Superconductivity in the (Yba2Cu3)1−xNaxO7−δ System

The (YBa₂Cu₃)_1−xNa_xO_7–δ system in the range of x = 0–0.8 was investigated. Experimental data suggest that the sodium doping with x 0.26 does not affect the critical transition temperature T_c, and the crystal structure maintains the orthorhombic lattice with a slightly smaller unit cell. However, sodium doping increases the sintering and grain growth kinetics, resulting in a higher superconducting phase volume and an enhanced Meissner effect. It also lowers the processing temperaturel. The experimental data also suggest that the sodium atoms diffuse into the superconducting YBa₂Cu₃O_7−δ crystallites, which stabilizes the orthorhombic phase. The transition temperature (ortho-rhombic to tetragonal) in sodium-doped materials increases with the increasing concentration of sodium.     

Defect Structure and Electrical Properties of La1−ySryFe1−xAlxO3−δ

La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ perovskites were studied as potential materials for solid-oxide fuel cell (SOFC) cathodes. The phase relations in the LaFeO₃–SrFeO_3−δ–LaAlO₃ system were investigated by X-ray powder diffraction analysis. The defect structure of the La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ perovskites was investigated by Mössbauer spectroscopy and weight-loss analysis. Relations between the nonstoichiometry and the conductivity of the La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ perovskites were investigated. The incorporation of aluminum ( x ) into LaFe_{1− x} Al_xO₃ was found to have no influence on the defect structure but to decrease the conductivity. The incorporation of strontium ( y ) into La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ promotes the formation of anion vacancies and Fe⁴⁺ that lead to higher conductivity.     

Formation Mechanism and Synthesis of Apatite-Type Structure Ba2+xLa8−x(SiO4)6O2−δ

The formation process of Ba₂La₈(SiO₄)₆O₂ was clarified using thermogravimetry–differential thermal analysis (TG-DTA) and a high-temperature powder X-ray diffraction (HT-XRD) method. Phase changes identified from the HT-XRD data surprisingly corresponded to the weight loss and/or endothermic peaks observed in the TG-DTA curves. Raw material with the composition Ba₂La₈(SiO₄)₆O₂ was completely reacted at 1400°C and produced only an apatite-type compound without a secondary phase. Moreover, the synthesis of Ba_{2+ x} La_{8− x} (SiO₄)₆O_2−δ crystals with x = 0–2 was attempted using a solid-state reaction.     

Structural and Dielectric Properties of Ag(Nb0.8Ta0.2)1−xSbxO3 (x≤0.08) Ceramics

Sb₂O₅ were selected to substitute (Nb_0.8Ta_0.2)₂O₅ and the effects of Sb substitution on the dielectric properties of Ag(Nb_0.8Ta_0.2)O₃ ceramics were studied. The perovskite Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics showed no obvious change with x value being no more than 0.08, and the pseudoperovskite unit cell parameters a = c , b and monoclinic angle β decrease with Sb concentration increasing. The dielectric properties of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics were found to be affected greatly by the substitution of Sb for Nb/Ta. The ɛ value of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics sintered at their densified temperature increased from 480 to 825 with x from 0 to 0.08, the tan δ value decreased sharply from 0.0065 to 0.0023 (at 1 MHz) with x increasing from 0 to 0.04, and then kept a stable lower tan δ value ∼0.0024 with x to 0.08. The temperature coefficient of capacitance values continuously decreased from a positive value of 1450 ppm/°C for x =0 to a negative value of −38.52 ppm/°C for x =0.08.     

Influence of Iron Doping on the Microstructure of YBa2(Cu1−xFex)3O7−δ Ceramics

Porosity, grain growth, phase composition, and microstructural defects were studied in sintered YBa₂ (Cu_1−x)₃O_7−x ceramics for x values up to 0.3. The porosity of the samples, related to the sintering mechanism, was independent of iron concentration. A linear dependence of the grain size with the inverse of the iron concentration was found, strongly suggesting grain boundary segregation of iron. The solubility limit was estimated to be x = 0.18 at 950°C in O₂. Beyond this limit, a new microstructural component was found consisting of YBa₂(Cu_1−xFe_x)₃O_7−δ, YBaCuFeO₅ and Ba(Cu,Fe)O₂. The transition from an orthorhombic twin to an orthorhombic tweed phase and a tetragonal phase was detected by polarized light microscopy.     

