Porous mullite ceramics with enhanced compressive strength from fly ash-based ceramic microspheres: Facile synthesis,structure, and performance

Porous mullite ceramics are widely used in heat insulation owing to their high temperature and corrosion resistant properties. Reducing the thermal conductivity by increasing porosity, while ensuring a high compressive strength, is vital for the synthesis of high-strength and lightweight porous mullite ceramics. In this study, ceramic microspheres are initially prepared from pre-treated high-alumina fly ash by spray drying, and then used to successfully prepare porous mullite ceramics with enhanced compressive strength via a simple direct stacking and sintering approach. The influence of sintering temperature and time on the microstructure and properties of porous mullite ceramics was evaluated, and the corresponding formation mechanism was elucidated. Results show that the porous mullite ceramics, calcined at 1550 °C for 3 h, possess a porosity of 47%, compressive strength of 31.4 MPa, and thermal conductivity of 0.775 W/(m?K) (at 25 °C), similar to mullite ceramics prepared from pure raw materials. The uniform pore size distribution and sintered neck between the microspheres contribute to the high compressive strength of mullite ceramics, while maintaining high porosity.     

Preparation of calcium hexaluminate porous ceramics by gel-casting method with polymethyl methacrylate as pore-forming agent

Calcium hexaluminate (CA₆) porous ceramics were prepared by gel-casting method, with α-Al₂O₃ and CaCO₃ as raw materials and polymethyl methacrylate (PMMA) microspheres as pore-forming agent. The effects of the amount of pore-forming agent PMMA microspheres on the phase composition, bulk density, apparent porosity, flexural strength, microstructure, thermal shock stability and thermal conductivity of CA₆ porous ceramics were systematically studied. The pores of CA₆ porous ceramics are mainly formed by the burning loss of PMMA microspheres and the decomposition of organic matter. Adding an appropriate amount of PMMA microspheres as pore-forming agent has a positive effect on the thermal shock stability of CA₆ porous ceramics. When the amount of pore-forming agent is 15 wt%, the volume density of CA₆ porous ceramics is 1.33 g/cm³, the porosity is 63%, the flexural strength is 13.9 MPa, the thermal shock times can reach 9 times, and the thermal conductivity is 0.293 W/(m·K), which can meet the application in refractory, ceramics or high temperature cement industries.     

Preparation of Porous Mullite Ceramics Using Fly Ash Cenosphere as a Pore‐Forming Agent by Gelcasting Process

Porous mullite ceramics were fabricated from an industrial grade mullite powder by gelcasting process using fly ash cenospheres (FAC) as a pore‐forming agent. The influence of content of FAC and sintering temperature on the density and strength was evaluated. The microstructure showed that FAC can act as a sintering aid and a pore‐forming agent. When the sintering temperature at 1200°C, porous mullite ceramics with a relatively high porosity (48.1–72.2%), low density (0.84–1.64 g/cm³), low thermal conductivity (0.16–0.22 W/m · K), and high compressive strength (6.21–14.70 MPa) have been obtained.     

Controllable preparation of porous ZrB2–SiC ceramics via using KCl space holders

In this work, a novel and facile technique based on using KCl as space holders, along with partial sintering (at 1900 °C for 30 min), was explored to prepare porous ZrB₂–SiC ceramics with controllable pore structure, tunable compressive strength and thermal conductivity. The as-prepared porous ZrB₂–SiC samples possess high porosity of 45–67%, low average pore size of 3–7 μm, high compressive strength of 32–106 MPa, and low room temperature thermal conductivity of 13–34 W m⁻¹ K⁻¹. The porosity, pore structure, compressive strength and thermal conductivity of porous ZrB₂–SiC ceramics can be tuned simply by changing KCl content and its particle size. The effect of porosity and pore structure on the thermal conductivity of as-prepared porous ZrB₂–SiC ceramics was examined and found to be consistent with the classical model for porous materials. The poring mechanism of porous ZrB₂–SiC samples via adding pore-forming agent combined with partial sintering was also preliminary illustrated.     

