Line-scanning Raman imaging spectroscopy for detection of fingerprints

Fingerprints are the best form of personal identification for criminal investigation purposes. We present a line-scanning Raman imaging system and use it to detect fingerprints composed of β-carotene and fish oil on different substrates. Although the line-scanning Raman system has been used to map the distribution of materials such as polystyrene spheres and minerals within geological samples, this is the first time to our knowledge that the method is used in imaging fingerprints. Two Raman peaks of β-carotene (501.2, 510.3 nm) are detected and the results demonstrate that both peaks can generate excellent images with little difference between them. The system operates at a spectra resolution of about 0.4 nm and can detect β-carotene signals in petroleum ether solution with the limit of detection of 3.4×10(-9) mol/L. The results show that the line-scanning Raman imaging spectroscopy we have built has a high accuracy and can be used in the detection of latent fingerprints in the future.     

Stand-off detection of explosives particles by multispectral imaging Raman spectroscopy

A Raman multispectral imaging technique is presented, which can be used for stand-off detection of single explosives particles. A frequency-doubled Nd:YAG laser operating at 10 Hz illuminates the surface under investigation. The backscattered Raman signal is collected by a receiver subsystem consisting of a 150 mm Schmidt-Cassegrain telescope, a laser line edge filter, a liquid-crystal tunable filter, and a gated intensified charge-coupled device (ICCD) detector. A sequence of images is recorded by the ICCD, where, for each recording, a different wavelength is selected by the tunable filter. By this, a Raman spectrum is recorded for each pixel, which makes it possible to detect even single particles when compared to known spectra for possible explosives. The comparison is made using correlation and least-square fitting. The system is relatively insensitive to environment and light variations. Multispectral Raman images of sulfur, ammonium nitrate, 2,4-dinitrotoluene, and 2,4,6-trinitrotoluene were acquired at a stand-off distance of 10 m. Detection of sulfur particles was done at a distance of 10 m.     

Noninvasive detection of concealed liquid explosives using Raman spectroscopy

We present a Raman spectroscopic method for the noninvasive detection of liquid explosives within bottles, and other packaging, of substantially higher sensitivity and wider applicability than that currently available via conventional Raman spectroscopy. The approach uses a modification of the spatially offset Raman spectroscopy (SORS) concept, which permits the interrogation of a wide range of containers, including transparent, colored, and diffusely scattering plastic and glass beverage, medicine, and cosmetic bottles, with no change in experimental geometry. The enhanced sensitivity is achieved by the technique's inherent ability to effectively suppress fluorescence and Raman contributions originating from the wall of the container. The application is demonstrated on the noninvasive detection of hydrogen peroxide solution, a critical component of a number of liquid explosives. In contrast to conventional Raman spectroscopy, the modified SORS concept enables the detection of concealed hydrogen peroxide solution in all the studied cases.     

In situ trace detection of peroxide explosives by desorption electrospray ionization and desorption atmospheric pressure chemical ionization

