Ink‐jet printing of cotton with natural dyes

Four natural dyes, annatto, cutch, pomegranate fruit rind, and golden dock, were used as colorants for the preparation of water‐based ink‐jet inks for digital textile printing. The physical and rheological properties (pH, conductivity, surface tension, and viscosity) of the inks were measured over a period of 90 days for the evaluation of ink stability and suitability for ink‐jet printing. The inks were found to be suitable and were used for the digital printing of cotton fabrics. The prints were subjected to wash, light, and rub fastness tests and colour measurements. Colour consistency and fastness results, especially after fixation, are comparable with those of synthetic dyes, which paves the way for the production of environmentally friendly ink‐jet inks using natural dyes for the digital printing of cotton through the formulation of suitable printing techniques.     

Disperse ink‐jet inks: properties and application to polyester fibre

Water‐based ink‐jet inks were prepared using press cake samples of two commercially available azo disperse dyes. The suitability of the inks for printing polyester fabric was evaluated via measurement of surface tension, conductivity, viscosity, pH and particle size distribution. Inks prepared by the proposed method fulfill most requirements for an ink‐jet ink depending on the colorant structure, the dispersing agent and the alcohol used. The inks were applied to polyester fabric by both printing and dyeing and the fastness of the ensuing coloured samples was assessed. The fastness properties of the dyed and printed polyester samples were found to be very good to excellent and generally meet accepted customer requirements. Oil‐in‐water microemulsions containing the same colorants were also prepared. Their properties, which are crucial to the suitability for ink‐jet ink, were compared with those of the conventionally prepared inks and were found to be improved, with the exception of conductivity, while surface tension remained within acceptable values.     

An experimental analysis of the influence of the ink properties on the drop formation for direct thermal inkjet printing of high solid content aqueous 3Y-TZP suspensions

Direct inkjet printing (DIP) of ceramics as a novel solid freeform fabrication (SFF) method has been subjected to extensive research in the recent years. The studies have focused either on the simulation of the drop ejection or the production of demonstration objects. The aim of this study was to close the gap between the simulation results and product oriented studies. 3Y-TZP inks of 24 vol.% solid content were prepared and characterized in terms of physical properties as well as dimensionless quantities (Re, We, Ca, and Oh). The drop volume and velocity were estimated by considering a constant ejection pressure but varying physical properties of the ejected inks. A thermal inkjet printer was used to eject arrays of single drops as well as three-dimensional 3Y-TZP demonstration objects. The drop arrays were analyzed to determine the relation between the ink properties and the drop formation. The demonstration object was sintered close to the full density.     

Single‐phase ink‐jet printing onto cotton fabric

The current commercial application of ink‐jet reactive inks to cotton fabrics requires pretreating with pad liquor containing a thickener, urea and alkali prior to printing. In this study, attempts have been made to develop a reactive ink‐jet print in a single‐phase process by adding an organic salt to the ink formulation and hence removing the need to pretreat fabrics. This approach utilises inks containing both a reactive dye, in this case Procion Red H‐E3B, and an organic salt such as sodium formate, sodium acetate, sodium propionate or tri‐sodium citrate. The behaviour of a novel reactive ink formulation for ink‐jet printing on to cotton fabric was evaluated at different pH vlaues. The results at optimum pH indicated that printed non‐pretreated fabrics with ink containing organic salts exhibited a higher level of reactive dye fixation than printed pretreated fabric containing no organic salt ink. The yielded prints demonstrate excellent colour fastness to washing and dry/wet crocking properties. The light fastness of the printed fabrics was improved by adding an organic salt to the ink formulation.     

Colour management of a low‐cost four‐colour ink‐jet printing system on textiles

A low‐cost four‐colour (RBYK) dye‐based ink‐jet printing system for textiles was introduced in this study, in which red and blue inks were employed instead of the magenta and cyan inks used in half‐tone printing. The basis of a colour‐management system for this device was developed by determining the mapping between XYZ tristimulus values of output colours and the digital RBYK values using polynomial transforms. A second‐order equation was found to give the best performance with an average characterisation error of under 7 CIELAB units.     

