Synthesis and characterization of a copolymer: Poly(aniline‐co‐fluoroaniline)

In the present article, we report the chemical synthesis and characterization of poly(aniline‐co‐fluoroaniline) [poly(An‐FAn)]. The copolymerization of aniline and 2‐fluoroaniline was carried out by chemical method in acidic medium. The characterization of poly(aniline‐co‐fluoroaniline) was done using FTIR, UV‐visible spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron micrography (SEM), and a four‐points‐probe conductivity method. X‐ray diffraction (XRD) and SEM characterization reveal crystalline nature of doped copolymer compared to undoped copolymer. The observed decrease in the conductivity of the copolymer relative to polyaniline is attributed to the incorporation of the fluoro moieties into the polyaniline chain. The chemically synthesized copolymer shows good solubility in common organic solvents, and is, therefore, technological useful. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1460–1466, 2001     

Fabrication,characterization, and properties of poly(ethylene‐co‐vinyl acetate)/magnetite nanocomposites

Poly(ethylene‐co‐vinyl acetate) (EVA)/magnetite (Fe₃O₄) nanocomposite was prepared with different loading of Fe₃O₄ nanoparticles. The mixing and compounding were carried out on a two‐roll mixing mill and the sheets were prepared in a compression‐molding machine. The effect of loading of nanoparticles in EVA was investigated thoroughly by different characterization technique such as transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), limiting oxygen index (LOI), and technological properties. TEM analysis showed the uniform dispersion of filler in the polymer matrix and the dispersion of filler decreased with increase in filler content. XRD of the nanocomposite revealed the more ordered structure of the polymer chain. An appreciable increase in glass transition temperature was observed owing to the restricted mobility of Fe₃O₄‐filled EVA nanocomposite. TGA and flame resistance studies indicated that the composites attain better thermal and flame resistance than EVA owing to the interaction of filler and polymer segments. Mechanical properties such as tensile strength, tear resistance, and modulus were increased for composites up to 7 phr of filler, which is presumably owing to aggregation of Fe₃O₄ nanoparticle at higher loading. The presence of Fe₃O₄ nanoparticles in the polymer matrix reduced the elongation at break and impact strength while improved hardness of the composite than unfilled EVA. The change in technological properties had been correlated with the variation of polymer–filler interaction estimated from the swelling behavior. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40116.     

Synthesis and characterization of sPS/montmorillonite nanocomposites

The present work analyzed the possibility of obtaining and producing syndiotactic polystyrene (sPS)–based nanocomposites. The work first focused on possible technology to use for intercalation from solution and melt intercalation. Using a blend of sPS with atactic polystyrene (aPS) as the matrix was also considered. Thermal analysis techniques, such as differential scanning calorimetry (DSC) and thermogravimetry (TGA), were used to study the thermal properties and stability of the nanocomposites obtained and to select the most appropriate nanocharges. The effect of the introduction of nanofillers on these properties also was evaluated. X–ray diffraction was used to investigate the degree of clay exfoliation. Finally, mechanical characterization of the nanocomposites obtained was performed and compared to that of the pure material. The tests demonstrated that nanodispersion of phyllosilicate layers improved the mechanical behavior of the polymers analyzed, especially the annealed sPS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4957–4963, 2006     

Effect of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide on liquid oxygen compatibility of bisphenol a epoxy resin

In this study, bisphenol A epoxy resin (DGEBA) was chemically modified by 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO), and the molecular structure of the modified epoxy resin was characterized by Fourier transform infrared spectra. The effects of DOPO on liquid oxygen compatibility of DGEBA were calculated using mechanical impact method. The results indicated that epoxy resin (EP‐P1)/4,4‐diaminobisphenol sulfone (DDS) was compatible with liquid oxygen. When compared with EP/DDS, differential scanning calorimetry and thermogravimetry analyses showed that EP‐P1/DDS and EP‐P2/DDS had much higher glass transition temperatures and char yield. X‐ray photoelectron spectroscopic analysis suggested that phosphorus atoms on the surface of EP‐P1/DDS and EP‐P2/DDS could act in the solid phase to restrain the incompatible reaction, which was in accordance with the flame‐retardant mechanism of phosphorus‐containing compounds. The compatibility mechanism of EP‐P1/DDS was further proposed. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40848.     

