Preparation of photoresist polymer by a photoreactive monomer containing N,N-diethyldithiocarbamate group

A novel photosensitive monomer with a pendant photoreactive diethyldithiocarbamoyl group, VBDC, was synthesized and copolymerized with some vinyl monomers by AIBN. The copolymers obtained have efficient photocrosslinking abilities, and are thermally stable. Therefore, there was no loss of dithiocarbamoyl group during radical polymerization, and the polymerization proceeded through vinyl group. The degree of photocrosslinking was proportional to the concentration of the photosensitive group, but photosensitivity of the polymer was not. Water-soluble photoreactive copolymers, VBDC with AAm or MA, were also prepared. AAm copolymer has a good photosensitivity by only 3 mol % VBDC incorporation. Photocrosslinking yields of these polymers depend on the viscosity of original polymers except in the case of low concentration of VBDC. The relation between copolymer composition and glass transition temperature was also investigated. From the investigation of T_g, it was concluded that the copolymer structure largely affected on ΔT_g. The mechanism of photocrosslinking was studied by photodecomposition of benzyl N, N-diethyldithiocarbamate, and the result that the decreases of sulfur content clearly related to photocrosslinking points was also obtained.     

Preparation and electrochemical characterization of Ti/Ru x Mn1−x O2 electrodes

DSA^® type electrodes of ruthenium–manganese mixed oxides (30 at % Ru < 100) supported on titanium were prepared by the spray-pyrolysis technique, using Ru(NO)(OH) _x (NO₃)_3–x and Mn(NO₃)₂ as precursors. Electrodes were characterized by SEM, XRD and cyclic voltammetry. Their behaviour as anode for the chlorine and oxygen evolution reactions was also evaluated by polarization curves. The stability of the mixed oxides was determined through accelerated tests of service life. It has been verified that the best performance on the apparent electrocatalytic activity of both reactions as well as on stability is achieved at a composition of about 70% Ru.     

Coagulation performance of cationic polyelectrolyte/TiO2 nanocomposites prepared under LED irradiation

A series of acrylic-based cationic polyelectrolyte nanocomposites including water-soluble monomers acrylamide (AAm) and 2-acryloyloxyethyltrimethylammonium chloride (DAC) with different mole percent of DAC (30, 40, and 45%) in feed were produced using TiO₂ nanoparticles (0.018, 0.037, and 0.11 wt%) as photoinitiator in the aqueous solution of monomers and named as p(ADT)_1–9. The LED light at 365 nm was used for photocatalysis activation of TiO₂ nanoparticles. Structure and morphology of the synthetic polyelectrolyte were characterized by FT-IR, NMR, TGA, FESEM-EDX, and TEM. The other properties of synthetic polyelectrolyte such as molecular weight, viscosity, charge density, AAm/DAC molar ratio in copolymers, reactivity ratio values for the AAm and DAC monomers, and polymerization degree were measured. Furthermore, coagulation performance of these polyelectrolytes was investigated in soil suspension (1,000 ml, initial turbidity = 1,715 NTU). The prepared nanocomposites enhanced the coagulation of soil suspension up to 99.5% in low dosages. The best turbidity removal efficiencies (TRE) between 99.5–99.77% were achieved by p(ADT)₃ conatining 30% DAC and 0.11 wt% TiO₂. Decreasing the temperature from room temperature to 0°C led to an increase in TRE from 98 to 99.8%. Also, increasing the pH from 4 to 12 led to a decrease in TRE from 99.86 to 94%.     

Preparation of supported gold catalysts from gold complexes and their catalytic activities for CO oxidation

A phosphine-stabilized mononuclear gold complex Au(PPh₃)(NO₃) (1) and a phosphine-stabilized gold cluster [Aug(PPh₃)₈](NO₃)₃ (2) were used as precursors for preparation of supported gold catalysts. Both complexes 1 and 2 supported on inorganic oxides such as -Fe₂O₃, TiO₂, and SiO₂ were inactive for CO oxidation, whereas the 1 or 2/ oxides treated under air or CO or 5% h₂/Ar atmosphere were found to be active for CO oxidation. The catalytic activity depended on not only the treatment conditions but also the kinds of the precursor and the supports used. The catalysts derived from 1 showed higher activity than those derived from 2. -Fe₂O₃ and TiO₂ were much more efficient supports than SiO₂ for the gold particles which were characterized by XRD and EXAFS.     

