Polyurethane dispersions derived from polycarbonatediols and m‐di(2‐isocyanatopropyl)benzene

Aqueous polyurethane dispersions derived from various polycarbonatediols, m‐di(2‐isocyanatopropyl)benzene(TMXDI), and various carboxylic diols including dimethylol propionic acid (DMPA), dimethylol butyric acid (DMBA), and a carboxylic polycaprolactonediol (Placcel 205BA) were prepared by a method in which the dispersing procedure was modified to enhance the molecular weight. The NH₂/NCO ratio during chain extension affected the molecular weight of the polyurethanes, significantly, and an optimum ratio of 0.67:1.0 was used. The molecular weight, particle size, tensile properties, and thermal properties of the polyurethane dispersions were investigated. The effect chemical structure of the polycarbonatediols on the properties shows no obvious trend, but the polyurethane dispersions derived from the carboxylic polycaprolactonediol exhibit smaller particle size and softer tensile properties when compared with those derived from DMPA and DMBA. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Effect of composition on aqueous polyurethane dispersions derived from polycarbonatediols

Aqueous polyurethane dispersions derived from isophorone diisocyanate, various polycarbonatediols of different molecular weights, and dimethylol butyric acid were prepared by a dispersing procedure modified to enhance molecular weight. Particle size, average molecular weight, and tensile properties were determined. The molar ratio of reactants affected the properties of the polyurethane dispersions significantly, with the trends described as the effects of their ionic group and polycarbonatediol soft‐segment contents. The molecular weight of the polycarbonatediols also significantly affected the particle size of the aqueous polyurethane dispersions and the film properties. As the molecular weight of the polycarbonatediols decreased, the particle size of the aqueous polyurethane dispersions decreased, and the moduli of the cast films increased, as expected. However, the tensile strength of the cast films decreased as the molecular weight of the polycarbonatediols decreased because of the decrease in elongation at break. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4419–4424, 2006     

Aqueous polyurethane dispersions derived from polycarbonatediols and Di(4‐isocyanatocyclohexyl)methane

Aqueous polyurethane dispersions derived from various polycarbonatediols, di(4‐isocyanatocyclohexyl)methane (HMDI), and various carboxylic diols, including dimethylol propionic acid (DMPA), dimethylol butyric acid (DMBA), and a carboxylic polycaprolactonediol, were prepared by a method in which the dispersing procedure was modified to enhance the molecular weight. The molecular weight, particle size, tensile properties, thermal properties, and dynamic mechanical properties of the polyurethane dispersions were investigated. The dynamic mechanical property data indicate that these polyurethane dispersions can exhibit higher temperature resistance when compared with those derived from isophorone diisocyanate (IPDI). POLYM. ENG. SCI. 46:588–593, 2006. © 2006 Society of Plastics Engineers     

Clear polyurethane dispersions of nanometer size derived from carboxylic polycaprolactonediols

Aqueous polyurethanes dispersions of nanometer size derived from various carboxylic polycaprolactonediols of different molecular weights, carboxylic diols, including 2,2‐di(hydroxymethyl)propanoic acid (DMPA), 2,2‐di(hydroxymethyl)butanoic acid (DMBA), and di(4‐isocyanatocyclohexyl)methane (HMDI) were prepared by a method in which the dispersing procedure was modified to enhance the molecular weight. The molecular weight, particle size, and UV–vis spectra of the polyurethane dispersions were investigated. The tensile properties of the cast films were determined. The modified dispersing procedure gave polyurethane dispersions with higher molecular weight and better tensile strength. As the molecular weight of the carboxylic polycaprolactonediol decreases, the content of the ionic groups increases, the particle size decreases accordingly. As the molecular weight of the carboxylic polycaprolactonediol used is 1000 g/mol or below, the polyurethanes dispersions become completely clear. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of TDI and FA‐703 on physico‐mechanical properties of polyurethane dispersion

