Separation and capture of carbon dioxide from CO2/H2 syngas mixture using semi-clathrate hydrates

The relation between anthropogenic emissions of CO₂ and its increased levels in the atmosphere with global warming and climate change has been well established and accepted. Major portion of carbon dioxide released to the atmosphere, originates from combustion of fossil fuels. Integrated gasification combined cycle (IGCC) offers a promising fossil fuel technology considered as a clean coal-based process for power generation particularly if accompanied by precombustion capture. The latter includes separation of carbon dioxide from a synthesis gas mixture containing 40 mol% CO₂ and 60 mol% H₂.A novel approach for capturing CO₂ from the above gas mixture is to use gas hydrate formation. This process is based on selective partition of CO₂ between hydrate phase and gas phase and has already been studied with promising results. However high-pressure requirement for hydrate formation is a major problem.We have used semiclathrate formation from tetrabutylammonium bromide (TBAB) to experimentally investigate CO₂ capture from a mixture containing 40.2 mol% of CO₂ and 59.8 mol% of H₂. The results shows that in one stage of gas hydrate formation and dissociation, CO₂ can be enriched from 40 mol% to 86 mol% while the concentration of CO₂ in equilibrium gas phase is reduced to 18%. While separation efficiency of processes based on hydrates and semi-clathrates are comparable, the presence of TBAB improves the operating conditions significantly. Furthermore, CO₂ concentration could be increased to 96 mol% by separating CO₂ in two stages.     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

Sonosynthesis of nanostructured TiO2 doped with transition metals having variable bandgap

Here is described a sonosynthesis method to produce nanostructured TiO₂ pure and doped (Al, C, Co, Fe and Rh). The synthesized TiO₂ is amorphous and is transformed to anatase, brookite or rutile by heat treatments at temperatures between 100 and 300 °C. Pure TiO₂ can be partially transformed to brookite between 100 and 300 °C. The band gap in all heat treated samples from 100–600 °C is relatively constant, 3.2 eV, except for those doped with Fe. This effect on the band gap is the results of a bi/tri-crystal (anatase:brookite:rutile) framework. Rhodium is the most effective dopant to narrow the band gap, the opposite effect is observed with C. In single phase frameworks the bandgap can be modified ranges from 2.38 to 4.10 eV depending on the dopant. TiO₂ lattices are rigid enough to promote an outwards diffusion of the dopants to the surface of the particles forming nanostructured precipitates. The precipitates develop a network of quantum-dots with sizes between 5 and 10 nm.     

Effect of TiO2 particle size on the photocatalytic reduction of CO2

Pure TiO₂ anatase particles with a crystallite diameters ranging from 4.5 to 29 nm were prepared by precipitation and sol–gel method, characterized by X-ray diffraction (XRD), BET surface area measurement, UV–vis and scanning electron microscopy (SEM) and tested in CO₂ photocatalytic reduction. Methane and methanol were the main reduction products. The optimum particle size corresponding to the highest yields of both products was 14 nm. The observed optimum particle size is a result of competing effects of specific surface area, charge–carrier dynamics and light absorption efficiency.     

Preparation of nanosized anatase TiO2-coated kaolin composites and their pigmentary properties

Nanosized anatase TiO₂-coated kaolin composites were prepared by the chemical deposition method starting from calcined kaolin and TiCl₄. The resultant TiO₂ nanoparticles on the kaolin surfaces existed in anatase phase after calcination at 200, 400, and 900 °C for 1 h, respectively. The surfaces of the kaolin powders were uniformly coated by a monolayer of TiO₂ nanoparticles. The higher calcination temperature was beneficial to formation of well crystallized anatase TiO₂ nanoparticles. The light scattering indexes of the TiO₂-coated calcined kaolin composites were two times higher than that of the kaolin substrate. XPS analysis shows that TiO₂ coating layers anchored at the kaolin surfaces via the Ti-O-Si and Ti-O-Al bonds.     