Desorption electrospray ionization (DESI) mass spectrometry is used for the rapid (<5 s), selective, and sensitive detection of trace amounts of the peroxide-based explosives, hexamethylene triperoxide diamine (HMTD), tetracetone tetraperoxide (TrATrP), and triacetone triperoxide (TATP), directly from ambient surfaces without any sample preparation. The analytes are observed as the alkali metal ion complexes. Remarkably, collision-induced dissociation (CID) of the HMTD, TATP, and TrATrP complexes with Na(+), K(+), and Li(+) occurs with retention of the metal, a process triggered by an unusual homolytic cleavage of the peroxide bond, forming a distonic ion. This is followed by elimination of a fragment of 30 mass units, shown to be the expected neutral molecule, formaldehyde, in the case of HMTD, but shown by isotopic labeling experiments to be ethane in the cases of TATP and TrATrP. Density functional theory (DFT) calculations support the suggested fragmentation mechanisms for the complexes. Binding energies of Na+ of 40.2 and 33.1 kcal/mol were calculated for TATP-Na(+) and HMTD-Na(+) complexes, suggesting a strong interaction between the peroxide groups and the sodium ion. Increased selectivity is obtained either by MS/MS or by doping the spray solvent with additives that produce the lithium and potassium complexes of TATP, HMTD, and TrATrP. Addition of dopants into the solvent spray increased the signal intensity by an order of magnitude. When pure alcohol or aqueous hydrogen peroxide was used as the spray solvent, the (HMTD + Na)+ complex was able to bind a molecule of alcohol (methanol or ethanol) or hydrogen peroxide, providing additional characteristic ions to increase the selectivity of analysis. DESI also allowed the rapid detection of peroxide explosives in complex matrixes such as diesel fuel and lubricants using single or multiple cation additives (Na(+), K(+), and Li(+), and NH4(+)) in the spray solvent. Low-nanogram detection limits were achieved for HMTD, TrATrP, and TATP in these complex matrixes. The DESI response was linear over 3 orders of magnitude for HMTD and TATP on paper surfaces (1-5000 ng), and quantification of both peroxide explosives from paper gave precisions (RSD) of less than 3%. The use of pure water and compressed air as the DESI spray solution and nebulizing gas, respectively, showed similar ionization efficiencies to those obtained using methanol/water mixtures and nitrogen gas (the typical choices). An alternative ambient method, desorption atmospheric pressure chemical ionization (DAPCI), was also used to detect trace amounts of HMTD and TATP in air by complexation with gas-phase ammonium ions (NH4(+)) generated by atmospheric pressure ammonia ionization.     

A positively charged silver nanowire membrane for rapid on-site swabbing extraction and detection of trace inorganic explosives using a portable Raman spectrometer

The sensitive and on-site detection of inorganic explosives has raised serious concerns regarding public safety.However,high stability and non-volatility features currently limit their rapid on-site detection.Surface-enhanced Raman spectroscopy (SERS) is emerging as a powerful technique for the trace-level detection of different molecules.Plasmonic Ag nanowires were produced by a hydrothermal synthesis method using polyvinylpyrrolidone (PVP) as a negatively charged stabilizer.Here,we report a rapid detection method for inorganic explosives based on a simple surface swab with a positively charged diethyldithiocarbamate-modified Ag nanowire membrane coupled with SERS.This membrane,serving as an excellent SERS substrate with high uniformity,stability,and reusability,can capture both typical oxidizers in inorganic explosives and organic nitro-explosives,via electrostatic interaction.The detection level of perchlorates (ClO4-),chlorates (ClO3-),nitrates (NO3-),picric acid,and 2,4-dinitrophenol is as high as 2.0,1.7,0.1,45.8,and 36.6 ng,respectively.In addition,simulated typical inorganic explosives such as black powders,firecrackers,and match heads could also be detected.We believe that this membrane represents an attractive alternative for rapid on-site detection of inorganic explosives with high efficiency.     

Paper-based SERS swab for rapid trace detection on real-world surfaces

One of the important but often overlooked considerations in the design of surface-enhanced Raman scattering (SERS) substrates for trace detection is the efficiency of sample collection. Conventional designs based on rigid substrates such as silicon, alumina, and glass resist conformal contact with the surface under investigation, making the sample collection inefficient. We demonstrate a novel SERS substrate based on common filter paper adsorbed with gold nanorods, which allows conformal contact with real-world surfaces, thus dramatically enhancing the sample collection efficiency compared to conventional rigid substrates. We demonstrate the detection of trace amounts of analyte (140 pg spread over 4 cm2) by simply swabbing the surface under investigation with the novel SERS substrate. The hierarchical fibrous structure of paper serves as a 3D vasculature for easy uptake and transport of the analytes to the electromagnetic hot spots in the paper. Simple yet highly efficient and cost-effective SERS substrate demonstrated here brings SERS-based trace detection closer to real-world applications.     

