that the outer product C–S–H is mainly responsible for the q^?3 regime, whereas the inner product C–S–H transitions to a q^?2 regime. Various hypotheses are discussed to explain these regimes.     

C–(N)–S–H and N–A–S–H gels: Compositions and solubility data at 25°C and 50°C

Calcium silicate hydrates containing sodium [C–(N)–S–H], and sodium aluminosilicate hydrates [N–A–S–H] are the dominant reaction products that are formed following reaction between a solid aluminosilicate precursor (eg, slags, fly ash, metakaolin) and an alkaline activation agent (eg NaOH) in the presence of water. To gain insights into the thermochemical properties of such compounds, C–(N)–S–H and N–A–S–H gels were synthesized with compositions: 0.8≤Ca/Si≤1.2 for the former, and 0.25≤Al/Si≤0.50 (atomic units) for the latter. The gels were characterized using thermogravimetric analysis (TGA), scanning electron microscopy with energy‐dispersive X‐ray microanalysis (SEM‐EDS), and X‐ray diffraction (XRD). The solubility products (K_S0) of the gels were established at 25°C and 50°C. Self‐consistent solubility data of this nature are key inputs required for calculation of mass and volume balances in alkali‐activated binders (AABs), and to determine the impacts of the precursor chemistry on the hydrated phase distributions; in which, C–(N)–S–H and N–A–S–H compounds dominate the hydrated phase assemblages.     

Effect of synthesis procedure on carbonation of calcium‐silicate‐hydrate

Carbonation of synthesized calcium‐silicate‐hydrate (C–S–H) is difficult to avoid and can have significant impact on the molecular structure. Considerable carbonation was observed in C–S–H synthesized from the double decomposition of sodium silicate and calcium nitrate solutions but not in C–S–H synthesized from the direct reaction of fumed silica and calcium hydroxide solution. In order to isolate the cause of the greater carbonation in C–S–H synthesized by double decomposition, carbonation was induced in phase‐pure C–S–H by reaction with four different water‐based solutions containing dissolved CO₂ with varying pH and alkali content. Powder X‐ray diffraction, thermogravimetric analysis, and ²⁹Si nuclear magnetic resonance were used to probe the carbonation and the resulting changes in molecular structure. The pH of the solution was seen to strongly influence the degree of carbonation, while the alkali content had much less effect.     

Effect of Temperature on C3S and C3S + Nanosilica Hydration and C–S–H Structure

This study aimed to monitor the effect of temperature and the addition of nanosilica on the nanostructure of the C–S–H gel forming during tricalcium silicate (C₃S) hydration. Two types of paste were prepared from a synthesized T₁ C₃S. The first consisted of a blend of deionized water and C₃S at a water/solid ratio of 0.425. In the second, a 90 wt% C₃S + 10 wt% of nanosilica blend was mixed with water at a water/solid ratio of 0.7. The pastes were stored in closed containers at 100% RH and 25°C, 40°C, or 65°C. The hydration reaction was detained after 1, 14, 28, or 62 d with acetone, and then pastes were studied by ²⁹Si magic angle spinning nuclear magnetic resonance (²⁹Si MAS NMR).The main conclusion was that adding nSA expedites C₃S hydration at any age or temperature and modifies the structure of the C–S–H gel formed, two types of C–S–H gel appear. At 25°C and 40°C, more orderly, longer chain gels are initially (1 d) obtained as a result of the pozzolanic reaction between nSA and portlandite (CH) (C–S–H_II gel formation). Subsequently, ongoing C₃S hydration and the concomitant flow of dimers shorten the mean chain length in the gel.     

Soft X‐ray Spectromicroscopic Investigation of Synthetic C‐S‐H and C3S Hydration Products

