Improvement of performance of dye-sensitized solar cells based on electrodeposited-platinum counter electrode

Platinum nanoparticle was electrodeposited on FTO conducting glass substrate as counter electrode for application in dye-sensitized solar cells (DSSCs). Images of transmission electron microscope (TEM) and Scanning Electron Microscope (SEM) showed that platinum nanoparticle was with the mean size of 20-30 nm and was homogeneously distributed on the surface of the FTO conductive glass sheet. Using such a counter electrode, DSSC showed a 6.40% overall energy conversion efficiency under one sun illumination. It exhibited the same high-performance as the DSSC with a platinum counter electrode prepared by electroplating. Furthermore, the present preparation method for the platinum counter electrode has the advantage of low platinum loading and transparence.     

Fabrication of high performance Pt counter electrodes on conductive plastic substrate for flexible dye-sensitized solar cells

Pt counter electrodes (CEs) with different platinum loading have been prepared using chemical reduced method on flexible indium-doped tin oxide coated polyethylene naphthalate (ITO-PEN) for dye-sensitized solar cells (DSSCs). H₂PtCl₆·6H₂O terpineol solutions were screen printed on the transparent ITO-PEN substrates. After drying, H₂PtCl₆ was reduced by treating it in NaBH₄ solution followed by the hydrothermal treatment at 100 °C. The obtained Pt CEs with different Pt-loading (2.4-7.7 μg/cm²) were characterized by SEM, XPS, electrochemical impedance and transmission spectrum measurement. The Pt CEs show high catalytic activity, low charge transfer resistance (0.26-1.38 Ω cm²) and good light transmittance (about 70% at 400-800 nm). The light-to-electricity conversion efficiency of the flexible DSSC fabricated with the prepared Pt CE and the TiO₂ photoanode prepared on Ti substrate by screen printing technique attains 5.41% under the simulated AM 1.5 sunlight, which is almost same as that based on the thermal decomposited Pt CE on FTO-glass. Compared with other methods to prepare Pt CEs, chemical reduced method is simple and suitable for flexible polymer substrates and the large scale preparation of DSSCs.     

Carbon nanotube counter electrode for high-efficient fibrous dye-sensitized solar cells

ABSTRACT: High-efficient fibrous dye-sensitized solar cell with carbon nanotube (CNT) thin films as counter electrodes has been reported. The CNT films were fabricated by coating CNT paste or spraying CNT suspension solution on Ti wires. A fluorine tin oxide-coated CNT underlayer was used to improve the adherence of the CNT layer on Ti substrate for sprayed samples. The charge transfer catalytic behavior of fibrous CNT/Ti counter electrodes to the iodide/triiodide redox pair was carefully studied by electrochemical impedance and current-voltage measurement. The catalytic activity can be enhanced by increasing the amount of CNT loading on substrate. Both the efficiencies of fibrous dye-sensitized solar cells using paste coated and sprayed CNT films as counter electrodes are comparative to that using Pt wires, indicating the feasibility of CNT/Ti wires as fibrous counter electrode for superseding Pt wires.     

A study of TiO2/carbon black composition as counter electrode materials for dye-sensitized solar cells

This study describes a systematic approach of TiO₂/carbon black nanoparticles with respect to the loading amount in order to optimize the catalytic ability of triiodide reduction for dye-sensitized solar cells. In particular, the cell using an optimized TiO₂ and carbon black electrode presents an energy conversion efficiency of 7.4% with a 5:1 ratio of a 40-nm TiO₂ to carbon black. Based on the electrochemical analysis, the charge-transfer resistance of the carbon counter electrode changed based on the carbon black powder content. Electrochemical impedance spectroscopy and cyclic voltammetry study show lower resistance compared to the Pt counter electrode. The obtained nanostructures and photo electrochemical study were characterized.     