Phosphonated poly(1,6-heptadiyne) derivatives prepared by metathesis polymerization for nonlinear optics

Summary Poly(triethyldipropargylphosphonoacetate) (TDPA), poly[(tetraethyl dipropargylmethylenediphosphonate) (TDMDP) were prepared by metathesis polymerization using transition-metal catalysts. MoCl₅-based catalyst systems were more effective for the polymerization of these monomers than WCl₆-based catalyst systems. Resulting polymers exhibited good solubility in common organic solvents and could be easily cast on glass plates to give thin films. Third-harmonic Maker fringe technique was used to measure third-order nonlinear susceptibility,x ⁽³⁾, for thin film of poly(TDPA). Thex ⁽³⁾ was evaluated to be 3.4x10^-11 esu at incident wavelength of 1.907m.     

Atom transfer radical polymerization by [RuCl<Subscript>2</Subscript>(PPh<Subscript>3</Subscript>)<Subscript>2</Subscript>(amine)] catalysts: Cyclic amines as tuner of reactivity

Atom transfer radical polymerizations (ATRP) of styrene (St) and methyl methacrylate (MMA) mediated by [RuCl₂(PPh₃)₂(amine)] complexes, with amine = pyrrolidine (1), piperidine (2), or perhydroazepine (3), were investigated as a function of time, temperature, and concentrations of monomers and 2-bromoisobutyrate as initiator. The plots of ln([M]₀/[M]) vs. time and molecular weights vs. monomer conversion were linear and the dispersity indexes decreased with increasing monomer conversions. The complexes 1, 2, and 3 were able to mediate the polymerizations with acceptable rate and level of control. Differences in the rate and control of polymerization were observed in the order 3 > 2 > 1 for both monomers. The activities were discussed considering the steric hindrance and electronic characteristics of the amines as ancillary ligands in the metal centres, considering studies by cyclic voltammetry and NMR.     

NaOH modified P(acrylamide) hydrogel matrices for in situ metal nanoparticles preparation and their use in H2 generation from hydrolysis of NaBH4

Crosslinked poly(acrylamide) (p(AAm)) as neutral hydrogel is synthesized via photo polymerization technique, and the amide groups within p(AAm) matrices are converted to strongly ionizable carboxylic acids groups via facile modification route by simple treatment of NaOH to obtained NaOH‐p(AAm) hydrogels. Because of the highly ionizable nature of carboxylate groups within mod‐p(AAm), the swelling and metal ion absorbing capacities are increased tremendously, almost 40 and 7.5 folds, respectively. The Co(II) and Ni(II) metal ions are loaded into NaOH‐p(AAm) hydrogels, and are treated with NaBH₄ to form corresponding metal nanoparticles in situ within mod‐p(AAm) matrices, and used in H₂ generation production from hydrolysis of NaBH₄. Various parameters such as functionality of polymeric matrices, the kinds and the amount of metal nanoparticles, and the temperature effecting the H₂ generation are investigated. Comparable low E_a with the similar researches in the literature, E_a = 20.07 ± 0.05 kJ mol^?1 is obtained in NaBH₄ hydrolysis catalyzed by NaOH‐p(AAM)‐Co composite system. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41106.     

An X-ray photoelectron spectroscopy study of poly(methyl methacrylate) surface modified by 193-nm laser radiation

Summary The swelling and equilibrium mechanical behaviour of networks of copolymers of acrylamide (AAm) with a ionic crosslinker — sodium salt of 2,2-bisacrylamidopropionic acid (I) in water-ethanol mixtures was investigated. Two series of networks were prepared. While in series 1 AAm and ionic crosslinker were copolymerized (mole fraction x _I=0.005 to 0.1), in series 2, AAm, ionic crosslinker and non-ionic crosslinker — methylenebisacrylamide (MBAAm) — were copolymerized in such way that x _I + x _MBAAm = 0.05 (x _I varied from 0 to 0.05). In the region x _I0.01 the phase transition was observed for both series. As expected, for networks of series 2 with constant crosslinker concentration the extent of transition (jumpwise change of the volume of the gel) increases with increasing charge concentration, x _I. On the other hand, for samples of series 1 this extent slightly decreases with x _I which means that the effect of increasing crosslinking density on the swelling is greater than that of increasing charge concentration. The critical ethanol concentration at which collapse takes place, e _c, increases with x _I in both series. The jumpwise change in the gel volume is accompanied by a similar change in the equilibrium modulus of the gel.     

