Ultrasonic improvement of the compatibility and rheological behavior of high‐density polyethylene/polystyrene blends

The effects of ultrasonic oscillations on the rheological behavior, mechanical properties, and morphology of high‐density polyethylene (HDPE)/polystyrene (PS) blends were studied. The experimental results show that the die pressure and apparent viscosity of HDPE/PS blends are remarkably reduced in the presence of ultrasonic oscillations and that mechanical properties of the blends are improved. The particle size of the dispersed phase in HDPE/PS blends becomes smaller, its distribution becomes narrower, and the interfacial interaction of the blends becomes stronger if the blends are extruded in the presence of ultrasonic oscillations. Ultraviolet spectra and Soxhlet extraction results show the formation of a polyethylene‐PS copolymer during extrusion in the presence of ultrasonic oscillations, which improves the compatibility of HDPE/PS blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 23–32, 2002     

Modification of recycled high‐density polyethylene by low‐density and linear‐low‐density polyethylenes

The present study investigated mixed polyolefin compositions with the major component being a post‐consumer, milk bottle grade high‐density polyethylene (HDPE) for use in large‐scale injection moldings. Both rheological and mechanical properties of the developed blends are benchmarked against those shown by a currently used HDPE injection molding grade, in order to find a potential composition for its replacement. Possibility of such replacement via modification of recycled high‐density polyethylene (reHDPE) by low‐density polyethylene (LDPE) and linear‐low‐density polyethylene (LLDPE) is discussed. Overall, mechanical and rheological data showed that LDPE is a better modifier for reHDPE than LLDPE. Mechanical properties of reHDPE/LLDPE blends were lower than additive, thus demonstrating the lack of compatibility between the blend components in the solid state. Mechanical properties of reHDPE/LDPE blends were either equal to or higher than calculated from linear additivity. Capillary rheological measurements showed that values of apparent viscosity for LLDPE blends were very similar to those of the more viscous parent in the blend, whereas apparent viscosities of reHDPE/LDPE blends depended neither on concentration nor on type (viscosity) of LDPE. Further rheological and thermal studies on reHDPE/LDPE blends indicated that the blend constituents were partially miscible in the melt and cocrystallized in the solid state.     

Rheological,thermal, and morphological properties of low‐density polyethylene/ultra‐high‐molecular‐weight polyethylene and linear low‐density polyethylene/ultra‐high‐molecular‐weight polyethylene blends

The dynamic rheological behavior of low‐density polyethylene (LDPE)/ultra‐high‐molecular‐weight polyethylene (UHMWPE) blends and linear low‐density polyethylene (LLDPE)/UHMWPE blends was measured in a parallel‐plate rheometer at 180, 190, and 200°C. Analysis of the log–additivity rule, Cole–Cole plots, Han curves, and Van Gurp curves of the LDPE/UHMWPE blends indicated that the blends were miscible in the melt. In contrast, the rheological properties of LLDPE/UHMWPE showed that the miscibility of the blends was decided by the composition of LLDPE. The differential scanning calorimetry results and scanning electron microscopy photos of the LLDPE/UHMWPE blends were consistent with the rheological properties, whereas with regard to the thermal and morphological properties of LDPE/UHMWPE blends, the results reveal three endothermic peaks and phase separation, which indicated a liquid–solid phase separation in the LDPE/UHMWPE blends. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Compatibilization of low‐density polyethylene/plasticized starch blends by reactive compounds and electron beam irradiation

Blends based on various compositions of low‐density polyethylene (LDPE) and plasticized starch (PLST) were prepared by melt extrusion and molding in the form of sheets under hot press. The rheology properties during mixing were studied in terms of torque and temperature against mixing time. The structural properties of LDPE/PLST blends before and after electron beam irradiation was characterized by IR spectroscopy, tensile mechanical testing, and scanning electron microscopy (SEM). The torque‐time curves during the mixing process showed that the values of torque in the first region of mixing for pure LDPE or LDPE/PLST blends are higher in the presence of the compatibilizer PEMA than that in the presence of EVA. In addition, the stability of mixing was attained after a short time in the presence of PEMA. The IR spectroscopy suggests that the compatibilization by EVA and PEMA compounds proceeds through the formation of hydrogen bonding during mixing and this compatibility was improved after electron beam irradiation. The stress–strain curves of pure LDPE and its blends with PLST showed the behavior of tough polymers with yielding properties. The SEM micrographs of the fracture surfaces give supports to the effect of EVA and PEMA as compatibilizers and the effect of electron beam irradiation. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Thermal and mechanical properties of linear low‐density polyethylene/low‐density polyethylene/wax ternary blends

