Room temperature synthesis and characterization of polythiophene thin films by chemical bath deposition (CBD) method

Polythiophene thin films were deposited successfully on glass substrate by chemical bath deposition method using FeCl₃ as an oxidant and chloroform as solvent. The effect of oxidant concentration on the properties of polythiophene thin films was studied. The surface morphology was influenced by oxidant concentration and deposition time. The oxidation concentration also strongly affects the optical properties of the polythiophene thin films. The transmittance decreases while the absorption, band gap and refractive index increases due to increase in oxidant concentration.     

Direct reconstruction of complex refractive index distribution from boundary measurement of intensity and normal derivative of intensity

We present an optical tomographic reconstruction method to recover the complex refractive index distribution from boundary measurements based on intensity, which are the logarithm of intensity and normal derivative of intensity. The method, which is iterative, repeatedly implements the forward propagation equation for light amplitude, the Helmholtz equation, and computes appropriate sensitivity matrices for these measurements. The sensitivity matrices are computed by solving the forward propagation equation for light and its adjoint. The results of numerical experiments show that the data types ln(I) and partial differential I/ partial differential n reconstructed, respectively, the imaginary and the real part of the object refractive index distribution. Moreover, the imaginary part of the refractive index reconstructed from partial differential I/ partial differential n and the real part from ln(I) failed to show the object's inhomogeneity. The value of the propagation constant, k, used in our simulations was 50, and this value resulted in smoothing of the reconstructed inhomogeneities. Thus we have shown that it is possible to reconstruct the complex refractive index distribution directly from the measured intensity without having to first find the light amplitude, as is done in most of the currently available reconstruction algorithms of diffraction tomography.     

Near-field optical recording with nanocomposite cover-layer for numerical aperture of 1.85

Near-field optical recording media with a nanocomposite cover-layer were prepared and tested using a gap servo, near-field recording system with an effective numerical aperture of 1.85. The refractive index of the nanocomposite cover-layer, which has a smooth surface, is 1.86, yielding a successful gap servo operation. However, the recording density cannot be maximized due to the refractive index of the cover-layer being lower than the required value for the effective numerical aperture. A recording density of 95?GB per disc can be achieved with a nanocomposite cover-layer having a refractive index of 1.86. The readout signal from 110?GB is not clear due to the reduced eventual numerical aperture in conjunction with the limited refractive index of the cover-layer.     

Multispeed rewritable optical-recording method with an initialization-free phase-change disk

A new method of multispeed rewritable optical recording is presented. An initialization-free phase-change optical disk is proposed as a candidate for multispeed rewritable optical recording. The simulated results of the initialization-free disk at different linear velocities show that the cooling rate increases from approximately 18.69% to 37.96%. A model that combines the crystallization acceleration effect due to the additional layers and the rapid cooling rate due to the initialization-free disk structure is proposed as the physical mechanism of the multispeed recording method with an initialization-free disk. The dynamic optical-recording properties of the initialization-free DVD-RAM disk at different recording speeds shows that the initialization-free phase-change optical-recording disk is compatible with a broad range of recording speeds from 3.49 to 12.21 m/s.     

一种基于聚乙烯醇/丙烯酸-2-羟基乙酯的新型全息存储材料

本文研究了一种基于聚乙烯醇/丙烯酸-2-羟基乙酯的新型全息存储材料;研究了不同浓度的丙烯酸-2-羟基乙酯对光聚物材料衍射效率的影响;在厚度为95μm的光聚物薄膜中当曝光能量为231mJ/cm2时获得了近75%的高衍射效率。应用Matlab软件以光化学漂白理论、角度响应曲线理论为拟合模型,进行了基于Levenberg-Marquardt算法的非线性曲线拟合;通过非线性曲线拟合研究了不同浓度的丙烯酸-2-羟基乙酯对摩尔吸收系数、量子产率、折射率调制度、光聚物薄膜厚度等多个全息参数的影响;实验表明,丙烯酸-2-羟基乙酯的加入可有效增加光聚物薄膜的厚度并且改善光聚物薄膜的结构和性能,达到提升聚乙烯醇/丙烯酰胺光聚物初始材料的全息特性,改进光聚物材料全息光学数据存储容量的目地。     

