Water Corrosion of YBa2Cu3O7−δ Superconductors

Solid-state sintering was used to make YBa₂Cu₃O_7−δ superconducting bulk materials. Corrosion of the YBa₂Cu₃O_7−δ superconductor material was investigated in a humid environment. The superconducting materials exhibited significant corrosion after 4 h at 80° and 100% relative humidity. A grain-boundary phase was formed, and the percent superconducting phase in the material decreased by approximately 60%. The transition temperature (T_c) decreased with corrosion time. After 2 h of corrosion, T_c decreased from 87 to 81 K.     

Hot Isostatic Pressing of YBa2Cu3O7-δ and YBa2Cu3O7–δ/Ag Composites

Hot isostatic pressing (HIP) can be used to produce fully dense shapes of high-temperature ceramic superconductors. Densification modeling of monolithic YBa₂Cu₃O_7-δ and the composite YBa₂Cu₃O_7-δ/Ag systems allows an understanding of the HIP process and has led to the development of successful protocols for HIP of these materials. Ag metal is the best encapsulation material found for both systems. HIP of monolithic YBa₂Cu₃O_7-δ requires a slow ramp of pressure in order to prevent decomposition into more basic oxides such as Y₂BaCuO₅ and CuO. HIP of composite YBa₂Cu₃O_7-δ/Ag requires careful powder processing to obtain dense material with a fine dispersion of Ag.     

Hot Deformation of YBa2Cu3O7-δ and Composite YBa2Cu3O7-δ/Ag

The response of ceramic superconductors and ceramic composites to compressive stresses at high temperatures has been examined. Monolithic YBa₂Cu₃O_7-δ and composite YBa₂Cu₃O₇-δ₆/Ag were tested at constant true strain rates from 10^-6 to 10^-3 s^-1 at temperatures from 800° to 950°C. Fine-grained monolithic YBa₂Cu₃O_7-δ appears to have a regime of superplastic deformation between temperatures of 850° and 950°C at strain rates from 10^-6 to 10^-4 S^-1. The addition of 20 vol% Ag to a coarser-grained material enhances the ductility of the ceramic and lowers the flow stress by a factor of 3 to 10. However, there is no evidence of superplasticity in the composite material in the range of temperature and strain rate where it was tested.     

Epitaxial Solution Deposition of YBa2Cu3O7−δ-Coated Conductors

A variety of solution deposition routes have been reported for processing complex perovskite-based materials such as ferroelectric oxides and conductive electrode oxides, due to ease of incorporating multiple elements, control of chemical stoichiometry, and feasibility for large area deposition. Here, we report an extension of these methods toward long length, epitaxial film solution deposition routes to enable biaxially oriented YBa₂Cu₃O_7−δ (YBCO)-coated conductors for superconducting transmission wires. Recent results are presented detailing an all-solution deposition approach to YBCO-coated conductors with critical current densities J _c (77 K)>1 MA/cm² on rolling-assisted, biaxially textured, (200)-oriented Ni–W alloy tapes. Solution-deposition methods such as this approach and those of other research groups appear to have promise to compete with vapor phase methods for superconductor electrical properties, with potential advantages for large area deposition and low cost/kA·m of wire.     

Effect of Oxygen Loss on Densification When Hot Isostatic Pressing YBa2Cu3O7−δ

Hot isostatic pressing of the high-T_c superconductor YBa₂Cu₃O_7−δ can lead to loss of oxygen and transformation of the material from the high-T_c orthorhombic phase to the nonsuperconducting tetragonal phase. It is shown that glass encapsulation helps retain the orthorhombic structure, whereas steel encapsulation resulted in formation of the tetragonal phase. Reasons for this phenomenon are discussed. The equilibrium oxygen gas pressure for the oxygen decomposition reaction in YBa₂Cu₃O₇, however, prevents full densification of this material in glass when employing hot isostatic pressing conditions of 200 MPa and 845°C.     

Local Dendrite Development during Seeded Peritectic Solidification of Large YBa2Cu3O7−δ Grains

The growth morphology of large YBa₂Cu₃O_7−δ grains during peritectic solidification has been reported to be responsible for the generation of processing defects, such as platelets, and an inhomogeneous distribution of 211 particles, both of which influence significantly the superconducting properties of the fully processed material. The present study demonstrates both experimentally and theoretically the formation of local dendrites at macroscopically planar YBa₂Cu₃O_7−δ growth fronts which propagate along different crystallographic directions and identifies these as key growth features of the peritectic solidification process.     

Reaction of YBa2Cu3O7-δ Powder with NOx Gas in an Aerosol Reactor

Thermodynamic calculations predict, and experiments verify, that YBa₂Cu₃O₇-₈ (123) powder is unstable in the presence of NO_x-containing aerosol reactor exhaust gases at temperatures below about 600°C. Powders collected above the stability temperature are single-phase 123, while powders collected at lower temperature contain Ba(NO₃)₂ formed by reaction of the powder with NO_x, after exit from the hot zone.     

