Evaluation of melamine‐modified urea‐formaldehyde resins as particleboard binders

Particleboards bonded with 6 and 12% melamine‐modified urea‐formaldehyde (UMF) resins were manufactured using two different press temperatures and press times and the mechanical properties, water resistance, and formaldehyde emission (FE) values of boards were measured in comparison to a typical urea‐formaldehyde (UF) resin as control. The formaldehyde/(urea + melamine) (F/(U + M)) mole ratio of UMF resins and F/U mole ratio of UF resins were 1.05, 1.15, and 1.25 that encompass the current industrial values near 1.15. UMF resins exhibited better physical properties, higher water resistance, and lower FE values of boards than UF resin control for all F/(U + M) mole ratios tested. Therefore, addition of melamine at these levels can provide lower FE and maintain the physical properties of boards. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Curing of low level melamine‐modified urea‐formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)

Effects of resin formulation, catalyst, and curing temperature were studied for particleboard binder‐type urea‐formaldehyde (UF) and 6 ～ 12% melamine‐modified urea‐melamine‐formaldehyde (UMF) resins using the dynamic mechanical analysis method at 125 ～ 160°C. In general, the UF and UMF resins gelled and, after a relatively long low modulus period, rapidly vitrified. The gel times shortened as the catalyst level and resin mix time increased. The cure slope of the vitrification stage decreased as the catalyst mix time increased, perhaps because of the deleterious effects of polymer advancements incurred before curing. For UMF resins, the higher extent of polymerization effected for UF base resin in resin synthesis increased the cure slope of vitrification. The cure times taken to reach the vitrification were longer for UMF resins than UF resins and increased with increased melamine levels. The thermal stability and rigidity of cured UMF resins were higher than those of UF resins and also higher for resins with higher melamine levels, to indicate the possibility of bonding particleboard with improved bond strength and lower formaldehyde emission. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 377–389, 2005     

Colloidal aggregation of aminoplastic polycondensation resins: Urea–formaldehyde versus melamine–formaldehyde and melamine–urea–formaldehyde resins

Colloidal particles formation followed by their clustering have been shown to be the normal way of ageing of aminoplastic resins, namely urea–formaldehyde (UF) resins, melamine–formaldehyde (MF) resins, and melamine–urea–formaldehyde (MUF) resins. Ageing or further advancement of the resin by other means such as longer condensation times causes whitening of the resin. This is a macroscopic indication of both the formation of colloidal particles and of their clustering. It eventually progresses to resins, which are mostly in colloidal, clustered state, followed much later on by a supercluster formation starting to involve the whole resin. The initial, filament‐like colloidal aggregates formed by UF resins have different appearance than the globular ones formed by MF resins. MUF resins present a short rod‐like appearance hybrid between the two. GPC has been shown to detect the existence of colloidal superaggregates in a UF resin, while smaller aggregates might not be detected at all. The star‐like structures visible in the colloidal globules of MF resins are likely to be light interference patterns of the early colloidal structures in the resins. These star‐like interference patterns become more complex with resin ageing or advancement due to the advancement of the resin to more complex aggregates, to eventually reach the stage in which filament‐like and rod‐like structures start to appear. The next step is formation of globular masses that are representative of the true start of physical gelation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1406–1412, 2006     

Testing by fourier transform infrared species variation during melamine–urea–formaldehyde resin preparation

The preparation of an industrially used sequential formulation of a melamine–urea–formaldehyde resin was followed with Fourier transform infrared (FTIR). The analysis allowed us to identify the increases and decreases of the main groups in the resin and to compare this system of resin analysis with results previously obtained by ¹³C‐NMR analysis. The FTIR analysis, although considerably more limited than ¹³C‐NMR analysis, allowed us nonetheless to identify and follow the appearance, increase, decrease, and disappearance of several of the main chemical groups during the preparation of the initial urea–formaldehyde (UF) phase of the reaction and the subsequent reaction of melamine with the UF resin that was formed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Examination of selected synthesis parameters for wood adhesive‐type urea–formaldehyde resins by 13C NMR spectroscopy. III

