Preparation of chlorinated poly(vinyl chloride)‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membranes and their water permeation properties

Chlorinated poly(vinyl chloride) (CPVC) membranes for microfiltration processes were prepared with the combined process of a solvent evaporation technique and the water‐vapor induced‐phase‐inversion method. CPVC membranes with a mean pore size of 0.7 μm were very hydrophobic. These membranes were subjected to surface modification by ultraviolet (UV)‐assisted graft polymerization with N‐vinyl‐2‐pyrrolidinone (NVP) to increase their surface wettability and decrease their adsorptive fouling. The grafting yields of the modified membranes were controlled by alteration of UV irradiation time and NVP monomer concentration. The changes in chemical structure between the CPVC membrane and the CPVC‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membrane and the variation of the topologies of the modified PVC membranes were characterized by Fourier transform infrared spectroscopy, gel permeation chromatography, and field emission scanning electron microscopy. According to the results, the graft yield of the modified CPVC membrane reached a maximum at 5 min of UV exposure time and 20 vol % NVP concentration. The filtration behavior of these membranes was investigated with deionized water by a crossflow filtration measurement. The surface hydrophilicity and roughness were easily changed by the grafting of NVP on the surface of the CPVC membrane through a simultaneous irradiation grafting method by UV irradiation. To confirm the effect of grafting for filtration, we compared the unmodified and modified CPVC membranes with respect to their deionized water permeation by using crossflow filtration methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3188–3195, 2003     

Novel multimonomer‐grafted polypropylene preparation and application in polypropylene/poly(vinyl chloride) blends

A novel grafted polymer was prepared in one step through free‐radical melt grafting in a single‐screw extruder. It was shown that the addition of styrene (St) to the melt‐grafting system as a comonomer could significantly enhance the grafting degree of methyl methacrylate (MMA) onto polypropylene (PP) and reduce the degradation of the PP matrix by means of Fourier transform infrared and melt flow rate testing, respectively. Then, the potential of using multimonomer‐grafted PP, which was designated PP‐g‐(St‐co‐MMA), as the compatibilizer in PP/poly(vinyl chloride) (PVC) blends was also examined. In comparison with PP/PVC blends, the average size of the dispersed phase was greatly reduced in grafted polypropylene (gPP)/PVC blends because of the addition of the PP‐g‐(St‐co‐MMA) graft copolymer. The tensile strength of the gPP/PVC blends increased significantly, and the impact strength was unchanged from that of the pure PP/PVC blends. The results of differential scanning calorimetry and scanning electron microscopy suggested that the compatibility of the PP/PVC blends was improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

聚丙烯接枝物的制备及其在PP/PA6共混体系中的应用

以BPO为引发剂,通过悬浮固相接枝法,得到PP-g-（MAH/VAc）和PP-g-（MA/AA）接枝物,通过称重法和非水滴定法测得了接枝物的接枝率。红外光谱表明,单体都能接枝到PP上。SEM结果表明PP/PA6/PP接枝物共混体系中,PP-g-（MAH/VAc）的增容效果优于PP-g-（MA/AA）,这主要是因为PP-g（MAH/VAc）在PP/PA6体系中起到反应性增容的作用,而PP-g-（MA/AA）仅起到物理缠结的作用。     

Morphology and properties of PVC/clay nanocomposites via in situ emulsion polymerization

PVC/Na⁺–montmorillonite (MMT) nanocomposites were prepared via a simple technique of emulsion polymerization at several different MMT clay concentrations. X‐ray diffraction and transmission electron microscopy studies revealed the formation of a mixture of intercalated and exfoliated nanostructure. Tensile testing results showed that the tensile modulus of the nanocomposites increased with the addition of clay, while the tensile strength decreased little. The notched impact strength of the nanocomposites was also improved. For systems containing clay in the range of 2.1 to 3.5 wt %, the impact strength was almost two times as large as that of pure PVC. However, those mechanical properties began to decrease with the continuously increasing amount of clay. The fracture surface of pure PVC and the nanocomposites was observed by scanning electron microscope. Thermal properties of the nanocomposites were found to increase as a result of clay incorporation. The glass transition temperatures of the PVC/clay nanocomposites were nearly identical to that of pure PVC. The Vicat softening points exhibited a progressively increasing trend with the clay content added. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 277–286, 2004     