Double slit interferometry to measure the EUV refractive indices of solids using high harmonics

Accurate values of the extreme ultraviolet (EUV) optical properties of materials are required to make EUV optics such as filters and multilayer mirrors. The optical properties of aluminum studied in this report are required, in particular, as aluminum is used as an EUV filter material. The complex refractive index of solid aluminum and the imaginary part of the refractive index of solid iron between 17 eV and 39 eV have been measured using EUV harmonics produced from an 800 nm laser focused to 10(14) Wcm(2) in an argon gas jet impinging on a double slit interferometer.     

Performance of a write-once multilayer optical disk that uses transparent recording material with an optical switching layer

A volumetric optical disk that has multiple transparent films with optical switching layers is used as a recording medium to increase the number of recording layers. In the disk the optical switching layer is adapted to reduce decay of laser energy and increase reading and recording sensitivity. Well-defined marks of approximately 100-nm depth can be placed precisely on the transparent films by a focused laser beam. Writing and reading of a four-layer recordable disk, fabricated by molding and spin bonding, have been demonstrated experimentally. The volumetric disk can achieve a high recording capacity with conventional optical pickups.     

Effects of refractive-index mismatch on three-dimensional optical data-storage density in a two-photon bleaching polymer

Reported is an investigation into the effect of spherical aberration caused by the mismatch of the refractive indices between the recording material and its immersion medium on the three-dimensional optical data-storage density in a two-photon bleaching polymer. It is found both theoretically and experimentally that spherical aberration can be compensated for by a change in the tube length at which a microscope objective is operated in recording and reading processes. After compensation for the spherical aberration it is possible to achieve a three-dimensional recording density of 3.5 Tbits/cm(3) for a commercial objective with a numerical aperture of 1.4.     

可擦重写光盘记录介质材料及其特性

可擦重写光盘因其能对已写入文件进行改写,因此比只读光盘、一次写入光盘具有更大的灵活性,从而具有很好的应用前景。论述了两种可擦重写光盘记录介质即磁光盘记录介质与相变光盘记录介质的记录机理,并详细阐述了两种记录介质的性能要求。     

Analysis and simulations of two-wave mixing in photopolymer holographic recording media

Abstract

The process of two-wave mixing in photopolymer recording materials was investigated theoretically. The diffraction grating already forms during exposition and it may influence the original interference field distribution through diffraction of waves on the refractive index modulation. In order to show this, Kogelnik's coupled wave theory was extended to demonstrate the possibility of energy transfer from one recording wave to the other. The energy transfer and the intensity distribution during the recording process were systematically analysed depending on the boundary conditions. As a next step, the first harmonic model of the transmission grating recording, based on a simple material model, was implemented and solved. The ratio of the input intensities was found to be a crucial parameter and thus extensive simulations for various ratios of intensities were carried out. Modelling implies that the interference field and the refractive index grating just coincide for equal intensities. For intensities differing from unity they do not overlap themselves during the recording process. It has also turned out that the diffraction efficiency of the recorded grating drops against the case where the effects of two-wave mixing are not considered. The results of our analysis and simulation help give a better understanding of the physics of the recording process and proper adjustment of recording parameters in such applications as optical holography and holographic memories.     

Use of analyte-modulated modal power distribution in multimode optical fibers for simultaneous single-wavelength evanescent-wave refractometry and spectrometry

