共查询到20条相似文献,搜索用时 93 毫秒
1.
2.
王媛敬 《天津光电线缆技术》2009,(1):6-8
1问题的由来
2007年10月,我公司提供南京某研究所用于某大型装备的高温电缆,在使用过程中出现护套收缩和绝缘熔化现象。我公司予以高度重视,立即派出技术人员赶赴用户驻地,实地了解该电缆的使用条件,考察该电缆的应用状况。在该电缆的使用现场我们看到,该电缆在使用前需要进行剥头处理,而剥头所用的工具具有加热吹风功能。为提高剥头速度,每次剥头时, 相似文献
3.
DC/DC产品批量生产过程中,由于工艺过程控制措施不到位,容易造成产品绝缘性能的下降,本文通过对绝缘失效的原因进行统计和分析,就其解决措施做了简单的阐述。 相似文献
4.
本文从绝缘电阻理论出发,分析了与绝缘电阻性能相关核心因素,结合通信电缆产品生产特点,提出产品设计、生产制造控制过程中的注意事项,提高了通信电缆绝缘电阻性能,并通过正确的评价,为提供优质可靠的通信电缆服务。 相似文献
5.
叙述了将国家863计划项目成果高辐射高绝缘釉质膜烧结到红外辐射陶瓷片表面后,不仅提高了辐射性能和绝缘性能,而且提高了机械强度,延长了使用寿命。 相似文献
6.
分析了高温和高湿的气候条件对电子产品安全性能的影响,并以模拟试验进行验证。通过在不同环境温度下进行发热试验和经潮湿处理后测量绝缘漏电流,对得到的数据进行分析,以验证高温高湿条件对产品绝缘性能的影响。 相似文献
7.
8.
9.
10.
11.
为了实现测量中性点不接地配电系统(IT系统)母线绝缘参数的目的,通过向系统加载脉冲信号,然后测量系统响应信号的电压值,进而计算得到系统母线的分布电容和绝缘电阻值,利用测量值监测系统的绝缘状况。通过对大量仿真数据的分析可知,该方法具有较高的绝缘监测效率。 相似文献
12.
A method for estimating the conductance of each insulation layer of MNOS devices is described. In this method, the conductance values can be independently estimated using the frequency dependence of the capacitance and conductance versus gate voltage characteristics. The frequency dependence in the accumulation region can be explained by an equivalent circuit which considers the substrate resistance and the conductance of each insulation layer. It was found that the conduction processes in nitride and oxide layers are dominated by Frenkel-Poole emission and direct tunnelling emission, respectively, and that the degradation of retention characteristics of MNOS memory devices with erase/write cycles is caused by increased nitride conductance 相似文献
13.
针对电容发展所面临的电容密度、绝缘强度和高频特性等方面问题,利用兼具横向、纵向电通量的叉指电极结构提出一种新型三维电容。电容测试及分析结果表明采用该设计结构能将电容最高击穿电压增大到40V,最高工作频率提升到10 GHz以上,电容值可调范围比平面电容扩大了2~3倍,有助于解决电容发展中面临的相关问题。 相似文献
14.
邱小波 《光纤与电缆及其应用技术》2010,(5):23-24,31
介绍了电压驻波比(VSWR)的计算方法。选取了电缆组件装配过程中影响电压驻波比的三大主要因素:内导体剥线尺寸、绝缘子剥线尺寸、内导体焊锡量,进行了正交试验,通过对试验结果的分析,得到实现较好电压驻波比性能所需的最佳电缆组件的生产条件。 相似文献
15.
Stray capacitance modeling of an inductor is essential for its RF equivalent circuit modeling and inductor design. Stray capacitance determines an inductor's performance and upper frequency limit. A method has been proposed for modeling the distributed stray capacitance of inductors by the finite element method and a node-to-node lumped capacitance network. The effects of wire insulation layer, ferrite core, number of segments used to model the circumference of a wire cross section, pitch and coil-to-core distances, and the capacitance between nonadjacent turns, etc., an an inductors' self-capacitance and calculation accuracy, have all been considered. The calculated equivalent lumped stray capacitance for a rod inductor with a ferrite core is compared to that estimated from measurement. Good agreement between them has been observed 相似文献
16.
17.
采用四层端电极(Ni/Cu/Ni/Sn)结构设计,底层为Ni,电镀Cu/Ni/Sn的工艺方法,制作了大容量MLCC。研究了四层结构和三层结构(Cu/Ni/Sn)对电容量等基本电性能、可靠性和内应力的影响。结果表明:制作1206规格10μFMLCC,C为9.86~10.46μF、tanδ为(360~390)×10–4、绝缘电阻≥1.5×108Ω、耐电压值为175~205V,四层结构与三层结构电性能相当。可靠性测试中,四层结构抗机械和热冲击能力提高了20%,且有利于瓷体内应力释放。 相似文献
18.
19.
20.
柠檬酸盐对阳极箔形成速度与比电容的影响 总被引:2,自引:0,他引:2
为了提高铝电解电容器用高压阳极箔形成速度与比电容,将水合处理后的腐蚀箔在95℃、2 g/L柠檬酸钠去离子水溶液中浸泡5 min,在530 V电压化成时,形成时间缩短约2 min,化成箔比电容由0.556×10–6 F.cm–2提高至0.584×10–6 F.cm–2,阳极氧化铝膜的结构与性能得到改善。 相似文献