Calcium silicate hydrates (C‐S‐H), the primary binding phase in concrete, is the most prominent physiochemical factor controlling the mechanical and chemical properties in the production of concrete. This paper reports the local‐binding structure and morphological details of C‐S‐H as determined by high‐resolution X‐ray spectromicroscopy. Hydrated tricalcium silicate (C₃S) was used to determine the properties and role of the outer products (Op) of C₃S. C‐S‐H with different molar ratios of Ca/Si, were synthesized (Syn‐CSH) to quantitatively evaluate the effect of silicate polymerization on Ca L and Si K edge of C‐S‐H. Near edge X‐ray absorption fine structure (NEXAFS) spectroscopy of Syn‐CSH showed no variation in peak positions and energy separation for CaL_{III, II} edge for the Ca/Si ratios investigated. Compared to Syn‐CSH, C₃S, when hydrated for 17 d, had a similar local structure around Ca. Si K edge NEXAFS analysis on Syn‐CSH showed a tendency for the peak positions of both the Si K edge and the peak induced by multiple scattering to shift to higher energy levels. The results also indicated that the distance between the two peaks increased with a decrease of the Ca/Si ratio in Syn‐CSH. Silicate polymerization influenced the multiple scattering of distant shell atoms more than the binding energy of the core atoms. Op of C₃S had a uniform and higher degree of silicate polymerization compared to the core area. The results imply that Op reduces the hydration process of C₃S into the core area thereby playing a key role on the properties of concrete upon formation.     

ZrB2–SiC–G Composite Prepared by Spark Plasma Sintering of In‐Situ Synthesized ZrB2–SiC–C Composite Powders

To avoid introduction of milling media during ball‐milling process and ensure uniform distribution of SiC and graphite in ZrB₂ matrix, ultrafine ZrB₂–SiC–C composite powders were in‐situ synthesized using inorganic–organic hybrid precursors of Zr(OPr)₄, Si(OC₂H₅)₄, H₃BO₃, and excessive C₆H₁₄O₆ as source of zirconium, silicon, boron, and carbon, respectively. To inhabit grain growth, the ZrB₂–SiC–C composite powders were densified by spark plasma sintering (SPS) at 1950°C for 10 min with the heating rate of 100°C/min. The precursor powders were investigated by thermogravimetric analysis–differential scanning calorimetry and Fourier transform infrared spectroscopy. The ceramic powders were analyzed by X‐ray diffraction, X‐ray photoelectron spectroscopy, and scanning electron microscopy. The lamellar substance was found and determined as graphite nanosheet by scanning electron microscopy, Raman spectrum, and X‐ray diffraction. The SiC grains and graphite nanosheets distributed in ZrB₂ matrix uniformly and the grain sizes of ZrB₂ and SiC were about 5 μm and 2 μm, respectively. The carbon converted into graphite nanosheets under high temperature during the process of SPS. The presence of graphite nanosheets alters the load‐displacement curves in the fracture process of ZrB₂–SiC–G composite. A novel way was explored to prepare ZrB₂–SiC–G composite by SPS of in‐situ synthesized ZrB₂–SiC–C composite powders.     

Structure Property Relationship in BaTiO3–Na0.5Bi0.5TiO3–Nb2O5–NiO X8R System

A novel BaTiO₃–Na_0.5Bi_0.5TiO₃–Nb₂O₅–NiO (BT‐NBT‐Nb‐Ni) system that meets the X8R specification (?55°C–150°C, ΔC/C≤±15%) of multilayer ceramic capacitors (MLCCs) was fabricated, with a maximum dielectric constant of 2350 at room temperature (25°C). Core–shell microstructure was observed by transmission electron microscopy (TEM), accounting for the good dielectric temperature stability. The role of Ni on the formation of core–shell structure and phase structure, and the subsequent relationship between structure and dielectric/ionic conduction properties were investigated. It was observed that the addition of Ni could adjust the ratio of core/shell, and significantly reduces the dielectric loss over the studied temperature range. A new Ba₁₁(Ni, Ti)₂₈O_66+x phase with a 10‐layer close‐packed structure was identified by X‐ray diffraction (XRD), serving as a source of oxygen vacancies for ionic conduction in addition to Ba(Ni,Ti)O₃. Furthermore, the impedance spectroscopy measurements demonstrated the remarkable impact of these Ni‐induced oxygen vacancies on both the grain and grain‐boundary conductivities.     