Compatibilization of polypropylene/nylon 6 blends with a polypropylene solid‐phase graft

The compatibilization of polypropylene (PP)/nylon 6 (PA6) blends with a new PP solid‐phase graft copolymer (gPP) was systematically studied. gPP improved the compatibility of PP/PA6 blends efficiently. Because of the reaction between the reactive groups of gPP and the NH₂ end groups of PA6, a PP‐g‐PA6 copolymer was formed as a compatibilizer in the vicinity of the interfaces during the melting extrusion of gPP and PA6. The tensile strength and impact strength of the compatibilized PP/PA6 blends obviously increased in comparison with those of the PP/PA6 mechanical blends, and the amount of gPP and the content of the third monomer during the preparation of gPP affected the mechanical properties of the compatibilized blends. Scanning electron microscopy and transmission electron microscopy indicated that the particle sizes of the dispersed phases of the compatibilized PP/PA6 blends became smaller and that the interfaces became more indistinct in comparison with the mechanical blends. The microcrystal size of PA6 and the crystallinity of the two components of the PP/PA6 blends decreased after compatibilization with gPP. The compatibilized PP/PA6 blends possessed higher pseudoplasticity, melt viscosity, and flow activation energy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 420–427, 2004     

Mechanical properties of recycled PVC blends with styrenic polymers

The aim of this study is to improve the performance of blends made from recycled polyvinyl chloride (PVC), coming from credit card waste, so that these blends can be used for those applications that must fulfil some requirements with regard to mechanical properties and stability with temperature alterations. With this aim in mind, two polymers of styrenic origin have been combined: styrene acrylonitrile (SAN) and acrylonitrile butadiene styrene (ABS). These polymers are characterized by a satisfactory balance of mechanical properties and thermal stability. PVC blends with both virgin and recycled styrenic polymers have been studied throughout the entire range of compositions. The prior degradation of the recycled materials has been studied by means of Fourier transformed infrared spectroscopy (FTIR).The behavior of the observed T_g values has been analyzed using differential scanning calorimetry (DSC), and the existence of partial miscibility between the different components has been studied. The mechanical properties have been determined using tensile and Charpy impact tests. The thermal stability of the PVC blends with temperature changes has been determined using the Vicat softening temperature (VST). Finally, the fracture surface of the various blends has been analyzed using scanning electron microscopy (SEM). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2464–2471, 2006     

Phase dispersion–crosslinking synergism in binary blends of poly(vinyl chloride) with low‐density polyethylene: Entrapping phenomenon in PVC/LDPE/DCP blend

The co‐crosslinked products and the entrapping phenomenon that may exist in a poly(vinyl chloride)/low density polyethylene/dicumyl peroxide (PVC/LDPE/DCP) blend were investigated. The results of selective extraction show that unextracted PVC was due to not being co‐crosslinked with LDPE but being entrapped by the networks formed by the LDPE phase. SBR, as a solid‐phase dispersant, can promote the perfection of networks of the LDPE phase when it is added to the PVC/LDPE blends together with DCP, which leads to more PVC unextracted and improvement of the mechanical properties of PVC/LDPE blends. Meanwhile, the improvement of the tensile properties is dependent mainly on the properties of the LDPE networks. Finally, the mechanism of phase dispersion–crosslinking synergism is presented. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1296–1303, 2003     

Preparation and thermomechanical characterization of poly(vinyl chloride) blends compatible with terpolymer‐containing maleic anhydride

In this study, I aimed to change the thermomechanical characteristics of poly(vinyl chloride) (PVC), which is widely used in commercial areas. Copolymers containing maleic anhydride (MA) units are commonly used to obtain compatible polymer blends. In our study, PVC blends were also prepared with the terpolymers with and without anhydride units. I assumed that the impact of the terpolymer on the thermomechanical characteristics of the PVC material could be more effectively controlled. For this purpose, two sets of six different blends of PVC with or without MA were synthesized, among which one was pure PVC, but the other five blends contained 2, 4, 6, 8, and 10% terpolymer. In conclusion, I observed that the terpolymer with the MA unit more regularly changed the thermomechanical characteristics of PVC. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1586–1589, 2004     

Mechanical properties and morphology of PP/ABS blends compatibilized with PP‐g‐2‐HEMA