Calcination and sintering characteristics of limestone under O2/CO2 combustion atmosphere

The O₂/CO₂ coal combustion technology is an innovative combustion technology that can control CO₂, SO₂ and NO_x emissions simultaneously. Calcination and sintering characteristics of limestone under O₂/CO₂ atmosphere were investigated in this paper. The pore size, the specific pore volume and the specific surface area of CaO calcined were measured by N₂ adsorption method. The grain size of CaO calcined was determined by XRD analysis. The specific pore volume and the specific surface area of CaO calcined in O₂/CO₂ atmosphere are less than that of CaO calcined in air at the same temperature. And the pore diameter of CaO calcined in O₂/CO₂ atmosphere is larger than that in air. The specific pore volume and the specific surface area of CaO calcined in O₂/CO₂ atmosphere increase initially with temperature, and then decline as temperature exceeds 1000 °C. The peaks of the specific pore volume and the specific surface area appear at 1000 °C. The specific surface area decreases with increase in the grain size of CaO calcined. The correlations of the grain size with the specific surface area and the specific pore volume can be expressed as L = 744.67 + 464.64 lg(1 / S) and L = − 608.5 + 1342.42 lg(1 / ε), respectively. Sintering has influence on the pore structure of CaO calcined by means of influencing the grain size of CaO.     

High-pressure sorption isotherms and sorption kinetics of CH4 and CO2 on coals

Using a manometric experimental setup, high-pressure sorption measurements with CH₄ and CO₂ were performed on three Chinese coal samples of different rank (VR_r = 0.53%, 1.20%, and 3.86%). The experiments were conducted at 35, 45, and 55 °C with pressures up to 25 MPa on the 0.354-1 mm particle fraction in the dry state. The objective of this study was to explore the accuracy and reproducibility of the manometric method in the pressure and temperature range relevant for potential coalbed methane (CBM) and CO₂-enhanced CBM (CO₂-ECBM) activities (P > 8 MPa, T > 35 °C). Maximum experimental errors were estimated using the Gauss error propagation theorem, and reproducibility tests of the high-pressure sorption measurements for CH₄ and CO₂ were performed. Further, the experimental data presented here was used to explicitly study the CO₂ sorption behaviour of Chinese coal samples in the elevated pressure range (up to 25 MPa) and the effects of temperature on supercritical CO₂ sorption isotherms.The experiments provided characteristic excess sorption isotherms which, in the case of CO₂ exhibit a maximum around the critical pressure and then decline and level out towards a constant value. The results of these manometric tests are consistent with those of previous gravimetric sorption studies and corroborate a crossover of the 35, 45, and 55 °C CO₂ excess sorption isotherms in the high-pressure range. The measurement range could be extended, however, to significantly higher pressures. The excess sorption isotherms tend to converge, indicating that the temperature dependence of CO₂ excess sorption on coals at high-pressures (>20 MPa) becomes marginal. Further, all CO₂ high-pressure isotherms measured in this study were approximated by a three-parameter excess sorption function with special consideration of the density ratio of the “free” phase and the sorbed phase. This function provided a good representation of the experimental data.The maximum excess sorption capacity of the three coal samples for methane ranged from 0.8 to 1.6 mmol/g (dry, ash-free) and increased from medium volatile bituminous to subbituminous to anthracite. The medium volatile bituminous coal also exhibited the lowest overall excess sorption capacity for CO₂. However, the subbituminous coal was found to have the highest CO₂ sorption capacity of the three samples. The mass fraction of adsorbed substance as a function of time recorded during the first pressure step was used to analyze the kinetics of CH₄ and CO₂ sorption on the coal samples. CO₂ sorption proceeds more rapidly than CH₄ sorption on the anthracite and the medium volatile bituminous coal. For the subbituminous coal, methane sorption is initially faster, but during the final stage of the measurement CO₂ sorption approaches the equilibrium value more rapidly than methane.     