A role of surface nitrite and nitrate complexes in NOx selective catalytic reduction by hydrocarbons under oxygen excess

NO adsorption over three types of catalytic systems, such as cation-exchanged zeolites, transition metal oxides supported on -Al₂O₃, and partially stabilised tetragonal ZrO₂ (PSZ) was studied by using the TPD method. NO forms several surface complexes having different desorption temperatures. TPD results compared with catalytic properties of these systems in the selective reduction of NO _x by propane under oxygen excess showed that strongly bound nitrites and nitrates appeared to be true intermediates in this reaction.     

Synthesis,characterization, and ligating behavior of poly[N,N‐p‐phenylene bisacryl (methacryl)amide]

Monomers of diacylated amine were synthesized by the reaction of acryloyl chloride or methacryloyl chloride with p‐phenylenediamine. Heating DMF solution of these monomers at 75°C in the presence of AIBN as an initiator gave the corresponding polymer. The solid metallopolymer complexes with different metal salts were isolated either by the in situ addition of the monomer, metal salt, and initiator at 75°C or by the reaction of the isolated polymer with the metal salt at 150°C. The monomers, polymers, and their metallopolymer compounds were characterized using elemental analysis, IR, NMR (¹H and ¹³C), and MS spectral measurements in addition to thermal analysis. The IR data showed that the coordinating atoms of the polymer are dependent on the reaction temperature. The ion selectivity of the isolated polymers toward different metal ions either for a single metal ion or in a mixture as aqueous solutions are studied by the batch techniques. Energy dispersive spectroscopy (EDS) measurements showed that both polymers are more selective to Hg²⁺ and Pb²⁺. The morphology of the polymers and their metallopolymer complexes at different temperature was also studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2412–2422, 2006     

The role of metal oxides in promoting a copper catalyst for methanol synthesis

The coverage of oxygen formed on the surface of catalysts during methanol synthesis from CO₂ has been measured for copper-based catalysts including various metal oxides using a method called reactive frontal chromatography (RFC). An excellent correlation between the specific activity for methanol synthesis and the oxygen coverage () was obtained, where the activity increased linearly with oxygen coverage at<0.16 and then decreased at>0.18. The results strongly indicate that the support effect or addition of metal oxides revealed in methanol synthesis over copper catalysts is ascribed to the ratio of Cu⁺ to Cu⁰ on the surface of copper particles.     

Synthesis of poly(tetrahydrofuran-b-ε-caprolactone) macromonomer via the Sml2-induced transformation

Summary A novel well-defined macromonomer consisting of different types of monomers in polymerization mechanisms was synthesized for the first time through the SmI₂-induced transformation. The macromonomer, -methacryloylpoly-(tetrahydrofuran-b--caprolactone), was prepared by the reaction of methacryloyl chloride with living poly(tetrahydrofuran-b--caprolactone) [poly(THF-b-CL)] which was obtained by the two-electron reduction of the cationic growing center of poly(THF) by samarium iodide (SmI₂) followed by the polymerization of CL. ¹H NMR analysis indicated the quantitative introduction of the methacryloyl group onto the polymer end. The molecular weight distribution of the macromonomer was relatively narrow, and the unit ratio of THF to CL could be controlled by both polymerization time of THF and the amount of CL, resulting from the living nature of both CL- and THF-polymerizations. Radical copolymerization of the produced macromonomers with methyl methacrylate in the presence of AIBN resulted in a polymethacrylate backbone grafted with poly(THF-b-CL) block copolymers.     

Influence of ruthenium alkylidene complexes bearing tricyclohexylphosphine or 3-bromopyridine ligand on the properties of fluorine containing polymers

The catalytic performance of ruthenium alkylidene complexes bearing tricyclohexylphosphine or 3-bromopyridine ligand in the ring opening metathesis polymerization (ROMP) of fluorine containing monomers, exo-N-4-fluorophenyl-7-oxanorbornene-5,6-dicarboximide (FPhONDI) and exo-N-4-fluorophenyl-norbornene-5,6-dicarboximide (FPhNDI) was investigated. Pure monomers were subjected to ROMP with RuCl₂(PCy₃)₂(CHPh) (I), RuCl₂(PCy₃)(H₂IMes)(CHPh) (II), RuCl₂(3-Br-py)₂(PCy₃)(CHPh) (III) and RuCl₂(3-Br-py)₂(H₂IMes)(CHPh) (IV). The polymers were fully characterized using NMR, DSC, SEM and GPC. Catalysts I–IV displayed significant ROMP activity, allowing for the synthesis of the corresponding polymers with polydispersity indices (PDIs) in the range of 1.4–4.0. High molecular weight polymers (Mw up to 4.95 x10⁵) were prepared in yields up to 90 %, depending on the initiator and monomer used.     