Polypropylene (PP) and acrylonitrile–butadiene–styrene blends of different composition were prepared using a single‐screw extruder. The binary blend of PP/ABS was observed to be incompatible and shows poor mechanical properties. PP‐g‐2‐hydroxyethyl methacrylate (2‐HEMA) was used as a compatibilizer for the PP/ABS blends. The ternary compatibilized blends of PP/ABS/PP‐g‐2‐HEMA showed improvement in the mechanical properties. Electron micrographs of these blends showed a homogeneous and finer distribution of the dispersed phase. The mechanical performance increased particularly in the PP‐rich blend. The 2.5‐phr (part per hundred of resin) compatibilizer was observed to bring improvement to the properties. The suitability of various existing theoretical models for the predication of the tensile moduli of these blends was examined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 72–78, 2003     

Preparation,structure, and transport properties of ultrafiltration membranes of poly(vinyl chloride) (PVC), carboxylated poly(vinyl chloride) (CPVC), and PVC/CPVC blends

Ultrafiltration (UF) membranes were prepared from poly(vinyl chloride) (PVC), carboxylated poly(vinyl chloride) (CPVC), and PVC/CPVC blends by the phase-inversion method. The physical structure of the membranes was characterized by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The fouling characteristics of all the three membranes and acrylamide (AA)-grafted PVC membranes were characterized by ultrafiltration of bovine serum albumin (BSA) solution over a range of pH and of salt concentrations. Maximum adsorption of the protein on the membrane occurred near the isoelectric point of BSA and in the presence of the salts. The charge on BSA appears to be a dominant factor in determining the fouling. The UF results are explained in terms of nature of the membrane polymer, and effect of different ionic environments on the conformational changes of the protein. The ultrafiltration fluxes are correlated by a model based on the membrane resistance and the time-dependent resistance of the concentration polarization layer of the protein. The values of a mass transfer coefficient and concentration polarization were determined. Zeta potential of the membranes were also determined before and after the UF. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1117–1130, 1999     

Preparation and mechanical properties of poly(vinyl chloride)/bamboo flour composites with a novel block copolymer as a coupling agent

To improve the interfacial adhesion between poly(vinyl chloride) (PVC) and bamboo flour in PVC/bamboo flour composites, a novel coupling agent, poly(styrene‐co‐maleic anhydride)‐block‐poly(styrene‐co‐acrylonitrile) {P[(SMA)‐b‐(SAN)]}, was synthesized through living free‐radical polymerization in a one‐pot reaction. P[(SMA)‐b‐(SAN)] was synthesized by a nitroxide‐mediated polymerization technique in the presence of 2,2,6,6‐tetramethylpiperidin‐l‐oxyl with azobisisobutyronitrile. The conversion of maleic anhydride (>99%) and styrene (>65%) was relatively high and yielded P[(SMA)‐b‐(SAN)] with a narrow molecular weight distribution (weight‐average molecular weight/number‐average molecular weight <1.38). PVC was blended with bamboo flours in the presence of the synthesized coupling agent with a two‐roll mill. P[(SMA)‐b‐(SAN)] was added to the PVC matrix at a concentration of 55 or 20 wt %. As the content of P[(SMA)‐b‐(SAN)] in the wood–polymer composite increased, improved morphological and mechanical behaviors were observed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Analysis of low‐density polyethylene‐g‐poly(vinyl chloride) copolymers formed in poly(vinyl chloride)/low‐density polyethylene melt blends with gel permeation chromatography and solid‐state 13C‐NMR

Gel permeation chromatography (GPC) and solid‐state ¹³C‐NMR techniques were used to analyze the structural changes of poly(vinyl chloride) (PVC) in blends of a low‐density polyethylene (LDPE) and PVC during melt blending. The GPC results showed that the weight‐average molecular weight (M_w) of PVC increased with LDPE content up to 13.0 wt % and then decreased at a LDPE content of 16.7 wt %, whereas the number‐average molecular weight remained unchanged for all of LDPE contents used. The ¹³C‐NMR results suggest that the increase in M_w was associated with the formation of a LDPE‐g‐PVC structure, resulting from a PVC and LDPE macroradical cross‐recombination reaction during melt blending. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3167–3172, 2004     

Nonisothermal crystallization kinetics of polypropylene/polypropylene‐g‐polystyrene/polystyrene blends