An economic feasibility study of O2/CO2 recycle combustion technology based on existing coal-fired power plants in China

In order to reduce the CO₂ emission from the coal-fired power plants, O₂/CO₂ recycle combustion (Oxy-combustion) technique has been proposed through combining a conventional combustion process with a cryogenic air separation process. The technique is capable of enriching CO₂ concentration and then allowing CO₂ sequestration in an efficient and energy-saving way. Taking into account the CO₂ taxation and CO₂ sale, the paper evaluates the economic feasibility of Oxy-combustion plants retrofitted from two typical existing conventional coal-fired power plants (with capacities of 2 × 300 MW and 2 × 600 MW, respectively) with Chinese data. The cost of electricity (COE) and the CO₂ avoidance cost (CAC) are also considered in the evaluation. The COE of the retrofitted Oxy-combustion plant is nearly the same as that of the corresponding conventional plant if the unit price of CO₂ sale reaches 17-22 $/t (different cases). The CAC of the retrofitted 2 × 300 MW Oxy-combustion plant is 1-3 $/t bigger than that of the retrofitted 2 × 600 MW Oxy-combustion plant. Supercritical plants are more economical and appropriate for Oxy-combustion retrofit. The result indicates that Oxy-combustion technique is not only feasible for CO₂ emission control based on existing power plants but is also cost-effective.     

Onset coarsening-coalescence kinetics of ZrO2 and less refractory TiO2 nanoparticles: Effect of homologous temperature and phase transformation

Specific surface area change of ZrO₂ (predominant tetragonal - (t) symmetry, 30-50 nm) and less refractory TiO₂ anatase nanoparticles (20-50 nm) upon isothermal firing at 700-1000 °C in air was determined by N₂ adsorption-desorption hysteresis isotherm. The nanoparticles underwent onset coarsening-coalescence within minutes without appreciable phase transformation for TiO₂, but with extensive transformation into monoclinic (m-) symmetry for ZrO₂. The apparent activation energy of such a process being not much higher for ZrO₂ (77 ± 23 kJ/mol) than TiO₂ (56 ± 3 kJ/mol) nanoparticles can be attributed to transformation plasticity. The minimum temperature for coarsening/coalescence of the present ZrO₂ and TiO₂ nanoparticles was estimated as 710 and 641 °C, respectively.     

Synthesis of a TiO2 ceramic membrane containing SrCo0.8Fe0.2O3 by the sol-gel method with a wet impregnation process for O2 and N2 permeation

A SrCo_0.8Fe_0.2O₃ impregnated TiO₂ membrane (TiO₂-SrCo_0.8Fe_0.2O₃ membrane) was successfully prepared using a sol-gel method in combination with a wet impregnation process. The membrane was subjected to a single gas permeance test using oxygen (O₂) and nitrogen (N₂). The TiO₂ membrane was immersed in the SrCo_0.8Fe_0.2O₃ solution, dried and then calcined to affix SrCo_0.8Fe_0.2O₃ into the membrane. The effect of the acid/alkoxide (H⁺/Ti⁴⁺) molar ratio of the TiO₂ sol on the TiO₂ phase transformation was investigated. The optimal molar ratio was found to be 0.5, which resulted in nanoparticles with a mean size of 5.30 nm after calcination at 400 °C. The effect of calcination temperature on the phase transformation of TiO₂ and SrCo_0.8Fe_0.2O₃ was investigated by varying the calcination temperature from 300 to 500 °C. X-ray diffraction spectroscopy (XRD) and Fourier transform infrared (FTIR) analysis confirmed that a calcination temperature of 400 °C was preferable for preparing a TiO₂-SrCo_0.8Fe_0.2O₃ membrane with fully crystallized anatase and SrCo_0.8Fe_0.2O₃ phases. The results also showed that polyvinyl alcohol (PVA) and hydroxypropyl cellulose (HPC) were completely removed. Field emission scanning electron microscopy (FESEM) analysis results showed that a crack-free and relatively dense TiO₂ membrane (∼0.75 μm thickness) was created with a multiple dip-coating process and calcination at 400 °C. The gas permeation results show that the TiO₂ and TiO₂-SrCo_0.8Fe_0.2O₃ membranes exhibited high permeances. The TiO₂-SrCo_0.8Fe_0.2O₃ membrane developed provided greater O₂/N₂ selectivity compared to the TiO₂ membrane alone.     