Preparation and characterization of low molecular weight silk fibroin by high‐temperature and high‐pressure method

A low molecular weight silk fibroin powder (LMSF) was prepared through high temperature (200°C) and high pressure (20 kgf/cm²), without any addition of chemicals. The carbonized adducts produced during this process were then removed by treatment with activated charcoal. The yield of LMSF by this preparation method was over 60% after the removal of carbonized adducts by using activated charcoal. Amino acid analysis showed an observable decrease in contents of serine and tyrosine in LMSF prepared by this method, as compared to those prepared by neutral salt. The molecular weight of this LMSF was also observably decreased with an increase in the reaction time. From the measurements of differential scanning calorimeter (DSC) and thermal gravimetric analyzer (TGA), thermal properties of LMSF through high temperature and high pressure were also decreased as compared to those produced by neutral salts. In addition, wide‐angle X‐ray diffraction (WAXD) patterns showed that the crystallinity of LMSF differed from that of the original silk fibroin. It can be said that the preparation method of LMSF in this study is a simple, economical, and environmentally compatible process with many advantages. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2890–2895, 2002     

Charge transport mechanism in intercalated polypyrrole aluminum‐pillared montmorillonite clay nanocomposites

Nanocomposites based on intercalated conducting polypyrrole (PPy) into the galleries of inorganic aluminum‐pillared Montmorillonite (Al‐PMMT) clay with varying concentrations of Al‐PMMT were prepared by in situ chemical polymerization. The intercalation was confirmed by X‐ray diffraction pattern. Charge transport mechanism in these composites was investigated by temperature dependent direct current conductivity measurements. An increase in DC conductivity value on addition of (Al‐PMMT) clay in the composites at all temperatures and a transition from three‐dimensional (3D) Mott's variable range hopping (VRH) process in pristine PPy to one‐dimensional (1D) Mott's VRH process in the intercalated polymer composites has been observed. This transition in charge transport mechanism of PPy from 3D VRH to 1D VRH on intercalation has been interpreted in terms of straightening and linearization of polymer chains and decrease in inter‐chain interactions in the intercalated PPy. Enhancement in mechanical properties and increase in thermal stability of the nanocomposites was also observed with the increase in weight percentage of Al‐PMMT in PPy‐Al‐PMMT composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

负载羧基有机蒙脱土制备环氧树脂纳米复合材料

用椰油酰胺丙基甜菜碱(CAB)制备了1种负载羧基的有机蒙脱土,并将这种有机蒙脱土加入甲基四氢苯酐固化环氧树脂体系中制得环氧树脂/蒙脱土纳米复合材料。采用XRD衍射和透射电镜TEM研究了蒙脱土有机化前后和在纳米复合材料中的片层结构和形态。用TGA研究了纳米复合材料的热稳定性能。结果表明,制备的负载羧基蒙脱土充分插层且很容易分散在环氧树脂中得到纳米复合材料。其热稳定性和有机蒙脱土在树脂中的分散状态有关。     

Phosphorus‐containing epoxy resins: Thermal characterization

Three novel aromatic phosphorylated diamines, i.e., bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl} pyromellitamic acid (AP), 4,4′‐oxo bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl}phthalamic acid (AB) and 4,4′‐hexafluoroisopropylidene‐bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl}phthalamic acid (AF) were synthesized and characterized. These amines were prepared by solution condensation reaction of bis(3‐aminophenyl)methyl phosphine oxide (BAP) with 1,2,4,5‐benzenetetracarboxylic acid anhydride (P)/3,3′,4,4′‐benzophenonetetracarboxylic acid dianhydride (B)/4,4′‐(hexafluoroisopropylidene)diphthalic acid anhydride (F), respectively. The structural characterization of amines was done by elemental analysis, DSC, TGA, ¹H‐NMR, ¹³C‐NMR and FTIR. Amine equivalent weight was determined by the acetylation method. Curing of DGEBA in the presence of phosphorylated amines was studied by DSC and curing exotherm was in the temperature range of 195–267°C, whereas with conventional amine 4,4′‐diamino diphenyl sulphone (D) a broad exotherm in temperature range of 180–310°C was observed. Curing of DGEBA with a mixture of phosphorylated amines and D, resulted in a decrease in characteristic curing temperatures. The effect of phosphorus content on the char residue and thermal stability of epoxy resin cured isothermally in the presence of these amines was evaluated in nitrogen atmosphere. Char residue increased significantly with an increase in the phosphorus content of epoxy network. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2235–2242, 2002     