Preparation of high 1,2-orientation butadiene-styrene copolymer by coordination copolymerization with molybdenum-based catalytic system

In this study, with Mo-based catalytic systems consisting of molybdenum pentachloride (MoCl₅) as the main catalyst, alkyl aluminum as the cocatalyst and organophosphorus compound as the ligand, high 1,2-orientation butadiene (Bd)-styrene (St) copolymers were prepared by the coordination polymerization. The effects of phosphorous ligand, alkyl aluminum, polymerization temperature, polymerization time and monomers feed ratios on the monomer conversion and intrinsic viscosity of copolymers were explored in detail. The experimental results indicated that with MoCl₅•TBP (tributyl phosphate)/Al(OPhCH₃)(i-Bu)₂ as the catalytic system to initiate Bd-St copolymerization, the reactivity ratios of butadiene and styrene monomers are 3.64 and 0.16, and the 1,2-structural content in the resulting copolymers is over 80%, regarded as high 1,2-orientation Bd-St copolymers. All these results provided a basis for the design of catalyst used to prepare high 1,2-orientation Bd-St rubber. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48897.     

Neutral Pd(II) and Ni(II) Acetylide Catalysts for the Polymerization of Methyl Methacrylate

Homogenous polymerization of methyl methacrylate using Pd(II)- and Ni(II)-based acetylide complexes as initiators has been investigated. M(PR'₃)₂(CCR)₂ (M=Pd, Ni; R'=PPh₃, Pn-Bu₃; R=Ph, CH₂OH, CH₂OOCCH₃, CH₂OOCPh, CH₂OOCPhOH-o) were found to be a novel type of effective initiators for the polymerization of methyl methacrylate. Among them, Pd(C CPh)₂(PPh₃)₂ (PPP) shows the highest activity in the MMA polymerization and the PMMA obtained is a syndiotactic polymer with high number-average molecular weight (M _n) of 14.1 × 10⁴. Some features and kinetic behavior of MMA polymerization initiated by PPP were studied in detail. The polymerization reaction is first-order with respect to both [PPP] and [MMA]. Radical polymerization mechanism is proposed.     

Synthesis and electrochemistry of grafted copolymers of cellulose with 4-vinylpyridine, 1-vinylimidazole, 1-vinyl-2-pyrrolidinone,and 9-vinylcarbazole

Some new cellulosic materials, suitable for the adsorption of noble metal ions, were syn-thesized by chemical and electrochemical modification of cellulose. The polymerizable groups were introduced in cellulose with ∼ 80% yield of substitution by esterification with acryloyl chloride. The vinyl monomers (4-vinylpyridine, 1-vinylimidazole, 1-vinyl-2-pyrrolidinone, and 9-vinylcarbazole) were readily grafted into cellulose acrylate via radical polymerization in acetonitrile. The grafted copolymers of cellulose with 4-vinylpyridine and 4-vinylimidazole were reacted with methyl iodide and the corresponding 1-methylpyridinium iodide ( 6 ) and 3-methylimidazolium iodide ( 7 ) copolymers of cellulose were obtained. Copolymers 6 and 7 were transformed into new polymeric regents, differing in anions (ClO, CF₃COO⁻, NO, p-TsO⁻, BF, PF) by using a supporting electrolyte carrying the desired anions through the ion-exchange-electrochemical oxidation of the released iodide at a controlled anodic potential. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of maleylated cellulose-<Emphasis Type="Italic">g</Emphasis>-polyacrylamide hydrogel using TiO<Subscript>2</Subscript> nanoparticles under sunlight

Graft polymerization onto the cellulose is one way to produce semisynthetic copolymers and semiconductors were hardly used as initiators. Maleylated cellulose (MC) with different degree of carboxyl groups was synthesized and degree of carboxyl groups was determined using titration method. Then the graft copolymers of acrylamide (AM) on MC were synthesized by titanium dioxide semiconductor photoinitiator in aqueous suspension under sunlight. The effect of different parameters, such as the degree of carboxyl groups, degassing of atmosphere, reactor type, light source, MC/AM ratio, and initiator concentration, was evaluated in the synthesis of graft copolymers. MC with a high degree of carboxyl groups about 2.8 mmol g^?1 was selected for graft photopolymerization. Maximum monomer conversion (55%) for Maleylated cellulose-g-polyacrylamide (MC-g-PAM) was achieved with 0.5 mg TiO₂, MC/AM = 0.056, argon atmosphere, sunlight source, and double quartz tube reactor. The maximum amount of equilibrium swelling (41 g g^?1) was achieved for MC-g-PAM with 34% monomer conversion. The resulting graft copolymers were characterized by FT-IR, SEM, and TGA. Synthesis of MC-g-PAM using TiO₂ nanoparticles (NPs) as the initiator was done successfully that shows the TiO₂ NPs are useable in graft polymerization of acrylamide monomers onto the MC under sunlight.     