Shock-consolidated TiO2 bulk with pure anatase phases fabricated by explosive compaction using underwater shockwave

Titanium dioxide (TiO₂) bulk with pure anatase phases was fabricated by an explosive compaction technique using an underwater shockwave. Dynamic shock pressure of 6 GPa was used to consolidate anatase TiO₂ powders. Its microstructural, crystalline structural and photocatalytic characteristics were observed and measured by various techniques, such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and photocatalytic activity measurement system. It was confirmed that the relative density of anatase TiO₂ compact is about 96% (3.73 g/cm³) of the theoretical density (3.89 g/cm³) and a strong surface bonding between particles is formed by a shock energy. In X-ray diffraction analysis, high purity anatase phases, broadened peaks due to lattice defects and decreased crystallite size were found. For the photocatalytic activities, the anatase TiO₂ compact was quite excellent compared to the commercial sintered TiO₂ bulk.     

Anatase TiO2 spheres with high surface area and mesoporous structure via a hydrothermal process for dye-sensitized solar cells

Spherical pure anatase TiO₂ spheres with a mesoporous structure and high surface area of up to 116.5 m² g⁻¹ were prepared by a simple urea-assisted hydrothermal process and investigated as dye-sensitized solar-cell electrodes. Although the particle diameters of the prepared TiO₂ spheres ranged from 0.4 to 1.3 μm, due to the high specific surface area, mesoporous TiO₂ sphere electrode was obtained with enhanced light harvesting and a larger amount of dye loading. An overall light conversion efficiency of 7.54% under illumination of simulated AM 1.5G solar light (100 mW cm⁻²) was achieved using the mesoporous TiO₂ spheres electrode, which was significantly higher than a commercial Degussa P25 TiO₂ nanocrystals electrode (5.69%).     

Gasoline-range hydrocarbon synthesis over Co/SiO2/HZSM-5 catalyst with CO2-containing syngas

Selective synthesis of gasoline-range hydrocarbons (C₅-C₁₂) was investigated in a fixed-bed micro reactor using two series of CO₂-containing syngas with various mole CO₂/(CO + CO₂) and H₂/(CO + CO₂) ratios, where Fischer-Tropsch synthesis(FTS) and in situ hydrocracking/hydroisomerization were performed over bifunctional Co/SiO₂/HZSM-5 catalyst. CO₂ was converted at 0.15-0.55 of CO₂/(CO + CO₂) ratio under H₂-rich condition (H₂/(CO + CO₂) = 2.0), highest conversion of 20.3% at 0.42. Further increasing CO₂ content decreased CO₂ conversion and quite amount of CO₂ acted as diluting component. For the syngas with low H₂ content or H₂/(CO + CO₂) ratio(< 1.85, H₂/CO = 2.0), the competitive adsorption of CO, H₂ and CO₂ resulted in low CO, CO₂ and total carbon conversion, which was 57.9%, 12.7% and 31.4% respectively at 0.74 of H₂/(CO + CO₂) ratio(H₂/CO/CO₂/N₂ = 40.8/20.4/34.8/4). FTS results indicated that high H₂ content and proper H₂/(CO + CO₂) ratio were favorable for the conversion of CO₂-containing syngas. More than 45% selectivity to gasoline-range hydrocarbons including isoparaffins was obtained under the two series of syngas. It was also tested that the catalytic activity of Co/SiO₂/HZSM-5 kept stable under CO₂-containing syngas(< 7.5%). And the quick catalytic deactivation under high CO₂ containing syngas(H₂/CO/CO₂/N₂ = 45.3/23.2/27.1/3.06) was due to carbon deposition and pore blockage by heavy hydrocarbon, tested by thermal gravimetry, N₂ physisorption and scanning electron microscopy(SEM).     