The varying polymer structures of wood adhesive‐type urea–formaldehyde resins resulting from different formaldehyde/first urea (F/U₁) mole ratios used in the first step of resin manufacture were investigated using ¹³C. As the F/U₁ mole ratio decreased progressively from 2.40 to 2.10 and to 1.80, the viscosity increase due to polymerization during resin synthesis became faster and resulted in decreasing side‐chain branches and increasing free urea amide groups in the resin structure. The resultant UF resins, with the second urea added to an overall F/(U₁ + U₂) of 1.15, showed viscosity decreases when heated with stirring or allowed to stand at room temperature that were also characteristic with the F/U₁ mole ratios used in resin synthesis. The formaldehyde emission levels of particleboards bonded with the freshly made UF resins showed relatively small but similarly characteristic variations. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2800–2814, 2001     

Comparative 13C‐NMR and matrix‐assisted laser desorption/ionization time‐of‐flight analyses of species variation and structure maintenance during melamine–urea–formaldehyde resin preparation

The preparation of an industrially used sequential formulation of a melamine–urea–formaldehyde resin was followed by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry and ¹³C‐NMR analysis. The analysis allowed us to identify and follow the appearance, increase, decrease, and disappearance of a multitude of chemical species during the preparation of both the initial urea–formaldehyde (UF) phase of the reaction and the subsequent reaction of melamine with the UF resin that formed. The analysis indicated that (1) the increase and decrease in the species that formed proceeded through a cycle of the formation and degradation of species occurring continuously through what appeared to be a series of complex equilibria, (2) even at the end of the reaction a predominant proportion of methylene ether bridges was still present, (3) some small proportion of methylene bridges already had formed in the UF reaction phase of the resin even under rather alkaline conditions, and (4) the addition of melamine to the UF prepolymer induced some noticeable rearrangement of methylene ether bridges to methylene bridges. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Low‐volatility acetals to upgrade the performance of melamine–urea–formaldehyde wood adhesive resins

1,1,2,2‐Tetramethoxyethane (TME), a high boiling point acetal derived from glyoxol, lhas been shown to upgrade the performance of melamine‐urea‐formaldehyde (MUF) and some UF resins used for wood adhesives. This affords the possibility of decreasing the percentage of resin used in the preparation of wood panels without volatilizing the TME acetal used.     

Uron and uron–urea‐formaldehyde resins

The favored pH ranges for the formation of urons in urea‐formaldehyde (UF) resins preparation were determined, these being at pH's higher than 6 and lower than 4 at which the equilibrium urons ↔ N,N′‐dimethylol ureas are shifted in favor of the cyclic uron species. Shifting the pH slowly during the preparation from one favorable range to the other causes shift in the equilibrium and formation of a majority of methylol ureas species, whereas a rapid change in pH does not cause this to any great extent. UF resins in which uron constituted as much as 60% of the resin were prepared and the procedure to maximize the proportion of uron present at the end of the reaction is described. Uron was found to be present in these resins also as linked by methylene bridges to urea and other urons and also as methylol urons, the reactivity of the methylol group of this latter having been shown to be much lower than that of the same group in methylol ureas. Thermomechanical analysis (TMA) tests and tests on wood particleboard prepared with uron resins to which relatively small proportions of urea were added at the end of the reaction were capable of gelling and yielding bonds of considerable strength. Equally, mixing a uron‐rich resin with a low F/U molar ratio UF resin yielded resins of greater strength than a simple UF of corresponding molar ratio indicating that UF resins of lower formaldehyde emission with still acceptable strength could be prepared with these resins. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 277–289, 1999     

Hydrolytic stability of cured urea‐formaldehyde resins modified by additives

Urea‐formaldehyde (UF) resins are prone to hydrolysis that results in low‐moisture resistance and subsequent formaldehyde emission from UF resin‐bonded wood panels. This study was conducted to investigate hydrolytic stability of modified UF resins as a way of lowering the formaldehyde emission of cured UF resin. Neat UF resins with three different formaldehyde/urea (F/U) mole ratios (1.4, 1.2, and 1.0) were modified, after resin synthesis, by adding four additives such as sodium hydrosulfite, sodium bisulfite, acrylamide, and polymeric 4,4′‐diphenylmethane diisocyanate (pMDI). All additives were added to UF resins with three different F/U mole ratios before curing the resin. The hydrolytic stability of UF resins was determined by measuring the mass loss and liberated formaldehyde concentration of cured and modified UF resins after acid hydrolysis. Modified UF resins of lower F/U mole ratios of 1.0 and 1.2 showed better hydrolytic stability than the one of higher F/U mole ratio of 1.4, except the modified UF resins with pMDI. The hydrolytic stability of modified UF resins by sulfur compounds (sodium bisulfate and sodium hydrosulfite) decreased with an increase in their level. However, both acrylamide and pMDI were much more effective than two sulfur compounds in terms of hydrolytic stability of modified UF resins. These results indicated that modified UF resin of the F/U mole ratio of 1.2 by adding acrylamide was the most effective in improving the hydrolytic stability of UF resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. V

