Structural elucidation and iron oxidation states in situ formed β‐Ca3(PO4)2/α‐Fe2O3 composites

A detailed structural analysis on the in situ synthesized β‐Ca₃(PO₄)₂/α‐Fe₂O₃ composites is demonstrated. Compositional ratios, the influence and occupancy of iron at the β‐Ca₃(PO₄)₂ lattice, oxidation state of iron in the composites are derived from analytical techniques involving XRD, FT‐IR, Raman, refinement of the powder X‐ray diffraction and X‐ray photoelectron spectroscopy. Iron exists in the Fe³⁺ state throughout the investigated systems and favors its occupancy at the Ca²⁺(5) site of β‐Ca₃(PO₄)₂ until critical limit, and thereafter crystallizes as α‐Fe₂O₃ at ambient conditions. Fe³⁺ occupancy at the β‐Ca₃(PO₄)₂ lattice yields a Ca₉Fe(PO₄)₇ structure that is isostructural with its counterpart. A strong rise in the soft ferromagnetic behavior of β‐Ca₃(PO₄)₂/α‐Fe₂O₃ composites is obvious that depends on the content of α‐Fe₂O₃ in the composites. Overall, the diverse level of iron inclusions at the calcium phosphate system with a Ca/P ratio of 1.5 yields a structurally stable β‐Ca₃(PO₄)₂/α‐Fe₂O₃ composites with assorted compositional ratios.     

Effects of the preparation methods on the performance of the Cu–Cr–Fe/γ-Al2O3 catalysts for the synthesis of 2-methylpiperazine

Co-precipitation, impregnation and ultrasonic sol–gel (USG) methods have been used to prepare Cu–Cr–Fe/γ-Al₂O₃ catalysts, which were further used to synthesize 2-methylpiperazine. The catalysts were characterized by XRD, XPS, TG/DSC, BET, TPR, AAS and TEM. It is found that preparation method can greatly impact the catalytic performance of the catalysts, the Cu–Cr–Fe/γ-Al₂O₃ catalyst prepared by the ultrasonic sol–gel method proved to be the most active and stable for this reaction. The dispersion and stabilization of Cu⁰ in the reduced catalysts are attributed to the existence of CuCr₂O₄ and Fe₂O₃. A surprising copper migration was detected by XPS analysis for the Cu–Cr–Fe/γ-Al₂O₃-USG catalyst after the calcination process, which may be crucial to the high activity and stability of this catalyst.     

La(1−x)SrxCo1−yFeyO3 perovskites prepared by sol–gel method: Characterization and relationships with catalytic properties for total oxidation of toluene

La_(1−x)Sr_xCo_(1−y)Fe_yO₃ samples have been prepared by sol–gel method using EDTA and citric acid as complexing agents. For the first time, Raman mappings were achieved on this type of samples especially to look for traces of Co₃O₄ that can be present as additional phase and not detect by XRD. The prepared samples were pure perovskites with good structural homogeneity. All these perovskites were very active for total oxidation of toluene above 200 °C. The ageing procedure used indicated good thermal stability of the samples. A strong improvement of catalytic properties was obtained substituting 30% of La³⁺ by Sr²⁺ cations and a slight additional improvement was observed substituting 20% of cobalt by iron. Hence, the optimized composition was La_0.7Sr_0.3Co_0.8Fe_0.2O₃. The samples were also characterized by BET measurements, SEM and XRD techniques. Iron oxidation states were determined by Mössbauer spectroscopy. Cobalt oxidation states and the amount of O⁻ electrophilic species were analyzed from XPS achieved after treatment without re-exposition to ambient air. Textural characterization revealed a strong increase in the specific surface area and a complete change of the shape of primary particles substituting La³⁺ by Sr²⁺. The strong lowering of the temperature at conversion 20% for the La_0.7Sr_0.3Co_(1−y)Fe_yO₃ samples can be explained by these changes. X photoelectron spectra obtained with our procedure evidenced very high amount of O⁻ electrophilic species for the La_0.7Sr_0.3Co_(1−y)Fe_yO₃ samples. These species able to activate hydrocarbons could be the active sites. The partial substitution of cobalt by iron has only a limited effect on the textural properties and the amount of O⁻ species. However, Raman spectroscopy revealed a strong dynamic structural distortion by Jahn–Teller effect and Mössbauer spectroscopy evidenced the presence of Fe⁴⁺ cations in the iron containing samples. These structural modifications could improve the reactivity of the active sites explaining the better specific activity rate of the La_0.7Sr_0.3Co_0.8Fe_0.2O₃ sample. Finally, an additional improvement of catalytic properties was obtained by the addition of 5% of cobalt cations in the solution of preparation. As evidenced by Raman mappings and TEM images, this method of preparation allowed to well-dispersed small Co₃O₄ particles that are very efficient for total oxidation of toluene with good thermal stability contrary to bulk Co₃O₄.     

