Determination of performance and exhaust emissions properties of B75 in a CI engine application

In this study, performance and exhaust emissions of biodiesel in a compression ignition engine was experimentally investigated. Therefore, biodiesel has been made by transesterification from cotton seed oil and then it was mixed with diesel fuel by 25% volumetrically, called here as B75 fuel. B75 fuel was tested, as alternative fuel, in a single cylinder, four strokes, and air-cooled diesel engine. The effect of B75 and diesel fuels on the engine power, engine torque and break specific fuel consumption were clarified by the performance tests. The influences of B75 fuel on CO, HC, NOx, Smoke opacity, CO₂, and O₂ emissions were investigated by emission tests. The engine torque and power, for B75 fuel, were lower than that of diesel fuel in range of 2-3%. However, for the B75, specific fuel consumption was higher than that of diesel fuel by approximately 3%. CO₂, CO, HC, smoke opacity and NO_x emissions of B75 fuel were lower than that of diesel fuel. The experimental results showed that B75 fuel can be substituted for the diesel fuel without any modifications in diesel engines.     

Biodiesel production from waste cooking oil via alkali catalyst and its engine test

Waste cooking oils (WCO), which contain large amounts of free fatty acids produced in restaurants, are collected by the environmental protection agency in the main cities of China and should be disposed in a suitable way. Biodiesel production from WCO was studied in this paper through experimental investigation of reaction conditions such as methanol/oil molar ratio, alkaline catalyst amount, reaction time and reaction temperature which are deemed to have main impact on reaction conversion efficiency. Experiments have been performed to determine the optimum conditions for this transesterification process by orthogonal analysis of parameters in a four-factor and three-level test. The optimum experimental conditions, which were obtained from the orthogonal test, were methanol/oil molar ratio 9:1, with 1.0 wt.% sodium hydroxide, temperature of 50 °C and 90 min. Verified experiments showed methanol/oil molar ratio 6:1 was more suitable in the process, and under that condition WCO conversion efficiency led to 89.8% and the physical and chemical properties of biodiesel sample satisfied the requirement of relevant international standards. After the analysis main characteristics of biodiese sample, the impact of biodiesel/diesel blend fuels on an YC6M220G turbo-charge diesel engine exhaust emissions was evaluated compared with 0# diesel. The testing results show without any modification to diesel engine, under all conditions dynamical performance kept normal, and the B20, B50 blend fuels (include 20%, 50% crude biodiesel respectively) led to unsatisfactory emissions whilst the B′20 blend fuel (include 20% refined biodiesel) reduced significantly particles, HC and CO etc. emissions. For example CO, HC and particles were reduced by 18.6%, 26.7% and 20.58%, respectively.     

Biodiesel production from pomace oil and improvement of its properties with synthetic manganese additive

Renewable energy sources are attracting more attention due to lower cost and lower pollution relative to fossil fuels. The aim of this experimental work is the production of renewable and clean methyl ester from pomace oil as an alternative fuel. This oil was obtained from pomace which is the waste of olive oil plants. Optimum producing conditions were determined experimentally. The maximum yield was obtained at 30% of methanol/oil ratio, 60 °C temperature for 60 min with NaOH catalyst. The properties of the biodiesel thus obtained were compared with diesel fuel requirements. An organic based Manganese additive improved the biodiesel properties. Doping the fuel at a ratio of 12 μmol/l oil methyl ester led to a 20.37% decrease in viscosity, 7 °C fall in the flash point and reduced the pour point from 0 °C to −15 °C. This blend of pomace oil methyl ester-diesel fuel with manganese additive was tested in a direct injection diesel engine. The maximum effect of the new fuel blend and diesel fuel on engine performance was obtained at 1400 rpm.     

Fuel production from waste vehicle tires by catalytic pyrolysis and its application in a diesel engine

An alternative fuel production was performed by pyrolysis of waste vehicle tires under nitrogen (N₂) environment and with calcium hydroxide (Ca(OH)₂) as catalyst. The sulfur content of liquids obtained were reduced by using Ca(OH)₂. The liquid fuel of waste vehicle tires(TF) was then used in a diesel engine to blend with petroleum diesel fuel by 5%(TF5), 10%(TF10), 15%(TF15), 25%(TF25), 35%(TF35), 50%(TF50), and 75%(TF75) wt. and pure (TF100). Performance characteristics such as engine power, engine torque, brake specific fuel consumption (bsfc) and exhaust temperature and emission parameters such as oxides of nitrogen (NOx), carbon monoxides (CO), total unburned hydrocarbon (HC), sulfur dioxides (SO₂) and smoke opacity of the engine operation with TF and blend fuels of TF-diesel were experimentally investigated and compared with those of petroleum diesel fuel. It was concluded that the blends of pyrolysis oil of waste tires TF5, TF10, TF25 and TF35 can efficiently be used in diesel engines without any engine modifications. However, the blends of TF50, TF75 and TF100 resulted considerably to high CO, HC, SO₂ and smoke emissions.     