The thermal and mechanical properties of uncrosslinked three‐component blends of linear low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and a hard, paraffinic Fischer–Tropsch wax were investigated. A decrease in the total crystallinity with an increase in both LDPE and wax contents was observed. It was also observed that experimental enthalpy values of LLDPE in the blends were generally higher than the theoretically expected values, whereas in the case of LDPE the theoretically expected values were higher than the experimental values. In the presence of higher wax content there was a good correlation between experimental and theoretically expected enthalpy values. The DSC results showed changes in peak temperature of melting, as well as peak width, with changing blend composition. Most of these changes are explained in terms of the preferred cocrystallization of wax with LLDPE. Young's modulus, yield stress, and stress at break decreased with increasing LDPE content, whereas elongation at yield increased. This is in line with the decreasing crystallinity and increasing amorphous content expected with increasing LDPE content. Deviations from this behavior for samples containing 10% wax and relatively low LDPE contents are explained in terms of lower tie chain fractions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1748–1755, 2005     

Ultrasonic oscillations effect on rheological and processing properties of metallocene‐catalyzed linear low density polyethylene

The effects of ultrasonic oscillations and die materials on die pressure, productivity of extrusion, melt viscosity of metallocene‐catalyzed linear low density polyethylene (mLLDPE), as well as their mechanism were studied in a special ultrasonic oscillations extrusion system developed in our lab. Die materials used in our experiment included steel, brass, and polytetrafluoroethylene (PTFE)_. The experimental results showed that ultrasonic oscillations as well as die materials have great influence on the rheological and processing behavior of mLLDPE. Ultrasonic oscillations can greatly increase the productivity of mLLDPE melt extruded through different dies, and can decrease the die pressure and the melt viscosity of mLLDPE. Compared with steel or brass die, mLLDPE melt extruded through PTFE die is more sensitive to ultrasonic oscillations. A possible mechanism for the improved processability of mLLDPE is proposed in this article. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1873–1878, 2003     

Influence of branching characteristics on thermal and mechanical properties of Ziegler–Natta and metallocene hexene linear low‐density polyethylene blends with low‐density polyethylene

The effect of the branch content (BC) and composition distribution (CD) of linear low‐density polyethylene (LLDPE) on the thermal and mechanical properties of its blends with LDPE were studied. All blends and pure resins were conditioned in a Haake PolyDrive blender at 190°C and in the presence of adequate amounts of antioxidant. Two metallocene LLDPEs (m‐LLDPE) and one Ziegler–Natta (ZN) hexene LLDPE were melt blended with the same LDPE. The effect of the BC was investigated by blending two hexene m‐LLDPEs of similar weight‐average molecular weights and molecular weight distributions but different BCs with the same LDPE. The effect of the CD was studied by using a ZN and an m‐LLDPE with similar weight‐average molecular weights, BCs, and comonomer type. Low‐BC m‐LLDPE blends showed separate crystallization whereas cocrystallization was observed in the high‐BC m‐LLDPE‐rich blends. However, ZN‐LLDPE/LDPE blends showed separate crystallization together with a third population of cocrystals. The influence of the crystallization behavior was reflected in the mechanical properties. The BC influenced the modulus, ultimate tensile strength, and toughness. The addition of a small amount of LDPE to a low‐BC m‐LLDPE resulted in a major improvement in the toughness, whereas the results for the high‐BC pair followed the additivity rule. ZN‐LLDPE blends with LDPE blends were found to be more compatible and exhibited superior mechanical properties compared to m‐LLDPE counterparts with the same weight‐average molecular weight and BC. All mechanical properties of ZN‐LLDPE blends follow the linear rule of mixtures. However, the CD had a stronger influence on the mechanical properties in comparison to the BC. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2488–2498, 2005     

Effects of high‐energy electron beam on low‐density polyethylene materials containing EVA