Wurtzite copper-zinc-tin sulfide as a superior counter electrode material for dye-sensitized solar cells

Wurtzite and kesterite Cu₂ZnSnS₄ (CZTS) nanocrystals were employed as counter electrode (CE) materials for dye-sensitized solar cells (DSSCs). Compared to kesterite CZTS, the wurtzite CZTS exhibited higher electrocatalytic activity for catalyzing reduction of iodide electrolyte and better conductivity. Accordingly, the DSSC with wurtzite CZTS CE generated higher power conversion efficiency (6.89%) than that of Pt (6.23%) and kesterite CZTS (4.89%) CEs.     

A novel high-performance counter electrode for dye-sensitized solar cells

A novel Pt counter electrode for dye-sensitized solar cells (DSC) was prepared by thermal decomposition of H₂PtCl₆ on NiP-plated glass substrate. The charge-transfer kinetic properties of the platinized NiP-plated glass electrode (Pt/NiP electrode) for triiodide reduction were studied by electrochemical impedance spectroscopy. Pt/NiP electrode has the advantage over the platinized FTO conducting glass electrode (Pt/FTO electrode) in increasing the light reflectance and reducing the sheet resistance leading to improve the light harvest efficiency and the fill factor of the dye-sensitized solar cells effectively. The photon-to-current efficiency and the overall conversion efficiency of DSC using Pt/NiP counter electrode is increased by 20% and 33%, respectively, compared to that of using Pt/FTO counter electrode. Examination of the anodic dissolution and the long-term test on the variation of charge-transfer resistance indicates the good stability of the Pt/NiP electrode in the electrolyte containing iodide/triiodide.     

Electrodeposited Pt for cost-efficient and flexible dye-sensitized solar cells

Pt electrodes were prepared by direct and pulse current electrodeposition for use as counter electrodes in dye-sensitized solar cells. Scanning electron microscope and transmission electron microscope images confirmed the formation of uniform Pt nanoclusters of ∼40 nm composed of 3 nm nanoparticles, when the pulse current electrodeposition method was used, as opposed to the dendritic growth of Pt by the results from direct current electrodeposition. By applying pulse electrodeposited Pt which has a 1.86 times higher surface area compared to direct current electrodeposited Pt, short-circuit current and conversion efficiency were increased from 10.34 to 14.11 mA/cm² and from 3.68 to 5.03%, respectively. In addition, a flexible solar cell with a pulse current electrodeposited Pt counter electrode with a conversion efficiency of 0.86% was demonstrated.     

Micro–meso hierarchical porous carbon as low-cost counter electrode for dye-sensitized solar cells

A micro–meso hierarchical porous carbon with low crystallinity was prepared by a combination of self-assembly and post activation and explored as a counter electrode in dye-sensitized solar cells. Pore structure analysis showed that the pristine mesopores were basically preserved during activation and the micropores were mainly generated within the mesopore wall. Due to its low crystallinity and unique pore-structure including both mesopores and micropores, hierarchical porous carbon exhibited a relatively higher electrocatalytic activity for triiodide reduction, as compared with the pristine mesoporous carbon electrode. This enhanced electrocatalytic activity is beneficial for improving the photovoltaic performance of dye-sensitized solar cells. Under irradiation of 100 mW cm⁻², the dye-sensitized solar cell with hierarchical porous carbon counter electrode showed an overall conversion efficiency of 6.48%, which was 11.5% higher than that of the cell with pristine mesoporous carbon counter electrode.     

Polyaniline nanofiber/carbon film as flexible counter electrodes in platinum-free dye-sensitized solar cells

Efficient transfer of charges from a counter electrode to an electrolyte is a key process during the operation of dye-sensitized solar cells. Here, we develop a flexible counter electrode by electrochemical deposition of polyaniline nanofibers on graphitized polyimide carbon films for use in a tri-iodide reduction. As determined by the electrochemical impedance spectroscopy, the flexible counter electrode exhibited very low charge transfer resistance and series resistance. These results are due to the high electrocatalytic activity of the polyaniline nanofibers and the high conductivity of the flexible graphitized polyimide film. In combination with a dye-sensitized TiO₂ photoelectrode and electrolyte, the photovoltaic device with the polyaniline counter electrode shows an energy conversion efficiency of 6.85% under 1 sun illumination. Short-term stability tests indicate that the photovoltaic device with the polyaniline counter electrode almost maintains its initial performance.     