Optimization of soy-biodiesel combustion in a modern diesel engine

As global petroleum demand continues to increase, alternative fuel vehicles are becoming the focus of increasing attention. Biodiesel has emerged as an attractive alternative fuel option due to its domestic availability from renewable sources, its relative physical and chemical similarities to conventional diesel fuel, and its miscibility with conventional diesel. Biodiesel combustion in modern diesel engines does, however, generally result in higher fuel consumption and nitrogen oxide (NO_x) emissions compared to diesel combustion due to fuel property differences including calorific value and oxygen content. The purpose of this study is to determine the optimal engine decision-making for 100% soy-based biodiesel to accommodate fuel property differences via modulation of air-fuel ratio (AFR), exhaust gas recirculation (EGR) fraction, fuel rail pressure, and start of main fuel injection pulse at over 150 different random combinations, each at four very different operating locations. Applying the nominal diesel settings to biodiesel combustion resulted in increases in NO_x at three of the four locations (up to 44%) and fuel consumption (11-20%) over the nominal diesel levels accompanied by substantial reductions in particulate matter (over 80%). The biodiesel optimal settings were defined as the parameter settings that produced comparable or lower NO_x, particulate matter (PM), and peak rate of change of in-cylinder pressure (peak dP/dt, a metric for noise) with respect to nominal diesel levels, while minimizing brake specific fuel consumption (BSFC). At most of the operating locations, the optimal engine decision-making was clearly shifted to lower AFRs and higher EGR fractions in order to reduce the observed increases in NO_x at the nominal settings, and to more advanced timings in order to mitigate the observed increases in fuel consumption at the nominal settings. These optimal parameter combinations for biodiesel were able to reduce NO_x and noise levels below nominal diesel levels while largely maintaining the substantial PM reductions. These parameter combinations, however, had little (maximum 4% reduction) or no net impact on reducing the biodiesel fuel consumption penalty.     

Performance and emission study of waste anchovy fish biodiesel in a diesel engine

Waste anchovy fish oils transesterification was studied with the purpose of achieving the conditions for biodiesel usage in a single cylinder, direct injection compression ignition. With this purpose, the pure biodiesel produced from anchovy fish oil, biodiesel-diesel fuel blends of 25%:75% biodiesel-diesel (B25), 50%:50% biodiesel-diesel (B50), 75%:25% biodiesel-diesel (B75) and petroleum diesel fuels were used in the engine to specify how the engine performance and exhaust emission parameters changed. The fuel properties of test fuels were analyzed. Tests were performed at full load engine operation with variable speeds of 1000, 1500, 2000 and 2500 rpm engine speeds. As results of investigations on comparison of fuels with each other, there has been a decrease with 4.14% in fish oil methyl ester (FOME) and its blends' engine torque, averagely 5.16% reduction in engine power, while 4.96% increase in specific fuel consumption have been observed. On one hand there has been average reduction as 4.576%, 21.3%, 33.42% in CO₂, CO, HC, respectively; on the other hand, there has been increase as 9.63%, 29.37% and 7.54% in O₂, NO_x and exhaust gas temperature has been observed. It was also found that biodiesel from anchovy fish oil contains 37.93 wt.% saturated fatty acids which helps to improve cetane number and lower NO_x emissions. Besides, for biodiesel and its blends, average smoke opacity was reduces about 16% in comparison to D2. It can be concluded that waste anchovy fish obtained from biodiesel can be used as a substitute for petroleum diesel in diesel engines.     