A series of water dispersion polyurethanes dispersions (PUDs) were prepared by polyaddition reaction using isophorone diisocyanate (IPDI), toluene diisocyanate (TDI), poly(oxytetramethylene) glycol (PTMG), dimethylol propionic acid (DMPA), and triol (trade name FA‐703). Various formulations were designed to investigate the effects of process variables such as TDI and FA‐703 on the physico‐mechanical properties of PUD. IR spectroscopy was used to check the end of polymerization reaction and characterization of polymer. Evolution of the particle size distribution, contact angle, T_g, molecular weight, viscosity, and mechanical properties of the emulsion‐cast films were significantly affected by variable content of TDI and FA‐703. Average particle size of the prepared polyurethane emulsions and contact angle decrease with increase of content of FA‐703 and TDI. Molecular weight, T_g, tensile strength, tear strength, hardness, viscosity and elongation at break increase with increase of content of FA‐703 and TDI. The increase of molecular weight, tensile strength, tear strength and elongation at break properties are interpreted in terms of increasing hard segments, chain flexibility, and phase separation in high content of FA‐703 and TDI‐based polyurethane. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of Diisocyanate Structure on the Synthesis and Properties of Ionic Polyurethane Dispersions

A number of aqueous polyurethane dispersions based on polytetramethylene glycol (PTMG), 1,4-butanediol (1,4-BDO), dimethylol propionic acid (DMPA) and diisocyanates of differing structures such as toluene diisocyanate (TDI), diphenylmethane diisocyanate (MDI), isophorone diisocyanate (IPDI), and dicyclohexylmethane diisocyanate (H₁₂MDI) were prepared. IR Spectroscopy was used to check the end of polymerization reaction and also the polymer characterization. The effects of diisocyanate structure on the particle size, contact angle, mechanical and thermal properties of the emulsion-cast films were studied. Average particle size of prepared polyurethane emulsions change by different diisocyanate based polyurethane. TDI based PU shows higher average particle size and contact angle than the others. Tensile strength, hardness, and elongation at break were higher in the case of MDI based polyurethane. Thermal property and thermal stability is also affected by variation of diisocyanate molecular structure.     

Waterborne anionomeric polyurethane–ureas from functionalized fluoropolyethers

A family of anionomeric segmented polyurethane–ureas made from α‐ω dimethylol‐terminated perfluoropolyethers (M_n = 1000–2000), isophorone diisocyanate, dimethylol propionic acid, and ethylenediamine was obtained in form of stable aqueous dispersions. The dispersions were characterized by viscometry and dynamic laser light scattering. The main compositive parameters explored were the amount of COOH groups and the length of the fluorinated macromer. The new polyurethane–ureas were characterized by dynamic mechanical analysis obtaining information on modulus, thermal transition, and phase segregation. Surface properties and chemical resistance were estimated through measurements of static contact angles and spot tests with different solvents. Although surface hydrophobicity was not affected by composition, water‐sorption behavior was sensitive to the ionic character (COOH level) of the polymer. Diffusion and permeability coefficients of polymer films, having different carboxyl contents, were estimated. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 136–144, 2004     

Synthesis and properties of aqueous polyurethane dispersions: Influence of molecular weight of polyethylene glycol

Aqueous polyurethane dispersions (PUDs) have recently emerged as important alternatives to their solvent-based counterparts for various applications due to increasing health and environmental awareness. A series of aqueous polyurethane dispersions containing carboxylate anion as hydrophilic pendant groups were synthesized through step growth polymerization reaction using hexamethylene diisocyanate (HDI), 1,4-butanediol (1,4-BDO), dimethylol propionic acid (DMPA) and polyethylene glycol (PEG) of different molecular weight. Effect of PEG molecular weight was investigated on molecular structure, contact angle measurement, and physical and adhesive properties of PU emulsions. Fourier transform infrared spectroscopy (FT-IR) was used to check the completion of polymerization reaction. Contact angle measurement indicated that the hydrophilicity of polymer increases by increasing molecular weight of PEG with a corresponding decrease in contact angle. Results of T-peel test showed a decrease in peel strength by increasing molecular weight of PEG. Moreover, solid contents%, drying time and storage stability suggested fast drying properties and greater stability of aqueous PU dispersions.     