The Use of Nitrogen Dioxide to Improve the Superconducting Properties of YBa2Cu3O7

The elemental homogeneity of YBa₂Cu₃O₇ powders can be improved substantially by heating the powder in a nitrogen dioxide-containing atmosphere (e.g., 950°C), followed by annealing in oxygen above 750°C, and slow cooling to room temperature. The improved homogeneity results in a substantially larger flux exclusion signal for the NO₂-treated powder, as measured by ac susceptibility. Moreover, the NO₂-processed powder exhibits a slablike morphology which should be more suitable for grain alignment. A substantial advantage of the NO₂ process is that this process is easily scaled to larger batches and the results are highly reproducible. This is not the case for solid-state reaction processes requiring repeated heating and grinding. The experimental results suggest a mechanism which involves the formation of a small amount of molten Ba(NO₃)₂ which acts as a flux that dissolves the constituents and reprecipitates them as highpurity YBa₂Cu₃O₇. The effects of the various process variables on the properties of the treated powder, and the reproducibility of the process, are discussed.     

Superconductive Properties of the YBa2Cu4O8 Superconductor

A bulk density of 85% of the theoretical density was achieved by sintering a powder compact of YBa₂Cu₄O₈ (124) at 850°C in flowing oxygen at 1 atm (≅10⁵ Pa). This value is very close to that obtained by the hot isostatic pressure technique (90%). The superconducting properties of the sample were characterized by magnetization and ac susceptibility techniques. The magnetization critical current density at 20 K in zero field was determined to be ∼5 × 10⁴ A/cm², and the superconducting transition temperatures were found to be 77 K for the bulk material and 82 K for the granular phase. The powder X-ray diffraction and ac susceptibility studies revealed the sintered 124 material to be single phase.     

Effects of Inclusions on the Sintering Behavior of YBa2Cu3O6+x

The sintering behavior of two types of heterogeneous compacts of YBa₂Cu₃O_{6+ x} was studied: (1) Soft agglomerates present in the starting powder were used to study the effect of rapidly densifying inclusions on the overall sample densification. In this case, the induced stresses caused severe cracklike damage in the sintered microstructure. (2) On the other hand, when nondensifying inclusions (same composition) were incorporated into the starting powder, no sintering damage was observed. Further, there was no retardation of densification or coarsening due to the presence of these dense inclusions, over a wide range of inclusion size. Several possibilities for this behavior are discussed, based on the distribution of stresses induced by differential sintering rates.     

Influence of Iron Doping on the Microstructure of YBa2(Cu1−xFex)3O7−δ Ceramics

Porosity, grain growth, phase composition, and microstructural defects were studied in sintered YBa₂ (Cu_1−x)₃O_7−x ceramics for x values up to 0.3. The porosity of the samples, related to the sintering mechanism, was independent of iron concentration. A linear dependence of the grain size with the inverse of the iron concentration was found, strongly suggesting grain boundary segregation of iron. The solubility limit was estimated to be x = 0.18 at 950°C in O₂. Beyond this limit, a new microstructural component was found consisting of YBa₂(Cu_1−xFe_x)₃O_7−δ, YBaCuFeO₅ and Ba(Cu,Fe)O₂. The transition from an orthorhombic twin to an orthorhombic tweed phase and a tetragonal phase was detected by polarized light microscopy.     

Superplastic Deformation in Fine-Grained YBa2Cu3O7−x

The superplastic behavior of YBa₂Cu₃O_{7− x} ceramic superconductors was studied. Large compressive deformation over 100% strain was measured in the temperature range of 775°–875°C, with a strain rate of 1 × 10⁻⁵ to 1 × 10⁻³/s, and a grain size of 0.5–1.4 μm. The nature of the deformation was investigated in terms of three deformation parameters: the stress exponent ( n ), the grain size exponent ( p ), and the activation energy ( Q ). The measured values of these parameters were n = 2 ± 0.3, p = 2.7 ± 0.7, and Q = 745 ± 100 kJ/mol. With the aid of the deformation map, the deformation mechanism was identified as grain boundary sliding accommodated by grain boundary diffusion. The conclusion is consistent with the microstructural observations made by SEM and TEM: the invariance of equiaxed grain shape, the absence of significant dislocation activity, no grain boundary second phases, and no significant texture development.     

Processing Dependence of Texture, and Critical Properties of YBa2Cu3O7−δ Films on RABiTS Substrates by a Non-Fluorine MOD Method

YBa₂Cu₃O_{7− δ} (YBCO or Y123) films on rolling-assisted biaxially textured substrates (RABiTS) were prepared via a fluorine-free metallorganic deposition (MOD) through spin coating, burnout, and high temperature anneal. The effects of substrate texture and surface energy of the CeO₂ cap layer were investigated. Except for the commonly accepted key factors, such as the textures of substrate and buffer layers, we found some other factors, for example, the deposition temperature of the cap layer, are also critical to the epitaxial growth of Y123 phase. With the CeO₂ cap layer deposited at relative high temperature of 700°C, a critical current density, J _c, over 1 MA/cm² has been demonstrated for the first time on Ni-RABiTS by a fluorine-free MOD method. Whereas for samples with CeO₂ cap layers deposited at a lower temperature of 600°C, even though XRD data showed a better texture on these buffer layers, texture degradations of YBCO grains under the optimized processing conditions were observed and a lower oxygen partial pressure around 40 ppm was necessary for the epitaxial growth of Y123 phase. As a result, J _c fell to 0.45 MA/cm² at 77 K. The observed phenomena points to the change of surface energy and reactivity of the CeO₂ cap layer with respect to the CeO₂ deposition temperature. In this paper, the YBCO phase diagram was also summarized.     

