Effect of annealing temperature and $$\hbox {CdCl}_{2}$$ treatment on the photo-conversion efficiency of $$\hbox {CdTe/Zn}_{0.1}$$CdTe/Zn0.1$$\hbox {Cd}_{0.9}$$Cd0.9S thin film solar cells

We report the effects of annealing in conjunction with \(\hbox {CdCl}_{2}\) treatment on the photovoltaic properties of \(\hbox {CdTe/Zn}_{0.1}\hbox {Cd}_{0.9}\)S thin film solar cells. CdTe layer is subjected to dry \(\hbox {CdCl}_{2}\) treatment by thermal evaporation method and subsequently, heat treated in air using a tube furnace from 400 to \(500{^{\circ }}\hbox {C}\). AFM and XRD results show improved grain size and crystallographic properties of the CdTe film with dry \(\hbox {CdCl}_{2}\) treatment. This recrystallization and grain growth of the CdTe layer upon \(\hbox {CdCl}_{2}\) treatment translates into improved photo-conversion efficiencies of \(\hbox {CdTe/Zn}_{0.1}\hbox {Cd}_{0.9}\)S cell. The results of dry \(\hbox {CdCl}_{2}\) treatment were compared with conventional wet \(\hbox {CdCl}_{2}\) treatment. Photo-conversion efficiency of 5.2% is achieved for dry \(\hbox {CdCl}_{2}\)-treated cells in comparison with 2.4% of wet-treated cell at heat treatment temperature of \(425{^{\circ }}\hbox {C}\).     

Influence of Thermal Annealings in Argon on the Structural and Thermochromic Properties of $$\mathrm{MoO}_{3}$$ Thin Films

The effect of thermal annealing in an inert atmosphere (argon) on the structural and thermochromic properties of \(\hbox {MoO}_{3}\) thin films was investigated. \(\hbox {MoO}_{3}\) thin films were deposited by thermal evaporation in vacuum of \(\hbox {MoO}_{3}\) powders. X-ray diffraction patterns of the films showed the presence of the monoclinic Magneli phase \(\hbox {Mo}_{9}\hbox {O}_{26}\) for annealing temperatures above \(250\,{^{\circ }}\hbox {C}\). Absorbance spectra of the films annealed in argon indicated that their thermochromic response increases with the annealing temperature in the analyzed range (23 \({^{\circ }}\hbox {C}\)–300 \({^{\circ }}\hbox {C}\)), a result opposite to the case of thermal annealings in air, for which case the thermochromic response shows a maximum value around 200 \({^{\circ }}\)C–225 \({^{\circ }}\)C and decreases for higher temperatures. These results are explained in terms of a higher density of oxygen vacancies formed upon thermal treatments in inert atmospheres.     

Thermodynamic Investigation of the Eutectic Mixture of the $$\hbox {LiNO}_{3}$$–$$\hbox {NaNO}_{3}$$NaNO3–$$\hbox {KNO}_{3}$$KNO3–$$\hbox {Ca}(\hbox {NO}_{3})_{2}$$Ca(NO3)2 System

Molten nitrate salt is usually employed as heat transfer or energy storage medium in concentrating solar power systems to improve the overall efficiency of thermoelectric conversion. In the present work, the liquidus curves of the \(\hbox {LiNO}_{3}\)–\(\hbox {NaNO}_{3}\)–\(\hbox {KNO}_{3}\)–\(\hbox {Ca}(\hbox {NO}_{3})_{2}\) system is determined by conformal ionic solution theory according to the solid–liquid equilibrium state of the binary mixture. The calculated eutectic temperature of the mixture is \(93.17\,{^{\circ }}\hbox {C}\), which is close to the experimental value of \(93.22\,{^{\circ }}\hbox {C}\) obtained from differential scanning calorimetry (DSC). Visualization observation experiments reveal that the quaternary eutectic mixture begins to partially melt when the temperature reaches \(50\,{^{\circ }}\hbox {C}\), and the degree of melting increases with temperature. The mixture is completely melted at \(\hbox {130}\,{^{\circ }}\hbox {C}\). The observed changes in the dissolved state at different temperatures correlate well with the DSC heat flow curve fluctuations.     

