Influence of calcium carbonate filler and mixing type process on structure and properties of styrene–acrylonitrile/ethylene–propylene–diene polymer blends

The properties of styrene–acrylonitrile (SAN) and ethylene–propylene–diene (EPDM) blends containing different types of calcium carbonate filler were studied. The influence of mixing type process on the blend properties was also studied. Two different mixing processes were used. The first one includes mixing of all components together. The other process is a two‐step mixing procedure: masterbatch (MB; EPDM/SAN/filler blend) was prepared and then it was mixed with previously prepared polymer blend. Surface energy of samples was determined to predict the strength of interactions between polymer blend components and used fillers. The phase morphology of blends and their thermal and mechanical properties were studied. From the results, it can be concluded that the type of mixing process has a strong influence on the morphological, thermal, and mechanical properties of blends. The two‐step mixing process causes better dispersion of fillers in blends as well as better dispersion of EPDM in SAN matrix, and therefore, the finest morphology and improved properties are observed in blends with MB. It can be concluded that the type of mixing process and carefully chosen compatibilizer are the important factors for obtaining the improved compatibility of SAN/EPDM blends. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of anhydride‐modified ethylene–propylene–diene rubber and ethylene–vinyl acetate copolymers on the compatibilization of nitrile rubber/ethylene–propylene–diene rubber blends

The effects of maleic anhydride modified ethylene–propylene–diene rubber (EPDMMA) and maleic anhydride modified ethylene–vinyl acetate (EVAMA) on the compatibilization of nitrile rubber (NBR)/ethylene–propylene–diene rubber (70:30 w/w) blends vulcanized with a sulfur system were investigated. The presence of EPDMMA and EVAMA resulted in improvements of the tensile properties, whereas no substantial change was detected in the degree of crosslinking. The blend systems were also analyzed with scanning electron microscopy and dynamic mechanical thermal analysis. The presence of EVAMA resulted in a blend with a more homogeneous morphology. The compatibilizing effect of this functional copolymer was also detected with dynamic mechanical analysis. A shift of the glass‐transition temperature of the NBR phase toward lower values was observed. The presence of EPDMMA and EVAMA also increased the thermal stability, as indicated by an improvement in the retention of the mechanical properties after aging in an air‐circulating oven. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2408–2414, 2003     

Influence of comonomer incorporation on morphology and thermal and mechanical properties of blends based upon isotactic metallocene–polypropene and random ethene/1‐butene copolymers

Blends of isotactic polypropene (i‐PP) with random ethene/1‐butene (EB) copolymers containing 10, 24, 48, 58, 62, 82, and 90 wt % 1‐butene were prepared in order to examine the influence of the EB molecular architecture on the morphology development as well as on the thermal and mechanical properties. Compatibility between i‐PP and EB increased with increasing 1‐butene content in EB to afford single‐phase blends at a 1‐butene content exceeding 82 wt %. The morphology was investigated using AFM and TEM. Improved compatibility accounted for enhanced EB dispersion and interfacial adhesion. Highly flexible as well as stiff blends with improved toughness were obtained. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 838–848, 1999     

Effects of maleated styrene–(ethylene‐co‐butene)–styrene on compatibilization and properties of nylon‐12,12/nylon‐6 blends

Effects of a maleated triblock copolymer of styrene–(ethylene‐co‐butene)–styrene (SEBS‐g‐MA) on compatibilization and mechanical properties of nylon‐12,12/nylon‐6 blends were investigated. The results showed that addition of SEBS‐g‐MA could improve the compatibility between nylon‐12,12 and nylon‐6. Nylon‐12,12 could disperse very well in nylon‐6 matrix, although the dispersion of nylon‐6 was poor when nylon‐6 was the dispersed phase. At a fixed nylon‐12,12/nylon‐6 ratio of 30/70, supertoughness was achieved with addition of 15% SEBS‐g‐MA in weight. Scanning electron microscopy of the impact‐fractured surface indicated that cavitation and matrix shear yielding were the predominant mechanisms of impact energy dissipation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1446–1453, 2004     

