Er3+掺杂ZnWO4的合成及光催化活性研究

通过水热法合成了不同浓度Er³⁺掺杂ZnWO₄纳米棒, 并通过XRD、TEM和DRS等对其进行了表征。通过在模拟太阳光照射下光降解RhB的速度来检测ZnWO₄样品的光催化活性, 研究了Er³⁺掺杂浓度对ZnWO₄催化活性的影响。实验结果表明, 当Er³⁺掺杂浓度为2mol%时, 其光催化性能最好, 因为引进Er³⁺后, Er³⁺加快了电荷分离效率。     

棒状结构NaGdF4:Yb3+,Er3+上转换发光性能的研究

以乙二胺四乙酸二钠(EDTD-2Na)为螯合剂,采用水热法合成了棒状结构的NaGdF₄:Yb³⁺,Er³⁺纳米粉末。分别借助X射线衍射(XRD)、荧光光谱仪(PL)和扫描显微镜(SEM)对其晶体结构、发光强度和表面形貌进行分析和表征。探究了稀土前驱体、水热温度和水热时间的实验条件对NaGdF₄:Yb³⁺,Er³⁺纳米粉末上转换发光强度的影响;研究了氟源和钠源对NaGdF₄:Yb³⁺,Er³⁺晶体形貌和上转换发光强度的改善;同时,采用煅烧处理的方法,进一步探究样品的形貌和发光强度收到的影响。实验结果表明NH₄F与NaOH作为氟源和钠源及200℃煅烧1 h得到的棒状结构NaGdF₄:Yb³⁺,Er³⁺的发光强度最好,色坐标(CIE)绿色发光强度从84%提升到94.88%。     

Er3+掺杂TiO2空心球的制备及其光催化性能研究

以钛酸四丁酯、氧化铒、硝酸等为原料, 采用碳球模板法制备了TiO₂: Er³⁺空心球材料, 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)等测试方法, 对样品的结构和形貌进行了表征。并利用紫外-可见(UV-Vis)分光光度计考察了TiO₂: Er³⁺空心球材料在催化染料罗丹明B、亚甲基蓝、茜素红、甲基橙的脱色降解过程中的应用性能。系统研究了Er³⁺掺杂浓度、不同离子型染料和染料水溶液的pH等因素对催化降解效率的影响。实验结果表明: 经600℃煅烧3 h制备的TiO₂: Er³⁺为锐钛矿晶型, 空心球结构, 尺寸均匀, 粒径约为120 nm, 比表面积约为60.5 m²/g; Er³⁺掺杂量为0.5mol%的样品对甲基橙染料的催化降解效率最高; 对四种不同离子型染料, 茜素红的催化降解效果显著, 在紫外光照射下, 催化效率较未掺杂Er³⁺的TiO₂提高了约30%。     

Er3+/Yb3+共掺杂Ca0.5Gd(WO4)2荧光粉的发光性能和温度特性

上转换发光材料由于具备独特的热敏特性而被应用于非接触式光学温度传感技术,其中Ca_0.5Gd(WO₄)₂具有良好的热稳定性和光学特性,非常适合作为温度传感器的基质材料。本工作采用高温固相法成功制备了Er³⁺、Yb³⁺共掺杂Ca_0.5Gd(WO₄)₂荧光粉,研究了不同Yb³⁺掺杂浓度对样品物相结构、微观形貌和发光性能的影响。随着Yb³⁺掺杂浓度的增加,Ca_0.5Gd(WO₄)₂∶Er³⁺/Yb³⁺荧光粉的上转换和近红外发光强度先增加后减小,在Yb³⁺掺杂浓度为10%(摩尔分数,下同)时,发光强度均出现最大值。根据泵浦功率与发光强度的依赖关系可以得出,Er³⁺的上转换发光属于双光子吸收过程。此外,测量了样品Ca_0....     

Gd2O3下转换发光材料的制备及光学性能研究

通过溶胶-凝胶法制备了Er³⁺/Yb³⁺双掺杂的Gd₂O₃下转换发光材料,按照掺杂摩尔百分比n(Gd³⁺)∶n(Er³⁺)∶n(Yb³⁺)=100∶2:x（x=0,3,6,9）调整Yb³⁺的掺杂比例,通过XRD、SEM、荧光光谱和荧光衰减研究了Er³⁺/Yb³⁺双掺对Gd₂O₃发光材料晶体结构、微观形貌、发光性能和量子传递效率的影响。结果表明,Er³⁺/Yb³⁺的掺杂没有改变Gd₂O₃的晶体结构,但使样品的特征衍射峰出现了高角度偏移;所有样品的晶粒尺寸约为65～85 nm,均属于纳米材料;随着Yb³⁺掺杂量的增加,样品在可见光区域和近红外光区域的衍射峰强度均表现出先升高后降低的趋势,其中2Er:3Yb掺杂比例的Gd     