Characterization and optical properties of $$\hbox {Pr}_{2}\hbox {O}_{3}$$-doped molybdenum lead-borate glasses

\(\hbox {Pr}^{3+}\) doped molybdenum lead-borate glasses with the chemical composition 75PbO?[25–(x \(+\) y)\(\hbox {B}_{2}\hbox {O}_{3}]\)–\(y\hbox {MoO}_{3}\)–\(x\hbox {Pr}_{2}\hbox {O}_{3}\) (where \(x = 0.5\) and 1.0 mol% and \(y = 0\) and 5 mol%) were prepared by conventional melt-quenching technique. Thermal, optical and structural analyses are carried out using DSC, UV and FTIR spectra. The physical parameters, like glass transition \((T_{\mathrm{g}})\), stability factor \((\Delta T)\), optical energy band gap \((E_{\mathrm{gopt}})\), of these glasses have been determined as a function of dopant concentration. The \({T}_{\mathrm{g}}\) and optical energy gaps of these glasses were found to be in the range of 290–350\({^{\circ }}\hbox {C}\) and 2.45–2.7 eV, respectively. Stability of the glass doped with \(\hbox {Pr}^{3+}\) is found to be moderate (\(\sim \)40). The results are discussed using the structural model of Mo–lead-borate glass.     

High-pressure studies of superconductivity in $$\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}$$

\(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\) crystallizes in tetragonal CeOBiS\(_{2}\) structure (S. G. P4/nmm). We have investigated the effect of pressure on magnetization measurements. Our studies suggest improved superconducting properties in polycrystalline samples of \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\). The \(T_{\mathrm{c}}\) in our sample is 5.3 K, at ambient pressure, which is marginal but definite enhancement over \(T_{\mathrm{c}}\) reported earlier (= 5.1 K). The upper critical field \(H_{\mathrm{c}2}\)(0) is greater than 3 T, which is higher than earlier report on this material. As determined from the M–H curve, both \(H_{\mathrm{c}2}\) and \(H_{\mathrm{c}1}\) decrease under external pressure P (0 \(\le P \le \) 1 GPa). We observe a decrease in critical current density and transition temperature on applying pressure in \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\).     

Electrical and Thermal Characteristics of the Insulator–Metal Transition in Crystalline $$\hbox {V}_{2}\hbox {O}_{5}$$ Films

The electrical and thermal properties with respect to the crystallization in \(\hbox {V}_{2}\hbox {O}_{5}\) thin films were investigated by measuring the resistance at different temperatures and applied voltages. The changes in the crystal structure of the films at different temperatures were also explored using Raman measurements. The thermal diffusivity of the crystalline \(\hbox {V}_{2}\hbox {O}_{5}\) film was measured by the nanosecond thermoreflectance method. The microstructures of amorphous and crystalline \(\hbox {V}_{2}\hbox {O}_{5}\) were observed by SEM and XRD measurements. The temperature-dependent Raman spectra revealed that a structural phase transition does not occur in the crystalline film. The resistance measurements of an amorphous film indicated semiconducting behavior, whereas the resistance of the crystalline film revealed a substantial change near \(250\,{^{\circ }}\hbox {C}\), and Ohmic behavior was observed above \(380\,{^{\circ }}\hbox {C}\). This result was due to the metal–insulator transition induced by lattice distortion in the crystalline film, for which \(T_{\mathrm{c}}\) was \(260\,{^{\circ }}\hbox {C}\). \(T_{\mathrm{c}}\) of the film decreased from 260 \({^{\circ }}\hbox {C}\) to \(230\,{^{\circ }}\hbox {C}\) with increasing applied voltage from 0 V to 10 V. Furthermore, the thermal diffusivity of the crystalline film was \(1.67\times 10^{-7}\,\hbox {m}^{2}\cdot \hbox {s}^{-1}\) according to the nanosecond thermoreflectance measurements.     