Preparation,mechanical properties of waterborne polyurethane and crosslinked polyurethane‐acrylate composite

The waterborne polyurethane (PU) prepolymer was first prepared based on isophorone diisocyanate, polyether polyol (NJ‐210), dimethylol propionic acid (DMPA), and hydroxyethyl methyl acrylate via in situ method. The crosslinked waterborne polyurethane‐acrylate (PUA) dispersions were prepared with the different functional crosslinkers. The chemical structures, optical transparency, and thermal properties of PU and PUA were confirmed by Fourier transform infrared spectrometry, ultraviolet–visible spectrophotometry, and differential scanning calorimetry. Some physical properties of the aqueous dispersions such as viscosity, particle size, and surface tension were measured. Some mechanical performances and solvent resistance of PUA films were systemically investigated. The experimental results showed that the particle sizes of the crosslinked PUA aqueous dispersions were larger than the PU and increased from 57.3 to 254.4 nm. When the ratios of BA/St, BA/TPGDA, and BA/TMPTA were 70/30, PUA films exhibited excellent comprehensive mechanical properties. The tensile strength and elongation at break of the film were 2.17 MPa and 197.19%. When the ratio of BA/St was 30/70, the film had excellent water resistance and was only 6.47%. The obtained PUA composites have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings, and wood finishes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and property of waterborne UV‐curable chain‐extended polyurethane surface sizing agent: Strengthening and waterproofing mechanism for cellulose fiber paper

Waterborne UV‐curable polyurethane (UWPU) dispersions with different hydrophilicity and functionalities were prepared by varying the content of dimethylol butanoic acid (DMBA) and pentaerythritol triacrylate (PETA). And linear and cyclic chain extenders with different functionalities were also incorporated into the UWPU backbone, including isophorone diamine (IPDA), diethylene triamine (DETA), and ethylene diamine (EDA). Effects of DMBA content, PETA content, photoinitiator content, UV curing time, chain extender on the properties of UWPU dispersions and films, as well as the properties of the unsized and sized paper were investigated. The water resistance and mechanical properties of sized paper were greatly relied on the particle size, the molecular weight, the croslinking density, and penetrability of UWPU. UWPU dispersion chain extended with IPDA (IPDA‐UWPU) displayed smaller particle size than that of UWPU. The paper sized with IPDA‐UWPU was endowed with best water resistance, tensile strength, folding strength and surface strength. XPS depth analysis revealed that IPDA‐UWPU exhibited better penetrability into the paper substrate than UWPU. SEM and AFM demonstrated that the smoothness of sized paper was improved, and the bond strength between fibers was enhanced. The obtained UWPU could be directly used as an effective and fast drying surface sizing agent for cellulose fiber paper. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42354.     

Effect of ionic content,solid content,degree of neutralization,and chain extension on aqueous polyurethane dispersions prepared by prepolymer method

There are many variables in the preparation of aqueous polyurethane (PU) dispersions. Carboxylic acid content, solid content, degree of pre/postneutralization of the carboxylic acids, and chain extension all impact dispersion particle size, viscosity, pH, molecular weights, and glass transition temperature. This study evaluated the impact of these variables on a given PU dispersion formulation prepared from isophorone diisocyanate, an aliphatic polyester polyol, dimethylol propionic acid, and hexamethylene diamine with triethyl amine as the neutralizing base and N‐methyl pyrrolidone as the cosolvent. Changes in carboxylic acid content, degree of preneutralization, and chain extension were found to have the expected impacts on dispersions properties. Increased ionic content in the dispersion step led to lower particle size and higher viscosity, increased chain extension with its concurrent increase in molecular improved subsequent film properties. Surprising results were obtained by varying the amount of postneutralization and from increased solids content at the time of dispersion. Unexpectedly, both of these variations led to much higher dispersion viscosities and particle size in solution. To have these changes take place, it is theorized that there is a major change in solution morphology caused by these modifications. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2514–2520, 2005     

Preparation and properties of polydimethylsiloxane (PDMS)/polytetramethyleneadipate glycol (PTAd)-based waterborne polyurethane adhesives: Effect of PDMS molecular weight and content