Effect of molecular structure and rheology on the compression foam molding of ethylene‐α‐olefin copolymers

The morphology and mechanical properties of foams made out of a series of ethylene‐α‐olefin copolymers having well‐characterized rheological properties were investigated. A compression foaming molding technique was implemented, using azodicarbonamide as the blowing agent. The polymers differed in the amount of comonomer contained (resulting in a range of densities), type of comonomer (octene vs. butene) and molecular weight, resulting in variable thermal properties and different rheological responses under shear and extensional flow. The results showed that the majority of the octene‐based copolymers with comparable rheological properties had similar foam morphology. A distinct behaviour was observed for the butene‐based copolymer, as well as the octene‐containing one having the lowest density and lowest melting/crystallization points. The poor foamability of these grades was attributed to their differences in extensional and thermal properties, respectively. Increasing density resulted in a higher secant modulus of the foamed samples. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Rotational molding of polypropylene/ultra‐low‐density ethylene‐α‐olefin copolymer blends

This work investigates the performance of blends in rotational molding, by using an industrially relevant system consisting of polypropylene (PP) and an ultra‐low‐density ethylene‐α‐olefin copolymer (or polyolefin plastomer, POP). Specifically, the effect of POP content and PP type on the sintering and densification behavior, as well as the rotomolded part properties and morphology, was examined. The sinter‐melting curves of these blends exhibited bimodality, due to the wide melting point difference between the two polymers. Increasing POP content resulted in higher sintering and densification rates, as well as improved impact properties and elongation at break, counteracted by lower stiffness. Selection of a polypropylene component with lower viscosity led to better sintering and densification characteristics, due to enhanced flow properties. Better overall performance in terms of mechanical properties was obtained when polypropylene/polyethylene impact copolymers, as opposed to a PP homopolymer, were used. Polym. Eng. Sci. 44:1662–1669, 2004. © 2004 Society of Plastics Engineers.     

Polyamide‐reinforced ethylene–propylene–diene rubber compatibilized with chlorinated polyethylene

Vulcanizates of blends of ethylene–propylene–diene rubber and polyamide copolymers were prepared by reactive compatibilization. A reactive route was employed for compatibilizing these blends with the addition of chlorinated polyethylene (CPE). The influence of the compatibilizers, crosslinking agents, blend compositions, and addition modes of the compatibilizers on the mechanical properties of the blends was investigated. The morphologies of the blends were determined with scanning electron microscopy. The addition of CPE was found to reduce the particle size of the dispersed phase remarkably. The stability of the blends with compatibilizers was measured by high‐temperature thermal aging. The mechanical properties were examined by stress–strain measurements and dynamic mechanical thermal measurements; the addition of polyamide copolymers caused significant improvements in the tensile properties of these blends.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1727–1736, 2003     

Use of a sodium ionomer as a compatibilizer in polypropylene/high‐barrier ethylene–vinyl alcohol copolymer blends: The processability of the blends and their physical properties

The effect of a sodium ionomer (ion.Na⁺) on the compatibility of polypropylene (PP)/high‐barrier ethylene–vinyl alcohol copolymer (EVOH) blends was studied in terms of the thermal, mechanical, and optical properties and morphology. The rheological behavior, tensile tests, and morphology of the binary blends showed that the miscibility of EVOH with PP was very poor. The miscibility of the polymers improved with the ionomer addition. In general, the ion.Na⁺ concentration did not alter the thermal behavior of the blends, but it did improve the ductility of the injection‐molded specimens. Scanning electron micrographs displayed better adhesion between the PP and EVOH phases in the samples with the ionomer. The mechanical improvement was better in the film samples than in the injection‐molded samples. A 90/10 (w/w) PP/EVOH film with 5% ion.Na⁺ and an 80/20 (w/w) PP/EVOH film with 10% ion.Na⁺ presented better global properties than the other blends studied. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1763–1770, 2004     

Thermal properties and adhesion strength of amorphous poly(α‐olefins)/styrene–ethylene–butylene copolymer/terpene hot‐melt adhesive