Potential for reducing emissions in a diesel engine by fuelling with conventional biodiesel and Fischer-Tropsch diesel

A gas-to-liquid (GTL) fuel derived from Low Temperature Fischer-Tropsch process has been tested in an automotive diesel engine fulfilling Euro 4 emissions regulations. Both regulated and non-regulated emissions have been compared with those of a commercial diesel fuel, a commercial biodiesel fuel and a GTL-biodiesel fuel (30% and 70% v/v, respectively) in order to check blending properties, synergistic effects and compatibility between first and second generation production technologies for biofuel consumption in current diesel engines. After presenting a detailed literature review, and confirming that similar efficiencies are attained with the four tested fuels under identical road-like operating conditions (this meaning fuel consumption is inversely proportional to their heating values), significant reductions in smoke opacity, particulate matter emissions and particle number concentration were observed with both GTL and biodiesel fuels, with small changes in NO_x emissions. Compared with the reductions in PM emissions derived from the use of biodiesel fuels, those derived from using GTL fuels were quite similar, despite its lower soot emissions reductions. This can be explained by the lower volatile organic fraction of the PM in the case of GTL. By adequately blending both fuels, a considerable potential to optimise the engine emissions trade-off is foreseen.     

The formation of deposits from oil under conditions pertinent to diesel engine pistons

The production of deposits from oil on various materials has been studied under conditions pertinent to the ring zone of a diesel engine piston. Deposition is found to occur only as a result of oxidation, and metal catalysed free radical reactions in the liquid phase appear to be responsible for the problem. Metal species removed from the surface are the most active promoters and these may be deactivated by heavy deposition (encapsulation) or by the addition of deactivating complexing agents.     

The influence of operating parameters on the performance and emissions of a DI diesel engine using methanol-blended-diesel fuel

In this study, the effects of injection pressure and timing on the performance and emission characteristics of a DI diesel engine using methanol (5%, 10% and 15%) blended-diesel fuel were investigated. The tests were conducted on three different injection pressures (180, 200 and 220 bar) and timings (15°, 20°, and 25° CA BTDC) at 20 Nm engine load and 2200 rpm. The results indicated that brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and nitrogen oxides (NO_x) emissions increased as brake thermal efficiency (BTE), smoke opacity, carbon monoxide (CO) and total unburned hydrocarbon (THC) decreased with increasing amount of methanol in the fuel mixture. The best results were achieved for BSFC, BSEC and BTE at the original injection pressure and timing. For the all test fuels, the increasing injection pressure and timing caused to decrease in the smoke opacity, CO, THC emissions while NO_x emissions increase.     

Effects of biodiesel on a DI diesel engine performance, emission and combustion characteristics

Experimental tests were investigated to evaluate the performance, emission and combustion of a diesel engine using neat rapeseed oil and its blends of 5%, 20% and 70%, and standard diesel fuel separately. The results indicate that the use of biodiesel produces lower smoke opacity (up to 60%), and higher brake specific fuel consumption (BSFC) (up to 11%) compared to diesel fuel. The measured CO emissions of B5 and B100 fuels were found to be 9% and 32% lower than that of the diesel fuel, respectively. The BSFC of biodiesel at the maximum torque and rated power conditions were found to be 8.5% and 8% higher than that of the diesel fuel, respectively. From the combustion analysis, it was found that ignition delay was shorter for neat rapeseed oil and its blends tested compared to that of standard diesel. The combustion characteristics of rapeseed oil and its diesel blends closely followed those of standard diesel.     

Characteristics of polycyclic aromatic hydrocarbons emissions of diesel engine fueled with biodiesel and diesel

With mutagenic and carcinogenic potential, polycyclic aromatic hydrocarbons (PAHs) from mobile source exhaust have contributed to a substantial share of air toxics. In order to characterize the PAHs emissions of diesel engine fueled with diesel, biodiesel (B100) and its blend (B20), an experimental study has been carried out on a direct-injection turbocharged diesel engine. The particle-phase and gas-phase PAHs in engine exhaust were collected by fiberglass filters and “PUF/XAD-2/PUF” cartridges, respectively, then the PAHs were determined by a gas chromatograph/mass spectrometer (GC/MS). The experimental results indicated that comparing with diesel, using B100 and B20 can greatly reduce the total PAHs emissions of diesel engine by 19.4% and 13.1%, respectively. The Benzo[a]Pyrene (BaP) equivalent of PAHs emissions were also decreased by 15.0% with the use of B100. For the three fuels, the gas-phase PAHs emissions were higher than particle-phase PAHs emissions and the most abundant PAH compounds from engine exhaust were naphthalene and phenanthrene. The analysis showed that there was a close correlation between total PAHs emissions and particulate matter (PM) emissions for three fuels. Furthermore, the correlation became more significant when using biodiesel.     

