Effect of CaO doping on corrosion resistance of Cu/(NiFe_2O_4-10NiO) cermet inert anode for aluminum electrolysis

The CaO-doped Cu/(NiFe2O4-10NiO) cermet inert anodes were prepared by the cold isostatic pressing-sintering process, and their corrosion resistance to Na3AlF6-K3AlF6-Al2O3 melt was studied. The results show that the relative density of 5Cu/(NiFe2O4-10NiO) cermet sintered at 1 200 ℃ increases from 82.83% to 97.63% when 2% CaO (mass fraction) is added. During the electrolysis, the relative density of cermet inert anode descends owing to the chemical dissolution of additive CaO at ceramic grain boundary, which...     

Sintering of the NiFe2O4-10NiO/xNi Cermet

The sintering behavior of NiFe2 O4-10NiO/xNi cermet which was used as the most prospective inert anode materials for aluminum electrolysis was studied by examining the effects of raw powder particle size, sintering temperature, and the contents of Ni. The results show that fine particle size enables the powder to have high driving force for sintering. High temperature is beneficial to densification, but the ultra-high temperature does harm to the improvement of the density. The samples of NiFe2O4-10NiO/SNi has the highest relative density of 97.28 % when it is sintered at 1 350 ℃, but it decreases to 95.23 % when sintered at 1 400 ℃. Low addition of Ni has a great help to the sintering of NiFe2 O4-10NiO matrix. When the samples are sintered at 1 350 ℃ and the mass fraction of Ni is 5%, the highest relative density is gained, but the density decreases with the further increase of Ni contents. The low density of the sintered samples of NiFe2 O4-10NiO/17Ni is attributed to the high volume fraction of pores.     

Effect of electrolysis superheat degree on anticorrosion performance of 5 Cu/（10NiO-NiFe2O4） cermet inert anode

5Cu/(10NiO-NiFe2O4) cermet inert anodes were prepared by cold-pressing and sintering process, and the effect of superheat degree of melting K3AlF6-Na3AlF6-AlF3 on their anticorrosion performance was studied under electrolysis conditions. The results show that, the fluctuation of cell becomes small with increasing of superheat degree, which is helpful to inhibit the formation of cathodic encrustation; the concentration of impurities from inert anode in bath goes up to certain degree, but it is far smaller than those in traditional high-temperature bath. Increasing the superheat degree of melting K3AlF6-Na3AlF6-AlF3 has unconspicuous effect on the contents of impurities in cathodic aluminum. The total mass fractions of Fe, Ni and Cu in aluminum are 15.38% and 15.09% respectively under superheat degree of 95 and 195 ℃. From micro-topography of anode used view, increasing the superheat degree can aggravate corrosion of metal Cu in inert anode, and has negative influence on electrical conductivity of electrode to some extent.     

Densification and sintering dynamics of 10NiO-NiFe2O4 composites doped with CaO

The effects of CaO content in the range from 0 to 4.0%, and sintering temperature on the phase composition, relative density and electrical conductivity of 10NiO-NiFe2O4 composites doped with CaO were studied. The results show that there is no change of structure for NiO or NiFe2O4; there is apparent oxygen absorbing and releasing behavior during the heating process in air for 10NiO-NiFe2O4 composites. Introduction of CaO can accelerate the densification of 10NiO-NiFe2O4 composites. The maximum value of relative density is 98.75% for composite doped with 2.0% CaO and sintered at 1 200 ℃, which is beyond about 20% for the undoped composites. The sintering activated energy of sample containing 2% CaO decreases by 15.87 kJ/mol, compared with that of the undoped sample.     