Preparation and characterization of porous anorthite ceramics from red mud and fly ash

The porous anorthite ceramics with high porosity, good mechanical strength and low heat conductivity were prepared using red mud and fly ash as raw materials via the pore forming method. The effects of sintering temperature and fly ash on phase evolution, densification, compressive strength, thermal conductivity and microstructure of the ceramic materials were investigated. The results showed that the compressive strength of the porous ceramics had an obvious improvement with the increase in fly ash, and the densification and heat conductivity decreased firstly and then increased. In particular, specimen S2 containing 30 wt% red mud and 40 wt% fly ash sintered at 1150°C had the better performances. It had the water absorption of 18.18%, open porosity of 38.52%, bulk density of 1.29 g/cm³, compressive strength of 42.46 MPa, and heat conductivity of 1.24 W/m·K. X-ray diffraction analysis indicated that mullite, anorthite, α-quartz, and diopside ferrian were the dominant phases in the specimens. Scanning electron microscopy micrographs illustrated that plenty of open pores with strip shape and closed pores with axiolitic shape existed in the specimens. Furthermore, the existence of mullite could prevent crack propagation to enhance the energy of inter-granular fracture. It endowed the porous anorthite ceramics with high porosity, good compressive strength, and low heat conductivity.     

Improved mechanical strength and thermal resistance of porous SiC ceramics with gradient pore sizes

Thermal insulation applications of porous SiC ceramics require low thermal conductivity and high mechanical strength. However, low thermal conductivity and high mechanical strength possess a trade-off relationship, because improving the mechanical strength requires decreasing the porosity, which increases the thermal conductivity. In this study, we established a new strategy for improving both the mechanical strengths and thermal resistances of porous SiC ceramics with micron-sized pores by applying a double-layer coating with successively decreasing pore sizes (submicron- and nano-sized pores). This resulted in a unique gradient pore structure. The double-layer coating increased the flexural strengths and decreased the thermal conductivities of the porous SiC ceramics by 24–70 % and 29–49 % depending on the porosity (48–62 %), improving both their mechanical strengths and thermal resistances. This strategy may be applicable to other porous ceramics for thermal insulation applications.     

Carbothermal reduction synthesis of high porosity and low thermal conductivity ZrC-SiC ceramics via an one-step sintering technique

In this work, porous ZrC-SiC ceramics with high porosity and low thermal conductivity were successfully prepared using zircon (ZrSiO₄) and carbon black as material precursors via a facile one-step sintering approach combining in-situ carbothermal reduction reaction (at 1600 °C for 2 h) and partial hot-pressing sintering technique (at 1900 °C for 1 h). Carbon black not only served as a reducing agent, but also performed as a pore-foaming agent for synthesizing porous ZrC-SiC ceramics. The prepared porous ZrC-SiC ceramics with homogeneous microstructure (with grain size in the 50–1000 nm range and pore size in the 0.2–4 µm range) possessed high porosity of 61.37–70.78%, relatively high compressive strength of 1.31–7.48 MPa, and low room temperature thermal conductivity of 1.48–4.90 W·m^?1K^?1. The fabricated porous ZrC-SiC ceramics with higher strength and lower thermal conductivity can be used as a promising light-weight thermal insulation material.     

Optimal design on the mechanical and thermal properties of porous alumina ceramics based on fractal dimension analysis

In order to investigate the relationship between pore structure and thermal conductivity as well as mechanical strength, porous alumina ceramics (PAC) with various pore structures were fabricated, using starch as the pore‐forming agent. Fractal theory was employed to characterize the pore size distribution more accurately than ever used parameters. The results show that the increase in starch content in PAC leads to an enhanced porosity, a higher mean pore size, and reduced fracture dimension, thermal conductivity and strength. The fractal analysis indicated that the fractal dimension decreases gradually and reaches its minimum value with increasing the starch content up to 25 wt%, but the further incorporation results in an opposite trend. It is suggested from micro‐pore fractographic analysis that the optimization of both thermal insulation performance and mechanical strength are positively correlated with the increase in the mean pore size and proportion of 2‐14 μm pores but negatively corrected with the porosity. These results provide a new perspective and a deeper understanding for fabrication of PAC with both excellent thermal insulation and mechanical performance.     