Er3+掺杂弛豫铁电材料PMNT的单晶生长与性能表征

按照0.71Pb(Mg_1/3Nb_2/3)O₃-0.26PbTiO₃-0.03Pb(Er_1/2Nb_1/2)O₃化学式所示组分比例, 采用分步高温固相反应合成出Er³⁺掺杂PMNT多晶, 通过熔体坩埚下降法生长出尺寸φ25 mm×100 mm的Er³⁺掺杂PMNT晶体, Er³⁺离子以三元固溶体组元方式被掺杂进入钙钛矿相铁电体晶格; 测试了Er³⁺掺杂PMNT晶片的介电、压电与铁电性能以及上转换发光性能。结果表明, Er³⁺掺杂PMNT晶体呈现跟三方相纯PMNT晶体相近的介电、压电与铁电性能; 在980 nm激发光作用下, 该掺杂晶体呈现出Er³⁺离子特有的较强上转换荧光发射, 并且极化后掺杂晶体的上转换发光强度得到增强。     

CaF2:Yb3+/Er3+/X(X= Li+, Na+, K+)近红外二区发光性能研究

利用热分解法制备了CaF₂:Yb³⁺/Er³⁺纳米颗粒,通过改变Yb³⁺和Er³⁺的掺杂浓度对其近红外二区(NIR-II)发光性能进行调节,研究结果表明,当Yb³⁺掺杂浓度为20%,Er³⁺掺杂浓度为2%时,在980 nm光源激发下,NIR-II发光性能最强,且纳米颗粒分散性良好,尺寸均匀。然后,进一步研究了不同的碱金属离子(Li⁺、Na⁺、K⁺)共掺杂对其NIR-II发光性能的影响,研究结果表明,Li⁺掺杂因不利于纳米颗粒成核导致NIR-II发光性能降低,Na⁺和K⁺掺杂均有利于NIR-II发光性能提升。相比而言,K⁺离子半径更大,更有利于破坏晶体场的局部对称性,因此,在K⁺共掺杂的情况下NIR-II发光性能最强。     

溶胶-凝胶法制备Gd4Ga2O9: Dy3+白光发射荧光粉及其性能

通过溶胶-凝胶法制备了具有白光发射的Gd₄Ga₂O₉:x%Dy³⁺荧光粉,利用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、能谱仪(EDS)、紫外-可见漫反射光谱(UV-Vis DRS)和荧光光谱等对产物的物相结构、形貌、组分和光学性能进行研究,并分析了Dy³⁺掺杂量对样品的影响。XRD结果表明,所制备的样品为Dy³⁺掺杂的Gd₄Ga₂O₉单斜晶体和少量Ga₂O₃杂质相的混合物。紫外-可见漫反射光谱结果表明制备的Dy³⁺掺杂Gd₄Ga₂O₉晶体是一种光学带隙为5.29 eV的直接带隙半导体。荧光检测结果表明Dy³⁺掺杂Gd₄Ga₂O₉荧光粉可被属于Gd³⁺     

(Bi0.5Na0.5)TiO3:Sm3+无铅压电陶瓷的红光发射特性

采用传统的固相反应烧结方法制备了稀土Sm³⁺掺杂的(Bi_0.5Na_0.5)TiO₃无铅压电陶瓷。系统分析了掺杂浓度、烧结温度和离子补偿对发光特性的影响。稀土Sm³⁺离子的加入实现了(Bi_0.5Na_0.5)TiO₃陶瓷的红绿光发射, 其激发光波段位于400~500 nm范围内, 与已经成熟的蓝光LED芯片的发射光谱充分匹配。当烧结温度为1100℃, Sm³⁺离子的掺杂浓度为0.015 mol时, 陶瓷样品呈现最强的发光强度。同时, 通过Li⁺、Na⁺、K⁺离子进行电荷补偿, 有效提高了陶瓷样品的发光性能, 发光强度随离子半径增大而增强。可见, Sm³⁺掺杂的(Bi_0.5Na_0.5)TiO₃材料在光电集成器件中具有很好的应用前景。     