Ionic liquids as performance additives for water‐based printing inks

For the first time, the use of ionic liquids as additives for printing inks in order to improve the wettability of the printing base by the ink is presented. The aim of this work was to study the influence of ionic liquids on the selected properties of water‐based printing ink and the prints. The contact angles of the printing inks on the printing base were measured. Modified flexographic inks were laboratory printed on polypropylene plastic film. The impact of small amounts of various ionic liquids on printing ink colour was examined in terms of the optical density of the full‐tone area, the colour parameters (L*, a*, b*, CIE), the total colour difference, and the gloss of the dried ink film. The influence of ionic liquids on the ink contact angle, the optical density, and the L*a*b* coordinates is discussed. In general, the investigated ionic liquids improve the wettability of water‐based flexographic printing ink, with an acceptable total colour difference. The optical density is increased for printing inks containing ionic liquids in comparison with the original flexographic printing ink, Process.     

陶瓷喷墨打印成型技术进展

陶瓷喷墨打印成型技术是一种把计算机辅助制造(CAM)应用于陶瓷成型中的新技术.它是在计算机控制下多层打印逐层叠加制出三维陶瓷坯体.它在复杂单体陶瓷制造、有序成分复合材料制造,固体氧化物燃料电池制造等方面有很好的应用前景.本文概述了陶瓷喷墨打印技术的进展状况.着重介绍了该技术的历史原理设备和陶瓷墨水性能要求,以及现存的问题.     

Properties of ink‐jet printed,ultraviolet‐cured pigment prints in comparison with screen‐printed,thermo‐cured pigment prints

A collection of printed fabrics for men’s shirts was designed and prepared using computer‐aided design/computer‐aided manufacturing technology. The colours for designs were ink‐jet printed on cotton fabrics with pigments and ultraviolet‐cured. These prints represented the target colours for subsequent flat‐screen printing, which was performed using pigment printing pastes and thermal curing. For an exact transfer of colours of the ink‐jet‐printed standard into the screen‐printing process, a computer recipe prediction method was used. A comparison of colorimetric parameters of fabrics printed with both printing techniques shows minimal and acceptable differences in the CIELab colour values. A comparison of colour fastness properties proves that very good colour fastness is achieved on the pigment‐printed fabrics produced with both printing techniques. The flat‐screen‐printed fabrics show better colour fastness to washing, perspiration and rubbing, while ink‐jet‐printed fabrics show better colour fastness to dry‐cleaning and light. The fabrics printed with both printing techniques have high rigidity and non‐elastic properties. The mechanical and physical parameters are strongly dependent upon the amount of the dry substance of the printing media applied on the cotton fabric surface, which is higher on screen‐printed fabrics. The ink‐jet‐printed fabrics show better air permeability than flat‐screen‐printed fabrics.     

Preparation of pigmented ink‐jet ink by a combination of surface treatments and synthetic dispersant

Drop‐on‐demand ink‐jet inks prepared from dyes usually show inadequate light and water fastness. Thus, in our previous paper, we studied black pigmented ink‐jet inks with the aim of overcoming the drawbacks of dye‐based ink by employing a variety of synthetic dispersants with gas black. In this study, pigmented ink‐jet inks were prepared by a combination of the synthetic dispersant and the surface treatments of a furnace black that is more common than gas blacks. The results of this study show that the surface treatment of the furnace black and the use of the synthetic dispersant are useful in the preparation of ink‐jet inks and endow them with properties that are comparable with those of commercial ink‐jet inks.     

Ink‐jet Printing of Hollow SnO2 Nanospheres for Gas Sensing Applications

Hollow tin‐oxide (SnO₂) nanospheres were synthesized by coating, carbon nanospheres (CNs) as hard templates, with a tin(IV) sol obtained by partial hydrolysis of [Sn(OBu^t)₄] under ambient conditions. Formation of crystalline SnO₂ spheres upon calcination was confirmed by powder X‐ray diffraction data, whereas the hollow interiors of SnO₂ particles were verified by scanning and transmission electron microscopy of both intact and broken spheres. The shell of SnO₂ nanospheres sintered at 700°C consisted of a single layer of nanocrystallites (~6 nm) self‐assembled in a ball‐like superlattice. Tin‐oxide hollow spheres showed an average diameter of 150 nm and could be homogeneously dispersed in water/ethylene glycol (50:50 vol%) mixture to form stable inorganic inks viable for their use in commercial ink‐jet printers demonstrated by printing porous ceramic structures on an interdigitated sensor chip. The integration of large surface and nanoscopic voids in the final structures imparted higher sensitivity to the as‐printed sensors toward both oxidizing (nitrogen dioxide) and reducing gases (methane and ethanol), which validates the enormous potential of printable inorganics in functional applications.     