A zirconium-containing sandwich-type dimer based on trivacant α- and β-[GeW9O34] units, [Zr3O(OH)2(α-GeW9O34)(β-GeW9O34)]

A new zirconium-containing sandwich-type dimer based on trivacant α- and β-[GeW₉O₃₄]¹⁰⁻ units, [Zr₃O(OH)₂(α-GeW₉O₃₄)(β-GeW₉O₃₄)]¹²⁻, was synthesized and characterized by IR spectroscopy, UV electronic spectroscopy and single crystal X-ray diffraction. The central bent of the polyanion contains three oxygen atoms alternating with the three zirconium atoms. The polyanion represents a rare example of the sandwich POMs containing two different isomer subunits.     

Photo-Fenton degradation of 17β-estradiol in presence of α-FeOOHR and H2O2

A novel photocatalyst, α-FeOOH-coated resin (α-FeOOHR), was prepared and applied for the photodegradation of natural estrogen 17β-estradiol (E2) in presence of H₂O₂ under the relatively weak UV irradiation. The continuing loading of ferric oxide on resin was achieved by in situ hydrolysis of Fe³⁺ in alkaline solution. The effects of initial pH, catalyst loading, oxidant concentration and iron leaching on the photodegradation of E2 were investigated. The batch photodegradation experiment showed that high removal efficiency of E2 and fairly good mechanic stability could be obtained by the spherical photocatalyst α-FeOOHR in aqueous solutions. The photodegradation efficiencies slightly decreased with the increase of initial pH in the wide pH range of 3–11. Increase of oxidant and catalyst will enhance photodegradation efficiencies thus lead to increase the Ferric leaching. Neglected iron leaching showed the stability of the loaded α-FeOOH withstanding the oxidation. X-ray photoelectron spectrum (XPS) shed light on the surface activity change of photocatalyst and heterogeneous catalytic essence of this process.     

Self-assembled chloro-bridged metallo-prismatic cations of the general formula [M6(η-C5Me5)6(μ3-tpt)2(μ-Cl)6] (M = Rh, Ir; tpt = 2,4,6-tri(pyridin-4-yl)-1,3,5-triazine)

Two cationic pentamethylcyclopentadienyl metal-based hexanuclear complexes with trigonal prismatic architecture have been synthesised through a two-step strategy. The dinuclear complexes [M(η⁵- C₅Me₅)(μ-Cl)Cl]₂ (M = rhodium and iridium) react with 2,4,6-tri(pyridin-4-yl)-1,3,5-triazine (tpt) in dichloromethane to give the trinuclear complexes [Rh₃(η⁵-C₅Me₅)₃(μ₃-tpt)Cl₆] (1) and [Ir₃(η⁵-C₅Me₅)₃(μ₃-tpt)Cl₆] (2), respectively. Addition of silver triflate to 1 and 2 in dichloromethane connects two identical triangular panels to form the hexanuclear metallo-prismatic cations [Rh₆(η⁵-C₅Me₅)₆(μ₃-tpt)₂(μ-Cl)₆]⁶⁺ (3) and [Ir₆(η⁵-C₅Me₅)₆(μ₃-tpt)₂(μ-Cl)₆]⁶⁺ (4), respectively. Cations 3 and 4 have been isolated as their triflate salts and characterised by ¹H NMR, IR and UV/visible spectroscopy.     

Performance of Pd catalysts supported on nanocrystalline α-Al2O3 and Ni-modified α-Al2O3 in selective hydrogenation of acetylene

Nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ have been prepared by sol–gel and solvothermal methods and employed as supports for Pd catalysts. Regardless of the preparation method used, NiAl₂O₄ spinel was formed on the Ni-modified α-Al₂O₃ after calcination at 1150 °C. However, an addition of NiO peaks was also observed by X-ray diffraction for the solvothermal-made Ni-modified α-Al₂O₃ powder. Catalytic performances of the Pd catalysts supported on these nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ in selective hydrogenation of acetylene were found to be superior to those of the commercial α-Al₂O₃ supported one. Ethylene selectivities were improved in the order: Pd/Ni-modified α-Al₂O₃–sol–gel > Pd/Ni-modified α-Al₂O₃-solvothermal ≈ Pd/α-Al₂O₃–sol–gel > Pd/α-Al₂O₃-solvothermal  Pd/α-Al₂O₃-commerical. As revealed by NH₃ temperature program desorption studies, incorporation of Ni atoms in α-Al₂O₃ resulted in a significant decrease of acid sites on the alumina supports. Moreover, XPS revealed a shift of Pd 3d binding energy for Pd catalyst supported on Ni-modified α-Al₂O₃–sol–gel where only NiAl₂O₄ was formed, suggesting that the electronic properties of Pd may be modified.     