Characterization of C–S–H and C–A–S–H phases by electron microscopy imaging,diffraction, and energy dispersive X‐ray spectroscopy

Improving concrete sustainability by increasing durability requires a detailed knowledge about microstructural properties. Due to the nanoscale nature of hydrate phases that determine concrete properties, microstructural characterization remains a challenge. Analytical electron microscopy offers promising techniques to characterize cement hydrates. In this study, electron microscopy imaging, diffraction, and energy dispersive X‐ray spectroscopic information are combined in order to compare the structural properties of calcium silicate hydrate (C–S–H) and calcium aluminum silicate hydrate (C–A–S–H) phases. Results are shown for 28 days hydrated C–(A)–S–H of portland cement and cement containing ground granulated blast‐furnace slag (GGFBS). Electron diffraction patterns of single fibrous C–S–H and foil‐like C–A–S–H phases reveal a nanocrystalline structure. Also, it is shown by electron diffraction pattern that the crystal structures of C–S–H and C–A–S–H phases are similar. It is confirmed that the crystal structure of 14 Å tobermorite serves as good base for the structure of C–S–H. The electron diffraction patterns of fibrous C–S–H show streaks which indicate stacking faults, proofing that polymerization of silicate chains in C–S–H is limited. Here, we demonstrate for the first time that the dreierketten silicate chains contained in the C–S–H structure are oriented in parallel to the long axis of C–S–H fibers. This finding should be implemented in modeling of crystal growth of C–S–H.     

Pair distribution function analysis of nanostructural deformation of calcium silicate hydrate under compressive stress

Despite enormous interest in calcium silicate hydrate (C–S–H), its detailed atomic structure and intrinsic deformation under an external load are lacking. This study demonstrates the nanostructural deformation process of C–S–H in tricalcium silicate (C₃S) paste as a function of applied stress by interpreting atomic pair distribution function (PDF) based on in situ X‐ray scattering. Three different strains in C₃S paste under compression were compared using a strain gauge, Bragg peak shift, and the real space PDF. PDF refinement revealed that the C–S–H phase mostly contributed to PDF from 0 to 20 Å whereas crystalline phases dominated that beyond 20 Å. The short‐range atomic strains exhibited two regions for C–S–H: I) plastic deformation (0‐10 MPa) and II) linear elastic deformation (>10 MPa), whereas the long‐range deformation beyond 20 Å was similar to that of Ca(OH)₂. Below 10 MPa, the short‐range strain was caused by the densification of C–S–H induced by the removal of interlayer or gel‐pore water. The strain is likely to be recovered when the removed water returns to C–S–H.     

Controllable Formation of the Crystalline Phases in Ge–Ga–S Chalcogenide Glass‐Ceramics

We prepared chemically stoichiometric, S‐poor and S‐rich Ge–Ga–S glasses and annealed them at a temperature that was 20°C higher than its respective glass transition temperature. We aimed at tuning the formation of the different crystals in chalcogenide glass‐ceramics. Through systematic characterization of the structure using X‐ray diffraction and Raman scattering spectra, we found that, GeS₂ and GeS crystals only can be created in S‐rich and S‐poor glass‐ceramics, respectively, while all GeS, Ga₂S₃, and GeS₂ crystals exist in chemically stoichiometric glass‐ceramics. Moreover, we demonstrated the homogeneous distribution of the crystals can be formed in the S‐rich glass‐ceramics from the surface to the interior via composition designing. The present approach blazes a new path to control the growth of the different crystals in chalcogenide glass‐ceramics.     

Influence of the availability of calcium on the hydration of tricalcium aluminate (C3A) in seawater-mixed C3A–gypsum system

This work examined the effects of seawater (SW) on the hydration of tricalcium aluminate (C₃A) in C₃A–gypsum and C₃A–gypsum–Ca(OH)₂ systems through the characterization of hydration heat release, the evolution of aqueous phase composition and hydration products with the hydration time. It was found that SW increased the dissolution driving force of C₃A and solubility of gypsum, which accelerated the early hydration of C₃A and the formation of ettringite (AFt), leading to a higher hydration degree of C₃A at an early age compared with the deionized (DI) water–mixed pastes. After gypsum depletion to form AFt, and in the absence of Ca(OH)₂, the formation of chloroaluminate hydrates was slower due to the insufficient Ca resulted in an accumulation of Al in solution. This would delay the subsequent transformation of AFt to monosulfate (SO₄–AFm) and the formation of hydrogarnet (C₃AH₆), which would further reduce the hydration degree of the C₃A at the later ages. However, in the presence of Ca(OH)₂, the hydration degree of C₃A–gypsum–Ca(OH)₂ at later ages was increased, which was similar to that of the corresponding DI pastes. This can be inferred that the amount of Ca available in SW-mixed cement concrete can affect the hydration degree of C₃A in cement.     

