Water absorption behavior of PALF/GF hybrid polyester composites

The water absorption characteristics of pineapple leaf fiber (PALF)/glass fiber (GF) hybrid polyester(PER) composites, and chemically modified PALF/polyester composites were evaluated by immersion in distilled water at 28, 60, and 90°C. The diffusion properties of the intimately mixed (IM) and the layered hybrid composite GPG (Glass skin and PALF core) of different PALF/GF ratio at the three temperatures were compared in order to identify the environmental ageing mechanism at different temperatures. The effect of temperature on the kinetics and thermodynamics of diffusion were also examined. The water uptake of both IM and GPG hybrid composites was decreased with increase in glass fiber content; the lowest water uptake was observed for 0.46 V_f GF hybrid composite. Among the chemically modified composites, vinyl tri 2‐methoxy ethoxy silane treated composites showed the lowest water uptake. Finally, parameters like diffusion, sorption, and permeability coefficients were determined. It was observed that equilibrium water uptake is dependent on the nature of the composite and temperature. Experimental results were also compared with theoretical predictions. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Mechanical properties of pineapple leaf fiber-reinforced polyester composites

Pineapple leaf fiber (PALF) which is rich in cellulose, relatively inexpensive, and abundantly available has the potential for polymer reinforcement. The present study investigated the tensile, flexural, and impact behavior of PALF-reinforced polyester composites as a function of fiber loading, fiber length, and fiber surface modification. The tensile strength and Young's modulus of the composites were found to increase with fiber content in accordance with the rule of mixtures. The elongation at break of the composites exhibits an increase by the introduction of fiber. The mechanical properties are optimum at a fiber length of 30 mm. The flexural stiffness and flexural strength of the composites with a 30% fiber weight fraction are 2.76 GPa and 80.2 MPa, respectively. The specific flexural stiffness of the composite is about 2.3 times greater than that of neat polyester resin. The work of fracture (impact strength) of the composite with 30% fiber content was found to be 24 kJ m⁻². Significant improvement in the tensile strength was observed for composites with silane A172-treated fibers. Scanning electron microscopic studies were carried out to understand the fiber-matrix adhesion, fiber breakage, and failure topography. The PALF polyester composites possess superior mechanical properties compared to other cellulose-based natural fiber composites. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1739–1748, 1997     

Effect of hybridization and chemical modification on the water‐absorption behavior of banana fiber–reinforced polyester composites

The water sorption characteristics of banana fiber–reinforced polyester composites were studied by immersion in distilled water at 28, 50, 70, and 90°C. The effect of hybridization with glass fiber and the chemical modification of the fiber on the water absorption properties of the prepared composites were also evaluated. In the case of hybrid composites, water uptake decreased with increase of glass fiber content. In the case of chemically modified fiber composites, water uptake was found to be dependent on the chemical treatment done on the fiber surface. Weight change profiles of the composites at higher temperature indicated that the diffusion is close to Fickian. The water absorption showed a multistage mechanism in all cases at lower temperatures. Chemical modification was found to affect the water uptake of the composite. Among the treated composites the lowest water uptake was observed for composites treated with silane A1100. Finally, parameters like diffusion, sorption, and permeability coefficients were determined. It was observed that equilibrium water uptake is dependent on the nature of the composite and temperature. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3856–3865, 2004     

Influence of organically modified nanoclay on the performance of pineapple leaf fiber‐reinforced polypropylene nanocomposites

Polypropylene/Pine apple leaf fiber (PP/PALF)‐reinforced nanocomposites were fabricated using melt blending technique in a twin‐screw extruder (Haake Rheocord 9000). Variation in mechanical properties, crystallization behavior, water absorption, and thermal stability with the addition of nanoclay in PP/PALF composites were investigated. It was observed that the tensile, flexural, and impact properties of PP increase with the increase in fiber loading from 10 to 30 wt %. Composites prepared using 30 wt % PALF and 5 wt % MA‐g‐PP exhibited optimum mechanical performance with an increase in tensile strength to 31%, flexural strength to 45% when compared with virgin PP. Addition of nanoclay results in a further increase in tensile and flexural strength of PP/PALF composites to 20 and 24.3%, which shows intercalated morphology. However, addition of nanoclay does not show any substantial increase in impact strength when compared with PP/PALF composites. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), confirming a strong influence between the fiber/nanoclay and MA‐g‐PP. Differential scanning calorimetry, thermogravimetric analysis thermograms also showed improved thermal properties when compared with the virgin matrix. TEM micrographs also showed few layers of agglomerated clay galleries along with mixed nanomorphology in the nanocomposites. Wide angle X‐ray diffraction studies indicated an increase in d‐spacing from 22.4 Å in Cloisite 20A to 40.1 Å in PP/PALF nanocomposite because of improved intercalated morphology. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Dynamic mechanical analysis of pineapple leaf/glass hybrid fiber reinforced polyester composites