Effect of annealing treatment on optical properties and microstructural variation of $$\hbox {WO}_{3}/\hbox {Ag}/\hbox {WO}_{3}$$ multilayer nano-films

Structural and optical properties of \(\text {WO}_{3}/\text {Ag}/\text {WO}_{3}\) nano-multilayer composites were investigated for heat mirror applications. \(\text {WO}_{3}/\text {Ag}/\text {WO}_{3}\) thin films were fabricated through a physical vapour deposition method by using electron-beam evaporation at the vacuum chamber at 10\(^{-5}\) Torr. \(\text {WO}_{3}\) nano-layer was fabricated at 40 nm. Annealing treatment was carried out at 100, 200, 300 and 400\(^{\circ }\)C for 1 h after the deposition of first layer of \(\text {WO}_{3}\) on the glass. On \(\text {WO}_{3}\) film, Ag nano-layers with 10, 12 or 14 nm thickness were deposited. Individual layers morphology was investigated using atomic force microscopy (AFM) and deduced that a smoother layer can be achieved after the annealing at 300\(^{\circ }\)C. Ellipsometry analysis was executed to determine both layers, Ag film thickness and inter-diffusion between the \(\text {WO}_{3}\)–Ag–\(\text {WO}_{3}\) layers. It was inferred that there was almost no interfering among the \(\text {WO}_{3}\)–\(\text {WO}_{3 }\) layers in the samples with 12 and 14 nm Ag thickness; while silver was deposited on the annealed \(\text {WO}_{3}\) layer at 300\(^{\circ }\)C. UV–visible spectrophotometer showed that the annealing treatment of the first \(\text {WO}_{3}\) layer enhanced the transparency of films in the visible region. The innovations of the present study have been based on the annealing of the films and finding an optimum thickness for the Ag film at 12–14 nm. Heat mirrors efficiency was assessed according to the principle of their optical behaviour and optimum performance obtained for 14 nm of Ag film, deposited on annealed tungsten oxide at 300\(^{\circ }\)C.     

Fabrication and enhanced photoluminescence properties of $$\hbox {NaLa}(\hbox {MoO}_{4})_{2}$$: $$\hbox {Sm}^{3+}$$Sm3+, $$\hbox {Bi}^{3+}$$Bi3+ phosphors with high efficiency white-light-emitting

The tetragonal scheelite-type \(\hbox {Sm}^{3+}\hbox {/Bi}^{3+}\) ions co-doped with \(\hbox {NaLa}(\hbox {MoO}_{4})_{2}\) phosphors were synthesized by a facile sol–gel and combustion process using citric acid as complexing agent. The crystal structure and morphology of these as-prepared samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Furthermore, UV-absorption and the photoluminescence (PL) properties of these phosphors were systematically investigated and the PL of the phosphors shows strong white light emissions. Efficient energy transfer from the \(\hbox {MoO}_{4}^{2-}\) group or \(\hbox {Bi}^{3+}\) ions to \(\hbox {Sm}^{3+}\) ions was established by PL investigation excited at 405 nm. The PL intensity of the studied materials was investigated as a function of different \(\hbox {Sm}^{3+}\) and \(\hbox {Bi}^{3+}\) concentrations. The PL investigations revealed that the phosphors exhibit apparent characteristic emissions, which is ascribed to the transition from the ground state energy level \(^{4}\hbox {G}_{5/2}\) to excited state energy levels \(^{6}\hbox {H}_{\mathrm{J}}\) (\(J= 5/2, 7/2, 9/2\)) and the \(\hbox {NaLa}(\hbox {MoO}_{4})_{2}\): 4 mol% \(\hbox {Sm}^{3+}\) and \(\hbox {NaLa}(\hbox {MoO}_{4})_{2}\): 4 mol% \(\hbox {Sm}^{3+}\), 8 mol% \(\hbox {Bi}^{3+}\) present white emissions with the CIE coordinates of (0.350, 0.285) and (0.285, 0.229), respectively. The absolute quantum efficiencies of the phosphors are 40% (\(\hbox {NaLa}(\hbox {MoO}_{4})_{2}\): 4 mol% \(\hbox {Sm}^{3+}\)) and 52% (\(\hbox {NaLa}(\hbox {MoO}_{4})_{2}\): 4 mol% \(\hbox {Sm}^{3+}\), 8 mol% \(\hbox {Bi}^{3+}\)), respectively.     

