Pressureless Sintering of ZrB2 Prepared by Colloidal Processing: Particle Packing,Sintering Conditions,and Additives

Nonaqueous colloidal processing in cyclohexane and slip casting allowed the preparation of green ZrB₂ compacts with 67.3% TD (theoretical density), which upon pressureless sintering at 2100°C densified to a final density of 92.4% TD. The effect of controllable sintering parameters (temperature, time, and heating rate) on the sintered properties of ZrB₂ compacts prepared using the nonaqueous colloidal processing method was also studied, to maximize the sintered density and tailor the desired microstructure (i.e., dense final object with small grain size). The competition between pore elimination and grain growth mainly controls the final density achievable. ZrB₂ compacts with maximum sintered densities of 93% TD could be achieved by controlling the sintering conditions. Finally, the use of carbon and B₄C additives to improve the sintered density and microstructure of ZrB₂ compacts was also investigated. The additives, compatible with colloidal processing, allowed compacts with greater sintered densities (96–98% TD) and finer grain sizes to be achieved by pressureless sintering, even at a lower temperature of 1900°C.     

Elevated Temperature Strength Enhancement of ZrB2–30 vol% SiC Ceramics by Postsintering Thermal Annealing

The mechanical properties of dense, hot‐pressed ZrB₂–30 vol% SiC ceramics were characterized from room temperature up to 1600°C in air. Specimens were tested as hot‐pressed or after hot‐pressing followed by heat treatment at 1400°C, 1500°C, 1600°C, or 1800°C for 10 h. Annealing at 1400°C resulted in the largest increases in flexure strengths at the highest test temperatures, with strengths of 470 MPa at 1400°C, 385 MPa at 1500°C, and 425 MPa at 1600°C, corresponding to increases of 7%, 8%, and 12% compared to as hot‐pressed ZrB₂–SiC tested at the same temperatures. Thermal treatment at 1500°C resulted in the largest increase in elastic modulus, with values of 270 GPa at 1400°C, 240 GPa at 1500°C, and 120 GPa at 1600°C, which were increases of 6%, 12%, and 18% compared to as hot‐pressed ZrB₂–SiC. Neither ZrB₂ grain size nor SiC cluster size changed for these heat‐treatment temperatures. Microstructural analysis suggested additional phases may have formed during heat treatment and/or dislocation density may have changed. This study demonstrated that thermal annealing may be a useful method for improving the elevated temperature mechanical properties of ZrB₂‐based ceramics.     

Reactive hot pressing route for dense ZrB2-SiC and ZrB2-SiC-CNT ultra-high temperature ceramics

The in-situ exothermic reactions between ZrC_0.8, B₄C and Si have assisted densification and allowed to obtain fully dense ZrB₂-31 wt.%SiC ultra-high temperature ceramics within 6 min at 1750 °C. The use of zirconium carbide instead of metallic zirconium in the green body obviated the possibility of in-situ SHS process and allowed to apply the pressure at low temperatures. The latter provided a first densification stage just above 1050 °C. A slight carbon excess was created in the green body to preserve the carbon nanotubes. The developed reactive hot pressing route (1830 °C, 3 min, 30 MPa) has been successfully used to obtain ZrB₂-SiC ceramics containing 8 vol.% of multi-wall carbon nanotubes (MW-CNT). The carbon nanotubes survived the thermal cycle and could be clearly observed in the sintered ceramics. The CNT addition improved the fracture toughness of the composite from 4.3 MPa m^1/2 for ZrB₂-31 wt.%SiC to 6.8 MPa m^1/2 for ZrB₂-29 wt.%SiC-CNT.     

Sintering behavior of ZrB2–SiC composites doped with Si3N4: A fractographical approach

ZrB₂–SiC composite ceramics were doped with 0, 1, 3 and 5 wt% Si₃N₄ plus 1.6 wt% carbon (pyrolized phenolic resin) as sintering aids and fabricated by hot pressing process under a relatively low pressure of 10 MPa at 1900 °C for 2 h. For a comparative study, similar ceramic compositions were also prepared by pressureless sintering route in the same processing conditions, with no applied external pressure. The effect of silicon nitride dopant on the microstructural evolution and sintering process of such ceramic composites was investigated by a fractographical approach as well as a thermodynamical analysis. The relative density increased by the addition of Si₃N₄ in hot pressed samples as a fully dense composite was achieved by adding 5 wt% silicon nitride. A reverse trend was observed in pressureless sintered composites and the relative density values decreased by further addition of Si₃N₄, due to the formation of gaseous products which resulted in the entrapment of more porosities in the final structure. The formation of ZrC phases in pressureless sintered samples and layered BN structures in hot pressed ceramics was detected by HRXRD method and discussed by fractographical SEM-EDS as well as thermodynamical analyses.     