The effects of posttreatments of particleboard adhesive‐type urea–formaldehyde resins were studied. The resins were synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.40, 1.60, 1.80, 2.10, and 2.40 and then the second urea was added to give a final formaldehyde/urea ratio of 1.15 in alkaline pH. The resins were posttreated at 60°C for up to 13.5 h and the 2.5‐h heat‐treated resin samples were stored at room temperature for up to 27 days. Resins sampled during the posttreatments were examined by ¹³C‐NMR and evaluated by bonding particleboards. In the posttreatments, hydroxymethyl groups on the polymeric resin components dissociated to formaldehyde and reacted with the second urea, and methylene and methylene–ether groups were formed from reactions involving the second urea. Methylene–diurea and urea groups bonded to UF polymers were identified. As a result, the viscosity of the resins initially decreased but later increased along with the cloudiness of the resins. Bond‐strength and formaldehyde‐emission values of particleboard varied with posttreatment variables as well as with the F/U₁ mol ratios used in the resin syntheses. The results would be useful in optimizing resin synthesis and handling parameters. Various reaction mechanisms were considered. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1896–1917, 2003     

The effect of alkyd resins on the properties of AA‐NC semi‐IPNs as binders in wood finish

Wood coatings of AA‐NC semi‐interpenetrating polymer networks (semi‐IPNs), made from acid curing amino‐alkyd resins (AA) and nitrocellulose (NC), were prepared by sequential polymerization method. To investigate the effects of oil length on the properties of AA‐NC semi‐IPNs, three grades of alkyd resins (Alkyd) containing 38, 48, and 58% oil were synthesized with phthalic anhydride, glycerol, and soybean oil, employing alcoholysis method. The butylated urea formaldehyde resin (UF) and melamine formaldehyde resin (MF) were also prepared in this study. The AA‐NC semi‐IPNs were maintained at a weight ratio of AA : NC of 25 : 75, where the AA was the composition of MF : UF : Alkyd of 7.5 : 22.5 : 70 (by weight), and 10% of p‐toluene sulfonic acid solution (concentration, 25% in isopropyl alcohol) based on the weight of amino resins was added as acid catalyst. The properties of coatings such as viscosity, drying time, and gel time, and the properties of films including adhesion, hardness, abrasion resistance, impact resistance, tensile strength, released formaldehyde, lightfastness, solvent resistance, and durability were examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1923–1927, 2004     

Low addition of melamine salts for improved melamine‐urea‐formaldehyde adhesive water resistance

The addition of melamine acetate salts to an adhesive glue mix can allow the use of melamine–urea–formaldehyde (MUF) resins of lower melamine contents (rather than just urea–formaldehyde resins) and lower total amounts of melamine. Performances can be obtained that are characteristic of the top‐of‐the‐line, generally higher melamine content MUF adhesive resins for the preparation of wood particleboard panels. Improvements in the panel internal‐bond strength of greater than 30% can be obtained by the addition of melamine acetate salts to top‐of‐the‐line MUF resins. The approach to the concept of increased melamine solubility with a melamine salt is compatible with the approach of increasing melamine solubility with solvents such as acetals (e.g., methylal). However, the synergy advantage of using the two approaches jointly is not very marked. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 287–292, 2003     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. IV

Typical particleboard wood‐adhesive urea–formaldehyde (UF) resins, synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.80, 2.10, and 2.40 and the second urea added to an overall F/U ratio of 1.15, in weak alkaline pH, were allowed to stand at room temperature over a period of 50 days. ¹³C‐NMR of time samples taken over the storage period showed gradual migration of hydroxymethyl groups from the polymeric first‐urea components to the monomeric second‐urea components and also an advancing degree of polymerization of resins by forming methylene and methylene ether groups involving the second urea. These phenomena that varied with the F/U₁ mol ratios used in the resin syntheses due to the varying polymer branching structures resulted in the first step of resin synthesis. Varying viscosity decreases and increases of the resins also occurred. Due to these chemical and physical changes, the particleboards that bonded with the sampled resins showed varying bond strength and formaldehyde‐emission values, indicating process optimizations possible to improve bonding and formaldehyde‐emission performances. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1155–1169, 2001     