A first-principle investigation into effect of B- and BN-doped $$\hbox {C}_{60}$$ in lowering dehydrogenation of $$\hbox {MXH}_{4}$$MXH4 (where M $$=$$= Na,Li and X $$=$$= Al,B)

The present paper reports the effect of B- and BN-doped \(\hbox {C}_{60}\) as catalysts for lowering the dehydrogenation energy in \(\hbox {MXH}_{4}\) clusters (M = Na and Li, X = Al and B) using density functional calculations. \(\hbox {MXH}_{4}\) interacts strongly with B-doped \(\hbox {C}_{60}\) and weakly with BN-doped \(\hbox {C}_{60}\) in comparison with pure \(\hbox {C}_{60}\) with binding energy 0.56–0.80 and 0.05–0.34 eV, respectively. The hydrogen release energy \((E_{\mathrm{HRE}})\) of \(\hbox {MXH}_{4}\) decreases sharply in the range of 38–49% when adsorbed on B-doped \(\hbox {C}_{60}\); however, with BN-doped \(\hbox {C}_{60}\) the decrease in the \(E_{\mathrm{HRE}}\) varies in the range of 6–20% as compared with pure \(\hbox {MXH}_{4}\) clusters. The hydrogen release energy of second hydrogen atom in \(\hbox {MXH}_{4}\) decreases sharply in the range of 1.7–41% for BN-doped \(\hbox {C}_{60}\) and decreases in the range of 0.2–11.3% for B-doped \(\hbox {C}_{60}\) as compared with pure \(\hbox {MXH}_{4}\) clusters. The results can be explained on the basis of charge transfer within \(\hbox {MXH}_{4}\) cluster and with the doped \(\hbox {C}_{60}\).     

Resistance-switching properties of Bi-doped $$\hbox {SrTiO}_{3}$$ films for non-volatile memory applications with different device structures

\(\hbox {SrTiO}_{3}\) and Bi-doped \(\hbox {SrTiO}_{3}\) films were fabricated with different device structures using the sol–gel method for non-volatile memory applications, and their resistance-switching behaviour, endurance and retention characteristics were investigated. \(\hbox {SrTiO}_{3}\) and \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt have the same phase structure, morphologies and grain size; however, the grain size of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si is slightly larger than those of the \(\hbox {SrTiO}_{3}\) films grown on Si and the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Pt. The \(\hbox {SrTiO}_{3}\) or \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt all exhibit bipolar resistive-switching behaviour and follow the same conductive mechanism; however, the \(\hbox {Ag}/\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}/\hbox {Si}\) device possesses the highest \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of \(10^{5}\) and the best endurance and retention characteristics. The doping of Bi is conducive to enhance the \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of the \(\hbox {SrTiO}_{3}\) films; meanwhile, the Si substrates help improve the endurance and retention characteristics of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films.     

Measurement of the Water Relaxation Time of $${\upvarepsilon }$$-Polylysine Aqueous Solutions

\({\upvarepsilon }\)-Polylysine is an effective food preservative. In this paper, the \({\upbeta }\)-relaxation time of \({\upvarepsilon }\)-polylysine aqueous solutions, which represents the rotational speed of a single water molecule, was measured by broadband dielectric spectroscopy at various temperatures and concentrations. The broadband dielectric spectrum of each sample containing water ranging from 35 wt% to 75 wt% at temperatures ranging from \(0\,^{\circ }\hbox {C}\) to \(25\,^{\circ }\hbox {C}\) was measured using a co-axial semirigid cable probe. The measured dielectric spectra of the samples were composed of several Debye relaxation peaks, including a shortest single molecular rotational relaxation time of water, the \({\upbeta }\)-relaxation time, longer than that of pure water. This result represents that \({\upvarepsilon }\)-polylysine suppresses the molecular kinetics of water. It is also found that the \({\upbeta }\)-relaxation time of an \({\upvarepsilon }\)-polylysine solution that contained more than 35 wt% water showed a typical Arrhenius plot in the temperature range from \(0\,^{\circ }\hbox {C}\) to \(25\,^{\circ }\hbox {C}\). The activation energy of each sample depends on the water content ratio of the sample. As indicated by its long \({\upbeta }\)-relaxation time, \({\upvarepsilon }\)-polylysine is expected to possess high abilities of suppressing freezing and ice coarsening.     