Microstructure and properties of porous anorthite/mullite whiskers ceramics with high porosity

Porous anorthite/mullite whiskers ceramics with high porosity (>91%) and high strength (>0.45 MPa) have been successfully prepared by foam gel-casting method. Effects of extra mullite whiskers on properties including thermal conductivity and compressive strength at different temperatures were investigated and discussed in terms of microstructure observed through SEM and TEM. The results showed that the addition of extra mullite whiskers in certain content could effectively reduce thermal conductivity, improve the compressive strength both at room and high temperature at same time. When the mullite whiskers content was 20 mol%, the porosity was as high as 91.6 ± 0.19%, the thermal conductivity was low to 0.034 ± 0.003 W/(m·K), and the compressive strength at 1000°C was high to 0.64 ± 0.11 MPa three times to the pure one. Small pores, small grains, and more phase interface or grain boundary caused by the addition of extra mullite whiskers were the main factors for low thermal conductivity. Meanwhile, small pores, closely bonded small grains, and the stable three-dimension network formed by mullite whiskers helped to improve strength.     

Enhanced high‐temperature thermoelectric performance of CdO ceramics with randomly distributed micropores

CdO ceramics with randomly distributed micropores were synthesized by the conventional solid‐state reaction method via adding polymethyl methacrylate (PMMA) as the void forming agent. The introduction of microsized pores can significantly affect both electrical and thermal transport properties of the CdO matrix, and possible underlying mechanisms are discussed. Due to the dramatically reduced thermal conductivity, a highest ZT value of ~0.51 has been achieved in the porous CdO at about 1000 K, increased by about 52% as compared to that of the dense sample without PMMA addition. This work demonstrates that introducing microsized pores is a very simple, low‐cost, and efficient strategy to improve the high‐temperature thermoelectric performance of CdO ceramics.     

Highly porous YSZ ceramic foams using hollow spheres with holes in their shell for high-performance thermal insulation

Yttria-stabilized zirconia (YSZ) porous ceramic foams were fabricated using YSZ microspheres with holes on the surface to determine their properties as insulation materials. Highly porous YSZ ceramics with bimodal pore structures, such as internal pores in single hollow spheres and external pores between the spheres, were successfully prepared using YSZ spheres as raw materials. Additionally, holes were added to the shells to reduce continuous thermal pathways and significantly enhance the insulation properties. Furthermore, by adding holes on the surface of the sphere, the porous foams using a hollow sphere exhibit a maximized porosity of 80.69%, remarkably enhanced their insulation properties with low thermal conductivity (0.10 W/m-K), and have sufficient compressive strength to protect the green body (5.7 MPa). The mechanical strength of the YSZ porous foam was maintained owing to the uniform arrangement of the supports.     

Preparation of porous Y2SiO5 ceramics with relatively high compressive strength and ultra-low thermal conductivity by a TBA-based gel-casting method

Porous Y₂SiO₅ ceramics with relative high compressive strength (as high as 24.45 MPa) and ultra-low thermal conductivity (～0.08 W/m K) were successfully fabricated by a tert-butyl alcohol based gel-casting method. The formation mechanism of the 3D interconnected pores and the properties of the green body are discussed. The porosity, pore size, compressive strength and thermal conductivity could be controlled by varying the initial solid loading and the sintering temperature. When regulating the initial solid loading (from 20 to 50 wt%) and sintering temperature (from 1200 to 1500 °C), the porosity can be controlled between 47.74% and 73.93%, and the compressive strength and the thermal conductivity of porous Y₂SiO₅ ceramics varied from 3.34 to 24.45 MPa and from 0.08 to 0.55 W/m K, respectively. It should be noted that the porous Y₂SiO₅ ceramics with 30 wt% solid loading and sintering at 1400 °C had an open porosity of 61.80%, a pore size of 2.24 μm, a low room-temperature thermal conductivity of 0.17 W/m K and a relatively high compressive strength of 13.91 MPa, which make this porous Y₂SiO₅ ceramics suitable for applications in high-temperature thermal insulators.     

Low cost foam-gelcasting preparation and characterization of porous magnesium aluminate spinel (MgAl2O4) ceramics

Porous MgAl₂O₄ ceramics were prepared via a low cost foam-gelcasting route using MgAl₂O₄ powders as the main raw material, ammonium polyacrylate as a dispersant, a small amount of modified carboxymethyl cellulose as a gelling agent, and TH-IV polymer as a foaming agent. The effects of additive's content, solid loading and gelling temperature on slurry's rheological behavior were investigated, and microstructures and properties of as-prepared porous MgAl₂O₄ ceramics examined. Based on the results, the roles played by the foaming agent in the cases of porosity, pore structure, pore size, mechanical properties and thermal conductivity were clarified. Porosity and pore sizes of as-prepared porous MgAl₂O₄ ceramics increased with increasing the foaming agent from 0.05 to 0.6 vol%. Porous MgAl₂O₄ ceramics with porosity of 75.1% and average pore size of 266 µm exhibited a compressive strength as high as 12.5±0.8 MPa and thermal conductivity as low as 0.24 W/(m K) (at 473 K).     