染料敏化太阳能电池非铂对电极研究进展

对电极作为染料敏化太阳能电池（dye-sensitized solar cell,DSSC）的重要组成部分,对电极材料性能的好坏直接影响着染料敏化太阳能电池的光电转化效率。最常使用的对电极电催化材料是贵金属铂,而铂十分稀少而且价格昂贵,并且铂很容易被碘电解液腐蚀,不利于染料敏化太阳能电池的产业化发展。本文重点综述了2010年以来染料敏化太阳能电池非铂对电极的研究成果,简要说明了对电极在染料敏化太阳能电池中的作用,详细介绍了非铂金属、碳材料、导电聚合物和无机化合物等对电极材料,分析了各类非铂对电极材料的特点、制备工艺、发展前景、优缺点和改进措施。最后提出,继续开发各种成本低、原料易得以及稳定高效的新型非金属对电极材料仍是今后染料敏化太阳能电池研究的一个重要方向。     

Electropolymerization of a poly(3,4-ethylenedioxythiophene) and functionalized, multi-walled, carbon nanotubes counter electrode for dye-sensitized solar cells and characterization of its performance

Composite films of poly(3,4-ethylenedioxythiophene) and functionalized, multi-walled, carbon nanotubes (PEDOT–MWCNT) were fabricated by a simple oxidative electropolymerization method. These films were formed on fluorine-doped, tin oxide, glass substrates as counter electrodes (CEs) of platinum-free, dye-sensitized solar cells (DSSCs). The surface morphology, formation mechanism and electrochemical nature of PEDOT–MWCNT films were investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), cyclic voltammetry (CV) and alternating current (AC) impedance spectroscopy. The SEM and AFM images showed that PEDOT–MWCNT films were more porous than PEDOT films. CV and AC impedance spectroscopy revealed that the PEDOT–MWCNT electrode had higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction and a smaller charge transfer resistance than the PEDOT electrodes. The energy conversion efficiency of the DSSC with a PEDOT–MWCNT CE was 13.0% higher than with a PEDOT CE using the same conditions with a ruthenium sensitizer.     

The effect of foamed cement nanocomposite as counter electrode on the performance of dye-sensitized solar cell

Improper interparticle connection between carbon-based materials, poor interface bonding between the carbon counter electrodes (CEs) and substrate, and low surface area are the main limitations of carbon-based CEs in dye-sensitized solar cells. In this study, we utilized foamed cement and binder for adherence and surface area improvement in carbon-based CEs, such as graphite, multi-walled carbon nanotubes, and carbon black (CB). The results revealed that incorporating foamed cement into carbon materials improved the resistance, short-circuit current density, fill factor, and power conversion efficiency of the device. The porous cement/CB nanocomposite CE with a photoconversion efficiency of 5.51% exhibited the best photovoltaic performance. Moreover, this nanocomposite electrode showed an enhancement catalytic activity by high current density in cyclic voltammogram, low charge transfer resistance $(R_{CT}$) in electrochemical impedance spectroscopy, and high exchange current density in Tafel measurements compared to other electrodes. The porosity of foamed cement has been found to be the main cause of its superior photovoltaic performance, which expands the contact area with the electrode and enables rich ion transport. Additionally, the enhanced performance was due to strong bonding, crack-free deposited films, superior conductivity, and high catalytic activity.     