A new method is described for the simultaneous determination of absorbance and refractive index of a sample medium. The method is based on measurement of the analyte-modulated modal power distribution (MPD) in a multimode waveguide. In turn, the MPD is quantified by the far-field spatial pattern and intensity of light, i.e., the Fraunhofer diffraction pattern (registered on a CCD camera), that emerges from a multimode optical fiber. Operationally, light that is sent down the fiber interacts with the surrounding analyte-containing medium by means of the evanescent wave at the fiber boundary. The light flux in the propagating beam and the internal reflection angles within the fiber are both affected by optical absorption connected with the analyte and by the refractive index of the analyte-containing medium. In turn, these angles are reflected in the angular divergence of the beam as it leaves the fiber. As a result, the Fraunhofer diffraction pattern of that beam yields two parameters that can, together, be used to deduce refractive index and absorbance. This MPD based detection offers important advantages over traditional evanescent-wave detection strategies which rely on recording only the total transmitted optical power or its lost fraction. First, simultaneous determination of sample refractive index and absorbance is possible at a single probe wavelength. Second, the sensitivity of refractometric and absorption measurements can be controlled simply, either by adjusting the distance between the end face of the fiber and the CCD detector or by monitoring selected modal groups at the fiber output. As a demonstration of these capabilities, several weakly absorbing solutions were examined, with refractive indices in the range from 1.3330 to 1.4553 and with absorption coefficients in the range 0-16 cm-1. The new detection strategy is likely to be important in applications in which sample coloration varies and when it is necessary to compensate for variations in the refractive index of a sample.     

Effect of zeolite nanoparticles on the optical properties of diacetone acrylamide-based photopolymer

The effect of zeolite nanoparticles with BEA type framework structure on the optical properties of a diacetone acrylamide (DA)-based holographic photopolymer has been investigated. Both types of zeolite nanocrystals, as synthesized (BEA) and silver containing (BEA-Ag), are used for doping the DA photopolymer. Doping of the DA photopolymer with BEA zeolites results in an 11% decrease of the average refractive index of the nanocomposite layer, while the inclusion of BEA-Ag nanoparticles decreases the average refractive index by 3% only. This observation is in good agreement with the fact that the contrast in refractive index between the host photopolymer and nanoparticles is expected to be much lower for the BEA nanoparticles containing Ag in their pores. Doping of the DA photopolymer with pure BEA zeolite nanoparticles results in a significant increase in refractive index modulation due to holographic recording, Δn, of up to 91% at a concentration of 2 wt.% compared to un-doped layers. For the BEA-Ag zeolites, a maximum increase in Δn of up to 17% at a concentration of 0.5 wt.% is observed. The increase in Δn is attributed to the difference in n between the host photopolymer and nanoparticles and the redistribution of the nanoparticles during holographic recording. It is demonstrated that the DA photopolymer is compatible as a host material for the porous BEA nanoparticles. This is due to the large size of the DA monomer molecules, which restricts monomer migration into the zeolite pores and thus the pores of the Ag-free BEA nanoparticles remain empty, making them suitable for application in holographic sensors.     

Optimisation of distributed feedback laser biosensors

A new integrated optical sensor chip is proposed, based on a modified distributed- feedback (DFB) semiconductor laser. The semiconductor layers of different refractive indices that comprise a laser form the basis of a waveguide sensor, where changes in the refractive index of material at the surface are sensed via changes in the evanescent field of the lasing mode. In DFB lasers, laser oscillation occurs at the Bragg wavelength. Since this is sensitive to the effective refractive index of the optical mode, the emission wavelength is sensitive to the index of a sample on the waveguide surface. Hence, lasers are modelled as planar waveguides and the effective index of the fundamental transverse electric mode is calculated as a function of index and thickness of a thin surface layer using the beam propagation method. We find that an optimised structure has a thin upper cladding layer of ~0.15 mum, which according to this model gives detection limits on test layer index and thickness resolution of 0.1 and 1.57 nm, respectively, a figure which may be further improved using two lasers in an interferometer-type configuration.     

PbSe量子点掺杂玻璃折射率的实验测量

为了明确PbSe量子点掺杂硅酸盐玻璃的光学特性,利用阿贝折射仪和带激光光源的分光计测量了其折射率,多次重复测量表明,该组分的量子点掺杂玻璃具有较稳定的折射率（nD=1．5981±0．0027）,是非常理想的光纤制备材料。实验还表明,阿贝折射仪可以用来快速准确地测量某些固体材料的折射率,为研究新材料的折射率特性提供了一种快速测量方法。     

Angstrom-range optical path-length measurement with a high-speed scanning heterodyne optical interferometer

A highly accurate method of optical path-length measurement is introduced by use of a scanning heterodyne optical interferometer with no moving parts. The instrument has demonstrated the potential to measure optical path length at angstrom resolution over continuous thickness in the micrometer range. This optical path length can be used to calculate the thickness of any material if the refractive index is known or to measure the refractive index of the material if the thickness is known. The instrument uses a single acousto-optic device in an in-line ultra-stable reflective geometry to implement rapid scanning in the microsecond domain for thickness measurements of the test medium.     