The thermal stability and adhesion properties, such as lap‐shear strength of hot‐melt adhesives were obtained from amorphous poly(α‐olefins) and thermoplastic rubber [styrene–ethylene–butylene copolymer (SEBS)] blends. The addition of SEBS increased the toughness and viscosity and decreased the lap‐shear strength of the hot‐melt adhesive. Terpene tackifier resin offered enhanced lap‐shear strength; this was more effective when combined tackifier resin was added on the hot‐melt adhesive. Only a small amount of wax and antioxidant affected the thermal stability and lap‐shear strength of the hot‐melt adhesive. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Compatibilization of nitrile‐butadiene rubber/ethylene‐propylene‐diene monomer blends by mercapto‐modified ethylene‐vinyl acetate copolymers

Mercapto‐modified ethylene‐vinyl acetate (EVASH) has been employed as a reactive compatibilizing agent for nitrile‐butadiene rubber (NBR)/ethylene‐propylene‐diene monomer (EPDM) blends vulcanized with a sulfur/2,2′‐dithiobisbenzothiazole (MBTS) single accelerator system and a (sulfur/MBTS/tetramethylthiuram disulfide (TMTD) binary accelerator system. The addition of 5.0 phr EVASH resulted in a significant improvement in the tensile properties of blends vulcanized with the sulfur/MBTS system. In addition to better mechanical performance, these functionalized copolymers gave rise to a more homogeneous morphology and, in some cases, better aging resistance. The compatibilization was not efficient in blends vulcanized with the S/MBTS/TMTD binary system, probably because of the faster vulcanization process occurring in this system. The good performance of these EVASH samples as compatibilizing agents for NBR/EPDM blends is attributed to the higher polarity of these components that is associated with their lower viscosity. Dynamic mechanical analysis also suggested a good interaction between the phases in the presence of EVASH. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1404–1412, 2004     

Silica‐reinforced dynamically vulcanized ethylene–propylene–diene monomer/polypropylene thermoplastic elastomers: Morphology,rheology, and dynamic mechanical properties

Attempts were made to prepare dynamically crosslinked ethylene–propylene–diene monomer/polypropylene (EPDM/PP, 60/40 w/w) blends loaded with various amounts of silica as a particulate reinforcing agent. The dispersion of silica between the two phases under mixing conditions, and also extent of interaction, as the two main factors that influence the blend morphology were studied by scanning electron microscopy. Increasing the silica concentration led to the formation of large‐size EPDM aggregates shelled by a layer of PP. Dynamic mechanical thermal analysis performed on the dynamically cured silica‐loaded blend samples showed reduction in damping behavior with increasing silica content. Higher rubbery‐like characteristics under tensile load were exhibited by the silica‐filled EPDM/PP‐cured blends. However, increasing the silica level to 50 phr led to the enhancement of interface, evidenced by increases in the tensile modulus and extensibility of the blend compared with those of the unloaded sample. Addition of a silane coupling agent (Si69) into the mix improved the mechanical properties of the blend, attributed to the strengthening of interfacial adhesion between the PP matrix and silica‐filled EPDM phase. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2000–2007, 2004     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

Blends of SBS triblock copolymer with poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polystyrene mixture

Blends of styrene–butadiene–styrene (SBS) or styrene–ethylene/1‐butene–styrene (SEBS) triblock copolymers with a commercial mixture of polystyrene (PS) and poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) were prepared in the melt at different temperatures according to the chemical kind of the copolymer. Although solution‐cast SBS/PPO and SBS/PS blends were already known in the literature, a general and systematic study of the miscibility of the PS/PPO blend with a styrene‐based triblock copolymer in the melt was still missing. The thermal and mechanical behavior of SBS/(PPO/PS) blends was investigated by means of DSC and dynamic thermomechanical analysis (DMTA). The results were then compared to analogous SEBS/(PPO/PS) blends, for which the presence of a saturated olefinic block allowed processing at higher temperatures (220°C instead of 180°C). All the blends were further characterized by SEM and TGA to tentatively relate the observed properties with the blends' morphology and degradation temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2698–2705, 2003     

Effects of maleated styrene–(ethylene‐co‐butene)–styrene on the morphology and mechanical and thermal properties of polystyrene/polyamide 1212 blends