Preparation and Electrical Properties of New Oxide Ion Conductors Ce6−xGdxMoO15−δ (0.0≤x≤1.8)

A series of oxide ion conductors Ce_{6− x} Gd _x MoO_15−δ (0.0≤ x ≤1.8) have been prepared by the sol–gel method. Their properties were characterized by differential thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), Raman, IR, X-ray photoelectron spectroscopy (XPS), and AC impedance spectroscopy. The XRD patterns showed that the materials were single phase with a cubic fluorite structure. The conductivity of Ce_{6− x} Gd _x MoO_15−δ increases as x increases and reaches the maximum at x =0.15. The conductivity of Ce_4.5Gd_1.5MoO_15−δ is σ_t=3.6 × 10⁻³ S/cm at 700°C, which is higher than that of Ce_4.5/6Gd_1.5/6O_2−δ (σ_t=2.6 × 10⁻³ S/cm), and the corresponding activation energy of Ce_4.5Gd_1.5MoO_15−δ (0.92 eV) is lower than that of Ce_4.5/6Gd_1.5/6O_2−δ (1.18 eV).     

Methane Oxidation on Perovskite-Type Ca(Mn1−xTix)O3−δ

X-ray photoelectron spectroscopy was performed to elucidate the catalytic activity of CH₄ oxidation on perovskite-type Ca(Mn_{1− x} Ti _x )O_3−δ synthesized at 1173 K in a flow of oxygen from a gel with citric acid and ethylene glycol. The Mn ion content decreases and the ratio of the Mn³⁺ ion in the Mn ion increases with increases in x . Ca(Mn_{1− x} Ti _x )O_3−δ has a high catalytic activity of CH₄ oxidation at x =0.4. These results indicate that the catalytic activity strongly depends on the Mn³⁺ ion content of the surface.     

Phase Transitions and Electrical Properties of (Na1−xKx)(Nb1−ySby)O3 Lead-Free Piezoelectric Ceramics With a MnO2 Sintering Aid

Lead-free piezoelectric ceramics (Na_{1− x} K _x )(Nb_{1− y} Sb _y )O₃+ z mol% MnO₂ have been prepared by a conventional solid-state sintering technique. Our results reveal that Sb⁵⁺ diffuses into the K_0.5Na_0.5NbO₃ lattices to form a solid solution with a single-phase orthorhombic perovskite structure. The partial substitution of Sb⁵⁺ for B-site ion Nb⁵⁺ decreases the paraelectric cubic-ferroelectric tetragonal phase transition ( T _c) and the ferroelectric tetragonal-ferroelectric orthorhombic phase transition ( T _O–F), and retains strong ferroelectricity. A small amount of MnO₂ is enough to improve the densification of the ceramics. The co-effects of MnO₂ doping and Sb substitution lead to significant improvements in ferroelectric and piezoelectric properties. The ceramics with x =0.45–0.525, y =0.06–0.08, and z =0.5–1 exhibit excellent ferroelectric and piezoelectric properties: d ₃₃=163–204 pC/N, k _P=0.47–0.51, k _t=0.46–0.52, ɛ=640–1053, tan δ=1.3–3.0%, P _r=18.1–22.6 μC/cm², E _c=0.72–0.98 kV/mm, and T _C=269°–314°C.     