Passive standoff detection of chemical warfare agents on surfaces

Results are presented on the passive standoff detection and identification of chemical warfare (CW) liquid agents on surfaces by the Fourier-transform IR radiometry. This study was performed during surface contamination trials at Defence Research and Development Canada-Suffield in September 2002. The goal was to verify that passive long-wave IR spectrometric sensors can potentially remotely detect surfaces contaminated with CW agents. The passive sensor, the Compact Atmospheric Sounding Interferometer, was used in the trial to obtain laboratory and field measurements of CW liquid agents, HD and VX. The agents were applied to high-reflectivity surfaces of aluminum, low-reflectivity surfaces of Mylar, and several other materials including an armored personnel carrier. The field measurements were obtained at a standoff distance of 60 m from the target surfaces. Results indicate that liquid contaminant agents deposited on high-reflectivity surfaces can be detected, identified, and possibly quantified with passive sensors. For low-reflectivity surfaces the presence of the contaminants can usually be detected; however, their identification based on simple correlations with the absorption spectrum of the pure contaminant is not possible.     

Identification of thaumasite in concrete by Raman chemical imaging

Identification of thaumasite (CaSiO₃·CaO₃·CaSO₄·15H₂O) in concrete undergoing external sulfate attack by X-ray powder diffraction or by microscopic techniques is difficult due to its crystallographic and morphological similarity with ettringite. Widefield Raman chemical imaging via liquid crystal tunable filter (LCTF) technology has been used in a preliminary study to determine the presence of thaumasite in association with ettringite (3CaO·Al₂O₃·3CaSO₄·32H₂O) and gypsum (CaSO₄·2H₂O). Raman chemical imaging combines Raman spectroscopy with optical microscopy and digital imaging to provide images with molecular-based contrast. Thaumasite has three major peaks at 658, 990, 1076 cm⁻¹ and three minor peaks at 417, 453, 479 cm⁻¹. Ettringite has major peaks at 990, 1088 cm⁻¹. Gypsum has a major peak at 1009 cm⁻¹ and minor peaks at 417, 496, 621, 673, 1137 cm⁻¹. When these minerals are presented together, Raman chemical imaging provides an excellent way to determine their molecular composition and spatial distribution within the sample.     

Raman chemical imaging spectroscopy reagentless detection and identification of pathogens: signature development and evaluation

An optical detection method, Raman chemical imaging spectroscopy (RCIS), is reported, which combines Raman spectroscopy, fluorescence spectroscopy, and digital imaging. Using this method, trace levels of biothreat organisms are detected in the presence of complex environmental backgrounds without the use of amplification or enhancement techniques. RCIS is reliant upon the use of Raman signatures and automated recognition algorithms to perform species-level identification. The rationale and steps for constructing a pathogen Raman signature library are described, as well as the first reported Raman spectra from live, priority pathogens, including Bacillus anthracis, Yersinia pestis, Burkholderia mallei, Francisella tularensis, Brucella abortus, and ricin. Results from a government-managed blind trial evaluation of the signature library demonstrated excellent specificity under controlled laboratory conditions.     

Identification of explosives with two-dimensional ultraviolet resonance Raman spectroscopy

The first two-dimensional (2D) resonance Raman spectra of TNT, RDX, HMX, and PETN are measured with an instrument that sequentially and rapidly switches between laser wavelengths, illuminating these explosives with forty wavelengths between 210 nm and 280 nm. Two-dimensional spectra reflect variations in resonance Raman scatter with illumination wavelength, adding information not available from single or few one-dimensional spectra, thereby increasing the number of variables available for use in identification, which is especially useful in environments with contaminants and interferents. We have recently shown that 2D resonance Raman spectra can identify bacteria. Thus, a single device that identifies the presence of explosives, bacteria, and other chemicals in complex backgrounds may be feasible.     

Anti-Stokes Raman spectrometry with 1064-nm excitation: an effective instrumental approach for field detection of explosives

Anti-Stokes Raman spectra of 28 explosive materials were obtained with 1064-nm excitation using fiber-optic sampling and a dispersive spectrograph equipped with a charge-coupled device (CCD) array detector. By using a silicon CCD detector, anti-Stokes features could clearly be observed for the majority of samples from -250 to -1650 cm(-1). Using the fiber-optic probe, spectra were routinely obtained from samples positioned up to twelve meters from the spectrograph within 240 s. The utility of an anti-Stokes correction routine is demonstrated, which routine allowed anti-Stokes spectra measured with 1064-nm excitation to be successfully searched and identified against libraries of Stokes spectra obtained using a Fourier transform (FT) Raman system equipped with a 1064-nm Nd:YAG laser.     