Effect of TiO2 supporting layer on Fe2O3 photoanode for efficient water splitting

For an electrochemical water splitting system, titanate nanotubular particles with a thickness of ∼700 nm produced by a hydrothermal process were repetitively coated on fluorine-doped tin oxide (FTO) glass via layer-by-layer self-assembly method. The obtained titanate/FTO films were dipped in aqueous Fe solution, followed by heat treatment for crystallization at 500 °C for 10 min in air. The UV–vis absorbance of the Fe-oxide/titanate/FTO film showed a red-shifted spectrum compared with the TiO₂/FTO coated film; this red shift was achieved by the formation of thin hematite-Fe₂O₃ and anatase-TiO₂ phases verified using X-ray diffraction and Raman results. The cyclic voltammetry results of the Fe₂O₃/TiO₂/FTO films showed distinct reversible cycle characteristics with large oxidation–reduction peaks with low onset voltage of I–V characteristics under UV–vis light illumination. The prepared Fe₂O₃/TiO₂/FTO film showed much higher photocurrent densities for more efficient water splitting under UV–vis light illumination than did the Fe₂O₃/FTO film. Its maximum photocurrent was almost 3.5 times higher than that obtained with Fe₂O₃/FTO film because of the easy electron collection in the current collector. The large current collection was due to the existence of a TiO₂ base layer beneath the Fe₂O₃ layer.     

Pulverized coal combustion in air and in O2/CO2 mixtures with NOx recycle

This paper presents experimental results of a 20 kW vertical combustor equipped with a single pf-burner on pulverised coal combustion in air and O₂/CO₂ mixtures with NO_x recycle. Experimental results on combustion performance and NO_x emissions of seven international bituminous coals in air and in O₂/CO₂ mixtures confirm the previous findings of the authors that the O₂ concentration in the O₂/CO₂ mixture has to be 30% or higher to produce matching temperature profiles to those of coal-air combustion while coal combustion in 30% O₂/70% CO₂ leads to better coal burnout and less NO_x emissions than coal combustion in air. Experimental results with NO_x recycle reveal that the reduction of the recycled NO depends on the combustion media, combustion mode (staging or non-staging) and recycling location. Generally, more NO is reduced with coal combustion in 30% O₂/70% CO₂ than with coal combustion in air. Up to 88 and 92% reductions of the recycled NO can be achieved with coal combustion in air and in 30% O₂/70% CO₂ respectively. More NO is reduced with oxidant staging than without oxidant staging when NO is recycled through the burner. Much more NO is reduced when NO recycled through the burner (from 65 to 92%) than when NO is recycled through the staging tertiary oxidant ports (from 33 to 54%). The concentration of the recycled NO has little influence on the reduction efficiency of the recycled NO with both combustion media—air and 30% O₂/70% CO₂.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

CO oxidation and CO2 reduction on carbon supported PtWO3 catalyst

The activity of a carbon supported PtWO₃ (PtWO₃/C) catalyst in the CO oxidation and CO₂ reduction reactions was evaluated in sulfuric acid solution at room temperature.Cyclic voltammetry combined with on-line mass spectrometry shows that the oxidation of both saturated CO adlayer and dissolved CO on PtWO₃/C material commences at rather low potentials, ca. 0.18 and 0.12 V vs. RHE, respectively. However, the low-potential process seems to involve only a minor fraction of the CO adlayer, the major part of the adsorbed CO layer being oxidised at the potentials as high as those for pure Pt catalysts—ca. 0.7 V vs. RHE. PtWO₃/C material was found to reversibly de-activate upon a prolonged exposure to the CO-saturated solution due to the inhibition of the hydrogen tungsten bronze formation.The reduction of CO₂ on PtWO₃/C leads to the formation of an adsorbate - presumably CO - on the Pt sites of the catalyst. Although the rate of the adsorbate build-up on PtWO₃/C at 0.1 V is lower than that on pure Pt/C, our results indicate that upon a prolonged exposure of the PtWO₃/C electrode to a CO₂-saturated solution a complete poisoning of the Pt sites with the adsorbate is likely to occur at room temperature.     