Structure and magnetic properties of Fe1−xCox nanowires in self-assembled arrays

Fe_1−xCo_x nanowires in self-assembled arrays with varying compositions were produced by the template-assisted pulsed electrochemical deposition method. The structural and magnetic properties of the arrays were investigated using several experimental techniques. TEM analyses indicated that the nanowires were regular, uniform, 8 μm in length and 50 nm in diameter. The results of X-ray diffraction indicated that the body-centered-cubic (bcc) (α), face-centered-cubic (fcc) (γ), and hexagonal-close-packed (hcp) () Fe–Co phases appeared in different compositions. Magnetic measurements showed that the coercivity and squareness of the hysteresis loops of the Fe_1−xCo_x changed with their compositions, which may be attributable to shape anisotropy. The room temperature ⁵⁷Fe Mössbauer spectra of the arrays of the Fe_1−xCo_x nanowires revealed strong shape anisotropy.     

Determination of the β ↔ αL′ transition in Ca2SiO4 to 7 KBAR

Differential thermal analysis in hydrostatic apparatus to 7 kbar shows that the β → α_L′ transition temperature in Ca₂SiO₄ linearly increases from 701° ± 2°C at 1 bar at the rate of 10.5 ± 0.5 deg kbar⁻¹. The α_L′ → β transition temperature is observed some 20°–30° lower in temperature than the β → α_L′ transition and no variation in this hysteresis with pressure is indicated.     

Photocatalytic reduction of Ag2SO4 by the Dawson anion α-[P2W18O62] and tetracobalt sandwich complexes

The photocatalytic behaviours of the Dawson salt α-K₆[P₂W₁₈O₆₂] and two isomers of the tetracobalt Dawson-derived sandwich complexes, αββα-Na₁₇[Co₄(H₂O)(OH)(P₂W₁₅O₅₆)₂]·51H₂O·2NaCl and ααβα-Na₁₆[Co₄(H₂O)₂(P₂W₁₅O₅₆)₂]·51H₂O (abbreviated ββ-{Co₄P₄W₃₀} and αβ-{Co₄P₄W₃₀}, respectively), are described and compared.The direct photochemical excitation of the polyoxometalates (POM) in the presence of propan-2-ol as electron donor leads to their reduction. With polyoxometalates as photocatalyst and propan-2-ol as sacrificial electron donor, the reduction of Ag^I₂SO₄ from aqueous solutions is observed leading to metallic Ag_n⁰ clusters and colloidal metal nanoparticles stabilized by POM.In the case of both {Co₄P₄W₃₀}, TEM experiments reveal that most of the Ag_n particles obtained with a slight excess of Ag⁺ are spherical with a quite large distribution in size between 10 and 100 nm.     

Mőssbauer spectra of iron in Ca3SiO5 solid solutions

Mőssbauer spectra have been obtained from C₃S solid solutions containing 0.50 wt % Fe₂O₃ enriched in Fe⁵⁷. After heating in air at 1550°, quenched specimens contain about 9% of this iron as Fe²⁺. The distribution of iron on different sites is inferred from the spectra. Upon annealing the solid solution at 1025°, C₂F exsolves rapidly.     

Improving the oxygen permeability of Ba0.5Sr0.5Co0.8Fe0.2O3−δ membranes by a surface-coating layer of GdBaCo2O5+δ

A GdBaCo₂O_5+δ layer was coated on the Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ membranes to enhance their oxygen permeability by employing the fast oxygen adsorption/desorption surface-exchange properties of the GdBaCo₂O_5+δ material. The oxygen flux of the coated and uncoated Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ membranes was measured in the temperature range of 600–850 °C. The results reveal that the oxygen-permeation flux of the Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ membranes coated by a GdBaCo₂O_5+δ layer shows significant enhancement. The GdBaCo₂O_5+δ layer coated on the oxygen desorption side (He side) has much effect than that coated on the oxygen adsorption side (air side). At 850 °C, the oxygen flux with a single coating layer on the air side can rise 16%, while a single coating on the helium side will result into a rise of 23%.     