Fabrication of ZrB2 ceramics by reactive hot pressing of ZrB and B

Zirconium diboride (ZrB₂) ceramics were prepared by reactive hot pressing of ZrB+B powder mixture. Formation of a transient liquid due to eutectic reaction of ZrB₂+Zr→L_eu(ZrB2+Zr) at 1661°C following peritectic decomposition of 2ZrB=ZrB₂+Zr at 1250°C during heating up of the ZrB+B mixture facilitated densification. The liquid phase was subsequently eliminated via reaction of B with Zr in the eutectic liquid L_eu(ZrB2+Zr) to result in a dense ZrB₂ ceramic. Full density was reached after reactive hot pressing at 1900°C under 30 MPa for 1 h. The ZrB₂ ceramic had a refined microstructure consisting of grains of <1.5 μm in size and relatively good Vickers hardness (21 ± 2 GPa) and flexural strength (595 ± 63 MPa).     

Reactive hot pressing of ZrB2-based composites with changes in ZrO2/SiC ratio and sintering conditions. Part I: Densification behavior

ZrB₂–SiC–ZrO₂ composites were hot pressed in order to investigate the effects of adding nano-sized ZrO₂ particles as well as the hot pressing parameters on the densification behavior of ZrB₂–SiC composites. An L9 orthogonal array of the Taguchi method was employed to study the significance of each parameter such as the sintering temperature, time, the applied external pressure, and ZrO₂/SiC volume ratio on the densification process. The statistical analyses revealed that among the mentioned parameters, the hot pressing temperature had a great influence over the densification. By being hot pressed at 1850 °C for 90 min under 16 MPa, fully dense ZrB₂-based composites were obtained. The relative density of the composites decreased at first and then enhanced as a function of ZrO₂/SiC ratio. Microstructural investigation of the fracture surfaces of the composites, which was carried out using the SEM analysis, showed the formation of new phases on the surfaces of SiC grains. The EDS and XRD analyses identified the ZrC as the newly formed interfacial phase due to the reaction between nano-ZrO₂ and SiC. The ZrC acted as an adhesive interphase between the ZrB₂/SiC grains, which could assist the sintering process.     

Densification of ZrB2-based composites and their mechanical and physical properties: A review

This study reviews densification behaviour, mechanical properties, thermal, and electrical conductivities of the ZrB₂ ceramics and ZrB₂-based composites. Hot-pressing is the most commonly used densification method for the ZrB₂-based ceramics in historic studies. Recently, pressureless sintering, reactive hot pressing, and spark plasma sintering are being developed. Compositions with added carbides and disilicides displayed significant improvement of densification and made pressureless sintering possible at ≤2000 °C. Reactive hot-pressing allows in situ synthesizing and densifying of ZrB₂-based composites. Spark plasma sintering displays a potential and attractive way to densify the ZrB₂ ceramics and ZrB₂-based composites without any additive. Young's modulus can be described by a mixture rule and it decreased with porosity. Fracture toughness displayed in the ZrB₂-based composites is in the range of 2–6 MPa m^1/2. Fine-grained ZrB₂ ceramics had strengths of a few hundred MPa, which increased with the additions of SiC and MoSi₂. The small second phase size and uniform distribution led to higher strengths. The addition of nano-sized SiC particles imparts a better oxidation resistance and improves the strength of post-oxidized ZrB₂-based ceramics. In addition, the ZrB₂-based composites showed high thermal and electrical conductivities, which decreased with temperature. These conductivities are sensitive to composition, microstructure and intergranular phase. The unique combinations of mechanical and physical properties make the ZrB₂-based composites attractive candidates for high-temperature thermomechanical structural applications.     

Chemical process and solid solution formation in reactive hot pressed ZrB2–SiC ceramics doped with W

ZrB₂–SiC doped with W was prepared from a mixture of Zr, Si, B₄C and W via reactive hot pressing. The fully dense ZrB₂–SiC–WB–ZrC ceramic was obtained at 1900°C for 60 min under 30?MPa in an argon atmosphere. Reaction path and solid solution characteristics of the starting powders were studied through a series of pressureless heat treatment at temperatures between 700 and 1500°C. The solid solution phases of (Zr, W)B₂, (W, Zr)B and (Zr, W)C were formed directly by reactions between the precursors. Homogeneous distribution of solute atoms in solution and the solid solubilities were also studied.     