The dynamic mechanical properties of randomly oriented intimately mixed hybrid composites based on pineapple leaf fibers (PALF) and glass fibers (GF) in unsaturated polyester (PER) matrix were investigated. The PALFs have high‐specific strength and improve the mechanical properties of the PER matrix. In this study, the volume ratio of the two fibers was varied by incorporating small amounts of GF such as PALF/GF, 90/10, 80/20, 70/30, and 50/50, keeping the total fiber loading constant at 40 wt%. The dynamic modulus of the compositeswas found to increase on GF addition. The intimately mixed (IM) hybrid composites with PALF/GF, 80/20 (0.2 V_f GF) showed highest E′ values and least damping. Interestingly, the impact strength of the composites was minimum at this volume ratio. The composites with 0.46 V_f GF or PALF/GF (50/50) showed maximum damping behavior and highest impact strength. The results were compared with hybrid composites of different layering patterns such as GPG (GF skin and PALF core) and PGP (PALF skin and GF core). IM and GPG hybrid composites are found more effective than PGP. The activation energy values for the relaxation processes in different composites were calculated. The overall results showed that hybridization with GF enhanced the performance properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Pineapple leaf fiber reinforced thermoplastic composites: Effects of fiber length and fiber content on their characteristics

Pineapple leaf fiber (PALF) was used as a reinforcement in polyolefins. Polypropylene (PP) and low‐density polyethylene (LDPE) composites with different fiber lengths (long and short fibers) and fiber contents (0–25%) were prepared and characterized. The results showed that the tensile strength of the composites increased when the PALF contents were increased. It was observed that the composites containing long fiber PALF were stronger than the short fiber composites as determined by greater tensile strength. An SEM study on the tensile fractured surface confirmed the homogeneous dispersion of the long fibers in the polymer matrixes better than dispersion of the short fibers. The unidirectional arrangement of the long fibers provided good interfacial bonding between the PALF and polymer which was a crucial factor in achieving high strength composites. Reduction in crystallinity of the composites, as evident from XRD and DSC studies suggested that the reinforcing effect of PALF played an important role in enhancing their mechanical strength. From the rule of mixtures, the stress efficiency factors of the composite strength could be calculated. The stress efficiency factors of LDPE were greater than those of PP. This would possibly explain why the high modulus fiber (PALF) had better load transfers to the ductile matrix of LDPE than the brittle matrix of PP. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

黄麻纤维增强不饱和聚酯树脂初步研究

以油酸为偶联剂,将氢氧化钠-油酸处理后的黄麻纤维布作为填充材料制备了不饱和聚酯复合材料,并对氢氧化钠处理黄麻纤维的适宜浓度、复合材料的拉伸强度、冲击强度、吸水率进行了研究测试。结果表明:氢氧化钠的适宜浓度为20%,黄麻纤维增强不饱和聚酯树脂的冲击强度及拉伸强度最大值分别为12.75 kJ/m2和33.05 MPa,复合材料的最大吸水率为4.07%。经油酸处理的黄麻纤维可有效提高不饱和聚酯复合材料的性能。     