Highly exfoliated nanostructure in trifunctional epoxy/clay nanocomposites using boron trifluoride as initiator

Epoxy/clay nanocomposites based upon a trifunctional epoxy resin, triglycidyl p‐amino phenol (TGAP), have been prepared by intercalating an initiator of cationic homopolymerization, a boron trifluoride monoethylamine (BF₃·MEA) complex, into the montmorillonite clay galleries before the addition of the TGAP and the curing agent, 4,4‐diamino diphenyl sulfone (DDS), and effecting the isothermal curing reaction. The BF₃·MEA enhances the intragallery cationic homopolymerization reaction, which occurs before the extragallery cross‐linking reaction of the TGAP with the DDS, and which hence contributes positively to the mechanism of exfoliation of the clay. The effects of isothermal cure temperature and of BF₃·MEA content have been studied, in respect of both the reaction kinetics, monitored by differential scanning calorimetry, and the nanostructure, as identified by small‐angle X‐ray scattering and transmission electron microscopy. It is shown that the use of BF₃·MEA in this way as an initiator of intragallery homopolymerization significantly improves the degree of exfoliation in the cured nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40020.     

Synthesis and characterization of epoxy based nanocomposites

Epoxy‐clay nanocomposites were synthesized to examine the effects of the content and type of different clays on the structure and mechanical properties of the nanocomposites. Diglycidyl ether of bisphenol‐A (epoxy) was reinforced by 0.5–11 wt % natural (Cloisite Na⁺) and organically modified (Cloisite 30B) types of montmorillonite. SEM results showed that as the clay content increased, larger agglomerates of clay were present. Nanocomposites with Cloisite 30B exhibited better dispersion and a lower degree of agglomeration than nanocomposites with Cloisite Na⁺. X‐ray results indicated that in nanocomposites with 3 wt % Cloisite 30B, d‐spacing expanded from 18.4 Å (the initial value of the pure clay) to 38.2 Å. The glass transition temperature increased from 73°C, in the unfilled epoxy resin, to 83.5°C in the nanocomposite with 9 wt % Cloisite 30B. The tensile strength exhibited a maximum at 1 wt % modified clay loading. Addition of 0.5 wt % organically modified clay improved the impact strength of the epoxy resin by 137%; in contrast, addition of 0.5 wt % unmodified clay improved the impact strength by 72%. Tensile modulus increased with increasing clay loading in both types of nanocomposites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1081–1086, 2005     

Elaboration and thermal analysis of nanocomposites based on poly(methyl methacrylate‐co‐4‐vinylpyridine) and Maghnia bentonite

Nanocomposites based on an organically modified bentonite, from Maghnia Algeria (OBT) and a copolymer of methyl methacrylate with 4‐vinylpyridine (PMM4VP) synthesized in dioxan at room temperature using a neutral Ni(II)α‐benzoinoxime complex as a single component initiator, were elaborated via solution intercalation method and characterized by several techniques. X‐ray diffraction and transmission electron microscopy investigations indicate that mainly exfoliated and intercalated PMM4VP/OBT nanocomposites were elaborated and that the degree of exfoliation decreases with an increase of the OBT loading. Thermal analyses of these nanocomposites compared with their virgin copolymer confirmed a significant improvement of their thermal stability as evidenced by an increase of 28°C in their onset degradation temperatures. In addition, differential scanning calorimetry displayed an increase in the range of 12–18°C in their glass transition temperatures relative to their virgin copolymer. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

环氧树脂／蒙脱土纳米复合材料的制备与性能

重点综述了影响蒙脱土片层在环氧基体中剥离的主要因素。根据环氧树脂／蒙脱土纳米复合材料的结构特点,解释了其力学性能、热性能、耐腐蚀和阻隔性能得到明显改善的原因。     

X‐ray diffraction studies and phase volume determinations in poly(ethylene glycol)–montmorillonite nanocomposites