Morphology and chemical elements detection of cured urea–formaldehyde resins

As a part of understanding the hydrolysis of cured urea–formaldehyde (UF) resins that has been known as responsible for the formaldehyde emission, leading to sick building syndrome, this study attempted to investigate the morphology and to detect chemical elements of the cured UF resins of different formaldehyde/urea (F/U) mole ratios and hardener (NH₄Cl) levels, using field emission‐scanning electron microscopy and energy‐dispersive spectroscopy. Cured UF resins of low F/U mole ratio showed spherical structure whose diameter increased with an increase in the hardener level, whereas this was not observed for high F/U mole ratio UF resins regardless of the hardener levels. The energy‐dispersive spectroscopy results showed five different chemical elements such as carbon, nitrogen, oxygen, chloride, and sodium in cured UF resins. The chloride distribution assumed as the presence of residual acid in the cured UF resins suggested that the hydrolysis of cured UF resins could initiate at the sites of chlorides on the surface of the spherical structures. As the hardener level increased, the quantities of both carbon and oxygen decreased, whereas those of nitrogen and chloride increased as expected. But the quantity of sodium was within measurement error. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Melamine‐bridged alkyl resorcinol modified urea–formaldehyde resin for bonding hardwood plywood

A powdery product was obtained by the reaction of methylolated melamine with alkyl resorcinols to form melamine‐bridged alkyl resorcinols (MARs). The effects of the addition of this powder on the bonding strength and formaldehyde emission of urea–formaldehyde (UF) resins were investigated. Three types of UF resins with a formaldehyde/urea molar ratio of 1.3 synthesized by condensation at pH 1.0 (UF‐1.0), pH 4.5 (UF‐4.5), and pH 5.0 (UF‐5.0) were fabricated. The addition of MAR to UF‐4.5 and UF‐5.0 for bonding hardwood plywood enhanced the bonding strength and reduced formaldehyde emission. For UF‐1.0, the addition of MAR adversely affected the bonding strength. However, the UF‐1.0 resin yielded the lowest formaldehyde emission of all of the UF resins in the study. The effects of the MAR addition were related to the molecular structures of the UF resins. UF‐1.0 contained a large amount of free urea, a considerable number of urons, and a highly methylene‐linked, ring‐structured higher molecular weight fraction and had a smaller number of methylol groups. Therefore, the addition of MAR was considered to cause a shortage of the methylol groups, which in turn, led to incomplete resin curing. In contrast to UF‐1.0, UF‐5.0 contained a smaller amount of free urea and a linearly structured higher molecular weight fraction and had a larger number of methylol groups. In this case, MAR was considered to effectively react with the methylol groups to develop a three‐dimensional crosslinked polymer network to enhance the bonding strength and suppress the generation of free formaldehyde to reduce formaldehyde emission. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Determination of formaldehyde/urea molar ratio in amino resins by near‐infrared spectroscopy

New processes for synthesis of urea‐formaldehyde (UF) and melamine‐fortified urea‐formaldehyde (mUF) resins have been developed in the last years, motivated by the current concerns about the effects of formaldehyde on human health. All these formulations are quite susceptible to possible operation error, which can significantly influence the characteristics of the final product. The main objective of this work was to implement chemometric techniques for off‐line monitoring of the product's formaldehyde/urea (F/U) molar ratio using near infrared (NIR) spectroscopy. This allows the timely implementation of the necessary corrections in case the product is off‐specification. Calibration models for F/U molar ratio were developed taking into account the most relevant spectral regions for these resins, individually or in combination (7502–6098 cm^?1 and 5000–4246 cm^?1) and using different preprocessing methods. When the appropriate spectral range and preprocessing methods are selected, it is possible to obtain calibration models with high correlation values for these resins. The best preprocessing methods were identified for three cases: UF resin (produced by strongly‐acid process), mUF resin (alkaline‐acid process), and a combined model that involves both UF and mUF resins. It was concluded that significantly better accuracy is obtained when a new model is developed for each particular resin system. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Rheometry of aging of colloidal melamine–urea–formaldehyde polycondensates