Noninvasive detection of concealed explosives: depth profiling through opaque plastics by time-resolved Raman spectroscopy

The detection of explosives concealed behind opaque, diffusely scattering materials is a challenge that requires noninvasive analytical techniques for identification without having to manipulate the package. In this context, this study focuses on the application of time-resolved Raman spectroscopy (TRRS) with a picosecond pulsed laser and an intensified charge-coupled device (ICCD) detector for the noninvasive identification of explosive materials through several millimeters of opaque polymers or plastic packaging materials. By means of a short (250 ps) gate which can be delayed several hundred picoseconds after the laser pulse, the ICCD detector allows for the temporal discrimination between photons from the surface of a sample and those from deeper layers. TRRS was applied for the detection of the two main isomers of dinitrotoluene, 2,4-dinitrotoluene, and 2,6-dinitrotoluene as well as for various other components of explosive mixtures, including akardite II, diphenylamine, and ethyl centralite. Spectra were obtained through different diffuse scattering white polymer materials: polytetrafluoroethylene (PTFE), polyoxymethylene (POM), and polyethylene (PE). Common packaging materials of various thicknesses were also selected, including polystyrene (PS) and polyvinyl chloride (PVC). With the demonstration of the ability to detect concealed, explosives-related compounds through an opaque first layer, this study may have important applications in the security and forensic fields.     

Use of a geometry optimized fiber-optic surface-enhanced Raman scattering sensor in trace detection

A novel SERS (surface-enhanced Raman scattering) sensor has been recently developed; its peculiar geometry is able to increase considerably both the SERS active surface and the number of internal reflections at the interface between silica and silver, thus allowing an increase of the signal intensity. The aim of this work is to demonstrate that this sensor could be efficiently used to detect some molecules such as illegally used veterinary medicine (crystal violet and malachite green) below the ppb detection limit. The advantages of this sensor with respect to other detection techniques are not only the higher sensitivity, but also the fast response and the possibility of coupling with a portable Raman spectrometer for "on-field" measurements. The ability of the sensor to work under real environmental conditions in the presence of many cationic and anionic species has been tested both in solutions containing sodium and chlorine ions and in water coming from the aqueduct of Milan and from the (normally polluted) river Serio.     

Development of SRM 2907 trace terrorist explosives simulants for the detection of Semtex and triacetone triperoxide

Effective and accurate detection of trace explosives is crucial in the effort to thwart terrorist explosives attacks. A National Institute of Standards and Technology (NIST) standard reference material (SRM) has been developed for the evaluation of trace explosives detectors that sample by collection of residue particles using swiping or air filtration. SRM 2907 Trace Terrorist Explosives Simulants consists of two materials individually simulating the residues of the plastic explosive Semtex [for pentaerytritol tetranitrate (PETN)] and the improvised explosive triacetone triperoxide (TATP). Unique challenges were encountered in the development of these materials, including the selection of suitable inert substrates, material preparation, thermal stability testing, and analytical method development. Two independent analytical methods based on liquid chromatography with ultraviolet absorbance and mass spectrometric detection, LC-UV and LC/MS, respectively, were developed and used to certify the mass fractions of PETN and TATP. These materials were further evaluated for their suitability on a field swipe-sampled trace explosives detectors based on ion mobility spectrometry (IMS).     

Surface-enhanced Raman scattering detection of chemical and biological agent simulants

Surface-enhanced Raman scattering spectra of chemical and biological agent simulants, such as dimethyl methylphonate, pinacolyl methylphosphonate, diethyl phosphoramidate, 2-chloroethyl ethylsulfide, bacillus globigii, erwinia herbicola, and bacillus thuringiensis were obtained from silver-oxide film-deposited substrates. Thin AgO films ranging in thickness from 50 to 250 nm were produced by chemical bath deposition onto glass slides. Further Raman intensity enhancements were noticed in UV irradiated surfaces due to photo-induced Ag nanocluster formation, which may provide a possible route to producing highly useful plasmonic sensors for the detection of chemical and biological agents upon visible-light illumination.     