Influence of the conditions of a solid-state synthesis anode material $$\hbox {Li}_{4}\hbox {Ti}_{5}\hbox {O}_{12 }$$ on its electrochemical properties of lithium cells

Lithium–titanium spinel is a promising electrode material for high power and environmentally friendly batteries. We did research on \(\hbox {Li}_{4}\hbox {Ti}_{5}\hbox {O}_{12 }\) (LTO) samples, which were synthesized via solid-state reaction at various conditions in a temperature range from 800 to \(900{^{\circ }}\hbox {C}\) and they were investigated by XRD, SEM, IS, cyclic voltammetry and the galvanostatic charge–discharge tests. X-ray diffractions show that all of the samples have a spinel structure with Fd-3m space group with a small amount of impurities \(\hbox {TiO}_{2}\) (anatase). Lithium ion batteries with LTO-based electrode exhibit excellent reversible capacity of \(\,\sim 180\hbox { mAh}\hbox { g}^{-1}\) in the current density range from 0.1 to 1 C. As an electrode material for rechargeable lithium-ion batteries, LTO-F demonstrates the best rate and cyclic performance from all of the studied samples.     

Facile synthesis and characterization of rough surface $$\mathrm{V}_{2}\hbox {O}_{5}$$ nanomaterials for pseudo-supercapacitor electrode material with high capacitance

\(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials with rough surface were synthesized using commercial \(\hbox {V}_{2}\hbox {O}_{5}\), ethanol (EtOH) and \(\hbox {H}_{2}\hbox {O}\) as the starting materials by a simple hydrothermal route and combination of calcination. The electrochemical properties of \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials as electrodes in a supercapacitor device were measured using cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) method. \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials exhibit the specific capacitance of 423 F \(\hbox {g}^{-1}\) at the current density of 0.5 A \(\hbox {g}^{-1}\) and retain 327 F \(\hbox {g}^{-1}\) even at the high current density of 10 A \(\hbox {g}^{-1}\). The influence of the ratio of \(\hbox {EtOH/H}_{2}\hbox {O}\), the calcined time and temperature on the morphology, purity and electrochemical property of the products is discussed in detail. The results revealed that the ratio of \(\hbox {EtOH}\hbox {/}\hbox {H}_{2}\hbox {O}= 10\hbox {/}25\) and calcination at \(400{^{\circ }}\hbox {C}\) for 2–4 h are favourable for preparing \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials and they exhibited the best electrochemical property. The novel morphology and high specific surface area are the main factors that contribute to high electrochemical performance of \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials during the charge–discharge processes. It turns out that \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials with rough surface is an ideal material for supercapacitor electrode in the present work.     

Structural,dielectric and piezoelectric study of Ca-, Zr-modified $$\hbox {BaTiO}_{3}$$ lead-free ceramics