A series of low‐density polyethylene (LDPE) blends with different amounts of ethylene–vinyl–acetate (EVA) was prepared and irradiated with 10 MeV electron beam in the range of 0–250 kGy at room temperature in air. EVA was used as a compatibilizer and softener in four different amounts: 5, 10, 20, and 30 wt %, based on polyethylene (PE). The crosslinking of the samples was studied on the basis of gel‐content measurements as well as some thermal and mechanical properties of the specimens. The results indicated that the LDPE and LDPE–EVA blends could be crosslinked by a high‐energy electron beam, of which their thermal and mechanical properties changed effectively, however, because of EVA content of the polymer; the blends were more sensitive to lower doses of radiation. These studies were carried out to obtain a suitable compound for heat‐shrinkable tubes. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1049–1052, 2004     

Enhanced flow behaviors of metallocene‐catalyzed linear low‐density polyethylene during ultrasound‐assisted extrusion

The effect of ultrasound on flow behaviors of metallocene‐catalyzed linear low‐density polyethylene (mLLDPE) melt in capillary‐like die during the extrusion is investigated in this article. The rise in die temperature is found with increasing ultrasound power, especially at lower initial die temperature. At the same die temperature, the presence of ultrasound can decrease the apparent viscosity and the viscous flow activation energy of mLLDPE melt then increase its slip velocity at the capillary wall in the die. The flow behavior of mLLDPE melt is enhanced during ultrasound‐assisted extrusion as the presence of ultrasound can enhance the mobility and the orientation of entangled segments. It is also found that ultrasound can break the dispersed phase of mLLDPE/polyolefin elastomer (POE) blend into small pieces thus improve the homogeneous dispersion of POE phase in mLLDPE matrix. A possible mechanism for enhanced flow behaviors of mLLDPE melt because of the presence of ultrasound is also proposed. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Thermal analysis of high‐density polyethylene and low‐density polyethylene with enhanced biodegradability

The thermal properties of high‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) filled with different biodegradable additives (Mater‐Bi AF05H, Cornplast, and Bioefect 72000) were investigated with thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The DSC traces of the additives indicated that they did not undergo any significant phase change or transition in the temperature region typically encountered by a commercial composting system. The TGA results showed that the presence of the additive led to a thermally less stable matrix and higher residue percentages. The products obtained during the thermodegradation of these degradable polyolefins were similar to those from pure polyethylenes. The LDPE blends were thermally less stable than the HDPE blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 764–772, 2002     

Dynamic rheological properties of high‐density polyethylene/polystyrene blends extruded in the presence of ultrasonic oscillations

The linear rheological properties of high‐density polyethylene (HDPE), polystyrene (PS), and HDPE/PS (80/20) blends were used to characterize their structural development during extrusion in the presence of ultrasonic oscillations. The master curves of the storage shear modulus (G′) and loss shear modulus (G″) at 200°C for HDPE, PS, and HDPE/PS (80/20) blends were constructed with time–temperature superposition, and their zero shear viscosity was determined from Cole–Cole plots of the out‐of‐phase viscous component of the dynamic complex viscosity (η″) versus the dynamic shear viscosity. The experimental results showed that ultrasonic oscillations during extrusion reduced G′ and G″ as well as the zero shear viscosity of HDPE and PS because of their mechanochemical degradation in the presence of ultrasonic oscillations; this was confirmed by molecular weight measurements. Ultrasonic oscillations increased the slopes of log G′ versus log G″ for HDPE and PS in the low‐frequency terminal zone because of the increase in their molecular weight distributions. The slopes of log G′ versus log G″ for HDPE/PS (80/20) blends and an emulsion model were used to characterize the ultrasonic enhancement of the compatibility of the blends. The results showed that ultrasonic oscillations could reduce the interfacial tension and enhance the compatibility of the blends, and this was consistent with our previous work. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3153–3158, 2004     

Polyphosphazene/low‐density polyethylene blends: Miscibility and flame‐retardance studies

The effect of poly(dianilinephosphazene) (PDAP) on the processability, thermal behavior, crystallinity, morphology, mechanical properties, and flammability behavior of low‐density polyethylene (LDPE) was studied. Plasticorder traces of PDAP/LDPE blends implied good processability and miscibility. Thermogravimetric analysis showed that PDAP improved the thermal stability of LDPE. X‐ray diffraction results indicated that PDAP was a semicrystalline polymer, and the crystallinity of the blends decreased with increasing PDAP content. A new reflection at 2θ = 23.15° was found in wide‐angle X‐ray diffraction spectra of the blends, indicating that these two components interacted with one another. The scanning electron microscopy microstructures of the blends also supported these findings. Moreover, PDAP substantially enhanced the limited oxygen index and elongation at break of LDPE. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 709–714, 2002     