Dynamometer evaluation and engine wear characteristics of palm oil diesel emulsions

Dynamometer engine tests at steady-state conditions and a wear characteristics study were carried out on an indirect-injection diesel engine with palm oil diesel (POD) and its emulsions. The POD fuel was obtained in commercial form, and its emulsions were created by mixing POD fuel to contain 5 and 10% of water by volume. Variations in the engine’s performance characteristics were determined from the results of steady-state tests carried out at fifteen selected torque-speed matrix points of the engine’s performance map. The wear characteristics tests were performed by running the engine at half throttle setting for twenty hours for each fuel system. Then a desk-top comparison study was performed between the base-line fuel system of ordinary diesel (OD), POD, and its emulsions. Promising results have been obtained. Neither the lower cetane number of POD fuel nor its emulsification with water presented obstacles to the operation of the diesel engine during a series of steady-state engine tests and the twenty-hour endurance tests. Engine performance and fuel consumption for POD and its emulsions are comparable with those of OD fuel. Accumulations of wear metal debris in crank-case oil samples were lower with POD and its emulsions than with baseline OD fuel.     

Comparative study of performance and emissions of a diesel engine using Chinese pistache and jatropha biodiesel

An experimental study of the performances and emissions of a diesel engine is carried out using two different biodiesels derived from Chinese pistache oil and jatropha oil compared with pure diesel. The results show that the diesel engine works well and the power outputs are stable running with the two selected biodiesels at different loads and speeds. The brake thermal efficiencies of the engine run by the biodiesels are comparable to that run by pure diesel, with some increases of fuel consumptions. It is found that the emissions are reduced to some extent when using the biodiesels. Carbon monoxide (CO) emissions are reduced when the engine run at engine high loads, so are the hydrocarbon (HC) emissions. Nitrogen oxides (NOx) emissions are also reduced at different engine loads. Smoke emissions from the engine fuelled by the biodiesels are lowered significantly than that fuelled by diesel. It is also found that the engine performance and emissions run by Chinese pistache are very similar to that run by jatropha biodiesel.     

Fuel consumption and emissions from a diesel power generator fuelled with castor oil and soybean biodiesel

This work investigates the impacts on fuel consumption and exhaust emissions of a diesel power generator operating with biodiesel. Fuel blends with 5%, 20%, 35%, 50%, and 85% of soybean biodiesel in diesel oil, and fuel blends containing 5%, 20%, and 35% of castor oil biodiesel in diesel oil were tested, varying engine load from 9.6 to 35.7 kW. Specific fuel consumption (SFC) and the exhaust concentrations of carbon dioxide (CO₂), carbon monoxide (CO), and hydrocarbons (HC) were evaluated. The engine was kept with its original settings for diesel oil operation. The results showed increased fuel consumption with higher biodiesel concentration in the fuel. Soybean biodiesel blends showed lower fuel consumption than castor biodiesel blends at a given concentration. At low and moderate loads, CO emission was increased by nearly 40% and over 80% when fuel blends containing 35% of castor oil biodiesel or soybean biodiesel were used, respectively, in comparison with diesel oil. With the load power of 9.6 kW, the use of fuel blends containing 20% of castor oil biodiesel or soybean biodiesel increased HC emissions by 16% and 18%, respectively, in comparison with diesel oil. Exhaust CO₂ concentration did not change significantly, showing differences lower than ±3% of the values recorded for diesel oil operation, irrespective of biodiesel type, concentration and the load applied. The results demonstrate that optimization of fuel injection system is required for proper engine operation with biodiesel.     

Biodiesel development from high acid value polanga seed oil and performance evaluation in a CI engine

Non-edible filtered high viscous (72 cSt at 40 °C) and high acid value (44 mg KOH/gm) polanga (Calophyllum inophyllum L.) oil based mono esters (biodiesel) produced by triple stage transesterification process and blended with high speed diesel (HSD) were tested for their use as a substitute fuel of diesel in a single cylinder diesel engine. HSD and polanga oil methyl ester (POME) fuel blends (20%, 40%, 60%, 80%, and 100%) were used for conducting the short-term engine performance tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over entire range of engine operation at varying conditions of speed and load. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) were calculated from the recorded data. The engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature and exhaust emissions (CO, CO₂, HC, NO_x, and O₂) were recorded. The optimum engine operating condition based on lower brake specific fuel consumption and higher brake thermal efficiency was observed at 100% load for neat biodiesel. From emission point of view the neat POME was found to be the best fuel as it showed lesser exhaust emission as compared to HSD.     