Photocatalytic functional coatings of TiO2 thin films on polymer substrate by plasma enhanced atomic layer deposition

We prepared photocatalytic TiO₂ thin films which exhibited relatively high growth rate and low impurity on polymer substrate by plasma enhanced atomic layer deposition (PE-ALD) from Ti(NMe₂)₄ [tetrakis (dimethylamido) Ti, TDMAT] and O₂ plasma to show the self-cleaning effect. The TiO₂ thin films with anatase phase and bandgap energy about 3.3 eV were deposited at growth temperature of 250 °C and the photocatalytic effects were compared with commercial Activ glass. From contact angles measurement of water droplet and photo-induced degradation test of organic liquid, TiO₂ thin films with anatase phases showed superhydrophilic phenomena and decomposed organic liquid after UV irradiation. The anatase TiO₂ thin film on polymer substrate showed highest photocatalytic efficiency after 5 h UV irradiation. We attribute the highest photocatalytic efficiency of TiO₂ thin film with anatase structure to the formation of suitable crystalline phase and large surface area.     

TiO2 photocatalyst loaded on hydrophobic Si3N4 support for efficient degradation of organics diluted in water

TiO₂ photocatalyst loaded on Si₃N₄ (TiO₂/Si₃N₄) was prepared by a conventional impregnation method and its photocatalytic performance for the degradation of organics (2-propanol) diluted in water was compared with that of TiO₂ photocatalysts (TiO₂/SiO₂, TiO₂/Al₂O₃, and TiO₂/SiC) loaded on various types of supports (SiO₂, Al₂O₃, and SiC). The formation of the well-crystallized anatase phase of TiO₂ was observed on the calcined TiO₂/Si₃N₄ photocatalyst, while a small anatase phase of TiO₂ was observed on the TiO₂/SiC photocatalyst and amorphous TiO₂ species was the main component on the TiO₂/SiO₂ and TiO₂/Al₂O₃ photocatalysts. The measurements of the water adsorption ability of photocatalysts indicated that the TiO₂/Si₃N₄ photocatalyst exhibited more hydrophobic surface properties in comparison to other support photocatalysts. Under UV-light irradiation, the TiO₂/Si₃N₄ photocatalyst decomposed 2-propanol diluted in water into acetone, CO₂, and H₂O, and finally, acetone was also decomposed into CO₂ and H₂O. The TiO₂/Si₃N₄ photocatalyst showed higher photocatalytic activity than TiO₂ photocatalyst loaded on other supports. The well-crystallized TiO₂ phase deposited on Si₃N₄ and the hydrophobic surface of Si₃N₄ support are important factors for the enhancement of photocatalytic activity for the degradation of organic compounds in liquid-phase reactions.     

Enhanced visible light-induced photoelectrocatalytic degradation of phenol by carbon nanotube-doped TiO2 electrodes

We used a modified sol-gel method to prepare titanium dioxide and multi-walled carbon nanotube (CNT) composites that we subsequently deposited onto indium tin oxide (ITO) conductive glass plates. We characterized these CNT-doped TiO₂ (CNT-TiO₂) films using X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and diffuse reflectance UV-vis spectroscopy. The photoelectrocatalytic (PEC) activity of the composites was evaluated through their ability to mediate the degradation of phenol. XRD measurements indicated that the TiO₂ component existed solely in the anatase phase and that the crystallinity of the CNTs was low. XPS indicated that carbon atoms could substitute for both oxygen and titanium atoms in the TiO₂ lattice to form Ti-C and Ti-O-C structures, which were responsible for the extra photoabsorption and PEC activity under illumination with visible light, in addition to those provided by the CNTs and carbonaceous and Ti³⁺ species. An interphase interaction between TiO₂ and the CNTs elevated the photoabsorbance of the composites in the visible light region. A sample of TiO₂ doped with 10% CNTs and calcined at 400 °C exhibited the highest photocurrent and PEC efficiency. We systematically investigated the effects of several parameters of the PEC process, including the applied potential and pH, on the phenol conversion.