High Q Microwave Dielectric Ceramics in (Ni1−x Znx)Nb2O6 System

(Ni_{1− x} Zn _x )Nb₂O₆, 0≤ x ≤1.0, ceramics with >97% density were prepared by a conventional solid-state reaction, followed by sintering at 1200°–1300°C (depending on the value of x ). The XRD patterns of the sintered samples (0≤ x ≤1.0) revealed single-phase formation with a columbite ( Pbcn ) structure. The unit cell volume slightly increased with increasing Zn content ( x ). All the compositions showed high electrical resistivity (ρ_dc=1.6±0.3 × 10¹¹Ω·cm). The microwave (4–5 GHz) dielectric properties of (Ni_{1− x} Zn _x )Nb₂O₆ ceramics exhibited a significant dependence on the Zn content and to some extent on the morphology of the grains. As x was increased from 0 to 1, the average grain size monotonically increased from 7.6 to 21.2 μm and the microwave dielectric constant (ɛ'_r) increased from 23.6 to 26.1, while the quality factors ( Q _u× f ) increased from 18 900 to 103 730 GHz and the temperature coefficient of resonant frequency (τ_f) increased from −62 to −73 ppm/°C. In the present work, we report the highest observed values of Q _u× f =103 730 GHz, and ɛ'_r=26.1 for the ZnNb₂O₆-sintered ceramics.     

Structure and Microwave Dielectric Characteristics of Ca1+xNd1−xAl1−xTixO4 Ceramics

CaNdAlO₄ microwave dielectric ceramics were modified by Ca/Ti co-substitution, and their dielectric characteristics were evaluated along with their structure and microstructures. Ca_{1+ x} Nd_{1− x} Al_{1− x} Ti _x O₄ ( x =0, 0.025, 0.05, 0.10, 0.15, 0.20) ceramics with the relative density of over 95% theoretical density were obtained by sintering at 1400°–1450°C in air for 3 h, where the K₂NiF₄-type solid solution single phase was determined from the compositions of x <0.20, while a small amount of CaTiO₃ secondary phase was detected for x =0.20. With Ca/Ti co-substitution in CaNdAlO₄ ceramics, the dielectric constant (ɛ_r) increased with increasing x , and the temperature coefficient of resonant frequency (τ_f) was adjusted from negative to positive, while the Q × f ₀ value increased significantly at first and reached an extreme value at x =0.025 and the maximum at x =0.15. The best combination of microwave dielectric characteristics were achieved at x =0.15 (ɛ_r=19.5, Q × f ₀=93 400 GHz, τ_f=−2 ppm/°C). The improvement of the Q × f ₀ value primarily originated from the reduced interlayer polarization with Ca/Ti co-substitution, while the decreased tolerance factor, the subsequent increased interlayer stress, and the appearance of CaTiO₃ secondary phase brought negative effects upon the Q × f ₀ value.     

Aging Behavior of xPb(Fe2/3W1/3)O3· (1 –x)Pb(Fe1/2Nb1/2)O3 Ceramic

The aging behavior of a series of lead perovskite dielectrics with the compositions x Pb(Fe_2/3W_1/3)O₃·(1 – x )Pb(Fe_1/2-Nb_1/2)O₃, where 0 ≤ x ≤ 1, and the effect of dopants were studied. Below the Curie temperature ( T _c), the capacitance and the dissipation factor (tan δ) decrease approximately linearly with logarithmic time. The aging rate depends on the temperature difference, Δ T , between the aging temperature and T _c, and on the dopant concentration, but is independent of the measurement frequency between 1 and 1000 kHz. The maximum aging rate is about 3% per decade of time for capacitance and 5% per decade for tan δ at 1 mol% dopant concentration, and increases to 6.3% for capacitance and 8.5% for tan δ at 0.7 mol% dopant concentration. These results are consistent with an aging mechanism caused by changing ferroelectric domain structure with time, as proposed for BaTiO₃.     