Sintering kinetics of α-Al2O3 powder

The sintering kinetics of α-Al₂O₃ powder are reviewed in this paper. The initial sintering of α-Al₂O₃ micropowder and α-Al₂O₃ nanopowder is all controlled by grain boundary diffusion. The sintering kinetics dominate up to a relative density of 0.77, where the coarsening kinetics dominate during further densification. Herring's scaling law can be used to predict the approximate sintering temperature of α-Al₂O₃ powder and demonstrates that if the particle size can be reduced to <20 nm, sintering below 1000°C may be possible. ©     

Sintering of α-Al2O3/quartz, and α-Al2O3/cristobalite related to mullite formation

Cristobalite and quartz react differently in mixtures with α-Al₂O₃ at 1415°C. With cristobalite, an eutectic liquid forms in accordance with the metastable phase equilibrium diagram for α-Al₂O₃-SiO₂ (cristobalite) in the absence of mullite. With quartz, a liquid first forms on the surfaces of quartz because of the occurence of an intermediate liquid phase on transformation of quartz to cristobalite. These liquids act as precursors to the formation of mullite by reacting with α-Al₂O₃. Mullite was detected earlier in the cristobalite-containing mixtures under similar firing conditions because the growth of mullite becomes significant with the formation of the eutectic liquid at the α-Al₂O₃-cristobalite interface since it is already saturated with Al₂O₃. The kinetics of sintering are affected by the rates of the step reactions.     

Decolorization of methylene blue by heterogeneous Fenton reaction using Fe3−xTixO4 (0 ≤ x ≤ 0.78) at neutral pH values

In this work, a series of Fe_3−xTi_xO₄ (0 ≤ x ≤ 0.78) was synthesized using a new soft chemical method. The synthetic Fe_3−xTi_xO₄ were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Mössbauer spectroscopy, thermogravimetric and differential scanning calorimetry (TG–DSC) analyses. The results showed that they were spinel structures and Ti was introduced into their structures.Then, decolorization of methylene blue (MB) by Fe_3−xTi_xO₄ in the presence of H₂O₂ at neutral pH values was studied using UV–vis spectra, dissolved organic carbon (DOC) and element C analyses. Furthermore, the degradation products remained in reaction solution after the decolorization were identified using ionic chromatography (IC), ¹³C nuclear magnetic resonance spectra (NMR), liquid chromatography and mass spectrometry (LC–MS). Although small amounts of MB were mineralized, the aromatic rings in MB were destroyed completely after the decolorization. Decolorization of MB by Fe_3−xTi_xO₄ in the presence of H₂O₂ was promoted remarkably with the increase of Ti content in Fe_3−xTi_xO₄ due to the enhancement of both adsorption and degradation of MB on Fe_3−xTi_xO₄.     

The functionalities of Pt/γ-Al2O3 catalysts in simultaneous HDS and HDA reactions

A Pt/γ-Al₂O₃ catalyst was tested in simultaneous hydrodesulfurization (HDS) of dibenzothiophene and hydrodearomatization (HDA) of naphthalene reactions. Samples of it were subjected to different pretreatments: reduction, reduction–sulfidation, sulfidation with pure H₂S and non-activation. The reduced catalyst presented the best performance, even comparable to that of Co(Ni)Mo catalysts. All catalyst samples were selective to the HDS reaction over HDA, and to the direct desulfurization pathway of dibenzothiophene HDS over the hydrogenation reaction pathway of HDS. The effect of H₂S partial pressure on the functionalities of the reduced Pt/γ-Al₂O₃ catalyst was studied. The results showed that an increase in H₂S partial pressure does not cause poisoning, but an inhibition effect, without changing the catalyst selectivity. Accordingly, the activity trends were ascribed to adsorption differences between the different reactive molecules over the same catalytic active site. TPR characterization along with a thermodynamics analysis showed that the active phase of reduced Pt/γ-Al₂O₃ is constituted by Pt⁰ particles. However, presulfidation of the catalyst leads to a mixture of PtS and Pt⁰ which has a negative effect on the catalytic performance without changing catalyst functionalities.     