Sintering Mechanisms and Kinetics for Reaction Hot‐Pressed ZrB2

Sintering mechanisms and kinetics were investigated for ZrB₂ ceramics produced using reaction hot pressing. Specimens were sintered at temperatures ranging from 1800°C to 2100°C for times up to 120 min. ZrB₂ was the primary phase, although trace amounts of ZrO₂ and C were also detected. Below 2000°C, the densification mechanism was grain‐boundary diffusion with an activation energy of 241 ± 41 kJ/mol. At higher temperatures, the densification mechanism was lattice diffusion with an activation energy of 695 ± 62 kJ/mol. Grain growth exponents were determined to be ~4.5, which indicated that a grain pinning mechanism was active in both temperature regimes. The diffusion coefficients for grain growth were 1.5 × 10^?16 cm⁴/s at 1900°C and 2.1 × 10^?15 cm⁴/s at 2100°C. This study revealed that dense ZrB₂ ceramics can be produced by reactive hot pressing in shorter times and at lower temperatures than conventional hot pressing of commercial powders.     

Fabrication of transparent MgAl2O4 ceramics by gelcasting and cold isostatic pressing

Highly transparent MgAl₂O₄ ceramics have been fabricated by aqueous gelcasting combined with cold isostatic pressing (CIP), pressureless sintering and hot isostatic pressing (HIP) from high purity spinel nanopowders. The gelling system used AM and MABM as monomer and gelling agent. The influences of dispersant and PH on the rheological behavior of the MgAl₂O₄ slurries were investigated. The spinel slurry with low solids loading (25 vol%) and low viscosity (0.15 Pa s) was obtained by using 6 wt% Duramax-3005 (D-3005) as dispersant. After CIP, the green body had a relative density of 48% with a narrow pore size distribution. The influence of sintering temperature on densification and microstructure was studied, choosing 1500 °C as the sintering temperature. After HIP (1650 °C/177 MPa/5 h), transparent MgAl₂O₄ ceramic with the thickness of 3 mm was obtained, whose in-line transmittance was 86.4% at 1064 nm and 79.8% at 400 nm, respectively. The ceramic exhibited a dense microstructure with the average grain size of 23 μm. The Vickers hardness and flexure strength of the sample reached 13.6 GPa and 214 MPa, respectively.     

Microstructure and mechanical properties of carbon-precursor-added B4C and B4C−SiC ceramics subjected to pressureless sintering

Organic-carbon-precursor-added B₄C and B₄C–SiC ceramics were subjected to pressureless sintering at various temperatures. The carbon precursor increased the densification of the B₄C and B₄C–SiC ceramics sintered at 2200 °C to 95.6 % and 99.1 % theoretical density (T.D.), respectively. The pyrolytic carbon content of the B₄C–SiC composite decreased with increasing SiC content. The graphitization degree of pyrolytic carbon decreased slightly with the amount of carbon precursor and content of SiC. The 95 wt. % B₄C–5 wt. % SiC composite added with 7.5 wt. % carbon precursor and sintered at 2200 °C outperformed the other B₄C–SiC composites, and its sintered density, flexural strength, Young’s modulus, and microhardness were 98.6 % T.D., 879 MPa, 415 GPa, and 28.5 GPa, respectively. These values were higher than those of composites prepared via pressureless sintering and comparable to those of composites fabricated via hot pressing and/or using metal or oxide additives.     

Effect of Sintering Temperature on Thermoelectric Properties of p‐Bi2Te3 Alloys Produced by Gas Atomization

In this research, p‐type Bi₂Te₃–75% Sb₂Te₃ thermoelectric alloy powders were produced by gas atomization and subsequently sintered by hot pressing at different temperatures. The grain growth of the hot‐pressed samples was observed with increasing sintering temperature from 380°C to 460°C. The compressive strength increased with increasing hot‐pressing temperature due to the high relative density of bulk samples obtained at high temperatures. The effect of sintering temperature on thermoelectric (TE) properties was studied. The maximum power factor 3.48 mW/mK² was obtained for the sample hot pressed at 420°C due to the resulting high electrical conductivity and enhanced Seebeck coefficient values.     