We prepared a lead-free ceramic (\(\hbox {Ba}_{0.85}\hbox {Ca}_{0.15})(\hbox {Ti}_{1-x}\hbox {Zr}_{x})\hbox {O}_{3}\) (BCTZ) using the conventional mixed oxide technique. The samples were prepared by an ordinary mixing and sintering technique. In this study we investigated how small amounts of \(\hbox {Zr}^{4+}\) can affect the crystal structure and microstructure as well as dielectric and piezoelectric properties of \(\hbox {BaTiO}_{3}\). X-ray diffraction analysis results indicate that no secondary phase is formed in any of the BCTZ powders for \(0 \le x \le 0.1\), suggesting that \(\hbox {Zr}^{4+}\) diffuses into \(\hbox {BaTiO}_{3}\) lattices to form a solid solution. Scanning electron microscopy micrographs revealed that the average grain size gradually increased with \(\hbox {Zr}^{4+}\) content from 9.5 \(\upmu \!\hbox {m}\) for \(x = 0.02\) to 13.5 \(\upmu \!\hbox {m}\) for \(x = 0.1\); Curie temperature decreased due to the small tetragonality caused by \(\hbox {Zr}^{4+}\) addition. Owing to the polymorphic phase transition from orthorhombic to tetragonal phase around room temperature, it was found that the composition \(x = 0.09\) showed improved electrical properties and reached preferred values of \(d_{33} = 148\) pC \(\hbox {N}^{-1}\) and \(K_{\mathrm{p}} = 27\%\).     

Microwave hydrothermal synthesis and upconversion luminescence properties of $$\hbox {Yb}^{3+}$$/$$\hbox {Tm}^{3+}$$Tm3+ co-doped $$\hbox {NaY}(\hbox {MoO}_{4})_{2}$$NaY(MoO4)2 phosphor

Tetragonal \(\text {NaY}(\text {MoO}_{4})_{2}\) (NYM) phosphors co-doped with \(\hbox {Yb}^{3+}\) and \(\hbox {Tm}^{3+}\) ions were synthesized through microwave hydrothermal method followed by calcining treatment. Powder X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy and photoluminescence spectra were used to characterize the properties of as-prepared samples. The results show that \(\hbox {Yb}^{3+}\)/\(\hbox {Tm}^{3+}\) co-doped NYM displayed bright blue emission near 472 and 476 nm (\(^{1}\hbox {G}_{4}\rightarrow {}^{3}\hbox {H}_{6}\) transition), strong near-infrared upconversion (UC) emission around 795 nm (\(^{3}\hbox {H}_{4}\rightarrow {}^{3}\hbox {H}_{6}\) transition). The optimum doping concentrations of \(\hbox {Yb}^{3+}\) and \(\hbox {Tm}^{3+}\) for the most intense UC luminescence were obtained, and the related UC mechanism of \(\hbox {Yb}^{3+}\)/\(\hbox {Tm}^{3+}\) co-doped NYM depending on pump power was studied in detail.     

Elastic and thermodynamic properties of zirconium- and hafnium-doped $$\hbox {Rh}_{3}\hbox {V}$$ intermetallic compounds: potential aerospace material