Poly(ethylene glycol)–montmorillonite nanocomposites were prepared by both solution and melt intercalation methods with a range of polymer molecular weights and at a range of polymer loadings. Particular attention was given to the reliability of low‐angle X‐ray diffraction results for basal plane spacing and a sound correlation between three diffractometers was obtained (±0.005 nm). Expansion of the basal plane spacing from 1.23 nm to 1.82 nm by solution intercalation was independent of polymer molecular weight in the range 300–20 000. Furthermore, the clay expansion was independent of the method of intercalation; melt intercalation also gave d₀₀₁ = 1.82 nm irrespective of polymer molecular weight. The maximum amount of polymer intercalated by clay and the maximum loading of clay that polymer can sustain were also studied for the determination of nanocomposite formulations. The confined polymer exerts a reduced effective density (670 kg m^?3) in the galleries. Copyright © 2005 Society of Chemical Industry     

Preparation and characterization of ethylene vinyl acetate copolymer/montmorillonite nanocomposite

Ethylene vinyl acetate copolymer (EVA) and monmorillonite (MMT) nanocomposites have been investigated as a function of vinyl acetate content and molecular weight of EVA and types of substituted alkyl ammonium of MMT. It is found that vinyl acetate content and type of substituted alkyl ammonium are important factors for the intercalation behaviour of MMT in MMT/EVA nanocomposite. Maleic anhydride grafted high‐density polyethylene was used as a compatibilizer to improve the intercalation behaviour of MMT. X‐ray diffraction and transmission electron microscopy were used to characterize the intercalation/exfoliation behaviour, and mechanical properties were measured. © 2003 Society of Chemical Industry     

Synthesis and characterization of calcium‐containing poly(urethane‐urea)s

A calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)2] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Four different bisureas like hexamethylene bis(ω,N‐hydroxyethylurea), tolylene 2,4‐bis(ω,N‐hydroxyethylurea), hexamethylene bis(ω,N‐hydroxypropylurea), and tolylene 2,4‐bis(ω,N‐hydroxypropylurea) were prepared by reacting ethanolamine or propanolamine with hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI). Calcium‐containing poly(urethane‐urea)s (PUUs) were synthesized by reacting HMDI or TDI with 1:1 mixtures of Ca(HEEP)2 and each of the bisureas using di‐n‐butyltin dilaurate as a catalyst. The PUUs were well characterized by Fourier transform infrared, 1H‐ and 13C‐NMR (nuclear magnetic resonance), solid‐state 13C cross‐polarization–magic angle spinning NMR, viscosity, solubility, elemental, and X‐ray diffraction studies. Thermal properties of the polymers were also studied by using thermogravimetric analysis and differential scanning calorimetry. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3488–3496, 2003     

Structural characterization of hydrophilic polymer blends/montmorillonite clay nanocomposites

The nanocomposite films comprising polymer blends of poly(vinyl alcohol) (PVA), poly(vinyl pyrrolidone) (PVP), poly(ethylene oxide) (PEO), and poly(ethylene glycol) (PEG) with montmorillonite (MMT) clay as nanofiller were prepared by aqueous solution casting method. The X‐ray diffraction studies of the PVA–x wt % MMT, (PVA–PVP)–x wt % MMT, (PVA–PEO)–x wt % MMT and (PVA–PEG)–x wt % MMT nanocomposites containing MMT concentrations x = 1, 2, 3, 5 and 10 wt % of the polymer weight were carried out in the angular range (2θ) of 3.8–30°. The values of MMT basal spacing d₀₀₁, expansion of clay gallery width W_cg, d‐spacing of polymer spherulite, crystallite size L and diffraction peak intensity I were determined for these nanocomposites. The values of structural parameters reveal that the linear chain PEO and PEG in the PVA blend based nanocomposites promote the amount of MMT intercalated structures, and these structures are found relatively higher for the (PVA–PEO)–x wt % MMT nanocomposites. It is observed that the presence of bulky ester‐side group in PVP backbone restricts its intercalation, whereas the adsorption behavior of PVP on the MMT nanosheets mainly results the MMT exfoliated structures in the (PVA–PVP)–x wt % MMT nanocomposites. The crystallinities of the PEO and PEG were found low due to their blending with PVA, which further decreased anomalously with the increase of MMT concentration in the nanocomposites. The decrease of polymer crystalline phase of these materials confirmed their suitability in preparation of novel solid polymer nanocomposite electrolytes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40617.     

