热泵吸附器中传热传质过程的研究

对吸附式热泵循环系统中的传热传质进行了理论分析和实验研究,建立了吸附器中热传导方程.计算求解值与实验结果相一致,说明了吸附器中的传热速率控制了热泵循环速度.据此,对吸附器中强化传热肋片进行了模拟分析,作为吸附器优化设计的理论依据.     

竖直管外降膜吸收传热传质过程强化的研究

对LiBr溶液在光滑管和四种换热强化管竖直管外降膜吸收过程进行了实验研究，得到了实验条件下的最佳管型，分析了非绝热吸收过程中传热传质相互作用，相互影响的关系，建立了竖直管外降膜吸收热－质传递过程的数学模型，并对该过程进行了数值计算，模型计算值与实验结果的比较证明该模型具有较好的适用性。     

流化连续造粒过程传热传质分析

根据连续造粒机造粒室内的温度分布状况 ,将流化连续造粒过程沿高度方向分成四个区域 ,并对各区域粉粒的传热传质进行了分析 ,得出了适合于连续造粒机的传热计算式 ,这对该类机型的研制开发具有一定的指导意义。     

物料干燥过程—传质传热最优化方法的研究

论述了多孔介质干燥过程中传质传热的数学模型及干燥过程最优化准则的建立；并且动用控制理论产物料干燥过程传热的动态优化方法－－准则约束法，且得到了最优解。     

结晶垢结垢过程的传热传质模型

通过对结晶垢结垢过程传热传质机理的分析,证明了垢层表面温度随时间的变化会对结垢过程产生重大影响.据此提出了考虑垢层表面温度变化的描述结垢过程的传热传质模型.对恒壁温和恒热流条件下的结垢过程进行了详尽的分析和讨论.结果表明,对恒壁温情况必须考虑垢层表面温度随时间的变化,这一变化是导致结垢过程渐近特性的重要原因之一;而对恒热流情况,垢层表面温度随时间的变化很小,可以忽略它所带来的对结垢过程的影响.与实验数据比较表明,模型预测是正确可靠的.     

减压膜蒸馏传热传质过程

对减压膜蒸馏传热传质机理进行了研究,在已有理论模型的基础上,考虑温度极化和浓差极化的影响,引入减压膜蒸馏传热传质理论模型,并对模型进行了计算,结果表明:随温度的升高,传质系数Km升高,温度极化系数TPC减小,浓差极化系数CPC增大,通量呈近指数倍增加;随流速的增加.TPC增大,膜表面传热系数hf增大,CPC略有降低,K...     

空调用金属填料表面传热传质过程的数值分析

建立了填料塔的二维传热传质模型,考虑了因水蒸发或凝结而引起的水的质量变化和空气的质量变化.利用实验数据回归得到的传热系数和传质系数.用差分法求得了更接近实际的数值解.实验研究证明使用这个改进的方法,使得模型的数值解与实验结果吻合得较好.数值分析结果描述了金属填料内部空气的湿球温度场和填料表面水膜的温度场,有助于研究金属填料表面传热传质性能,为金属填料用于空调机组中的设计提供了计算方法,可以给出满足工程精度要求的设计依据.     

流化床喷雾造粒过程的传热传质

This article presents a mathematical model of heat and mass transfer for the process of fluidized-bed spray granulation, which can be applied in the analysis of bed temperature profile, temperature and humidity of outlet gas and moisture content of particles. Effects of operation parameters on the batch granulation are investigated. The theoretical calculation agrees reasonably well with the experimental data.Keywords fluidized-bed spray granulation, mathematical model, heat and mass transfer     

非饱和含湿多孔介质微波冷冻干燥过程传热传质分析

基于升华冷凝模型,对非饱和含湿多孔介质微波冷冻干燥过程作了数值计算．结果表明,干燥过程中不饱和含冰区内的冰饱和度有较大变化．通过与不考虑升华冷凝区相比较,表明升华冷凝区的存在不可忽略．     

热泵干燥过程中相变传热与传质分析

根据孤立系统热力学耦合原理,分析热泵干燥过程中存在的气液相变过程,揭示了相变过程中传热过程与传质过程之间的相互作用机制.分析得到,提高蒸发器的蒸发温度、降低冷凝器工质的冷凝温度,可以减少系统的熵产率.通过介绍干燥过程中水分汽化相变和迁移扩散中流与力的关系,得到热流和质流的线性唯象方程组,结合散度概念推导质量守恒方程和能...     

Heat and Mass Transfer in Process of Fluidized-Bed Spray Granulation

This article presents a mathematical model of heat and mass transfer for the process of fluidized-bed spray granulation, which can be applied in the analysis of bed temperature profile, temperature and humidity of outlet gas and moisture content of particles. Effects of operation parameters on the batch granulation are investigated. The theoretical calculation agrees reasonably well with the experimental data.     