A rapid test to measure performance,emission and wear of a diesel engine fueled with palm oil diesel

Results of performance, emission and tribological evaluations of palm oil methyl ester and its blends with conventional diesel in an automobile diesel engine test bed are presented. Polymerization and carbon deposits on the fuel injector were monitored. CO, CO₂, O₂, combustion efficiency and temperature of exhaust gases were also measured. Palm oil methyl ester and its blends have great potential as alternative diesel fuel. Performance and exhaust gas emission for palm oil methyl ester and its blends with conventional diesel are comparable with those of conventional diesel fuel. Palm oil methyl ester does not pose a severe environmental problem and will not deteriorate engine and bearing components.     

Biodiesel influence on tribology characteristics of a diesel engine

This paper deals with the influence of biodiesel on some tribology characteristics of a bus diesel engine with a mechanically controlled fuel injection system. The tests have been performed on a fully equipped engine test bed, on a fuel injection test bed and on a discharge coefficient testing device. The tested fuel was neat biodiesel produced from rapeseed. Attention was focused on the biodiesel influence on the pump plunger surface roughness, on the carbon deposits in the combustion chamber, on the injector and in the injector nozzle hole. The pump plunger surface was analyzed by experimentally determined roughness parameters and by a microscope. The carbon deposits at fuel injector and in the combustion chamber were examined using endoscopic inspection. The deposits in the injector nozzle were investigated indirectly by measuring the nozzle discharge coefficient. Numerical simulation has been performed in order to estimate the influence of the discharge coefficient variation on the computed injection characteristics. The obtained results indicate that biodiesel usage may even improve the pump plunger lubrication conditions. Furthermore, the carbon deposits in the combustion chambers did not vary significantly in quantity but they were noticeably redistributed. Finally, it was found out that the variation of the nozzle discharge coefficient has to be taken into account only if high accuracy of numerical simulation is desired.     

Performance of a diesel generator fuelled with palm oil

Pure palm oil may be employed in diesel engines as an alternative fuel. Engine performance and emissions were influenced by basic differences between diesel fuel and palm oils such as mass based heating values, viscosity, density and molecular oxygen content. The high viscosity of palm oil resulted in poor atomisation, carbon deposits, clogging of fuel lines and starting difficulties in low temperatures. When heated at 100 °C palm oil presented lower viscosity, better combustion and less deposits. Tests were conducted in a naturally aspirated MWM 229 direct injection four-stroke 70 kW diesel-generator fueslled with 100% palm oil.     

Effect of biofuels combustion on the nanoparticle and emission characteristics of a common-rail DI diesel engine

This study was performed to investigate the effect of biogas-biodiesel fuel combustion on the emissions reduction and nanoparticle characteristics in a direct injection (DI) diesel engine. In order to apply the two biofuels, biogas was injected into a premixed chamber during the intake process by using two electronically controlled gas injectors, and biodiesel fuel was directly injected into combustion chamber by a high-pressure injection system. The in-cylinder pressure and rate of heat release (ROHR) were investigated under various fuel conditions for single-fuel (biodiesel) and dual-fuel (biogas-biodiesel) combustions. To evaluate the engine performances and exhaust emissions characteristics, the indicated mean effective pressure (IMEP) and exhaust emissions were also investigated under various test conditions. Furthermore, the particle number concentration and the size distribution of nanoparticles were analyzed by using a scanning mobility particle sizer (SMPS).In the case of dual-fuels, the peak combustion pressure and ROHR were gradually decreased with the increase of the biogas fraction in the dual-fuels. As the premixed ratios increased, ignition delay and combustion durations were prolonged compared to single-fuel mode. The dual-fuels combustion showed that the IMEP decreased slightly and maintained similar levels up to 20° BTDC due to the retarded combustion phase. The concentrations of NO_x emissions were decreased for all injection timings as the premixed ratio (r_p) increased. The soot emissions in dual-fuel operations were significantly lower than those in the single-fuel mode (r_p = 0), and decreased gradually as the premixed ratio increased, regardless of injection timing. A lower nanoparticle size distribution was observed at all premixed ratios for dual-fuel combustion compared to those of the single fuel mode. The number distribution of both nuclei and accumulation modes also decreased with an increase in the biogas fraction. A slight reduction in the total particle number and total volume for all premixed ratios was observed as the injection timing increased from TDC up to 20° BTDC.     

RFCC柴油非加氢精制技术及其应用

采用多种非加氢手段对RFCC柴油进行精制。在油品中加入少量酚类或胺类物质能终止自 由基链反应;某些活性固体物质对碱性氮有良好的吸附能力;在极性环境中能进一步萃取含氮、硫杂质。 四种复合非加氢技术精制的柴油指标达GB252-2000标准要求。