ACETYLATED PLANT-FIBER-REINFORCED POLYESTER COMPOSITES: A STUDY OF MECHANICAL,HYGROTHERMAL, AND AGING CHARACTERISTICS

The potential of acetylation of plant fibers to improve the properties of composites was studied. The chemical modification of oil palm empty fruit bunch (EFB), coconut fiber (Coir), oil palm frond (OPF), jute, and flax using noncatalyzed acetic anhydride were investigated. Proof of acetylation was indicated by the increase in weight percent gain (WPG). Acetylation at a reaction temperature of 120°C had resulted in the reduction in the tensile properties (stress, modulus, and elongation at break) of EFB and Coir composites. However, at 100°C, the acetylated samples exhibited improved properties. The mechanical properties of acetylated EFB- and Coir-fiber-reinforced polyester composites was evaluated at different fiber loadings. The tensile strength and modulus were improved, but elongation at break was slightly reduced upon acetylation, particularly at high fiber loading. Impact properties were moderately increased for those composites with fiber loadings up to 45%. Acetylation exhibited a low moisture absorption, comparable with glass-fiber composites. Acetylated EFB and Coir composites showed superior retention of tensile and impact properties after aging in water up to 12 months.     

The influence of fiber surface modification on the mechanical properties of coir‐polyester composites

Coir, an important lignocellulosic fiber, can be incorporated in polymers like unsaturated polyester in different ways for achieving desired properties and texture. But its high level of moisture absorption, poor wettability and insufficient adhesion between untreated fiber and the polymer matrix lead to debonding with age. In order to improve the above qualities, adequate surface modification is required. In our present work, fiber surface modification was effected through dewaxing, alkali (5%) treatment, aqueous graft copolymerization of methyl methacrylate (MMA) onto 5% alkali treated coir for different extents using CuSO₄ – NaIO₄ combination as an initiator system and cyanoexhylation with a view to improve the mechanical performance of coir‐polyester composites. Mechanical properties like tensile strength (PS), flexural strength (ES) and impact strength (IS) of the composites as a function of fiber loading and fiber surface modification have been evaluated. Composites containing z5 wt% of fiber (untreated) improved tensile and flexural strength by 30% and 27% respectively in comparison to neat polyester. The work of fracture (impact strength) of the composite with 25 wt% fiber content was found to be 967 J/m. The elongation at break of the composites exhibits an increase with the introduction of fiber, All types of surface modification result In improved mechanical properties of the composites. Significant improvement in mechanical strength was also observed for composites prepared from 5% PMMA grafted fiber.     

Novel low‐cost jute–polyester composites. III. Weathering and thermal behavior

Jute–polyester composites were fabricated with untreated (control) and bleached slivers with 60% loading of fiber by weight and were designated as JPH(C) and JPH(B), respectively. Both types of composite specimens were subjected to water absorption and outdoor weathering tests to assess their relative performance under environmental conditions. While both composites showed low water absorption, JPH(B) showed lesser water absorption (8.48%) than did JPH(C) (12.25%). The mechanical properties like tensile and flexural strengths were measured for both the weathered and unweathered specimens and compared. The tensile strength of JPH(C) and JPH(B) decreased while the tensile modulus increased after weathering. The flexural strength, moduli, and ILSS of the weathered specimens were less than those of the unweathered ones. The nature of the fiber–matrix adhesion could be established from these results. The cause of every observation is explained. Thermal analyses (TG/DTG and DSC) of the composite specimens were also done. The overall thermal stability of JPH(C) was found to be better than that of JPH(B). © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1671–1679, 2000     

Mechanical properties and water absorption of fiber‐reinforced polypropylene composites prepared by bagasse and beech fiber

The present study investigates the tensile, flexural, notched Izod impact, and water absorption properties of bagasse and beech reinforced polypropylene (PP) composites as a function of fiber content. The surface of fibers was modified through the use of maleated polypropylene (MAPP) coupling agent. From this study, it was found that mechanical properties increase with an increase in fiber loading in both cases. However, the addition of wood fibers resulted in a decrease in impact strength of the composites. The water absorption property at varying fiber loading was evaluated and found maximum for the BA/PP composites. The weight gains for all specimens were less than 7%. In general, the results showed the usefulness of bagasse fiber as a good alternative and reinforcing agent for composite. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of alkalization on tensile,impact, and fatigue properties of hemp fiber composites