Eu3+、Dy3+和Er3+对制备堇青石晶相转变的对比表征

以菱镁矿风化石、工业Al₂O₃和SiO₂微粉为原料, 固相反应烧结合成制备堇青石。通过在反应物中分别加入不同含量的Eu₂O₃、Dy₂O₃和Er₂O₃, 研究分析和对比了Eu³⁺、Dy³⁺和Er³⁺对堇青石晶相组成、晶粒大小、晶胞常数、结晶度及显微结构的影响。采用XRD和SEM表征试样中的晶相和显微结构, 利用X'Pert Plus软件对结晶相的晶胞参数和结晶度进行分析, 采用半定量法对试样晶相组成进行计算, 利用Scherrer公式计算堇青石的晶粒大小。结果表明: 由于Eu₂O₃、Dy₂O₃和Er₂O₃的加入, 通过固相反应烧结所得堇青石试样中出现了莫来石相, Eu³⁺、Dy³⁺和Er³⁺对Mg²⁺的置换作用改变了堇青石相晶格常数和晶胞体积。随着添加剂含量的增加, 堇青石结构中液相量增加, 相对结晶度降低, 常温致密度提高, 堇青石晶粒粒径减小。综合对比分析, Eu₂O₃对堇青石晶相转变的影响程度最弱, Er₂O₃对堇青石晶相转变的影响程度最强, 对提高合成堇青石的烧结性和热震稳定性效果最好。     

Ba3Gd(PO4)3:Eu3+荧光粉的合成及发光性质

采用高温固相反应法合成了不同Eu³⁺掺杂浓度的Ba₃Gd(PO₄)₃荧光粉。利用X射线衍射对产生的晶体结构进行了分析, 证实产物为纯相, Eu³⁺的引入没有导致晶体结构的改变。利用Van Uitert模型对⁵D₀能级荧光的浓度猝灭行为进行了研究, 发现浓度猝灭是由于Eu³⁺间交换相互作用所导致。分析了⁵D₀荧光发射的温度依赖, 给出了荧光温度猝灭行为符合横向穿越模型, 并通过非线性拟合获得了激活能。利用Eu³⁺的发射光谱和荧光衰减数据, 计算了⁵D₀→⁷F_J辐射跃迁速率及荧光分支比, 同时得到了光学跃迁强度参数。     

Optical properties of Nd-doped Ca3(VO4)2 single crystal fiber

Optical absorption and photoluminescence of Ca₃(VO₄)₂ single crystal grown by a floating-zone technique and containing Nd³⁺ ions were investigated. High absorption coefficients and broadening of most absorption bands are present at 300 K, while substructures in some of the same bands can be evidenced at 12 K. Most features of measured spectra are characteristic of random occupation of more than a single Ca²⁺ site by the Nd³⁺ ion and of distortions provoked by different charge compensation mechanisms involving oxygen vacancies promotion in the crystal lattice. Nd³⁺ optical properties were studied by using the Judd-Ofelt theory to calculate the spectral parameters relevant for laser applications.     

Spectroscopic investigation of Nd ion in LiNbO3, MgO:LiNbO3 and LiTaO3 single crystals relevant for laser applications

The polarized absorption and luminescence properties of Nd³⁺ doped isostructural LiNbO₃, MgO:LiNbO₃ and LiTaO₃ nonlinear bulk single crystals are reported. Pump-probe experiments associated with the Judd-Ofelt approach are used to estimate two types of room temperature cross sections: polarized emission cross sections of the dominant ⁴F_3/2 → ⁴I_1//2 transition near 1085 and 1093 nm and polarized excited-state absorption cross sections in the same spectral domain and in the green spectral range corresponding to self frequency doubling. Self frequency-doubling results are also given in Nd:LiNbO₃ and Nd:MgO:LiNbO₃ versus sample temperature.     

Up-conversion dynamics in GdAlO3:Er single crystal fibre

Green fluorescence has been obtained under continuous laser excitation in the 780–860 nm range in GdAlO₃:Er³⁺. With the help of the Judd-Ofelt treatment we built a model based on population rate equations to describe its time evolution. We found the intensity parameters to be Ω₂ = 2.045 × 10⁻²⁰ cm², Ω₄ = 1.356 × 10⁻²⁰ cm² Ω₆ = 1. 125 × 10⁻²⁰ cm². Even if a two-photon absorption and a looping mechanism are necessary to well describe the dynamics, the main process responsible for up-conversion is energy transfer between erbium ions.     

Crystal growth and spectral properties of pure and Co-doped Mg3B2O6 crystal

Novel pure and cobalt-doped magnesium borate crystals (Mg₃B₂O₆) have been grown successfully by the Czochralski technique for the first time. Crystal growth, X-ray powder diffraction (XRD) analysis, absorption spectrum, fluorescence spectrum as well as fluorescence decay curve of Co²⁺:Mg₃B₂O₆ (MBO) were described. From the absorption peaks for the octahedral Co²⁺ ions, the crystal-field parameter Dq and the Racah parameter B were estimated to be 943.3 cm⁻¹ and 821.6 cm⁻¹, respectively. The fluorescence lifetime of the transition ⁴T₁(⁴P) → ⁴T₂ centered at 717 nm was measured to be 9.68 ms.     