Aged and whitened melamine–urea–formaldehyde (MUF) resins in a colloidal state were tested with parallel‐plate rheometry to determine the extent of their viscoelastic behavior. Only in advanced colloidal states, and so only when aggregated colloidal clusters occurred, did the resins present clear indications of viscoelastic responses, as illustrated by the crossover of elastic modulus and viscous modulus curves at lower strain percentages. These colloidal clusters were labile microstructures, which, broken by applied shear, justified the known thixotropic behavior of these resins sufficiently advanced by aging or other means. MUF resins already in the colloidal state, but for which colloidal clustering had not yet occurred, behaved exclusively as viscous liquids. Two different cases of physical gelation were observed, reversible physical gelation and irreversible physical gelation, underlying which a true gel situation possibly occurred. Physical gelation due to colloidal superstructures occurred in both, but the difference in the resin average molecular masses revealed if the physical gelation was reversible or irreversible and, therefore, if the liquid/cluster separation was defined as the terminal phase of physical gelation. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 655–659, 2005     

Examination of selected synthesis parameters for typical wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. II

A particleboard adhesive‐type urea–formaldehyde (UF) resin was made at a formaldehyde ratio of 2.10 and added with a second urea at low temperature to the typical final formaldehyde/urea ratio of 1.15. Time samples taken during heat treatments of the resin sample up to 70°C over a period of 250 min showed decreases in Type II/IIi hydroxymethyl group content, accompanied with decreases in resin sample viscosity and increases in formaldehyde emission of bonded particleboards. The results indicate that various hydroxymethyl groups of polymeric UF resin components migrate to the second urea to form Type I hydroxymethyl groups. Time samples taken during the room‐temperature storage of the resin sample over a period of 1 month behaved similarly initially, but in the later stage, some polymerization progressed, shown by increases in viscosity and methylene and methylene–ether group contents. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1243–1254, 2000     

Reactivity,chemical structure,and molecular mobility of urea–formaldehyde adhesives synthesized under different conditions using FTIR and solid‐state 13C CP/MAS NMR spectroscopy

This study was conducted to investigate the effects of reaction pH condition and hardener type on the reactivity, chemical structure, and molecular mobility of urea–formaldehyde (UF) resins. Three different reaction pH conditions, such as alkaline (7.5), weak acid (4.5), and strong acid (1.0), were used to synthesize UF resins, which were cured by adding four different hardeners (ammonium chloride, ammonium sulfate, ammonium citrate, and zinc nitrate) to measure gel time as the reactivity. FTIR and ¹³C‐NMR spectroscopies were used to study the chemical structure of the resin prepared under three different reaction pH conditions. The gel time of UF resins decreased with an increase in the amount of ammonium chloride, ammonium sulfate, and ammonium citrate added in the resins, whereas the gel time increased when zinc nitrate was added. Both FTIR and ¹³C‐NMR spectroscopies showed that the strong reaction pH condition produced uronic structures in UF resin, whereas both alkaline and weak‐acid conditions produced quite similar chemical species in the resins. The proton rotating‐frame spin–lattice relaxation time (T_1ρH) decreased with a decrease in the reaction pH of UF resin. This result indicates that the molecular mobility of UF resin increases with a decrease in the reaction pH used during its synthesis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2677–2687, 2003     

Production of melamine fortified urea‐formaldehyde resins with low formaldehyde emission

Melamine can be incorporated in the synthesis of urea‐formaldehyde (UF) resins to improve performance in particleboards (PB), mostly in terms of hydrolysis resistance and formaldehyde emission. In this work, melamine‐fortified UF resins were synthesized using a strong acid process. The best step for melamine addition and the effect of the reaction pH on the resin characteristics and performance were evaluated. Results showed that melamine incorporation is more effective when added on the initial acidic stage. The condensation reaction pH has a significant effect on the synthesis process. A pH below 3.0 results on a very fast reaction that is difficult to control. On the other hand, with pH values above 5.0, the condensation reaction becomes excessively slow. PBs panels produced with resins synthesized with a condensation pH between 4.5 and 4.7 showed good overall performance, both in terms of internal bond strength and formaldehyde emissions. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012