High-Q Microwave Dielectrics in the (Mg1−xCox)2TiO4 Ceramics

The microwave dielectric properties and the microstructures of (Mg_{1− x} Co _x )₂TiO₄ ceramics prepared by the conventional solid-state route were investigated. Lattice parameters were also measured for specimens with different x . The formation of solid solution (Mg_{1− x} Co _x )₂TiO₄ ( x =0.02–0.1) was confirmed by the X-ray diffraction patterns, energy dispersive X-ray analysis, and the lattice parameters measured. By increasing x from 0 to 0.05, the Q × f of the specimen can be tremendously boosted from 150 000 GHz to a maximum of 286 000 GHz. A fine combination of microwave dielectric properties (ɛ_r∼15.7, Q × f ∼286 000 GHz at 10.4 GHz, τ_f∼−52.5 ppm/°C) was achieved for (Mg_0.95Co_0.05)₂TiO₄ ceramics sintered at 1390°C for 4 h. Ilmenite-structured (Mg_0.95Co_0.05)TiO₃ was detected as a second phase. The presence of the second phase would cause no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase. In addition, only a small deviation in the dielectric properties was monitored for specimens with x =0.04–0.05 at 1360°–1420°C. It not only provides a wide process window but also ensures an extremely reliable material proposed as a very promising dielectric for low-loss microwave and millimeter wave applications.     

Electrical Conduction Behavior of La1+xSr1−xGa3O7–δ Melilite-Type Ceramics

Ceramics of the melilite-type compound La_{1+ x} Sr_{1− x} Ga₃O_7−δ were prepared by conventional ceramic processing. Samples prepared represented the entire homogeneity region of the phase (i.e., x =−0.15 to 0.60). Electrochemical characterization under variable temperature and atmospheric conditions in the vicinity of air entailed four-point direct-current conductivity measurements and electromotive force measurements. La_{1+ x} Sr_{1− x} Ga₃O_7−δ samples exhibited a p -type behavior with generally increased conductivity with increased substitution of lanthanum for strontium, which reached a saturation value of ∼10⁻¹ S·cm⁻¹ at 950°C.     

Phase Relations In The Pseudo-Ternary System La2O3–SrO–Fe2O3

The phase relations in the pseudo-ternary system La₂O₃–SrO–Fe₂O₃ have been investigated in air. Isothermal sections at 1100° and 1300°C are presented based on X-ray diffraction and thermal analysis of annealed samples. Extended solid solubility was observed for the compounds Sr _{n +1− v} La _v Fe _n O_{3 n +1−δ} ( n =1, 2, 3, and ∞) and Sr_{1− x} La _x Fe₁₂O₁₉, while only limited solubility of La in Sr_{4− z} La _z Fe₆O_13±δ was observed. At high Fe₂O₃ content, a liquid with low La₂O₃ content was stable at 1300°C.     

Microwave Dielectrics in the (La1/2Na1/2)TiO3–Ca(Fe1/2Nb1/2)O3 System

Dielectric properties of the system (1 − x)(La_1/2Na_1/2)TiO₃– _x Ca(Fe_1/2Nb_1/2)O₃, where 0.4 # x # 0.6, have been investigated at microwave frequencies. The temperature coefficient of resonant frequency (τ_f), nearly 0 ppm/°C, was realized at x = 0.58. These ceramics had perovskite structure and showed relatively low dielectric losses. A new dielectric material applicable to microwave devices having Q · f of 12000–14000 GHz and a dielectric constant (ε_r) of 59–60 has been obtained at 1300–1350°C for 5–15 h sintering.     

Pyrochlore Phases in the System ZnO–Bi2O3–Sb2O5: I. Stoichiometries and Phase Equilibria

Two cubic pyrochlore phases exist in the system ZnO–Bi₂O₃–Sb₂O₅. Neither has the supposed "ideal" stoichiometry, Zn₂Bi₃Sb₃O₁₄. One, P ₁, is a solid solution phase, Zn_{2+ x} Bi_{2.96−( x − y )}Sb_{3.04− y} O_14.04+δ where 0< x <0.13(1), 0< y <0.017(2) and a =10.4285(9)−10.451(1) Å. The other, P ₂, is a line phase, Zn₂Bi_3.08Sb_2.92O_13.92 with a =10.462(2) Å. Subsolidus phase relations at 950°C involving phases P ₁ and P ₂ in the ZnO–Bi₂O₃–Sb₂O₅ phase diagram have been determined.     