Synthesis and self-assembly of miktoarm star copolymers of (polyethylene)2−(polystyrene)2

We report on the synthesis and self-assembly of a novel well-defined miktoarm star copolymer of (polyethylene)₂−(polystyrene)₂, (PE)₂−(PS)₂, with two linear crystalline PE segments and two PS segments as the building blocks based on chain shuttling ethylene polymerization (CSEP), click reaction and atom transfer radical polymerization (ATRP). Initially, alkynyl-terminated PE (PE-) was synthesized via the esterification of pentynoic acid with hydroxyl-terminated PE (PE−OH), which was prepared using CSEP with 2,6-bis[1-(2,6-dimethylphenyl) imino ethyl] pyridine iron (II) dichloride/methylaluminoxane/diethyl zinc and subsequent in situ oxidation with oxygen. (PE)₂−(OH)₂ was then obtained by the click reaction of PE- with diazido and dihydroxyl containing coupling agent. The two hydroxyl groups in (PE)₂−(OH)₂ were then converted into bromisobutyrate by esterification. At last, the (PE)₂−(PS)₂ miktoarm star copolymers were synthesized by ATRP of styrene initiated from (PE)₂−Br₂ macroinitiator. All the intermediates and final products were characterized by ¹H NMR and gel permeation chromatography (GPC). The self-assembly behavior was studied by dynamic light scattering (DLS) and atomic force microscopy (AFM). The crystallization of the (PE)₂−(PS)₂ miktoarm star copolymers was studied by differential scanning calorimetry (DSC).     

High-refractive quinolinone-based polymers for ophthalmic devices

Seven novel high refractive index (HRI) acrylic monomers, comprising the quinolinone structural motive, have been synthesized and characterized. Cross-linked homo- as well as copolymers were prepared by photochemical bulk polymerization. The homopolymers show refractive indices at 589 nm (n ₅₈₉) ranging from 1.60 up to 1.68, glass transition temperatures (T _g) from 52 to 76 °C, and Abbe numbers (ν _Abbe) of 19 to 25. Due to these parameters, the homopolymers are not suitable to be used directly for intraocular lens (IOL) manufacture, but the quinolinone monomers may be used as high refractive index components in copolymers. Potential mixtures were calculated theoretically and one example, a copolymer with PEA and PEGPEA, was prepared and characterized. The experimentally found values were T _g?=?24 °C, n ₅₈₉?=?1.593, and ν _Abbe?=?28.3. Interestingly, the quinolinone compound which does not have any spacer between the polymerizable group and the high refractive index group appears to be the most useful one. The lightfastness of the new material fulfills the demands for IOLs. Quinolinone derivatives are promising new comonomers for high refractive index copolymers.     

Copolymerizations of ethylene with α-olefin-ω-ols by highly active vanadium(III) catalysts bearing [N,O] bidentate chelated ligands

The copolymerizations of ethylene with polar hydroxyl monomers such as 10-undecen-1-ol, 5-hexen-1-ol and 3-buten-1-ol were investigated by the vanadium(III) catalysts bearing bidentate [N,O] ligands (1, [PhNC(CH₃)CHC(Ph)O]VCl₂(THF)₂; 2, [PhNCHC₆H₄O]VCl₂(THF)₂; 3, [PhNCHC(Ph)CHO]VCl₂(THF)₂). The polar monomers were pretreated by alkylaluminum before the polymerization. High catalytic activities and efficient comonomer incorporations can be easily obtained by changing monomer masking reagents and polymerization conditions in the presence of diethylaluminium chloride as a cocatalyst. The longer the spacer group, the higher the incorporation of the monomer. Under the mild conditions, the incorporation level of 10-undecen-1-ol reached 13.9 mol% in the resultant copolymers was obtained. The reactivity ratios of copolymerization (r₁ = 41.4, r₂ = 0.02, r₁r₂ = 0.83) were evaluated by Fineman–Ross method. According to ¹³C NMR spectra, polar units were located both on the main chain and at the chain end. The end-hydroxylated polymers were probably obtained due to the formation of dormant species after the insertion of the comonomer followed by the chain transfer to alkylaluminum. In addition, the signals derived from polar monomer inverse insertion were detected for the first time.