Effect of metallic phase species on the corrosion resistance of 17M/（10NiO-NiFe2O4） cermet inert anode of aluminum electrolysis

1 INTRODUCTIONThere are many disadvantages in the presentaluminumelectrolysis with carbon anode ,such assevere energy consumption,carbon wasting,envi-ronmental pollution and so on.Inert electrode sys-tem can overcome these disadvantages[1 3]. Re-cently ,the researches of the inert anode materialshave mainly been concentrated on alloys[4]and cer-met materials[5 ,6]. NiFe2O4based cermets , whichpossess not only high electrical conductivity ofmetal but also good corrosion resistance of cera…     

The prefer red-site tendency of alloying element Nb in Fe γ phase and its effect on grain boundary cohesion

The discrete variational (DV) and DMol methods within the framework of density functional theory are used to study the effect of alloying element Nb on Fe γ phase. The impurity formation energy in bulk and segregation energies at grain boundary and free surface are calculated. The results show that Nb prefers to segregate at grain boundary. The difference in segregation energies between the grain boundary and the corresponding free surface is - 0.39 eV for solute Nb. According to Rice-Wang model, it can be predicted that Nb can enhance grain boundary cohesion. The calculated results of interatomic energy and charge density show that charge would be redistributed, and the bonds across grain boundary are strengthened by the substitution of Nb for Fe. As a result, it is difficult for the grain boundary to move. Thus the dragging effect of Nb is explained electronically.     

Fabrication and anodic polarization behavior of lead-based porous anodes in zinc electrowinning

A new type of lead-based porous anode in zinc electrowinning was prepared by negative pressure infiltration. The anodic polarization potential and corrosion rate were studied and compared with those of traditional fiat anodes （Pb-0.8%Ag） used in industry. The anode corrosion rate was determined by anode actual current density and microstructure. The results show that the anodic oxygen evolution potential decreases first and then increases with the decrease of pore diameter. The anodic potential decreases to the lowest value of 1.729 V at the pore diameter of 1.25-1.60 mm. The porous anode can decrease its actual current density and thus decrease the anodic corrosion rate. When the pore diameter is 1.60-2.00 mm, the anodic relative corrosion rate reaches the lowest value of 52.1%.     

Preparation and electrochemical properties of Pb-0.3wt%Ag/Pb-WC composite inert anodes

We prepared Pb-0.3wt%Ag/Pb-WC(WC stands for tungsten carbide,the same below) composite inert anodes by double-pulse electrodeposition on the surface of Pb-0.3wt%Ag substrates,and investigated the electrochemical properties of the composite inert anodes,which were obtained under different forward pulse average current densities from 2 A/dm~2 to 5 A/dm~2 and WC concentrations from 0 g/L to 40 g/L in bath.The kinetic parameters of oxygen evolution,corrosion potential and corrosion current of the composite inert anodes were obtained in a synthetic zinc electrowinning electrolyte of 50 g/L Zn~(2+) and 150 g/L H_2SO_4 at 35 ℃,by measuring the anodic polarization curves,Tafel polarization curves and cyclic voltammetry curves.The results show that Pb-0.3wt% Ag/Pb-WC composite inert anodes obtained under forward pulse average current density of 3 A/dm~2 and WC concentration of 30 g/L in an original acid plating bath,possess higher electrocatalytic activity of oxygen evolution,lower overpotential of oxygen evolution,better reversibility of electrode reaction and corrosion resistance in [ZnSO_4+H_2SO_4] solution.The overpotential of oxygen evolution of the composite inert anode is 0.926 V under 500 A/m~2 in [ZnSO_4+H_2SO_4] solution,and 245 mV lower than that of Pb-1% Ag alloy;the corrosion current of the composite inert anode is 0.95×10~(-4)A which is distinctly lower than that of Pb-1%Ag alloy,showing the excellent corrosion resistance.     