Catalytic properties of Ru-η-C6H6-diphosphine complexes for hydrogenation of benzene in aqueous-organic biphasic system

The influences of pH on the catalytic properties of Ru-η⁶-C₆H₆-diphosphine complex [RuCl(η⁶-C₆H₆)(BISBI)]Cl (1) (BISBI = 2,2′-bis(diphenylphosphinomethyl)-1,1′-biphenyl), [RuCl(η⁶-C₆H₆)(BDPX)]Cl (2) (BDPX = 1,2-bis(diphenylphosphinomethyl)benzene), Ru₂Cl₄(η⁶-C₆H₆)₂(μ₂-BDNA) (3) (BDNA = 1,8-bis(diphenylphosphinomethyl)naphthalene), [RuCl(η⁶-C₆H₆)(BISBI)]BF₄ (4), [RuCl(η⁶-C₆H₆)(BDPX)]BF₄ (5), and [(η⁶-C₆H₆)₂Ru₂Cl₂(μ₂-Cl)(μ₂-BDNA)]BF₄ (6) for the hydrogenation of benzene were investigated in aqueous-organic biphasic system. The hydrogenation of benzene catalyzed by all complexes yielded only cyclohexane. The catalytic results revealed that the stabilities of these complexes were not only closely relative with their compositions or molecular structures but also the pH value of aqueous solution. Complexes 1 and 2 were homogeneous catalysts at pH <5, but complexes 3, 4, 5 and 6 were partly decomposed in the same reaction conditions and played simultaneously the roles of homogeneous and heterogeneous catalysts. When the pH was up to 12, all of six complexes were gradually decomposed to Ru(0) particles. The addition of extra phosphine ligand was favorable to prevent these complexes from decomposing in the catalytic process. The experiment of mercury poisoning and the curve of conversion vs time strongly supported above conclusions.     

Size effects on χ- to α-Al2O3 phase transformation

Nano-scaled χ-Al₂O₃ powders with d₅₀ mean particle sizes from 17 to 314 nm were prepared to investigate the size effect on their phase transformation. Structural properties and crystallization behavior as a function of thermal treatments of various-sized χ-Al₂O₃ particles were examined by DTA, XRD and TEM characterizations. It was confirmed that the decrease of particle size allows for stable α-Al₂O₃ formation at relatively low temperature. Furthermore, the phase transformation route of χ-Al₂O₃ to α-Al₂O₃ was also modified due to the decrease of particle size. A critical size of χ-Al₂O₃ that determines the phase transformation behavior was found to be around 40 nm. For particles larger than 40 nm, a transition phase of κ-Al₂O₃ is formed before obtaining final α-Al₂O₃ phase. Nevertheless, for those smaller than the critical size, starting χ-Al₂O₃ particles have to grow to 40 nm and then directly transform to α-Al₂O₃ bypassing κ-Al₂O₃ at a temperature as low as 1050 °C.     

Reductive transformation of 2-nitrophenol by Fe(II) species in γ-aluminum oxide suspension

Fe(II) adsorption onto γ-Al₂O₃ surfaces was studied in view of its high reactivity towards the aqueous reductive transformation of 2-NP. Kinetic measurements demonstrated that rates of 2-NP reduction were highly sensitive to pH, Fe(II) concentration and reaction temperature. An increase in pH, Fe(II) concentration or reaction temperature gave rise to an elevated density of Fe(II) adsorbed to mineral surfaces, which further resulted in an enhanced reaction rate of 2-NP reduction. By using the diffuse double layer (DDL) surface complexation model, the dominant Fe(II) surface complex that was responsible for the high reactivity was predicted to be the strongly bound ≡ SOFe⁺ functional group (represented by ≡ Al_stOFe⁺) onto γ-Al₂O₃ surfaces. In addition, cyclic voltammetry tests showed that the enhanced activity of Fe(II) species was attributed to the negative shift of the redox potential of Fe(III)/Fe(II) couple, resulted from the enhanced concentration of ≡ Al_stOFe⁺ complex.     

Effect of the hydrogen spillover on the selectivity of dibenzothiophene hydrodesulfurization over CoSx/γ-Al2O3, NiSx/γ-Al2O3 and MoS2/γ-Al2O3 catalysts

Dibenzothiophene (DBT) hydrodesulphurization (HDS) reaction at 3 MPa and 325–375 °C on Mo/γ-Al₂O₃ single-bed and Me/γ-Al₂O₃//SiO₂//Mo/γ-Al₂O₃ (Me = Co or Ni) double-bed catalysts were investigated. Results indicate that ratio cyclohexylbenzene (CHB)/biphenyl (BP) or selectivity is higher when using double-beds rather than a single-bed. Synergy in dibenzothiophene hydrodesulphurization on Co//Mo and Ni//Mo double-beds is also detected. Changes in selectivity and conversion are attributed to the action of spillover hydrogen (Hso) formed in the first bed that reaches the second bed.