Fullerane, the Hydrogenated C60 Fullerene: Properties and Astrochemical Considerations

Hydrogenated C₆₀ fullerene, C₆₀H₃₆ was prepared in different solvents using Zn/HCl as reducing agents. The structure of C₆₀H₃₆ was confirmed both by electronic and FT-IR spectroscopy and the purity of the reaction product was checked by HPLC analysis. It has been confirmed that C₆₀H₃₆ is not stable in air, especially in presence of light which enhances the oxidation. The oxidation of C₆₀H₃₆ was studied by FT-IR spectroscopy and by differential scanning calorimetry (DSC) in air; the formation of hydroxyl groups on the fullerene cage and ketonic groups (involving cage breakdown) have been detected. Furthermore, the action of O₃ on C₆₀H₃₆ was investigated and it has been found that O₃ exerts practically the same effect of air but causing an enhanced cage breakdown. The thermal stability of C₆₀H₃₆ was checked by a thermogravimetric analysis (TGA) coupled with a differential thermal analysis (DTA) under N₂ flow. The vaporization of C₆₀H₃₆ occurs at very high temperature: the DTA trace has shown an endothermic peak at 540°C (at a heating rate of 20°C/min). C₆₀H₃₆ shows an electronic absorption spectrum with a maximum at about 217 nm and it is able to match both in position and in half width the peak at 217.5 nm observed in the spectrum of the interstellar extinction of light which was attributed to hydrogenated, radiation processed and thermally annealed carbon dust. Similarly, the absorption spectrum of C₆₀H₃₆ is able to match several infrared emission bands (called UIBs) detected from certain astrophysical objects like the protoplanetary nebulae (PPNe). It is proposed that hydrogenated fullerenes can be used as model compounds in the laboratory simulation studies of interstellar carbon dust.     

Spectroscopic analysis and the effects of color centers on the laser performance of Nd: CaZn2Y2Ge3O12

Spectroscopic and EPR investigations of Nd³⁺-doped CaZn₂Y₂Ge₃O₁₂ (CAZGAR) have been performed. The absorption, fluorescence, excitation spectra and fluorescence lifetime have been measured at room temperature. The Judd-Ofelt theory has been applied to the measured optical absorption intensities to predict the radiative decay rates, branching ratios, and peak stimulated emission cross section from the metastable ⁴F_3/2 state to the ⁴I_9/2 manifold. The fluorescence lifetime of the ⁴F_3/2 level of Nd³⁺ at low concentration in this host was measured to be 285 ± 10 μs, which is longer than that for Nd³⁺: YAG. Color centers located at zinc octahedral sites have been produced in these crystals by ultraviolet irradiation and have been detected by EPR techniques. The effects of the color centers on the potential laser characteristics of this materials are discussed.     

紫外吸收光谱法在线测量SO3的实验研究

基于紫外吸收光谱法对SO₃的在线测量进行了实验研究,搭建了SO3气体发生系统。为提高检测精度,探究了去除测量过程中的各种干扰因素。SO₃与SO₂的特征吸收波段重叠严重,通过合理选择特征吸收波段和光谱反演策略最大程度地去除SO₂对SO₃测量的影响。研究中采用标准曲线法结合单波长法、双波长法和积分光谱法建立了标准曲线。结果表明:积分光谱法的测量误差最小,可优先应用于SO3排放的在线光谱计量分析。     

Permeability measurement in the GHz range for soft-magnetic filmusing the M/C/M inductance-line

This work reports a new technique for measuring permeability of magnetic alloy films above 1 GHz by using an inductance-line, which has a magnetic alloy films(M)/conductor(C)/magnetic alloy films(M) stacked structure and is installed in a microstrip circuit. The imaginary part of the relative permeability μ_r" was estimated from the magnetic absorption in the M/C/M inductance-line, by analyzing its transmission characteristics. The Kramers-Kronig relation was used for the transformation from μ_r" to the real part μ_r '. Complex relative permeability was measured in the 1 MHz-20 GHz frequency range for NiFe-SiO₂, CoZrNb-SiO₂ and CoFe-SiO₂ multilayer films. The μ_r-f characteristics, static relative permeability μ_r"(0) and ferromagnetic resonance frequency f_k values were confirmed to agree with those obtained by the conventional M/C/M technique and by calculation     

Spectroscopic studies of Sm3+-doped phosphate glasses

Optical properties of Sm³⁺ ion in phosphate glassy matrices were studied. The absorption, fluorescence, excitation spectra and decay patterns were obtained at room temperature. The oscillator strengths of the transitions betweenJ manifolds were calculated using Judd-Ofelt theory and compared with the ones obtained experimentally. Various laser intensity parameters such as J-O parameters, radiative transition probabilities, lifetimes, branching ratio, and integrated absorption cross-section were evaluated. Radiative lifetimes of the excited states were determined and used to obtain nonradiative transition rates and quantum yields. Integrated intensity and dynamics of the fluorescence originating from the excited states were also studied as a function of Sm³⁺ concentration.