Polyvinyl pyrrolidone aided preparation of TiO2 films used in flexible dye-sensitized solar cells

Polyvinyl pyrrolidone (PVP) is introduced to low temperature preparation of a good quality TiO₂ film used in flexible dye-sensitized solar cells (DSSCs). The samples are characterized by scanning electron microscopy and UV–vis absorption spectra, the photovoltaic performance of the DSSC is measured. It is found that PVP can improve the dispersion of TiO₂ particles and the adherence of TiO₂ particles to flexible substrate, as well as the adsorption of sensitized dye to TiO₂ film. Additionally, ultraviolet light irradiation can eliminate organics remained on the surface the TiO₂ film and improve the surface state of TiO₂ film. Under an optimal condition, a flexible DSSC using TiO₂ film doped PVP and UV irradiation treated achieves a light-to-electric energy conversion efficiency of 3.02% under irradiation with a simulate solar light intensity of 100 mW cm⁻².     

A flexible graphene/multiwalled carbon nanotube film as a high performance electrode material for supercapacitors

A flexible graphene/multiwalled carbon nanotube (GN/MWCNT) film has been fabricated by flow-directed assembly from a complex dispersion of graphite oxide (GO) and pristine MWCNTs followed by the use of gas-based hydrazine to reduce the GO into GN sheets. The GN/MWCNT (16 wt.% MWCNTs) film characterized by Fourier transformation infrared spectra, X-ray diffraction and scanning electron microscope has a layered structure with MWCNTs uniformly sandwiched between the GN sheets. The MWCNTs in the obtained composite film not only efficiently increase the basal spacing but also bridge the defects for electron transfer between GN sheets, increasing electrolyte/electrode contact area and facilitating transportation of electrolyte ion and electron into the inner region of electrode. Electrochemical data demonstrate that the GN/MWCNT film possesses a specific capacitance of 265 F g⁻¹ at 0.1 A g⁻¹ and a good rate capability (49% capacity retention at 50 A g⁻¹), and displays an excellent specific capacitance retention of 97% after 2000 continuous charge/discharge cycles. The results of electrochemical measurements indicate that the freestanding GN/MWCNT film has a potential application in flexible energy storage devices.     

Electrophoretic deposition of carbon nanotubes films as counter electrodes of dye-sensitized solar cells

Carbon nanotubes (CNTs) films have been successfully fabricated by electrophoretic deposition (EPD) technique and used as counter electrodes of dye-sensitized solar cells (DSSCs). The CNTs counter electrodes consisting of a large number of bamboo-like structures with defect-rich edge planes exhibit a highly interconnected network structure with high electrical conductivity and good catalytic activity. A high photovoltaic conversion efficiency of 7.03% is achieved for DSSCs based on the CNTs counter electrodes, which is comparable to the cell based on conventional Pt counter electrode at one sun (AM 1.5G, 100 mW cm⁻²). The results suggest that the present synthetic strategy provides a potential feasibility for the fabrication of low-cost flexible counter electrodes of DSSCs using a facile deposition technique from an environmentally “friendly” solution at low temperature.     

High-performance and low platinum loading electrodeposited-Pt counter electrodes for dye-sensitized solar cells

This study demonstrates platinum (Pt) counter electrodes with low charge-transfer resistance (R_ct), low Pt loading and high active surface area can be obtained within 30 s by using the direct-current deposition in the presence of 3-(2-aminoethylamino)propyl-methyldimethoxysilane (Me-EDA-Si) as an additive. The addition of appropriate Me-EDA-Si can not only enhance the current efficiency but also inhibit the growth of semicircle-like grains, thus resulting in Pt electrode with high active surface area. Consequently, the dye-sensitized solar cells (DSSCs) fabricated with so-prepared Pt electrodes exhibited cell efficiency of 7.39% while 0.01 vol% Me-EDA-Si was added, which is much superior to that with sputtered-Pt electrodes under the same assembly conditions.     