A Numerical and Experimental Study of Natural Convective Heat and Mass Transfer from a Vertical Porous Plate

ABSTRACT

A finite difference scheme for solving the problem of natural transport of heat, mass, momentum and species concentration along vertical porous plates is presented. Several drying related problems are numerically solved, by including a gas-injection boundary condition directly into the governing equations. The effect of variable physical properties is investigated by means of direct comparison against experimental data obtained through holographic interferometry. The relative importance of wall diffusive and convective fluxes is examined. Sherwood and Nusselt numbers can be accurately obtained by means of the proposed techniques.     

A Numerical and Experimental Study of Natural Convective Heat and Mass Transfer from a Vertical Porous Plate

A finite difference scheme for solving the problem of natural transport of heat, mass, momentum and species concentration along vertical porous plates is presented. Several drying related problems are numerically solved, by including a gas-injection boundary condition directly into the governing equations. The effect of variable physical properties is investigated by means of direct comparison against experimental data obtained through holographic interferometry. The relative importance of wall diffusive and convective fluxes is examined. Sherwood and Nusselt numbers can be accurately obtained by means of the proposed techniques.     

热管式降膜吸收器的传热传质

对热管式降膜吸收顺溶液吸收传热传质并通过热管移出吸收热的过程进行了数值研究，根据所建立的数学模型，通过求解热管加热段外壁面溶液波动降膜的动态二维偏微分方程和热管传热方程，研究了膜雷诺数，低位余热温度，输出温度等因素对传热管质过程的影响，对进一步工作提出了新的见解。     

湿空气掠过竖直平板层流强制对流凝结换热的传热传质研究(英文)

Condensation of humid air along a vertical plate was numerically investigated, with the mathematical model built on the full boundary layer equations and the film-wise condensation assumption. The velocity, heat and mass transfer characteristics at the gas-liquid interface were numerical analyzed and the results indicated that it was not reasonable to neglect the condensate film from the point of its thickness only. The condensate film thickness, interface temperature drop and the interface tangential veloc...     

Effect of Turbulence on Heat and Mass Transfer in the Atomization Zone

One of possibilities to extend operating efficiency of spray dryers is to increase turbulence of the drying agent flow. In the literature no quantitative data describing this phenomenon are available.

In the paper results of experimental investigations on the effect of turbulence on heat and mass transfer during atomization are discussed. The scope of experiments covered the analysis of changing evaporation capacity. temperature of gas and atomized material and particle size distribution as a function of distance to the atomizer. It was proven that an increase of air flow turbulence could cause 20-25% increase of evaporation capacity.     

滚筒干燥器内丝状物料的传热传质特性研究

干燥涉及众多生产领域,卷烟加工过程中存在干燥环节,滚筒烘丝机是用于干燥烟丝的主要设备。在滚筒烘丝机内,烟丝与周围环境进行热质交换,不同的运行控制条件,将直接影响烟丝的品质。由于干燥过程受众多因素的影响,至今烟草加工企业对烘丝机内部烟丝的传热传质特性缺乏深层次的认识,不利于烟丝品质的提高。针对上述背景,本文基于传热传质学、流体力学、多相流动等相关理论,通过计算机数值模拟方法,建立并求解滚筒内的传热传质数学模型,获得不同操作条件下烟丝温度、含水率变化的详细信息,并将所得结果与实际生产数据相验证。研究结果表明,烟丝与气流逆流流动条件下,干燥过程存在三个阶段：预热段、恒速段、降速段,烟丝含水率先升后降,烟丝温度经历先升高、后降低、再升高的过程;顺流流动条件下,干燥过程存在两个阶段：预热段与恒速段,烟丝含水率沿程单调下降,烟丝温度在预热段急剧上升,在恒速段平缓上升。     

高初始含湿多孔介质喷雾干燥过程的热质耦合传递

多孔介质是大量干燥过程的主体,由于实际多孔介质干燥过程的复杂性,建立通用的干燥过程传热传质模型十分困难。通过分析喷雾干燥过程中高初始含湿多孔介质与干燥介质之间的传热传质机理以及各因素对传热传质的影响,根据马歇尔方程探讨了干燥介质与料雾之间的水蒸汽分压差在干燥过程中的变化情况,反映了多孔湿介质在喷雾干燥操作中的传热传质过程的几种特性,为确定实际生产中喷雾干燥器的操作条件指明了新的出路。     

升温型吸收式热泵吸收器强化传热传质研究进展

文章综合介绍了国内外关于升温型吸收式热泵吸收器强化传热传质的研究进展。主要从添加表面活性剂,采用高效换热管和改进吸收循环结构三个方面进行了简要的阐述,介绍了三种方式强化传质传热的原理及国内外研究的情况。最后对热管式吸收器应用的可能性做了初步的探讨。