Microstructure and mechanical properties of TiB<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites

Effects of Al2O3 and Ni as the additives on the sinterability, microstructure and mechanical properties were systematic studied. The experimental results show that only a relative density about 96.2% of hot-pressing TiB2-30%Al2O3 can be attained due to the plate-like TiB2 particle and its random orientation and excessive Al2O3 grain growth. When sintering temperature is higher than 1 700 ℃, TiB2 grain growth can be found, which obvious improves flexural strength of TiB2 matrix but decreases toughness. It seems that mechanical properties of TiB2-Al2O3 composites are mainly depended on relative density besides grain growth. otherwise, they will be determined by relative density and TiB2 matrix strength together. Anyway, Al2O3 addition can weaken the grain boundary and thus improve the toughness of the materials. A flexural strength of 529 MPa, Vickers hardness of 24.8 GPa and indentation toughness of 4.56 MPa·m1/2 can be achieved inTiB2-30vol% Al2O3.     

Corrosion Behavior of Cu/Ni Coatings on Ti-6Al-4V Alloy after Diffused Treatment

To improve the low thermal conductivities and poor wear resistances of TC4(Ti-6Al-4V) alloy, the most widely used titanium alloy, the surface of TC4 alloys is modified by electroplating deposition of Ni and Cu layers, and then heat-treated to increase the diffusivity at the interface. In this paper, the corrosion behavior of Cu/Ni coatings on TC4 alloy at different heat treatment processes was investigated in 3.5 wt% Na Cl by the electrochemical analysis, and the microstructure and composition of corrosion products was carried out to reveal the corrosion resistance mechanism of Cu/Ni coatings. It was found that the corrosion resistance was significantly influenced by heat treatment temperature. With the increasing diffusion treatment temperature from 500 to 700 ℃, the corrosion potential positively shifted from -330.87 to-201.14 m V, and the corrosion current density decreased from 4.02×10~(-3) to 0.514×10~(-3) m A/cm~2. However, when heat treatment temperature increased to 800 ℃, the corrosion potential negatively shifted to-207.21 m V, and the current density increased to 1.62×10-3 m A/cm~2.The diffusion behavior of Ti, Ni and Cu elements occurred and small amounts of Ni and Ti elements appeared on the specimen surface under different heat treatment temperature. Especially heattreated at 700 ℃, the smaller pore size, dense Cu_2O film, and highly stable Ti O and Ni O oxide layer were formed, which dramatically enhanced the corrosion resistance of Cu/Ni coatings. Finally, a novel model of corrosion resistance was proposed based on the analysis mentioned above.     

Preparation and properties of 4.25Cu-0.75Ni／NiFe2O4 cermet

4.25Cu-0.75Ni/NiFe₂O₄ cermets were prepared by doping NiFe₂O₄ ceramic matrix with the mixed powders of Cu and Ni or Cu-Ni alloy powder as the electrical conducting metallic elements. The effects of technological parameters, such as the adding modes of metallic elements, the ball milling time, the sintering time and the sintering temperature, on the relative density and resistivity of the cermets were studied. The results show that the resistivity of 4.25Cu-0.75Ni/NiFe₂O₄ cermets decreases with increasing temperature, and has a turning point at 590 °C, which is similar to that of NiFe₂O₄ ceramic. The sintering temperature and adding modes of metallic elements have a great influence on the properties of 4.25Cu-0.75Ni/NiFe₂O₄ cermets. When the sintering temperature increases from 1200 °C to 1300 °C, the relative density increases from 89.86% to 95.33%, and the resistivity at 960 °C decreases from 0.11 Ω · cm to 0.03 Ω · cm, respectively. When the metallic elements are added with the mixed powders of Cu and Ni, the cermets of finely and uniformly dispersed metallic phase, high density and electric conductivity are obtained. The relative density and resistivity at 960 °C are 90.23% and 0.04 Ω · cm respectively for the cermet samples sintered at 1200 °C for 2 h, which are both better than those of the cermets prepared under the same technique conditions but with the metallic elements added as 85Cu-15Ni alloy powders. Foundation item: Project (G1999064903) supported by the National Key Fundamental Research and Development Program of China; project(2001AA335013) supported by the National High Technology Research and Development Program of China; project (50204014) supported by the National Natural Science Foundation of China     

Electrical conductivity of Cu/（10NiO-NiFe2O4） cermet inert anode for aluminum electrolysis