Structure and properties of polyamide 6 blends with low‐density polyethylene grafted by itaconic acid and with neutralized carboxyl groups

A comparative study of the structure and properties of two‐phase blends of polyamide 6 (PA6) and low‐density polyethylene (LDPE) modified in the course of reactive extrusion, by grafting of itaconic acid (IA) without neutralization of carboxyl groups (LDPE‐g‐IA) and with neutralized carboxyl groups (LDPE‐g‐IA^?M⁺) was carried out. It was shown that 30 wt % of LDPE‐g‐IA^?M⁺ introduced to PA6 resulted in blends of higher Charpy impact strength compared with that of PA6/LDPE‐g‐IA blends. The maximum increase was achieved when Mg(OH)₂ was used as a neutralizing agent. The blend morphology has a two‐phase structure with blurred interphases because of increased adhesion between the phases. The neutralization of carboxyl groups in grafted IA did not lead to two‐phase morphology of blends, which had a negative influence on the mechanical properties. It is believed that the differences in the impact strength were caused by the influence of the added neutralizing agents on the structure of interphases, which depends on both the interfaces adhesion and structural effects resulting from the nucleating behavior of the neutralizing agent. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1702–1708, 2004     

Evaluation of the thermal and mechanical properties of poly(ε‐caprolactone), low‐density polyethylene,and their blends

The thermal and mechanical properties of low‐density polyethylene (LDPE), poly(ε‐caprolactone) (PCL), and their blends were evaluated. Differential scanning calorimetry showed that increasing the PCL content of the blend did not change the LDPE melting temperature, but reduced the crystallinity by up to 16.8%. This behavior was related to interactions between the PCL chains and the crystalline phase of LDPE. Tensile strength and elongation at break values for the blends were lower than those for the pure polymers, which suggested an incompatibility between the polymers. The values for Young's modulus under tensile increased when PCL was added to LDPE. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91:3909–3914, 2004     

Polypropylene/linear low‐density polyethylene blends: Morphology,crystal structure,optical, and mechanical properties

The morphology, crystal structure, crystallization behavior, optical, and mechanical properties of isotactic polypropylene (iPP) blended with metallocene linear low‐density polyethylene (mLLDPE) and Ziegler–Natta linear low‐density polyethylene (zLLDPE), with and without nucleating agents, were investigated. The correlation between the structures and optical properties was investigated. The addition of linear low‐density polyethylenes (LLDPEs), nucleating agents, and poly(ethylene‐co‐octene) (POE) had little influence on the crystal form of the iPP. The growth along the b axis was favorable in the presence of nucleating agents and LLDPEs. The LLDPEs led to much finer crystal morphologies, and the nucleating agents further prohibited spherulite formation; consequently, light scattering from the bulk crystalline structure was reduced. In all blends, biphase morphology was observed, and POE could improve the adhesion between the iPP and mLLDPE. After blending with LLDPEs, the haze and stiffness decreased, and the gloss increased. mLLDPE enhanced the toughness whereas zLLDPE had a slight influence on it. The nucleating agents decreased the haze, increased the gloss more, and ameliorated the stiffness; however, they changed the toughness little. POE increased the toughness of the blend significantly, accompanied by a much lower haze, higher gloss, and almost the same stiffness. When the concentration of 1,3 : 2,4‐bis(3,4‐dimethyl‐benzylidene sorbitol) exceeded 0.25 wt %, the optical properties and mechanical properties leveled off. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Multiple shape memory effects of trans‐1,4‐polyisoprene and low‐density polyethylene blends

A novel series of shape memory blends of trans‐1,4‐polyisoprene (TPI) and low‐density polyethylene (LDPE) were prepared using a simple physical blending method. The mechanical, thermal and shape memory properties of the blends were studied and schemes proposed to explain their dual and triple shape memory behaviors. It was found that the microstructures played an important role in the shape memory process. In TPI/LDPE blends, both the TPI crosslinking network and LDPE crystalline regions could work as fixed domains, while crystalline regions of LDPE or TPI could act as reversible domains. The shape memory behaviors were determined by the components of the fixed and reversible domains. When the blend ratio of TPI/LDPE was 50/50, the blends showed excellent dual and triple shape memory properties with both high shape fixity ratio and shape recovery ratio. © 2017 Society of Chemical Industry     