The nonisothermal crystallization kinetics of polypropylene (PP), PP/polystyrene (PS), and PP/PP‐g‐PS/PS blends were investigated with differential scanning calorimetry at different cooling rates. The Jeziorny modified Avrami equation, Ozawa method, and Mo method were used to describe the crystallization kinetics for all of the samples. The kinetics parameters, including the half‐time of crystallization, the peak crystallization temperature, the Avrami exponent, the kinetic crystallization rate constant, the crystallization activation energy, and the F(T) and a parameters were determined. All of the results clearly indicate that the PP‐g‐PS copolymer accelerated the crystallization rate of the PP component in the PP/PP‐g‐PS/PS blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties of poly(vinyl chloride) blends and corresponding graft copolymers

The mechanical properties of the poly (vinyl chloride) (PVC) and poly (glycidyl methacrylate) [poly (GMA)] blend system and the PVC and poly (hydroxyethyl methacrylate) [poly (HEMA)] blend system and their crosslinked films were investigated. At the same time, the mechanical properties for the corresponding graft copolymers such as PVC-g-GMA, PVC-g-HEMA, and their crosslinked films were also investigated in this study. The results showed that the tensile strengths for PVC–poly (GMA) blend systems were higher than those for PVC-g-GMA graft copolymer, and the tensile strengths for PVC-g-HEMA were higher than those for PVC-poly (HEMA) blend systems. However, the mechanical properties for the PVC–poly (GMA) blend system were not affected by the crosslinking of the blend system, but those for PVC-poly (HEMA) and their graft copolymers decreased with an increase of the equivalent ratio ([NCO]/[OH]) of the crosslinker. Finally, the surface hydrophilicity of the PVC-g-HEMA graft copolymer and PVC-poly (HEMA) blends were also assessed through measuring the contact angle. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 307–319, 1998     

Fracture behavior of PVC/Blendex/nano‐CaCO3 composites

PVC/Blendex/Nano‐CaCO₃ composites were prepared by melt‐blending method. The Blendex (BLENDEX® 338) (GE Specialty Chemicals Co., Ltd., Shanghai, China) was an acrylonitrile‐butadiene‐styrene copolymer with high butadiene content. The fracture behavior of PVC/Blendex/nano‐CaCO₃ composites was studied using a modified essential work of fracture model, U/A = u₀ + u_dl, where u₀ is the limiting specific fracture energy and u_d is the dissipative energy density. The u₀ of PVC/Blendex blend could be greatly increased by the addition of nano‐CaCO₃, while the u_d was decreased. Nano‐CaCO₃ with particle size of 38 nm increased the u₀ of PVC/Blendex blend more effectively than that with particle size of 64 nm, when nano‐CaCO₃ content was below 10 phr. Both the u₀ and u_d of PVC/Blendex/nano‐CaCO₃ composites were not much affected by increasing specimen thickness from 3 mm to 5 mm, while the two fracture parameters were increased with increasing loading rate from 2 mm/min to 10 mm/min, and u_d was found to be more sensitive to the loading rate than u₀. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 953–961, 2005     

Preparation of intercalated Mg‐Al layered double hydroxides and its application in PVC thermal stability

The Mg‐Al oxide precursor prepared by the calcination of Mg‐Al‐carbonated layered double hydroxide (LDH) at 500 K for 4 h is used as the host material, 2‐hydroxy‐4‐methoxybenzophenone‐5‐sulfonic acid (BP) is used as the guest material, BP‐intercalated LDH (LDH‐BP) is prepared by ion‐exchange method. The structure of LDH‐BP is characterized by X‐ray diffraction (XRD), Fourier transform infrared (FTIR), and thermogravimetry and differential thermal analysis (TG‐DTA). The thermal stability of PVC/BP, PVC/LDH, PVC/LDH‐BP composites, as well as pure PVC is investigated by conventional Congo Red test and dynamic thermal stability analysis in both the open and closed processing environments. According to XRD and FTIR, BP anions have been intercalated into interlayer galleries of LDH. TG‐DTA results show that the layer‐anionic interaction results in the improvement of the thermal stability of BP. Congo Red tests indicate that the addition of BP catalyzes the thermal degradation of PVC. A little amount of LDH (such as 1 phr) makes PVC more stable, but excessive addition accelerates the thermal degradation of PVC. The addition of LDH‐BP markedly improves the static thermal stability of PVC. The results of dynamic thermal stability tests in both the open and closed processing environments are consistent with that of Congo Red tests. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of PVC‐bound N,N‐dialkylaminopyridine