High-throughput trace analysis of explosives in water by laser diode thermal desorption/atmospheric pressure chemical ionization-tandem mass spectrometry

Harmful explosives can accumulate in natural waters in the long term during their testing, usage, storage, and dumping and can pose a health risk to humans and the environment. For the first time, attachment of small anions to neutral molecules in laser diode thermal desorption/atmospheric pressure chemical ionization was systematically investigated for the direct determination of trace nitroaromatics, nitrate esters, and nitramine explosives in water. Using ammonium chloride as an additive improved the instrument response for all the explosives tested and promoted the formation of several characteristic adduct ions. The method performs well achieving good linearity over at least 2 orders of magnitude, with coefficients of determination greater than 0.995. The resulting limits of detection are in the range of 0.009-0.092 μg/L. River water samples were successfully analyzed by the proposed method with accuracy in the range of 96-98% and a response time of 15 s, without any further pretreatment or chromatographic separation.     

Specific chemical effects on surface-enhanced Raman spectroscopy for ultra-sensitive detection of biological molecules

Achieving high signal amplification in surface-enhanced Raman scattering (SERS) is important for reaching single molecule level sensitivity and has been the focus of intense research efforts. We introduce a novel chemical enhancer, lithium chloride, that provides an additional order of magnitude increase in SERS relative to previously reported enhancement results. We have duplicated single molecule detection of the DNA base adenine that has previously been reported, thereby providing independent validation of this important result. Building upon this work, we show that the chemical enhancer LiCl produces strong SERS signal under a wide range of experimental conditions, including multiple laser excitation wavelengths and target molecule concentrations, for nucleotides, nucleosides, bases, and dye molecules. This is significant because while selection of anions used in chemical enhancement is well known to affect the degree of amplification attained, cation selection has previously been reported to have no major effect on the magnitude of SERS enhancement. Our findings indicate that cation selection is quite important in ultra-sensitive SERS detection, opening the door to further discussion and theory development involving the role of cations in SERS.     

Determination of peroxide-based explosives using liquid chromatography with on-line infrared detection

A nondestructive analytical method for peroxide-based explosives determination in solid samples is described. Reversed-phase high-performance liquid chromatography in combination with on-line Fourier transform infrared (FT-IR) detection is used for the analysis of triacetonetriperoxide (TATP) and hexamethylenetriperoxide diamine (HMTD). In contrast to other liquid chromatographic methods with optical detection, no derivatization or decomposition of the peroxides is required. The peroxides are identified and quantified via their characteristic absorption spectra in the mid-infrared range of the electromagnetic spectrum. The detection limit of 0.5 mmol L-1 for HMTD and 1 mmol L-1 for TATP allows the identification of the explosives in complex matrixes.     

Optimizing detection sensitivity on surface-enhanced Raman scattering of transition-metal electrodes with confocal Raman microscopy

Some points on how to improve the detection sensitivity of confocal Raman microscopy for the study of surface-enhanced Raman scattering (SERS) of transition-metal electrodes are discussed, including the careful design of the spectroelectrochemical cell, proper selection of the thickness of the solution layer, the binning of charge-coupled device (CCD) pixels, and appropriate setting of the notch filter. Various roughening methods for the Pt, Rh, Fe, Co, and Ni electrode surfaces have been introduced in order to obtain SERS-active surfaces. It has been shown that the appropriate roughening procedure and the optimizing performance of the confocal Raman microscope are the two most important factors to directly generate and observe SERS on net transition-metal electrodes.     

A study of glutathione molecules adsorbed on silver surfaces under different chemical environments by surface-enhanced Raman scattering in combination with the heat-induced sensing method

In this study, surface-enhanced Raman scattering (SERS) in combination with a heat-induced sensing technique has been applied for investigating molecular orientations of glutathione molecules adsorbed on silver colloidal nanoparticles under different chemical environments, which has enabled us to further study how glutathione molecules are adsorbed on the silver surfaces. Factors that may affect the configurations of glutathione molecules adsorbed on the silver nanocolloids have been investigated. By observing the relative enhancement factors of SERS bands due to individual functional groups contributed from different terminals, the affinity between the different functional groups of glutathione and the silver surfaces under different conditions has been sorted and the orientations of glutathione molecules adsorbed on the silver surfaces have been investigated.