Polystyrene (PS)/polyamide 1212 (PA 1212) blends were compatibilized with a maleated triblock copolymer of styrene–(ethylene‐co‐butene)–styrene (SEBS‐g‐MA). Scanning electron microscopy revealed that the addition of SEBS‐g‐MA was beneficial to the dispersion of PA 1212 in the PS matrix because of the reaction between them. The variation of the fraction of SEBS‐g‐MA in the blends allowed the manipulation of the phase structure, which first formed a sheetlike structure and then formed a cocontinuous phase containing PA 1212/SEBS‐g‐MA core–shell morphologies. As a result, the mechanical properties, especially the Charpy notched impact resistance, were significantly improved with the addition of SEBS‐g‐MA. Differential scanning calorimetry (DSC) data indicated that the strong interaction between SEBS‐g‐MA and PA 1212 in the blends retarded the crystallization of PA 1212. The heat distortion temperature of the compatibilized blends was improved in comparison with that of the unmodified blend, probably because of the apparent increase in the glass‐transition temperature with an increasing concentration of SEBS‐g‐MA. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1354–1360, 2005     

Miscibility of blends of ethylene‐propylene‐diene terpolymer and polypropylene

The miscibility of polymers is not only an important basis for selecting a proper blending method, but it is also one of the key factors in determining the morphology and properties of the blends. The miscibility between ethylene‐propylene‐diene terpolymer (EPDM) and polypropylene (PP) was explored by means of dynamic mechanical thermal analysis, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The results showed that a decrease in the PP content and an increase of the crosslinking density of EPDM in the EPDM/PP blends caused the glass‐transition temperature peaks of EPDM to shift from a lower temperature to higher one, yet there was almost no variance in the glass‐transition temperature peaks of PP and the degree of crystallinity of PP decreased. It was observed that the blends prepared with different mixing equipment, such as a single‐screw extruder and an open mill, had different mechanical properties and blends prepared with the former had better mechanical properties than those prepared with the latter. The TEM micrographs revealed that the blends were composed of two phases: a bright, light PP phase and a dark EPDM phase. As the crosslinking degree of EPDM increased, the interface between the phases of EPDM and PP was less defined and the EPDM gradually dispersed in the PP phase became a continuous phase. The results indicated that EPDM and PP were both partially miscible. The mechanical properties of the blends had a lot to do with the blend morphology and the miscibility between the blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 315–322, 2002     

Effect of octene content in poly(ethylene‐co‐1‐octene) on the properties of poly(propylene)/poly(ethylene‐co‐1‐octene) blends

Ethylene‐octene random copolymer (EOC) is one of the most commonly employed elastomers for PP, and as such its rubber toughening efficiency has been extensively studied. However, most existing studies employ EOC containing an octene comonomer of about 8 mol %. Therefore, in this study, we investigated the effect of EOC octene comonomer content on the morphology and thermal and mechanical properties of PP‐ethylene random copolymer (PP‐CP)/EOC (80/20 wt %/wt %) blends. It was clearly shown that the properties of the blends are significantly affected by the octene content. The rubber particle size of the blends decreased as the octene content in the EOC was increased, which was a consequence of the reduced interfacial tension between PP‐CP and EOC. Impact strength of the blends as a function of octene content displayed a brittle‐ductile transition. The tensile yield strength and modulus of the PP‐CP/EOC blends were decreased by addition of EOC, owing to incorporation of the soft EOC into the hard PP‐CP. The tensile yield strength and modulus of PP‐CP/EOC blends decreased monotonically with the octene content in the EOC. The melting temperature as well as the crystallinity of the PP‐CP phase were not affected significantly by the addition of EOC whereas a notable shift in melting and crystallization temperatures was observed for the EOC phase. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1133–1139, 2007     