Effect of zinc content on the refractive index of Co-sputtered Zn-doped ITO films

In this study, we investigated the possibility of using Zn-doped ITO film as an alternative material for conventional SiO2 waveguides used in optical communication. The Zn-doped ITO films were deposited on quartz substrates using a combinatorial sputtering system, which yielded composition spread Zn-In-Sn-O (ZITO) films by co-sputtering two targets of ITO and ZnO. The Zn-doped ITO films deposited at room temperature exhibited an amorphous phase in the Zn content [Zn/(Zn+In+Sn)] range of 39-54 at%. The Zn-doped ITO films deposited at low oxygen partial pressure showed resistivity below 10(-3) ohms cm and optical transmittance of approximately 85% at 550 nm. The refractive index calculated by the Swanepoel method was found to be dependent on the Zn content in the Zn-doped ITO films. The calculated bending loss from the refractive index indicated that Zn-doped ITO could be utilized as a new waveguide material for various optical devices, such as optical splitters, wavelength division multiplexers (WDMs), optical modulators, and optical switches.     

Photo-thermo-refractive glass co-doped with Nd as a new laser medium

Photo-thermo-refractive (PTR) glass demonstrates refractive index change after exposure to UV radiation followed by a thermal treatment that enables recording of high efficiency holographic optical elements. This work demonstrates feasibility of function of this material as a complex optical medium which posseses both photosensitive and luminescent properties and paves a way for creation of monolythic solid state lasers where resonator components can be holographically recorded inside of a laser medium. It was found, that incorporating of Nd³⁺ ions in PTR glass does not affect photosensitivity required for hologram recording. It was demonstrated that emission wavelength, spectral width, and cross section of Nd³⁺ luminescence in PTR glass are typical for silicate laser glasses and Nd-doped PTR glass can be considered as a promising laser medium for monolithic solid state lasers.     

Metallized thiazolylazo dyes as optical recording materials

A series of metallized thiazolylazo dyes have been designed and synthesized. Smooth films on optical glass and single-crystal silicon were prepared using the spin-coated method. The UV-Vis absorption spectra of the dyes were measured in solution and in films. The optical constant (complex refractive index N=n+ik) of the films on single-crystal silicon has been determined using a scanning ellipsometer. The variation of the complex refractive index, N, with wavelength, λ, was obtained. From the value of n, k and the thickness of the dye films, the variation of the reflectance vs dye film thickness was then calculated. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) of the nickel thiazolylazo dye showed a clear threshold of thermal decomposition with a sharp exothermic park. Static optical recording tests were carried out. The results show that the nickel thiazolylazo dye is more suitable for use in short-wavelength diode-laser optical recording.     

用于环氧树脂固化监测的自参考型光纤固化传感器

研究了一种新型的自参考型光纤固化传感器,用于环氧树脂固化过程的实时监测。用光纤芯折射率为1.558的多模光纤制成端面反射型折射率传感器,利用环氧树脂的折射率与固化度之间的对应关系,通过实时测量环氧树脂的折射率进行固化监测。在固化过程中,当环氧树脂的折射率变化到与光纤芯的折射率相等时,传感界面的反射信号为零,传感器可对零点偏置和灵敏系数进行校准,在此后的固化过程中,传感器能够定量地测量环氧树脂的固化度。在用多个传感器对树脂内不同部位的固化过程同时进行监测的场合,各传感器经实时自参考校准后,可根据各自的灵敏系数对输出信号统一定标,从而可以相互比较,实时地反映不同部位的固化反应过程之间的差异。