The effects of alkalization surface treatment on hemp fiber properties and the properties of hemp fiber–reinforced polyester composites have been studied. Hemp fibers were exposed to 1, 5, and 10% sodium hydroxide (NaOH) solutions. The tensile properties and interfacial shear strength of all alkalized fibers were found to lie within the range of nonalkalized fibers. Laminates were made of alkalized fibers with unsaturated polyester resin, using hand lay‐up and compression moulding. Alkalization of fibers at low concentrations of 1 and 5% resulted in improvements in tensile and fatigue properties of composites made from these fibers, but no such improvements were observed for 10% alkalized fiber composites. The improvements were attributed to improvement in fiber/matrix bonding after this treatment, which was also confirmed by scanning electron microscopy images. No improvement in impact damage tolerance was observed for any of these three alkalized fiber composites. Immersion in distilled water reduced water absorption compared with nonalkalized fiber composites; however, the tensile properties in water were similar to those for nonalkalized fiber composites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Hybrid composites from coir fibers reinforced with woven glass fabrics: Physical and mechanical evaluation

Sandwich composites based on coir fiber nonwoven mats as core material were manufactured by Vacuum Assisted Resin Transfer Molding technique. Mechanical and physical properties of produced coir/polyester and coir‐glass/polyester composites were assessed. Samples were evaluated according to their reinforcement contents, resin contents, areal density, and thickness. Tests on physical properties revealed that coir‐glass/polyester sandwich structure has the lowest values of thickness swelling, water absorption and moisture contents compared with coir/polyester composite. Mechanical tests such as tensile strength, open‐hole tensile strength, and flexural strength were also performed on all samples. Coir‐glass/polyester sandwich structure showed significant increase in tensile strength of 70 MPa compared with 8 MPa of coir/polyester composite. Introducing two skins of fiber glass woven roving to coir/polyester increased its flexural strength from 31.8 to 131.8 MPa for coir‐glass/polyester. POLYM. COMPOS., 38:2212–2220, 2017. © 2015 Society of Plastics Engineers     

Bamboo fiber reinforced thermosetting resin composites: Effect of graft copolymerization of fiber with methacrylamide

Epoxy and polyester resins have been reinforced with methacrylamide (MAA) treated bamboo strip matting to develop bamboo fiber reinforced plastic composites. Bamboo mats were graft copolymerized with 1, 3, and 5% solution of MAA. The mechanical (tensile strength, elastic modulus, flexural strength, and flexural modulus), thermal, and water absorption properties of the composites were determined. One percent treatment of bamboo with MAA gave optimum results with epoxy resin. The mechanical properties were improved. TGA results reveal that the degradation temperature of the composite has improved after grafting. The weight loss of 1% MAA treated bamboo–epoxy composite reached a value of 95.132% at 795°C compared to 97.655% at 685°C of untreated bamboo–epoxy composite. Water absorption in the composites was studied by long term immersion and 2 h boiling in distilled water. The process of water absorption indicates Fickian mode of diffusion. MAA treatment results in reduced water uptake. There was improvement in the properties of pretreated bamboo‐polyester matrix composite as well. Three percent treatment of bamboo with MAA gave optimum results with polyester resin. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Utilization of lignocellulosic fibers in molded polyester composites

Using rice straw, bagasse, and cotton stalk fibers as reinforcing fillers in polyester composite was studied. The effects of fiber loading and fiber size on the modulus of rupture (MOR), modulus of elasticity (MOE), tensile strength, water absorption, and thickness swelling were investigated as well. The effect of esterification using maleic anhydride on the aforementioned properties also was studied. Ultraviolet light resistance and thermal behavior of the produced composites were also investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 653–660, 2003     

Performance of pineapple leaf fiber–natural rubber composites: The effect of fiber surface treatments

Composites of natural rubber (NR) and short pineapple leaf fiber (PALF) were prepared on a laboratory two‐roll mill. The influences of untreated fiber content and orientation on the processing and mechanical properties of the composites were investigated. The dependence of extent of orientation on fiber concentration was also established. Sodium hydroxide (NaOH) solutions (1, 3, 5, and 7% w/v) and benzoyl peroxide (BPO) (1, 3, and 5 wt % of fiber) were used to treat the surfaces of PALFs. FTIR and scanning electron microscope (SEM) observations were made of the treatments in terms of chemical composition and surface structure. The tensile strength and elongation at break of the composites were later studied. The fiber–matrix adhesion was also investigated using SEM technique. It was found that all surface modifications enhanced adhesion and tensile properties. The treatments with 5% NaOH and 1% BPO provided the best improvement of composite strength (28 and 57% respectively) when compared with that of untreated fiber. The PALF‐NR composites also exhibited better resistance to aging than its gum vulcanizate, especially when combined with the treated fibers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1974–1984, 2006     