Early age hydration and pozzolanic reaction in natural zeolite blended cements: Reaction kinetics and products by in situ synchrotron X-ray powder diffraction

The in situ early-age hydration and pozzolanic reaction in cements blended with natural zeolites were investigated by time-resolved synchrotron X-ray powder diffraction with Rietveld quantitative phase analysis. Chabazite and Na-, K-, and Ca-exchanged clinoptilolite materials were mixed with Portland cement in a 3:7 weight ratio and hydrated in situ at 40 °C.The evolution of phase contents showed that the addition of natural zeolites accelerates the onset of C₃S hydration and precipitation of CH and AFt. Kinetic analysis of the consumption of C₃S indicates that the enveloping C–S–H layer is thinner and/or less dense in the presence of alkali-exchanged clinoptilolite pozzolans. The zeolite pozzolanic activity is interpreted to depend on the zeolite exchangeable cation content and on the crystallinity. The addition of natural zeolites alters the structural evolution of the C–S–H product. Longer silicate chains and a lower C/S ratio are deduced from the evolution of the C–S–H b-cell parameter.     

Impact of Annealing on the Early Hydration of Tricalcium Silicate

It was recently proposed that the induction period observed during the hydration of tricalcium silicate could be explained by the build‐up of ions in solution. Due to the importance of defects in this mechanism, this work describes the effect of different annealing effects on the defect structure and hydration behavior of C₃S. The impact of annealing on the crystal structure was checked by X‐ray diffraction and the defect structure studied by transmission electron microscopy. The hydration kinetics were followed by isothermal calorimetry of pastes. Scanning electron microscopy was used to look at the microstructure formation. It was observed that grinding created a highly deformed layer on the surface of the grains, which disappeared after annealing. The defect structure was closely related to the length of the induction period observed in pastes by calorimetry. There was no observable effect on the morphology of C–S–H during hydration, but the number of calcium hydroxide nuclei was less in pastes from annealed material.     

Simultaneous study of mechanical property development and early hydration chemistry in Portland cement slurries using X-ray diffraction and ultrasound reflection

A sample cell for the simultaneous measurement of synchrotron X-ray powder diffraction and ultrasound shear-wave reflection data from cement slurries is described. White cement slurries at 25 and 50 °C with 0–3% bwoc CaCl₂ were studied to illustrate the potential of the apparatus. The decrease in reflected S-wave amplitude, in dB, showed a linear correlation with C₃S hydration. CaCl₂ retarded the development of G′ and G″ relative to the extent of C₃S hydration. At short times, there was a correlation between the time evolution of both G′ and G″, and the amount of precipitated CH seen by diffraction, which was almost independent of CaCl₂ concentration and temperature. CaCl₂ addition resulted in a decrease in the amount of CH visible to X-rays, relative the degree of C₃S hydration. This may indicate a change in C–S–H gel C:S ratio or the presence of nanoscale CH that could not be seen by diffraction.     

Physicochemical effects of nanosilica on C3A/C3S hydration

In this paper, C₃A-gypsum and C₃A-C₃S-gypsum model cement systems with and without nanosilica were studied. The effects of nanosilica on the early stage cement hydration, particularly C₃A hydration, were assessed through the heat of hydration (isothermal calorimetry), phase assemblage (quantitative X-ray diffraction), zeta potential, ion concentration measurements, and morphology (scanning electron microscopy) examinations. The results indicate that while promoting C₃S hydration, nanosilica retarded C₃A hydration in both the systems studied. The retardation was caused by the adsorption and coverage of nanosilica on C₃A surfaces through the electrostatic interaction, thus decreasing the C₃A dissolution rate and hindering the precipitation of hydration products. Consequently, the reduced gypsum consumption rate and the seeding effect of nanosilica further promoted C₃S hydration. These findings suggest that nanosilica and other silica-based nanoparticles can physicochemically influence hydration of cement-based materials, and a better understanding of these influencing mechanisms can help optimize performances of nanoparticle-modified cement-based materials.     