Conducting blends of poly(o‐toluidine) and ethylene–propylene–diene terpolymer

Poly(o‐toluidine) (POT) is an electroactive polymer with poor mechanical and thermal characteristics. We examined the scope for improving such properties by making blends of POT with ethylene–propylene–diene rubber (EPDM). We prepared POT–EPDM blends containing different weight fractions of POT by intimately mixing known volumes of separate solutions of the two polymers (POT in THF and EPDM in toluene). Films of EPDM and POT–EPDM blends in solution were obtained by spreading, solvent evaporation, and film casting techniques. POT, EPDM, and their blends were characterized in solution by ultraviolet‐visible spectroscopy, and the respective dried samples were analyzed by Fourier transform infrared spectroscopy and thermogravimetry. The polymer samples were further analyzed morphologically by scanning electron microscopy, and their tensile strengths were also evaluated. Spectroscopic and thermal studies of the blends indicated some sort of interaction between the two constituent polymers. The direct current electrical conductivity of the blends in increasing order of POT loading (12.5–100%) was in the range 9.9 × 10^?5 to 11.6 × 10^?2 S cm^?1. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2550–2555, 2003     

Melt‐state miscibility of poly(ethylene‐co‐1‐octene) and linear polyethylene

On purpose to examine the effect of branch length on the miscibility of polyolefin blends, miscibility behavior of linear polyethylene/poly(ethylene‐co‐1‐octene) blend was studied and compared to that of linear polyethylene/poly(ethylene‐co‐1‐butene) blend. Miscibility of the blend was determined by observing the morphology quenched from the melt, and by using the relation between interaction parameter and copolymer composition. When the weight composition and molecular weight was the same, poly(ethylene‐co‐1‐octene) was slightly more miscible with linear polyethylene than poly(ethylene‐co‐1‐butene) was. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study on composition and characteristics of maleated ethylene‐octene copolymer prepared by reactive extrusion on the morphology and properties of polyamide 6/ethylene‐octene copolymer blends

Blends of polyamide 6 (PA6) and elastomeric ethylene‐octene copolymer (EOR), with and without maleated EOR (EOR‐MA) were studied. EOR‐MA with various amounts of grafted MA and gel content were prepared by reactive extrusion. The effects of EOR‐MA characteristics and composition on the morphology, thermal and mechanical properties of the blends were investigated. EOR‐MA was found to promote the toughness efficiency of PA6 remarkably. High impact resistance was achieved by the use of EOR‐MA containing less than 2% gel. The content of MA grafted on EOR‐MA in the range of 0.5%–1.0% gave a similar effect on the blend properties. The blend containing 20% of EOR grafted with 1% MA exhibited twenty times higher impact strength (1000 J/m) than pure PA6 (55 J/m). The presence of EOR‐MA in the blends led not only to a drastic reduction in the dispersed particle size, but also to some changes in fracture mechanisms, thus enhancing the impact resistance of the blends.     

Compatibilization of high‐impact polystyrene/high‐density polyethylene blends by styrene/ethylene–butylene/styrene block copolymer

Compatibilization of polymer blends of high‐impact polystyrene (HIPS) and high‐density polyethylene (HDPE) blend by styrene/ethylene–butylene/styrene (SEBS) was elucidated. Polymer blends containing many ratios of HIPS and HDPE with various concentrations of SEBS were prepared. The Izod impact strength and elongation at break of the blends increased with increases in SEBS content. They increased markedly when the HDPE content was higher than 50 wt %. Tensile strength of blends increased when the SEBS concentration was not higher than 5 pphr. Whenever the SEBS loading was higher than 5 pphr, the tensile strength decreased and a greater decrease was found in blends in which the HDPE concentration was more than 50 wt %. The log additivity rule model was applied to these blends, which showed that the blends containing the HIPS‐rich phase gave higher compatibility at the higher shear rates. Surprisingly, the blends containing the HDPE‐rich phase yielded greater compatibility at the lower shear rates. Morphology observations of the blends indicated better compatibility of the blends with increasing SEBS concentration. The relaxation time (T₂) values from the pulsed NMR measurements revealed that both polymer blends became more compatible when the SEBS concentration was increased. When integrating all the investigations of compatibility compared with the mechanical properties, it is possible to conclude that SEBS promotes a certain level of compatibilization for several ratios of HIPS/HDPE blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 742–755, 2004