A study of the mechanical properties of randomly oriented short banana and sisal hybrid fiber reinforced polyester composites

The mechanical performance of short randomly oriented banana and sisal hybrid fiber reinforced polyester composites was investigated with reference to the relative volume fraction of the two fibers at a constant total fiber loading of 0.40 volume fraction (V_f), keeping banana as the skin material and sisal as the core material. A positive hybrid effect is observed in the flexural strength and flexural modulus of the hybrid composites. The tensile strength of the composites showed a positive hybrid effect when the relative volume fraction of the two fibers was varied, and maximum tensile strength was found to be in the hybrid composite having a ratio of banana and sisal 4 : 1. The impact strength of the composites was increased with increasing volume fraction of sisal. However, a negative hybrid effect is observed when the impact strength of the composites is considered. Keeping the relative volume fraction of the two fibers constant, that is, banana : sisal = 0.32 : 0.08 (i.e., 4 : 1), the fiber loading was optimized and different layering patterns were investigated. The impact strength of the composites was increased with fiber loading. Tensile and flexural properties were found to be better at 0.40 V_f. In the case of different layering patterns, the highest flexural strength was observed for the bilayer composites. Compared to other composites, the tensile properties were slightly higher for the composite having banana as the skin material and sisal as the core material. Scanning electron micrographs of the tensile and impact fracture surfaces of the hybrid composites having volume fraction 0.20 and 0.40 V_f were studied. The experimental tensile strength and tensile modulus of hybrid composites were compared with those of theoretical predictions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1699–1709, 2005     

Polyester composites of short pineapple fiber and glass fiber: Tensile and impact properties

The tensile and impact performance of intimately mixed (IM) hybrid composites based on glass fiber (GF) and pineapple leaf fiber (PALF) was investigated. The composite was fabricated at constant volume fraction of fiber 0.3 V_f (fiber 0.3 and matrix 0.7). Keeping the volume fraction of matrix a constant (0.7 V_f), we have varied the PALF/GF ratio from 0 to 1. Incorporation of 0.1 volume fraction of GF increases the tensile strength of the hybrid composite by about 28%. The tensile strength showed a further increase when the volume fraction is changed to 0.7 and 0.9 V_f of GF. Intimately mixed hybrid composites exhibited higher impact strength than the individual fiber composites; the composite of PALF/GF ratio 70:30 showed maximum impact strength of 1203 J/m. A positive hybrid effect is observed for impact properties. Scanning electron micrographs of the fractured surfaces were examined to understand the fiber‐matrix adhesion. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Evaluation of the mechanical properties of sisal–polyester composites as a function of the polyester matrix formulation

In this work a comparative study on the impact and tensile properties of polyester/sisal fiber reinforced composites was undertaken. The polyester matrix was used bare and modified with: (1) a silane coupling agent; (2) a flame retardant system; and (3) a blend of the silane agent and the flame retardant system. The experimental results show that the flame retardant acts as a particulate reinforcement to the polyester matrix and the silane coupling agent acts as a plasticizer. The simultaneous addition of these two compounds to the polyester resin tended to decrease the performance of the composites. The results obtained show that strength or toughness could be tailored, and although none of the composites manufactured with the modified polyester matrices showed a significant improvement on the fiber–matrix interface strength, a better compromise between impact and tensile properties was obtained with the silane modified matrix. The critical fiber volume fraction was also evaluated and shown to be less than 10% for the sisal–polyester composite investigated here. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1209–1217, 2004     

Characterization of Short Glass Fiber–Reinforced Castor Oil–Based Polyurethane Polystyrene Interpenetrating Networks

ABSTRACT

Chopped strand glass fiber–reinforced particle-filled castor oil–based polyurethane polystyrene composites with varying weight fractions of glass fibers were investigated for morphology, tensile strength, and absorption of various chemicals. The short glass fiber fraction was varied from 1% to 16% (by wt.) of the total composite system. The tensile strength of these composites was much higher than that of unfilled IPNs for the same concentration of polystyrene. The tensile strength of the IPN composites increases with the increase in fiber content up to a fiber percentage of 9%. After that, there is a sharp decline in tensile modulus as well as elongation at break. The chemical absorption showed an increase with increasing glass fiber content.