Synergetic effects of SiC and Csf in ZrB2-based ceramic composites. Part I: Densification behavior

The effects of processing variables on densification behavior of hot pressed ZrB₂-based composites, reinforced with SiC particles and short carbon fibers (C_sf), were studied. A design of experiment approach, Taguchi methodology, was used to investigate the characteristics of ZrB₂–SiC–C_sf composites concentrated upon the hot pressing parameters (sintering temperature, dwell time and applied pressure) as well as the composition (vol% SiC/vol% C_sf). The analysis of variance recognized the sintering temperature and SiC/C_sf ratio as the most effective variables on the relative density of hot pressed composites. The microstructural investigations showed that C_sf can act as a sintering aid and eliminate the oxide impurities (e.g. B₂O₃, ZrO₂ and SiO₂) from the surfaces of raw materials. A fully dense composite was achieved by adding 10 vol% C_sf and 20 vol% SiC to the ZrB₂ matrix via hot pressing at 1850 °C for 30 min under a pressure of 16 MPa. Moreover, the in-situ formation of interfacial ZrC, which also improves the sinterability of ZrB₂-based composites, was studied by energy-dispersive X-ray spectroscopy analysis and verified thermodynamically.     

Pressureless sintering of Al2O3 containing up to 20 vol% zirconium diboride (ZrB2)

The production of particle composites by means of pressureless sintering provides a cost-effective alternative to production variants such as hot-pressing. However, minimal quantities of additives are sufficient to impede the densification of oxidic matrix components. This paper examines the sintering behaviour of alumina powder as a function of the volume fraction of ZrB₂ (up to 20 vol%). A distinction can be made between two sintering ranges according to the temperature: at T⩽1700° a solid-state process applies. This process is decisively influenced by the boron oxide (B₂O₃) contained in the raw material ZrB₂. The validity of the Lange model, which describes the influence of increasing volumes of inclusions on the densification behaviour of a crystalline matrix phase, is confirmed in this temperature range. At T>1700°C, an aluminium borate melt occurs, accelerating the sintering process substantially. As a result, the composites quickly attain matrix densities greater than 95% of the theoretical density. At higher firing temperatures the ZrB₂ particles coalesce, resulting in the formation of an electrically conductive penetration structure at a content level of 20 vol%.     

Reactive sintering behavior and enhanced densification of (Ti,Zr)B2–(Zr,Ti)C composites

Reactive hot pressing was used to prepare (Ti,Zr)B₂–(Zr,Ti)C composites from equimolar ZrB₂ and TiC powders. The reaction and solid-solution coupling effect and enhanced densification in ZrB₂-50 mol.% TiC were proposed as contrasted to conventional consolidation of TiB₂-50 mol.% ZrC. The (Ti,Zr)B₂–(Zr,Ti)C composite sintered at a temperature as low as 1750 °C exhibited negligible porosity and average grain sizes of 0.30 μm for (Ti,Zr)B₂ and 0.36 μm for (Zr,Ti)C. Complete reaction and rapid densification of ZrB₂-50 mol.% TiC was achieved at 1800 °C for only 10 min. The densification mechanism was mainly attributed to material transport through lattice diffusion of Ti and Zr atoms with an activation energy of 531 ± 16 kJ/mol. This study revealed for the first time novel insights into rapid densification of refractory fine-grained diboride–carbide composites by reactive hot pressing at relatively low temperatures.     

Zirconium diboride laminates for improved damage tolerance at elevated temperatures

The mechanical response was studied for dense laminates containing layers of ZrB₂ (~145 µm) and graphite—10 vol% ZrB₂ (~20 µm). Individual layers were formulated by mixing starting powders with thermoplastic polymers and pressing into sheets. Laminates were produced by stacking and warm pressing the sheets, debinding, and hot pressing at 2050°C, 32 MPa, in Ar. The laminates were fractured at temperatures up to 2000°C in Ar. Laminates exhibited room temperature flexure strength of 260 MPa, increasing to 300 MPa at 1600°C, and then decreasing to 160 MPa at 2000°C. Inelastic work of fracture was 0.6 kJ/m² at room temperature, reached a maximum of 1.3 kJ/m² at 1400°C, and reverted to linear elastic failure at 2000°C. During fracture, cracks were deflected at the interfaces between the strong ZrB₂ layers and the relatively weak C-ZrB₂ layers, which led to an increased inelastic work of fracture by more than an order of magnitude compared to conventional ZrB₂ ceramics. This study demonstrated that laminate architectures are a promising approach for improving the damage tolerance of ZrB₂-based ceramics at elevated temperatures.     