Mechanical properties and morphology of polylactide,linear low‐density polyethylene,and their blends

Melt blending of linear low density polyethylene (LLDPE) and polylactide (PLA) was performed in an extrusion mixer with post extrusion blown film attachment with and without compatibilizer‐grafted low density polyethylene maleic anhydride. The blend compositions were optimized for tensile properties as per ASTM D 882‐91. On the basis of this, LLDPE 80 [80 wt % LLDPE and 20 wt % poly(L ‐lactic acid) (PLLA)] and MA‐g‐low‐density polyethylene 80/4 (80 wt % LLDPE, 20 wt % PLLA, and 4 phr compatibilizer) were found to be an optimum composition. The blends were characterized according to their mechanical, thermal, and morphological behavior. Fourier transform infrared spectroscopy revealed that the presence of compatibilizer enhanced the blend compatibility to some extent. The morphological characteristics of the blends with and without compatibilizer were examined by scanning electron microscopy. The dispersion of PLLA in the LLDPE matrix increased with the addition of compatibilizer. This blend may be used for packaging applications. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Transparent low‐density polyethylene/starch nanocomposite films

Low‐density polyethylene (LDPE)/starch nanocomposite films were prepared by melt extrusion process. The first step includes the preparation of starch–clay nanocomposite by solution intercalation method. The resultant product was then melt mixed with the main matrix, which is LDPE. Maleic anhydride‐grafted polyethylene (MAgPE), produced by reactive extrusion, was used as a compatibilizer between starch and LDPE phases. The effects of using compatibilizer, clay, and plasticizers on physico‐mechanical properties were investigated. The results indicated that the initial intercalation reaction of clay layers with starch molecules, the conversion of starch into thermoplastic starch (TPS) by plasticizers, and using MAgPE as a compatibilizer provided uniform distribution of both starch particles and clay layers, without any need of alkyl ammonium treatment, in LDPE matrix. The nanocomposite films exhibited better tensile properties compared to clay‐free ones. In addition, the transparency of LDPE film did not significantly change in the presence of TPS and clay particles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphology and rheological properties of compatibilized low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch blends

Morphology and rheological properties of low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) blends are experimentally investigated and theoretically analyzed using rheological models. Blending of LDPE/LLDPE (70/30 wt/wt) with 5–20 wt % of TPS and 3 wt % of PE‐grafted maleic anhydride (PE‐g‐MA) as a compatibilizer is performed in a twin‐screw extruder. Scanning electron micrographs show a fairly good dispersion of TPS in PE matrices in the presence of PE‐g‐MA. However, as the TPS content increases, the starch particle size increases. X‐ray diffraction patterns exhibit that with increase in TPS content, the intensity of the crystallization peaks slightly decreases and consequently crystal sizes of the blends decrease. The rheological analyses indicate that TPS can increase the elasticity and viscosity of the blends. With increasing the amount of TPS, starch particles interactions intensify and as a result the blend interface become weaker which are confirmed by relaxation time spectra and the prediction results of emulsion Palierne and Gramespacher‐Meissner models. It is demonstrated that there is a better agreement between experimental rheological data and Coran model than the emulsion models. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44719.     

Modification of low‐density polyethylene by graft copolymerization with maleic anhydride and blends with polyamide 6

Modification of low‐density polyethylene (LDPE) hyperbranched grafting with a maleic anhydride (MAH) was carried out using corotating twin screw extruder in the presence of benzoyl peroxide. The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were obtained with a corotating twin screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy The effects of variations in temperature, PA6 loading, and benzoyl peroxide and MAH concentration were investigated. The results show that most MAH monomers were grafted onto the LDPE at a lower MAH concentration. With the proper selection of the reaction parameters, we obtained a grafting degree higher than 4.9%. Mechanical test results indicate that the blends had good interfacial adhesion and good stability of the phase structure during heating, which was reflected in the mechanical properties. Furthermore, the results reveal that the tensile strength of the blends increased continuously with increasing PA6 content. Moreover, the home‐synthesized maleated LDPE could be used for the compatibilization of LDPE/PA 6 blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010