Structural, electronic, mechanical and thermodynamic properties of \(\hbox {Rh}_{3}\hbox {Zr}_{x}\hbox {V}_{1-x}\) and \(\hbox {Rh}_{3}\hbox {Hf}_{x}\hbox {V}_{1-x}\) (\(x = 0\), 0.125, 0.25, 0.75, 0.875 and 1) combinations are investigated by means of first-principles calculations based on the density functional theory within the generalized gradient approximation. Here, \(\hbox {Rh}_{3}\hbox {V}\) is chosen as the parent binary compound and the doping elements are zirconium and hafnium with the above-mentioned concentrations. The calculated lattice parameters and elastic modulus of binary \(\hbox {Rh}_{3}\hbox {Hf}\), \(\hbox {Rh}_{3}\hbox {V}\) and \(\hbox {Rh}_{3}\hbox {Zr}\) are in good agreement with the available experimental and other theoretical results. In this study, the following ternary materials viz., \(\hbox {Rh}_{3}\hbox {Zr}_{0.75}\hbox {V}_{0.25}\), \(\hbox {Rh}_{3}\hbox {Hf}_{0.25}\hbox {V}_{0.75}\) and \(\hbox {Rh}_{3}\hbox {Hf}_{0.75}\hbox {V}_{0.25}\) are found to be brittle/more brittle than the parent binary compound \(\hbox {Rh}_{3}\hbox {V}\), whereas the other ternary combinations, namely \(\hbox {Rh}_{3}\hbox {Zr}_{0.125}\hbox {V}_{0.875}\), \(\hbox {Rh}_{3}\hbox {Zr}_{0.25}\hbox {V}_{0.75}\), \(\hbox {Rh}_{3}\hbox {Zr}_{0.875}\hbox {V}_{0.125}\), \(\hbox {Rh}_{3}\hbox {Hf}_{0.125}\hbox {V}_{0.875}\) and \(\hbox {Rh}_{3}\hbox {Hf}_{0.875}\hbox {V}_{0.125}\) are found to be more ductile than \(\hbox {Rh}_{3}\hbox {V}\). The more brittle ternary combination, namely \(\hbox {Rh}_{3}\hbox {Hf}_{0.75}\hbox {V}_{0.25}\) (\(B = 229.32\,\hbox {GPa}\)) has the maximum Young’s modulus, shear modulus and hardness values; whereas the more ductile ternary \(\hbox {Rh}_{3}\hbox {Zr}_{0.25}\hbox {V}_{0.75}\) combination (\(B = 243.54\,\hbox {GPa}\)) is found to have the least values of Young’s modulus, shear modulus and hardness. The band structure, density of states histograms and charge density plots are drawn and discussed. Computed Debye temperature (\(\theta _{\mathrm{D}}\)), Grüneisen parameter (\(\zeta \)) and melting temperature (\(T_{\mathrm{m}})\) of the parent binary compound \(\hbox {Rh}_{3}\hbox {V}\), the more brittle \(\hbox {Rh}_{3}\hbox {Hf}_{0.75}\hbox {V}_{0.25}\) combination and the more ductile \(\hbox {Rh}_{3}\hbox {Zr}_{0.25}\hbox {V}_{0.75}\) combination are given by (895 K, 1.3491, 2788 K), (790 K, 1.2701, 2736 K) and (698 K, 1.7972, 2529 K), respectively.     

Thermo-transport properties of Zn-substituted layered Li-nickel oxide, $$\hbox {LiNiO}_{2}$$

The layered Li-TM-\(\hbox {O}_{2}\) materials have been investigated extensively due to their application as cathodes in Li batteries. The electrical properties of these oxides can be tuned or controlled either by non-stoichiometry or substitution. Hence the thermo-transport properties of Zn-substituted \(\hbox {LiNi}_{1-x}\hbox {Zn}_{x}\hbox {O}_{2}\) for \(0 \le x \le 0.16\) have been investigated in the temperature range of 300–900 K for potential application as a high-temperature thermoelectric material. For \(x < 0.08\), the compounds were of single phase belonging to the space group R-3mH while for \(x > 0.08\) an additional minority phase, ZnO forms together with the main layered phase. All the compounds exhibit a semiconducting behaviour with electrical resistivity, varying in the range of  \(\sim 10^{-4}\) to \(10^{-2}\,\,\Omega \hbox {m}\) between 300 and 900 K. The electrical resistivity is found to increase with increasing Zn-substitution predominantly due to a decrease in the charge carrier hole mobility. The activation energy remains constant, \(\sim \)10  meV, with Zn-substitution. The Seebeck coefficient of the compounds is found to decrease with increasing temperature and increase with increasing Zn-substitution. The Seebeck coefficient decreases from \(\sim \)95 to \(35\ \upmu \hbox {V K}^{-1}\) and the corresponding power factor is \(\sim \)12\(\ \upmu \hbox {W m}^{-1}\ {\hbox {K}}^{-2}\) for the \(x = 0.16\) compound.     

Study of $$\upbeta $$-phase development in spin-coated PVDF thick films

A study was conducted to ascertain the effect of variation in spin speed and baking temperature on \(\upbeta \)-phase content in the spin-coated poly(vinylidene fluoride) (PVDF) thick films (\({\sim }4{-}25\,\upmu \hbox {m}\)). Development of \(\upbeta \)-phase is dependent on film stretching and crystallization temperature. Therefore, to study the development of \(\upbeta \)-phase in films, stretching is achieved by spinning and crystallization temperature is adjusted by means of baking. PVDF films are characterized using Fourier transform infrared spectroscopy, X-ray diffraction, differential scanning calorimetry, and scanning electron microscopy. It is observed that crystallization temperature lower than \(60^{\circ }\hbox {C}\) and increase in spin speed increases the \(\upbeta \)-phase content in PVDF films. Crystallization temperature above \(60^{\circ }\hbox {C}\) reduces \(\upbeta \)-phase content and increases \(\upalpha \)-phase content. It was also observed that viscosity of the PVDF solution affects the \(\upbeta \)-phase development in films at a particular spin speed.     