Processing,microstructure, and mechanical properties of hot-pressed ZrB2 ceramics with a complex Zr/Si/O-based additive

Densification behavior, microstructure, and mechanical properties of zirconium diboride (ZrB₂) ceramics modified with a complex Zr/Si/O-based additive were studied. ZrB₂ ceramics with 5–20 vol.% additions of Zr/Si/O-based additive were densified to >95% relative density at temperatures as low as 1400°C by hot-pressing. Improved densification behavior of ZrB₂ was observed with increasing additive content. The most effective additive amount for densification was 20 vol.%, hot-pressed at 1400°C (∼98% relative density). Microstructural analysis revealed up to 7 vol.% of residual second phases in the final ceramics. Improved densification behavior was attributed to ductility of the silicide phase, liquid phase formation at the hot-pressing temperatures, silicon wetting of ZrB₂ particles, and reactions of surface oxides. Room temperature strength ranged from 390 to 750 MPa and elastic modulus ranged from 440 to 490 GPa. Vickers hardness ranged from 15 to 16 GPa, and indentation fracture toughness was between 4.0 and 4.3 MPa·m^1/2. The most effective additive amount was 7.5 vol.%, which resulted in high relative density after hot-pressing at 1600°C and the best combination of mechanical properties.     

Reactive hot pressing of zirconium diboride

The reaction of zirconium and boron was investigated as a potential route to form dense monolithic zirconium diboride (ZrB₂) ceramics. Attrition milling of the precursors produced nanosized (less than 100 nm) zirconium metal particles that reacted with boron to form ZrB₂ with an average particle size of less than 100 nm at temperatures as low as 600 °C. Scanning electron microscopy of ZrB₂ compacts heated to 1450 °C and 1650 °C showed average particle sizes of 0.6 μm and 1.0 μm, respectively, suggesting that the fine particle size was maintained during densification. Ceramics with a relative density of 99% were produced by hot pressing at 2100 °C. Dense ZrB₂ produced by the reactive hot pressing process had mechanical properties that were comparable to ceramics produced by conventional processes. The four-point flexure strength of ZrB₂ produced in this study was 434 MPa.     

Synthesis,properties and thermal decomposition of the Ta4AlC3 MAX phase

The present work describes a synthesis route for bulk Ta₄AlC₃ MAX phase ceramics with high phase purity. Pressure-assisted densification was achieved by both hot pressing and spark plasma sintering of Ta₂H, Al and C powder mixtures in the 1200–1650 °C range. The phases present and microstructures were characterized as a function of the sintering temperature by X-ray diffraction and scanning electron microscopy. High-purity α-Ta₄AlC₃ was obtained by hot pressing at 1500 °C for 30 min at 30 MPa. The β-Ta₄AlC₃ allotrope was observed in the samples produced by SPS. The Young’s modulus, Vickers hardness, flexural strength and single-edge V-notch beam fracture toughness of the high-purity bulk sample were determined. The thermal decomposition of Ta₄AlC₃ into TaC_x and Al vapour in high (˜10⁻⁵ mbar) vacuum at 1200 °C and 1250 °C was also investigated, as a possible processing route to produce porous TaC_x components.     

Investigation of hot pressed ZrB2–SiC–carbon black nanocomposite by scanning and transmission electron microscopy

Hybrid ZrB₂-based composite having 10 vol% nano-sized carbon black and 20 vol% SiC was fabricated by vacuum hot pressing at 1850 °C under 20 MPa for 60 min. The microstructure and sinterability of the as-sintered ceramic was studied by X-ray powder diffraction, scanning electron microscopy, X-ray spectroscopy, scanning transmission electron microscopy and transmission electron microscopy analyses. A fully-dense hybrid composite could be achieved by hot pressing method under the aforementioned conditions. No new in-situ phase formation was detected after sintering process. Although the densification progressed in a non-reactive manner, the addition of carbonaceous material assisted the sinterability acting as the surface oxides cleaner. The precise phase and nanostructural investigations of the prepared ceramic verified the partial graphitization of carbon black and conversion of amorphous nano-additive into crystalline graphite nano-flakes.