Colloidal properties of copolymer‐encapsulated and surface‐modified pigment dispersion and its application in inkjet printing inks

A styrene–maleic acid copolymer (PSMA)‐encapsulated 2‐[(2‐methoxy‐4‐nitrophenyl) azo]‐N‐(2‐methoxyphenyl)‐3‐oxobutyramide (PY74) dispersion was prepared by the phase‐separation technique. A surface‐modified PY74 dispersion was prepared with PSMA sodium as a dispersant by the milling method. Furthermore, the two dispersions were applied to formulate pigment inks. The colloidal properties of these two dispersions were compared. The printing and color performance of the prepared inks were also investigated. The results show that the PSMA‐encapsulated PY74 dispersion with a small particle size had higher stabilities of NaCl concentration, pH value, and temperature than the surface‐modified PY74 dispersion. The apparent viscosity of the PSMA‐encapsulated PY74 dispersion changed little, while it changed greatly in the surface‐modified PY74 dispersion with an increase of the shear rate from 10 to 100 s⁻¹. The ink printing and color performance of printed Fabrics indicated that the PSMA‐encapsulated PY74 dispersion was more suitable for the preparation of inkjet printing ink than the surface‐modified PY74 dispersion. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Syntheses of polymeric dispersants for pigmented ink‐jet inks

Drop‐on‐demand ink‐jet inks made from dyes usually show poor light fastness and poor water fastness. Therefore, many researchers have introduced pigments into ink‐jet inks to overcome the defects of dye‐based ink. Pigmented ink needs sophisticated technology which disperses the pigments stably in low viscosity. Thus, adequate dispersants are essential to achieve stable dispersions of pigments for ink‐jet inks. This study describes syntheses of dispersants, properties of formulations and comparisons of performance with an existing ink to assess their suitability for commercial application.     

Piezoelectric Properties of Ink‐Jet–Printed Lead Zirconate Titanate Thick Films Confirmed by Piezoresponse Force Microscopy

An ink consisting of Pb(Zr_0.53Ti_0.47)O₃ (PZT) particles with a median size of 170 nm and a narrow size distribution, in a dispersion of water and glycerol, and with a low viscosity and surface tension, was used for the fabrication of thick films by piezoelectric ink‐jet printing. This study reports the printing conditions, the subsequent thermal treatment of the as‐deposited layers, and the properties of the sintered PZT thick film. The film, sintered at 1100°C, had a locally dense microstructure and consisted of grains that are a few 100 nm across, as revealed by scanning electron microscopy. A local piezoelectric response of 15 pm/V was measured in the ink‐jet–printed PZT thick film by piezoresponse force microscopy.     

喷墨打印机颜料型油墨的最新进展

喷墨打印技术是一种非接触式的数字印刷技术,它将数码技术与传统的印刷技术合二为一。用于喷墨印刷的染料型墨水通常表现出差的耐光性和耐水性,因此将颜料引进到喷墨油墨中以克服染料型墨水的缺点是必然趋势。为了在低粘度下保持颜料稳定的分散,性能优异的合成分散剂对于获得稳定的颜料分散体是必不可少的。本文介绍了水性喷墨油墨的组分及各组分作用,对喷墨油墨的生产技术、发展前景进行了展望。     

Synthesis,stability and printing properties of a novel 2‐sulphophenoxy‐4‐chloro‐s‐triazine reactive dye for ink‐jet printing of wool