Novel Solution-Soaking Method for Adding Dopants to YBa2Cu3O7−x to Achieve Higher Sintered Densities

YBa₂Cu₃O_7−x was doped with various metal ions by a new technique in which a pellet (after binder burnout) was soaked in a solution containing the appropriate ions and then dried. The sintered density of the treated pellets depended on the dopant in the solution, and in many cases it was much higher than that obtained for pure YBa₂Cu₃O_7−x (93% to 96% as compared with 85% to 90%). A study of the microstructure revealed that, in those cases where higher sintered densities were obtained, the grain size was much smaller. The grain morphology, however, did not change. It is likely that the high concentration of dopant adsorbed on the grain surface during solution soaking enhanced the rate of sintering.     

High-Temperature Microwave Complex Permittivity of YBa2Cu3O7-δ Superconductors

The high-temperature microwave complex permittivity of YBa₂Cu₃O_7-δ superconductors was characterized using a coaxial probe system designed and built in our laboratory. An anomalous difference in complex permittivity between a green sample and a sintered sample was analyzed with respect to oxygen content being a possible key factor to affect the dielectric properties.     

Vapor Pressure of Barium and Copper Components in YBa2Cu3O7−x Superconductor Ceramics

Purified air is passed over a specimen of YBa₂Cu₃O_{7– x} at 890°C; the vaporized substances are condensed in a pure alumina tube, then subjected to inductively controlled plasma analysis. Vapor pressure values of 2.5 × 10⁻⁵ Pa for BaO( g ), 1.2 × 10⁻⁴ Pa for Cu( g ), and 2.2 × 10⁻⁵ Pa for CuO( g ) are obtained under 2.1 × 10⁴ Pa (0.21 bar) of oxygen pressure. No Y vapor is detected at this temperature.     

Transmission Electron Microscopy Study on the Annealing of YBa2Cu3O7-δ

Annealing in oxygen-rich atmosphere at temperatures between 400° and 600°C is an important step in the manufacture of superconducting YBa₂Cu₃O_7-δ. The symmetry of the orthorhombic phase requires that if more than one type of twin plane is present within a grain, a distorted region should exist inside the multiple twinned grain. This distorted region hinders the tetragonal-to-orthorhombic transformation and may account for some retained tetragonal phase inside an otherwise orthorhombic grain. A physical model is presented describing the formation of such regions and their eventual transformation into low-angle grain boundaries after long annealing. Extended annealing at intermediate temperatures apparently leads to the formation of planar faults in off-stoichiometric samples. Transmission electron microscope image contrast and energy dispersive X-ray analyses of highly defective regions suggest these defects are CuO _x ( x = 1, 2) extra layers. These extra layers tend to form near grain boundaries or free surfaces, where oxygen is readily available.     

Thermopower of YBa2Cu3O7-δ–Ag Composites

The percolation behavior of normal-state thermopower, resistivity, and superconductivity have been studied in YBa₂Cu₃O_7-δ─Ag (YBCO─Ag) composite systems. The normal-state resistivity and thermopower show a percolation threshold at a Ag volume fraction ( V _Ag) of 20% to 30%, whereas the superconducting network shows a threshold at a V _Ag of ≅70% to 80%. The results obtained from this study show that the YBCO─Ag composite obtained from Ag₂O and YBCO powders is uniformly distributed with Ag and YBCO remaining as separate phases without changing their characteristics. The measurements of thermopower indicate that the normal-state thermopower and phonon-drag thermopower are affected by the Ag addition. The stability of YBCO is increased when it is in composite form.     

Superconductivity in the (Yba2Cu3)1−xNaxO7−δ System

The (YBa₂Cu₃)_1−xNa_xO_7–δ system in the range of x = 0–0.8 was investigated. Experimental data suggest that the sodium doping with x 0.26 does not affect the critical transition temperature T_c, and the crystal structure maintains the orthorhombic lattice with a slightly smaller unit cell. However, sodium doping increases the sintering and grain growth kinetics, resulting in a higher superconducting phase volume and an enhanced Meissner effect. It also lowers the processing temperaturel. The experimental data also suggest that the sodium atoms diffuse into the superconducting YBa₂Cu₃O_7−δ crystallites, which stabilizes the orthorhombic phase. The transition temperature (ortho-rhombic to tetragonal) in sodium-doped materials increases with the increasing concentration of sodium.