Synthesis and up-conversion emissions of $$\hbox {Yb}^{3+}{/}\hbox {Er}^{3+}$$, $$\hbox {Yb}^{3+}{/}\hbox {Tm}^{3+}$$Yb3+/Tm3+ and $$\hbox {Yb}^{3+}{/}\hbox {Tm}^{3+}{/}\hbox {Gd}^{3+}$$Yb3+/Tm3+/Gd3+ co-doped $$\hbox {KLu}_{2}\hbox {F}_{7}$$KLu2F7

\(\hbox {Yb}^{3+}/\hbox {Er}^{3+}\), \(\hbox {Yb}^{3+}/\hbox {Tm}^{3+}\), or \(\hbox {Yb}^{3+}/\hbox {Tm}^{3+}/\hbox {Gd}^{3+}\) co-doped \(\hbox {KLu}_{2}\hbox {F}_{7}\) up-conversion (UC) materials were synthesized through a hydrothermal method or an additive-assisted hydrothermal method. The X-ray diffraction (XRD) results suggested that the materials crystallized in orthorhombic phase, yet, the potassium citrate (CitK) introduction affected immensely the crystalline purity of final material. The field emission scanning electron microscopy (FE-SEM) results suggested that the additive adding had effects on size and morphology of the material, which affected the UC emissions further. Green/red UC emissions of \(\hbox {Er}^{3+}\), UV/blue/IR UC emissions of \(\hbox {Tm}^{3+}\), and UV UC emissions of \(\hbox {Gd}^{3+}\) were observed in the orthorhombic phase of \(\hbox {KLu}_{2}\hbox {F}_{7}\) materials. The excitation power-dependent UC emissions illustrated that the UC emission intensity initially increased, then decreased with the increase in excitation power. At the same time, the variation rates of different transitions in \(\hbox {Er}^{3+}\) or \(\hbox {Tm}^{3+}\) are also different. In addition, the \(\hbox {Er}^{3+}\) or \(\hbox {Tm}^{3+}\) concentration-dependent UC emission results suggested that the optimal doping concentration of \(\hbox {Er}^{3+}\) is 2 mol% and \(\hbox {Tm}^{3+}\) is 0.5 mol% with the \(\hbox {Yb}^{3+}\) concentration fixed as 20 mol%. The experimental results suggest that the orthorhombic phase of \(\hbox {KLu}_{2}\hbox {F}_{7}\) should be a good host lattice for UC emitters.     

Structural and physical properties of $$\hbox {Sm}^{3+}$$ doped magnesium zinc sulfophosphate glass

Samarium (\(\hbox {Sm}^{3+})\) doped magnesium zinc sulfophosphate glass system of composition (60–\(x)\hbox {P}_{2}\hbox {O}_{5}\)–20MgO–20ZnSO\(_{4}\)–\(x\hbox {Sm}_{2}\hbox {O}_{3}\) (\(x =\) 0.0, 0.5, 1.0, 1.5 and 2.0 mol%) were synthesized using melt-quenching technique. The structure and physical properties of prepared glass samples were characterized. The X-ray diffraction pattern verified their amorphous nature. The physical properties such as density, refractive index, molar volume, rare earth ion concentration, etc. were calculated. The decrease in the optical bandgap energy with increasing \(\hbox {Sm}_{2}\hbox {O}_{3}\) contents was attributed to the alteration in the glass network structures. Fourier transformed infrared spectra and Raman analyses manifested the depolymerization of \(\hbox {ZnSO}_{4}\) in the phosphate host matrix. The present findings may be beneficial for the advancement of functional glasses.