Acid Corrosion Behavior of Sol–Gel‐Prepared Mullite Ceramics With and Without Addition of Lanthanum

The corrosion behavior of pure and lanthanum doped, sol – gel‐derived, mullite ceramics in nitric acid aqueous solutions with various concentrations was investigated and compared. Samples sintered at a temperature of 1600°C for 4 h were characterized using powder X‐ray diffraction, SEM, and energy dispersive X‐ray spectroscopy. The corrosion behavior was explored by measuring the amount of eluted ions using atomic absorption spectrophotometry and inductively coupled plasma optical emission spectrometry (ICP‐OES). The doped sample was found to be more susceptible to dissolution in the corrodent, having higher leaching rates. The amounts of eluted lanthanum ions were in order of magnitude higher than amounts of silicon and aluminum. Those phenomena were attributed to the incorporation of lanthanum in the glassy phase, forming SiO₂ – La₂O₃‐rich glassy phase, which can dissolve in corrodent more easily than SiO₂‐rich glassy phase in the pure sample.     

New thermochromic liquid–crystalline polymer: Synthesis and phase behavior

A series of new thermochromic side‐chain liquid–crystalline polymers were prepared. The chemical structures of the resulting monomers and polymers were characterized by element analyses, FTIR, ¹H‐NMR, and ¹³C‐NMR. Their mesogenic properties were investigated by differential scanning calorimetry, thermogravimetric analyses, polarizing optical microscopy, and X‐ray diffraction measurements. The influence of the content of dye groups on phase behavior of the polymers was discussed. The polymers P₁–P₃ showed smectic phase, and P₄–P₇ revealed cholesteric phase. The polymers containing less than 30 mol % of the dye groups showed good solubility, reversible phase transition, wider mesophase temperature ranges, and higher thermal stability. Experimental results demonstrated that the clearing temperature and mesophase temperature ranges decreased with increasing the concentration of the dye groups. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 329–335, 2005     

Phase Evolution of SiO2–Al2O3–ZnO–CaO–ZrO2–TiO2‐Based Glass with Added Y‐PSZ Particles

Yttria partially stabilized zirconia Y‐PSZ/glass‐ceramic composites were prepared by reaction sintering using powder mixtures of a SiO₂–Al₂O₃–ZnO–CaO–ZrO₂–TiO₂‐based glass and yttria partially stabilized zirconia (Y‐PSZ). The glass crystallized during sintering at temperatures of 1173, 1273, and 1373 K to give a glass‐ceramic matrix for high‐temperature protecting coatings. With the increasing firing time, the added zirconia reacted with the base glass and a glass‐ceramic material with dispersed zircon particles was prepared in situ. Furthermore, the added zirconia changed the crystallization behavior of the base glass, affecting the shape, amount, and distribution of zircon in the microstructure. The bipyramid‐like zircon grains with imbedded residual zirconia particles turned out to have two growth mechanisms: the inward growth and the outward growth, and its rapid growth was mainly dominated by the later one. For comparison, the referenced glass‐ceramic was prepared by sintering using exclusive glass granules and its crystallization behavior at 1173–1373 K was examined as well. Scanning electron microscopy (SEM), energy dispersive X‐ray spectroscopy (EDS), transmission electron microscopy (TEM), and X‐ray diffraction (XRD) were used to characterize the crystallization behavior of the base glass and the phase evolution of the Y‐PSZ/glass‐ceramic composites.     

Subsolidus Phase Relationship in the CaO–CuO–TiO2 Ternary System at 950°C in Air

The subsolidus phase relationship in the CaO–CuO–TiO₂ ternary system at 950°C in air was investigated. Total 26 samples having various nominal compositions were prepared by the solid‐state reaction at 950°C in air, and their equilibrium phases were analyzed by powder X‐ray diffraction (XRD). The CaCu₃Ti₄O₁₂ phase exhibits variable stoichiometry and forms as the Ca_1?xCu_3+xTi₄O₁₂‐type (?0.019 ≤x ≤0.048) solid solution at 950°C in air. On the basis of our results and previous reports on the binary phase diagrams, the subsolidus phase diagram of the CaO–CuO–TiO₂ ternary system could be constructed at 950°C in air.