Synthesis and characterization of elastomeric polyurethane/clay nanocomposites

An elastomeric polyurethane/clay (PU/clay) nanocomposite based on poly(propylene glycol) (PPG), glycerol propoxylate, and toluene‐diisocyanate (TDI) was synthesized by intercalative polymerization technology. The results of wide angle X‐ray diffraction (WAXD) studies showed that the gallery distance of the clay in the hybrid was enlarged from 1.9 to 4.5nm or more. Introducing clay in the PU matrix resulted in an increase in both the tensile strength and elongation at beak. When the clay content reached about 8%, the tensile strength and elongation at break were two times and five times respectively to that of the pure PU. In addition, the clay intercalative route to the nanocomposite synthesis also effected the thermal properties of the nanocomposites. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1444–1448, 2001     

Synthesis and characterization of sulfonated poly(ethylene terephthalate)/montmorillonite nanocomposites

Sulfonated poly(ethylene terephthalate) (SPET)/montmorillonite nanocomposites were prepared by in situ intercalative polymerization. The microstructure, morphology, and properties of the nanocomposites were studied with wide‐angle X‐ray diffraction, transmission electron microscopy, atomic force microscopy, differential scanning calorimetry, and thermogravimetric analysis. The results indicated that an increase in the ? SO₃Na content improved the dispersion of organically modified montmorillonite in the SPET ionomer matrix, and the dispersed layered silicates in the SPET matrix acted as nucleating agents in SPET crystallization processes and improved the thermal stability of SPET. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1150–1156, 2005     

Preparation and characterization of poly(ethylene terephthalate) copolyesters modified with sodium‐5‐sulfo‐bis‐(hydroxyethyl)‐isophthalate and poly(ethylene glycol)

Two types of poly(ethylene terephthalate) (PET) copolyesters were successfully prepared with sodium‐5‐sulfo‐bis‐(hydroxyethyl)‐isophthalate (SIPE) and poly(ethylene glycol) (PEG) units with different molecular weights named as cationic dyeable polyester and easy cationic dyeable polyester. Their chemical and crystalline structures were characterized by the nuclear magnetic resonance (NMR), wide angle X‐ray diffraction (WAXD), and small angle X‐ray scattering measurement, and their thermal properties were tested by differential scanning calorimetry and thermogravimetric analysis, respectively. NMR experimental results showed that the actual molar ratio of comonomers was basically consistent with the correlative feed ratio. WAXD results indicated that the crystalline structures of prepared copolyesters were similar to that of PET. Moreover, the glass transition temperature, melting temperature, and thermal degradation temperature were found to decrease with the reduction of the of PEG units as the incorporation of lower of PEG units brought more ether bonds into molecular chains, which increased the irregularity of molecular chain arrangement and led to lower crystallinity. In addition, because the incorporation of PEG units with lower molecular weight led to more ether bonds and hydroxyl end‐groups in molecular chains, the value of contact angle of PET copolyesters dropped, manifesting PET copolyesters had better hydrophilicity with the decreasing molecular weight of PEG units.© 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39823.     

Synthesis and characterization of novel poly(o‐toluidine) montmorillonite nanocomposites: Effect of surfactant on intercalation

The investigation of clay based polymer nanocomposites has opened the door for the development of novel, ecofriendly advanced nano materials that can be safely recycled. Because of their nanometer size dispersion, these nanocomposites often have superior physical and mechanical properties. In this study, novel nanocomposites of poly(o‐toluidine) (POT) and organically modified montmorillonite (MMT) were synthesized using camphor sulfonic acid (CSA), cetyl pyridinum chloride (CPCl), and N‐cetyl‐N,N,N‐trimethyl ammonium bromide (CTAB) to study the role of surfactant modification on the intercalation. The in situ intercalative polymerization of POT within the organically modified MMT layers was analyzed by FTIR, UV–visible, XRD, SEM as well as TEM studies. The average particle size of the nanocomposites was found to be in the range 80–100 nm. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007