A linear poly(vinyl chloride) (PVC)‐supported dialkylaminopyridine was prepared through PVC treated with N‐methylaminopyridine and NaH in tetrahydrofuran. The properties of this PVC‐bound catalyst were examined by acetylation of linalool and 5‐FU. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1067–1069, 2002; DOI 10.1002/app.10391     

PA6含量对PVC/PA6共混物形态结构与力学性能的影响

以EVA-g-MAH为相容剂,将PVC与自制的低熔点PA6共混制备了PVC/PA6共混物。通过扫描电子显微镜(SEM)和力学性能测试研究了PA6含量对PVC/PA6共混物形态结构及力学性能的影响。SEM分析结果显示:随着PA6含量的增加,PVC/PA6共混物的分散相尺寸逐渐增大,当PA6含量为10%时,共混物中分散相的分散尺寸最小为1μm;当PA6含量为50%时,共混物为两相共连续结构;当PA6含量为60%时,共混物中PA6为连续相,PVC为分散相。力学性能测试结果表明:当PA6含量为10%时,共混物的缺口冲击强度和拉伸强度都较PVC有明显提高,分别提高了约50%与30%,达到了6.29kJ/m2和60MPa。采用差示扫描量热仪(DSC)研究了PVC/PA6共混物的结晶温度,检测结果显示:PVC/PA6共混物呈现非晶结构。     

Preparation of poly(vinyl chloride) (PVC) ultrafiltration membranes from PVC/additive/solvent and application of UF membranes as substrate for fabrication of reverse osmosis membranes

Ultrafiltration (UF) membranes were prepared from poly(vinyl chloride) (PVC) as main polymer, poly(vinyl pyrrolidone) (PVP) as additive, and 1‐methyl‐2‐pyrrolidone (NMP) as solvent using Design Expert software for designing the experiments. The membranes were characterized by SEM, contact angle measurement, and atomic force microscopy. The performance of UF membranes was evaluated by pure water flux (PWF) and blue indigo dye particle rejection. In addition, the molecular weight cutoff of UF membranes was determined by poly(ethylene glycol) (PEG) rejection. The UF membranes were used as substrates for fabrication of polyamide thin film composite (TFC) reverse osmosis (RO) membranes. The results showed that the model had high reliability for prediction of PWF of UF membranes. Also, increment in PVC concentration caused reduction of PWF. Moreover, at constant PVC concentration and if the concentrations of PVC was lower than 10 wt %, the PWF reduced by increasing the concentration of PVP. However, at PVC concentration higher than 11 wt %, increment in PVP concentration showed increment and reduction of PWF. The PEG rejection results showed that the prepared membranes had UF membranes properties. Finally, the NaCl rejection tests of RO membranes by PVC as substrates indicated that the performance of RO membranes were lower than commercial membranes. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46267.     

Structure and properties of polyimide‐g‐nylon 6 and nylon 6‐b‐polyimide‐b‐nylon 6 copolymers

Polyimide‐g‐nylon 6 copolymers were prepared by the polymerization of phenyl 3,5‐diaminobenzoate with several diamines and dianhydrides with a one‐step method. The polyimides containing pendant ester moieties were then used as activators for the anionic polymerization of molten ε‐caprolactam. Nylon 6‐b‐polyimide‐b‐nylon 6 copolymers were prepared by the use of phenyl 4‐aminobenzoate as an end‐capping agent in the preparation of a series of imide oligomers. The oligomers were then used to activate the anionic polymerization of ε‐caprolactam. In both the graft and copolymer syntheses, the phenyl ester groups reacted quickly with caprolactam anions at 120°C to generate N‐acyllactam moieties, which activated the anionic polymerization. All the block copolymers had higher moduli and tensile strengths than those of nylon 6. However, their elongations at break were much lower. The graft copolymers based on 2,2′‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]propane dianhydride and 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane displayed elongations comparable to that of nylon 6 and the highest moduli and tensile strengths of all the copolymers. The thermal stability, moisture resistance, and impact strength were dramatically increased by the incorporation of only 5 wt % polyimide into both the graft and block copolymers. The graft and block copolymers also exhibited improved melt processability. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 300–308, 2006