We report here the synthesis and characterisation of a new medium‐reactivity reactive dye containing 2‐sulphophenoxy‐4‐chloro‐s‐triazine, having enhanced the activity of the chlorine atom for further substitution by the functional groups carried by wool fibre. In addition, a dichloro‐s‐triazine dye was also synthesised for the purpose of comparison. The progress of synthesis reactions and purity of the dyes were determined using capillary electrophoresis and thin layer chromatography. The molecular structure and the chemical compositions of the synthesised dyes were confirmed using Fourier Transform–infrared spectral data and elemental analyses. The inks containing the synthesised dyes were formulated and ink‐jet‐printed onto wool fabrics and then the printed fabrics were steamed at 102°C. Compared with the dichloro‐s‐triazine dye, superior performance in terms of ink stability, K/S and dye fixation was observed for the new 2‐sulphophenoxy‐4‐chloro‐s‐triazine dye. In addition, the light fastness of the fabric printed with the inks containing the new dye was 0.5‐grade greater than that of the fabric printed with the inks containing the dichloro‐s‐triazine dye, and no changes in shade and staining were observed following wash fastness tests of the fabrics printed with the inks containing the new dye.     

Visualization and simulation of the transfer process of index‐matched silica microparticle inks for gravure printing

A combined experimental and computational study of the transfer of transparent index‐matched silica‐particle inks between two flat plates is presented for gravure printing applications. The influence of printing speed and initial ink droplet size on the ability to accurately transfer ink during the printing process is explored systematically. Smooth interface volume of fluid simulations show the same trends as the ink transfer observed in experiments over a wide range of printing speeds and for inks having different silica particle loadings. Our calculations indicate that for ink droplets with characteristic dimensions in the vicinity of 10 μm, which are of particular interest for gravure printing applications, ink transfer improves significantly due to the diminishing effect of gravity, and the increased importance of capillary forces at small length scales. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1419–1429, 2017     

Synthesis of a di‐(p‐sulphophenoxy)‐s‐triazine reactive dye and its application in wool fabric ink‐jet printing

Reactive dyes based on p‐sulphophenoxy‐s‐triazines were synthesised, characterised and applied to wool fabric by ink‐jet printing. The extent of dye‐fibre covalent bonding (% fixation) was measured on prints produced using different development methods. The most promising method to obtain high dye‐fibre fixation values was to interleave the printed wool with a pre‐wetted cotton fabric and store for 3 h. Steam fixation was also investigated but gave lower fixation values. The degree of dye hydrolysis vs time in the ink formulation was evaluated because ink stability is critical in commercial operation; a reformulated ink based on a phosphate buffer was found to improve ink stability.     

Synthesising polymeric dispersants to apply to carbon black pigmented mill bases for use in ink‐jet inks

Dyes are an important component of drop‐on‐demand ink‐jet inks and are commonly used in desktop printers. While they offer bright, vivid colour, these dyes exhibit poor light and water fastness. To combat this, researchers have started using pigmented ink‐jet inks instead of dye‐based inks to improve light and water fastness, but the pigments are insoluble in ink vehicles. To use pigments, dispersants must be applied; however, this is a delicate process because the properties of the dispersant substantially affect how the pigmented mill base must be prepared. In this study, polymeric dispersants are synthesised based on the properties and ratios of monomers and the molecular weights of polymers. In total, 14 types of polymeric dispersants are synthesised and examined, with special attention paid to the dispersing properties of particle size reduction and the stability of the pigmented mill base used to prepare drop‐on‐demand ink‐jet inks. This study describes the synthesis of the dispersants in terms of their suitability for commercial application.     

喷墨打印技术的发展现状

简要介绍了喷墨打印技术的发展现状。目前主要有两类喷墨打印技术:连续喷墨打印和脉冲喷墨打印技术。前者可设计成双重或多重弯曲系统;后者可分为热喷墨、压电喷墨、阀门喷墨、静电喷墨过程,描述了喷墨打印用墨的最新发展。水性、溶剂性、热熔性、紫外固化和反应性墨是目前主要的喷墨打印用墨。     

Integration of ink jet and transfer printing for device fabrication using nanostructured materials

Low viscosity, dilute inks of carbonaceous materials that tend to run, spread, and dry unevenly pose a major challenge towards ink jet printing approaches. A porous, planar stamp based methodology outlined here combines the advantages of ink jet and transfer printing while enabling printing of dilute inks comprising nanowires, nanotubes, nanoparticles, and biological molecules. Integration of ink jet and transfer printing is reported with agarose gel planar stamp, for carbon nanotube inks, enabling the formation of gate modulated channels between source and drain electrodes without necessitating any lithography steps.