Low-Loss Microwave Dielectric Ceramics Using (Mg1−xMnx)2TiO4 (x=0.02–0.1) Solid Solution

Composite ceramics in a solid solution of (Mg_{1− x} Mn _x )₂TiO₄ ( x =0.02–0.1) have been prepared by the mixed oxide route. Formation of the solid solution was confirmed by the X-ray diffraction, the EDX analysis, and the measured lattice parameters, which varied linearly from Mg₂TiO₄ ( a = b = c =8.4410 Å) to (Mg_0.9 Mn_0.1)₂TiO₄ ( a = b = c =8.4445 Å). The XRD analysis also confirmed the co-existence of a cubic-structured (Mg_{1− x} Mn _x )₂TiO₄ and an ilmenite-structured second phase (Mg_{1− x} Mn _x )TiO₃. The composition expected to have a maximum Q × f (276 200 GHz at 10.5 GHz) is (Mg_0.95Mn_0.05)₂TiO₄ with ɛ_r∼15.69 and τ_f∼−52.6 ppm/°C. The existence of the second phase, however, would lead to no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase.     

Porous Glass-Ceramics with a Skeleton of the Fast-Lithium-Conducting Crystal Li1+xTi2−xAlx(PO4)3

Porous glass-ceramics with a skeleton of the fast-lithium-conducting crystal Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ (where x = 0.3–0.5) were prepared by crystallization of glasses in the Li₂O─CaO─TiO₂─Al₂O₃–P₂O₅ system and subsequent acid leaching of the resulting dense glass-ceramics composed of the interlocking of Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ and β-Ca₃(PO₄)₂ phases. The median pore diameter and surface area of the resulting porous Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ glass-ceramics were approximately 0.2 μm and 50 m²/g, respectively. The electrical conductivity of the porous glass-ceramics after heating in LiNO₃ aqueous solution was 8 × 10⁻⁵ S/cm at 300 K or 2 × 10⁻² S/cm at 600 K.     

High-Temperature Creep Behavior of Mixed Conducting La0.5Sr0.5Fe1−xCoxO3-δ (0.5≤x≤1) Materials

Steady-state compressive creep rate of La_0.5Sr_0.5Fe_0.5Co_0.5O_3−δ (LSFC) and La_0.5Sr_0.5CoO_3−δ (LSC) is reported in the temperature region 900°–1050°C and stress range 5–28 MPa. The stress exponents for the two materials were 1.71±0.18 and 1.24±0.15, respectively. The activation energy for creep was considerably higher for LSC (619±56 kJ/mol) than for LSFC (392±28 kJ/mol). The grain size exponent for LSC was 1.28±0.14. Considerably higher creep rates were observed for both materials in N₂ compared with air. Relaxation by creep of chemical-induced stresses in oxygen-permeable membranes is addressed, especially at low partial pressure of oxygen.     

Glass-Free KxBa1−xGa2−xGe2+xO8 Ceramics for Low-Temperature Cofired Ceramics Technology: Synthesis, Phase Transitions, Sintering, and Microwave Dielectric Properties

K _x Ba_{1− x} Ga_{2− x} Ge_{2+ x} O₈ (0.6≤ x ≤1) polycrystalline ceramics are potential materials for glass-free low-temperature cofired ceramics (LTCC) substrates. We have made a comprehensive study of the kinetics of the monoclinic-to-monoclinic P 2₁/ a ⇔ C 2/ m phase transition. The low-temperature-stable P 2₁/ a phase with a high Q × f value was synthesized using a subsolidus method and was well sintered at the LTCC temperature with a H₃BO₃ additive. A good combination of low sintering temperature (910°–920°C), high Q × f values (96 700–104 500 GHz), low permittivities (5.6–6.0), and a small temperature coefficient of resonant frequency (∼−20 ppm/°C) was obtained for ceramics with x =0.67 and 0.9 and with 0.1 wt% of H₃BO₃.