Cu/(10NiO-NiFe2O4) cermets containing mass fractions of Cu of 5%, 10%, 15% and 20% were prepared, and their electrical conductivities were measured at different temperatures. The effects of temperature and content of metal Cu on the electrical conductivity were investigated especially. The results indicate that the metallic phase Cu distributes evenly in 10NiO-NiFe2O4 ceramic matrix. The mechanism of electrical conductivity of Cu/(10NiO-NiFe2O4) cermets obeys the rule of electrical mechanism of semiconductor, the electrical conductivity for cermet containing 5% Cu increases from 2.70 to 20.41 S/cm with temperature increasing from 200 to 900 ℃. The change trend of electrical conductivity with temperature is similar with each other and it increases with increasing temperature and content of metal Cu. At 960 ℃, the electrical conductivity of cermet increases from 2.88 to 82.65 S/cm with the content of metal Cu increasing from 0 to 20%.     

Corrosion resistance of plasma sprayed NiCrAl+(ZrO2+Y2O3) thermal barrier coating on 18-8 steel surface

The corrosion resistance of NiCrAl+(ZrO₂+Y₂O₃) thermal barrier coating, formed with the plasma spraying technique, on the 18 - 8 steel surface was investigated. The phase structure and morphology of the coating were analyzed by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical corrosion behavior of the coating in 1.0 mol/L H₂SO₄ solution was studied by using electrochemical measurement methods. The results show that the gradient plasma spraying coating is composed of the NiCrAlY coating and the (ZrO₂+Y₂O₃) top coating, and the coating thickness is 360 μm. The microhardness of coating reaches 1 100 HV. The corrosion resistance of the plasma sprayed coating of the 18 - 8 steel surface is about 5 times as great as that of the original pattern. The corrosion resistance of the coating is enhanced notably. Foundation item: Project (5040202140) supported by Scientific Research Common Program of Beijing Municipal Commission of Education     

Antibiotic properties of Al2O3 doping silver

The preparation technique and properties of Ag-type inorganic antibiotic material carried by Al₂O₃ were studied. The results show that the material has good antibiotic and safety properties, the acute toxicity taken by stomata is LD ₅₀>8 000 mg/kg (little and big white rats), and the normal quantity in subacute toxicity test is 80 mg/(kg · d). The better mass fraction of doping Ag₂O in antibiotic material carried by Al₂O₃ is 4%–8%, and the optimal sintering temperature is from 1 000 °C to 1 100 °C. Foundation item: Project (2002AA327090) supported by National High Technology Research and Development Program of China     

Electrical conductivity of （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts

The effects of contents of AlF3 and Al2O3, and temperature on electrical conductivity of （Na3AlF6-40%K3AlF6）- AlF3-Al2O3 were studied by continuously varying cell censtant （CVCC） technique. The results show that the conductivities of melts increase with the increase of temperature, but by different extents. Every increasing 10 ℃ results in an increase of 1.85 × 10^-2, 1.86× 10^-2, 1.89 × 10^-2 and 2.20 × 10^-2 S/cm in conductivity for the （Na3AlF6-40%K3AlF6）-AlF3 melts containing 0%, 20%, 24%, and 30% AlF3, respectively. An increase of every 10 ℃ in temperature results an increase about 1.89× 10^-2, 1.94 × 10^-2, 1.95 × 10^-2, 1.99× 10^-2 and 2.10× 10^-2 S/cm for （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts containing 0%, 1%, 2%, 3% and 4% Al2O3, respectively. The activation energy of conductance was calculated based on Arrhenius equation. Every increasing 1% of AlF3 results in a decrease of 0.019 and 0.020 S/cm in conductivity for （Na3AlF6-40%K3AlF6）-AlF3 melts at 900 and 1 000 ℃, respectively. Every increase of 1% Al2O3 results in a decrease of 0.07 S/cm in conductivity for （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts. The activation energy of conductance increases with the increase in content of AlF3 and Al2O3.