Effects of pore structure on thermal conductivity and strength of alumina porous ceramics using carbon black as pore-forming agent

In the present work, carbon black (CB) works as a pore-forming agent in the preparation of alumina porous ceramics. The pore structures (i.e. mean pore size, pore size distribution and various pores size proportions) were characterized by means of Micro-image Analysis and Process System (MIAPS) software and mercury intrusion porosimetry. Then their correlation and thermal conductivity as well as strength were determined using grey relation theory. The results showed that the porosity and mean pore size increased against the amount of CB, whereas the thermal conductivity, cold crushing strength and cold modulus of rupture reduced. The <2 μm pores were helpful for enhancing the strength and decreasing the thermal conductivity whereas the >14 μm pores had the opposite effects.     

Preparation of near net size porous alumina-calcium aluminate ceramics by gelcasting-pore-forming agent processs

In the processing of porous ceramics, shrinkage from green body to sintered compact during drying and sintering is one of the key concerns which affect microstructure and properties of porous ceramics. Through releasing gases from the burning of the pore forming agents, and volume expansion from the formation of low density resultants during sintering, the sintering shrinkage can be effectively compensated and near net size preparation can be achieved. Herein, near net size porous alumina-calcium aluminate ceramics with controllable shrinkage have been prepared using a combination of gelcasting and pore-forming agent process by adjusting the amount of CaCO₃ and polymethyl methacrylate (PMMA) microspheres added. Al₂O₃ and CaCO₃ were used as raw materials, PMMA microspheres were used as pore-forming agent, isobutylene/maleic anhydride copolymer (Isobam104) was used as gelling agent and dispersing agent. The effects of the addition amounts of CaCO₃ and PMMA in the slurry on the phase composition, shrinkage, porosity, and strength of porous alumina-calcium aluminate ceramics were investigated. The results show that as the CaCO₃ addition amount increases from 0 to 20 wt%, the shrinkage of the samples gradually decreases from 7.3% to −1.4%, and the consequent porosity increases from 58% to 66%, while the compressive strength increases from 5.9 to 15.5 MPa. When PMMA content increases from 10 to 50 wt%, the shrinkage of the samples decreases first and then increases, the porosity increases from 51% to 74%, and the compressive strength decreases from 12.5 to 5.3 MPa. The mechanisms for controlling shrinkages during preparation of porous alumina-calcium aluminate ceramics can be attributed to the following aspects: on one hand, gas release from burning of PMMA and decomposition of CaCO₃ during sintering; on the other hand, volume expansion due to the formation of lower density calcium aluminates which come from the reactions between CaO and Al₂O₃. The near net size preparation technique is of great significance for the manufacture of porous ceramics since the subsequent machining cost can be effectively reduced.     

Processing and properties of silica-bonded porous nano-SiC ceramics with extremely low thermal conductivity

Silica-bonded porous nano-SiC ceramics with extremely low thermal conductivity were prepared by sintering nano-SiC powder-carbon black template compacts at 600–1200 °C for 2 h in air. The microstructure of the silica-bonded porous nano-SiC ceramics consisted of SiC core/silica shell particles, a silica bonding phase, and hierarchical (meso/macro) pores. The porosity and thermal conductivity of the silica-bonded porous nano-SiC ceramics can be controlled in the ranges of 8.5–70.2 % and 0.057–2.575 Wm⁻¹ K⁻¹, respectively, by adjusting both, the sintering temperature and template content. Silica-bonded porous nano-SiC ceramics with extremely low thermal conductivity (0.057 Wm⁻¹ K⁻¹) were developed at a very low processing temperature (600 °C). The typical porosity, average pore size, compressive strength, and specific compressive strength of the porous nano-SiC ceramics were ∼70 %, 50 nm, 2.5 MPa, and 2.7 MPa·cm³/g, respectively. The silica-bonded porous nano-SiC ceramics were thermally stable up to 1000 °C in both air and argon atmospheres.     