Nanocomposites of Bi5FeTi3O15 with MoS2 as novel Pt-free counter electrode in dye-sensitized solar cells

Bi₅FeTi₃O₁₅ (BFTO) nanofibers with diameters in the range of 40–100 nm have been fabricated by sol-gel based electrospinning technique. The structure and morphology of the nanofibers were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The MoS₂ nanoparticles are uniformly dispersed into the BFTO, forming nanocomposites. The optical bandgap of the nanocomposites decreases as MoS₂ content increases. The nanocomposites with different MoS₂ contents serve as low-cost counter electrodes (CEs) for dye-sensitized solar cells (DSSCs). Through photocurrent–voltage curves, electrochemical impedance spectroscopy and Tafel curves, the performance of the CEs indicates that the charge transfer resistance on the electrolyte-electrode interface lower and the catalytic activity for reduction of triiodide to iodide enhance with the increase of MoS₂ concentration. The DSSC with the CE exhibits a power conversion efficiency of 5.20% after the optimization of the content of MoS₂, which is almost 24 times larger than that of the pure BFTO CE.     

A novel hierarchical Pt- and FTO-free counter electrode for dye-sensitized solar cell

A novel hierarchical Pt- and FTO-free counter electrode (CE) for the dye-sensitized solar cell (DSSC) was prepared by spin coating the mixture of TiO₂ nanoparticles and poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) solution onto the glass substrate. Compared with traditional Pt/FTO CE, the cost of the new CE is dramatically reduced by the application of bilayer TiO₂-PEDOT:PSS/PEDOT:PSS film and the glass substrate. The sheet resistance of this composite film is 35 Ω sq⁻¹ and is low enough to be used as an electrode. The surface morphologies of TiO₂-PEDOT:PSS layer and modified PEDOT:PSS layer were characterized by scanning electron microscope, which shows that the former had larger surface areas than the latter. Electrochemical impedance spectra and Tafel polarization curves prove that the catalytic activity of TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE is higher than that of PEDOT:PSS/FTO CE and is similar to Pt/FTO CE''s. This new fabricated device with TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE achieves a high power conversion efficiency (PCE) of 4.67%, reaching 91.39% of DSSC with Pt/FTO CE (5.11%).     

The preparation of titania nanotubes and its application in flexible dye-sensitized solar cells

Anatase titania nanotube (TNT) is prepared by two-steps hydrothermal growth method. Using the TNTs and titania particles (P25), a highly stable and uniform titania colloid without any sedimentation in 180 days is prepared by hydrothermal treatment. Based on the titania colloid, a flexible dye-sensitized solar cell (DSSC) is fabricated at low temperature. The influence of preparation conditions on the properties of TNTs and titania colloid is discussed by transmitting electron microscopy, scanning electron microscopy, selected area electron diffraction, X-ray diffraction, UV-vis absorption spectra, and Brunauer-Emmet-Teller surface area measurements. Under an optimized condition, a flexible DSSC with light-to-electric energy conversion efficiency of 4.0% is achieved under a simulated solar light irradiation of 100 mW cm⁻² (AM 1.5).     

Highly efficient bio-based porous carbon hybridized with tungsten carbide as counter electrode for dye-sensitized solar cell

Bio-based porous carbon (C_MA and C_TA) are successfully prepared from waste carton via microwave-assisted activation (MA) and two-step chemical activation (TA) methods, respectively. The as-prepared C_TA sample exhibits higher specific surface area (824.16 m² g⁻¹) and larger total pore volume (0.71 cm³ g⁻¹), as compared with those of the C_MA sample (655.36 m² g⁻¹ and 0.62 cm³ g⁻¹, correspondingly). The higher specific surface area could provide more catalytic sites; thus, the dye-sensitized solar cell (DSSC) assembled with a C_TA counter electrode (CE) deliver a power conversion efficiency (PCE) of 6.76%, surpass the C_MA-based DSSC (6.19%). Further, tungsten carbide (WC) are introduced into C_TA and C_MA to form hybrid catalysts (WC/C_TA and WC/C_MA, respectively) in order to improve their catalytic activities. Benefitting from the synergistic effect of bio-based porous carbon and WC, the DSSCs with WC/C_TA and WC/C_MA CEs exhibit superior PCE values of 7.32% and 6.85%, respectively, close to Pt (7.51%). This work provides an effective strategy for synthesizing low-cost and high-performance hybrid catalysts from bio-based carbon to achieve resource utilization of biomass waste in new energy fields.