Near‐Net‐Shaped Porous Ceramics for Potential Sound Absorption Applications at High Temperatures

We present an interesting processing route for obtaining alumina/mullite‐based ceramics with controlled porosity and airflow resistance leading to promising microstructures for application as sound absorbers. The use of ceramic materials aims for potential applications where high temperatures or corrosive atmospheres are predominant, e.g., in combustion chambers of gas turbines. For the production of the porous ceramics we combined freeze gelation and sacrificial templating processes to produce near‐net‐shaped parts with low shrinkage (<3%) based on environmental‐friendly and low cost conditions. The obtained microstructure presents a bimodal pore size distribution, with small pores derived from the freeze gelation process (~30 μm) connecting large pores (2–5 mm diameter) originated from the expanded polystyrene template particles. These connections, called “windows” in this study, show a significant impact on the sound absorption properties, allowing the pressure diffusion effect to take place, resulting in a significant improvement of the sound absorption coefficient. By varying the template particle content and the slurry solid content, it is possible to control the sound absorption behavior at different frequencies of the open‐celled ceramics. These ceramics feature a high open porosity, from 77% to 82%, combined with sufficient compressive strength ranging from 0.27 to 0.68 MPa and sound absorption coefficients of 0.30–0.99, representing a highly promising combination of properties for noise control and reduction at corrosive environments and high temperatures.     

Effect of starch addition on microstructure and properties of highly porous alumina ceramics

Porous alumina ceramics with ultra-high porosity were prepared through combining the gel-casting process with the pore-forming agent technique. Porosity and pore size distribution of the sintered bulks were evaluated with and without adding starch, respectively. In particular, the influences of starch addition on the properties, including thermal conductivity and compressive strength were studied. It was found that the incorporation of starch increased the nominal solid loading in the suspension and subsequently promoted the particle packing efficiency. The porosity is raised with increasing starch content from 0 to 30 vol%, which brings the decrease in thermal conductivity, whereas the compressive strength isn't seriously degraded. The further higher starch addition (40 vol%), however, would deteriorate the performance of the alumina porous ceramics. It is believed that the appropriate starch amount (lower than 30 vol%), working as a pore-forming agent, suppresses the driving force of densification without affecting the connections of neighboring grains while excessive starch amount would lead to the collapse of the porous structure.     

Preparation and properties of porous ceramics from nickel slag by aerogel gelcasting

To further resource industrial solid waste, porous ceramics with high porosity were prepared by a gelcasting method using nickel slag and kaolin as raw materials and hydrophilic nontoxic SiO₂ aerogel as a gelling agent. The effects of nickel slag content, dispersant and solid content on the properties and microstructure of porous ceramics were investigated in detail in terms of density, compressive strength, porosity, phase composition and micromorphology. The results confirmed that a certain amount of nickel slag can effectively improve the porosity of porous ceramics, while the addition of dispersant can promote the flow of the slurry, enhanced the denseness of the raw billet and significantly improved the compressive strength. However, its excessive use had a negative effect on the ceramic density and porosity. At the same time, the solid content played a key role in the performance of porous ceramics prepared by gelcasting, and too much solid content was also not conducive to the generation of pores. When the nickel slag content was 55%, the amount of dispersant was 2%, and the solid content was 60 vol%, the porous ceramic had a better overall performance, the density of the porous ceramic was 510 kg/m³, the compressive strength was 1.3 MPa, and the porosity reached 80.1%. The major crystalline phases of porous ceramics prepared by nickel slag were cordierite and anorthite.     

On the role of the pore morphology on the electrical conductivity of porous yttria-stabilized zirconia

Yttria Stabilized Zirconia ceramics with well-controlled porosity, pore size and shape were prepared using well-calibrated poly-methyl-methacrylate (PMMA) micro-beads (MB) as a pore-forming agent. The microstructure was observed by Scanning Electron Microscopy. Impedance spectroscopy was used to evaluate the effect of pore morphology (pore size, pore size distribution, pore shape and interconnectivity) on the electrical properties of YSZ ceramics. Archie's law based analyzes to express the dependence of conductivity on porosity have shown that Archie's law is independent of pore size for a pore diameter of between 1 and 7 μm. The Bruggeman model could be used to predict the bulk conductivity if the porosity was less than 25%, thus showing that the impedance response included the effect of sinuousness and constriction induced by pores. Therefore, the tortuosity factor calculated from the bulk conductivity was higher than that predicted by the Bruggeman model for porosities greater than 25% and spherical pores wide (>20 μm). Another point relates to the comparison between tortuosity factors obtained for pore samples fabricated with pore-forming PMMA or by sub-sintering.