Waterborne polyurethane (WBPU) dispersions were prepared by pre-polymer process using siloxane polyol, namely polydimethylsiloxane (PDMS), and polyester polyol, namely poly(tetramethyleneadipate glycol) (PTAd), as a soft segment. Three different molecular weights (M_n = 550, 6000, 110,000) of PDMS and one fixed molecular weight of PTAd (M_n = 2000) was used during preparation of WBPU dispersions. This research aims to explore the potential use of PDMS in complementing WBPU by boosting flexibility, water resistance, and adhesive strength. The water swelling (%), tensile strength, and adhesive strength of WBPUs were investigated with respect to PDMS molecular weight and PDMS content (PDMS mol %). The water swelling (%) and tensile strength decreased with increasing PDMS molecular weight at a fixed PDMS content (mol %) in mixed polyol of WBPU films. By contrast, the peel adhesive strength peaked at 6.64 mol % and 4.43 mol % with molecular weight of PDMS at 550 and 6000, respectively, while it only decreased when the molecular weight of PDMS stood at 110,000. The adhesive strength was almost unaffected with optimum content (6.64 mol %) of lower PDMS molecular weight (M_n = 550) in mixed polyol-based WBPU after immersing the adhesive bonded nylon fabrics in water for 48 h among all of the samples. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and properties of block and graft waterborne polyurethane modified with α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane and α‐N,N‐dihydroxyethylaminopropyl‐ω‐butylpolydimethylsiloxane

In this study, α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane and α‐N,N‐dihydroxyethylaminopropyl‐ω‐butylpolydimethylsiloxane were used to prepare block and graft waterborne polyureathane–polysiloxane copolymer dispersions. α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane was synthesized by hydrosilylation, methoxylation and equilibrium reactions; α‐N,N‐dihydroxyethylaminopropyl‐ω‐butylpolydimethylsiloxane was synthesized via hydroxyl protection, alkylation, anionic ring‐opening polymerization, hydrosilylation, and deprotection. Block and graft waterborne polyurethane–polysiloxane copolymer dispersions were prepared by the reaction of poly(propylene glycol) (PPG), toluene diisocyanate (TDI), 2,2‐dimethylol propionic acid (DMPA), 1,4‐butanediol (BDO), α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane, and α‐N,N‐dihydroxy‐ethylaminopropyl‐ω‐butylpolydimethylsiloxane. The water absorption of block and graft waterborne polyurethane–polysiloxane copolymer films decreased from 163.9 to 40.2% and 17.3%, respectively, when percent of polysiloxane (w/w) increased from 0 to 5%, and the tensile strength of the block waterborne polyurethane–polysiloxane copolymer films decreased while the tensile strength of graft waterborne polyurethane–polysiloxane copolymer films increased with increase of percent of polysiloxane. For graft waterborne polyurethane–polysiloxane films, the tensile strength would decrease when percent of polysiloxane was more than 3%. POLYM. ENG. SCI., 54:805–811, 2014. © 2013 Society of Plastics Engineers     

Aqueous dispersion of polyurethanes from H12MDI,PTAd/PPG,and DMPA: Particle size of dispersion and physical properties of emulsion cast films

Aqueous dispersions of ionic/nonionic polyurethane (PU) were prepared from hydrogenated diphenylemthane diisocyanate (H₁₂MDI), poly(tetramethylene adipate) glycol (PTAd), polypropylene glycol (PPG), monofunctional ethylene-propylene oxide ether, and dimethylol propionic acid (DMPA). The effects of DMPA, PTAd/PPG ratio, and the average molecular weight of PPG on the state of dispersion, mechanical, and viscoelastic properties of the emulsion cast films were determined using Authosizer, Instron, and Rheovibron.     

Polyurethane ionomer dispersions from a blocked aromatic‐diisocyanate prepolymer

Aqueous anionic blocked aromatic polyurethane prepolymers were synthesized by a prepolymer mixing process and their dispersions were obtained by adding water to the blocked prepolymer solutions. A series of prepolymers were prepared by using toluene 2,4‐diisocyanate, 4,4′‐diphenylmethane diisocyanate, polytetramethylene glycol, dimethylol propionic acid, methyl ethyl ketoxime and ε‐caprolactam. The aqueous dispersions were characterized by Fourier‐transform infrared spectroscopy, gel permeation chromatography, differential scanning calorimetry and thermogravimetric analysis. The particle sizes, viscosities, pH and storage stabilities of the dispersions were studied and compared. Some mechanical properties of the cast films obtained from the aqueous dispersions and the adhesive properties of the dispersions were also evaluated. Copyright © 2004 Society of Chemical Industry     

Properties of Waterborne Polyurethane Adhesives with Aliphatic and Aromatic Diisocyanates

A series of waterborne polyurethane (WBPU) adhesives were prepared with various ratios of aliphatic/aromatic diisocyanates, namely 4,4′-dicyclohexylmethane diisocyanate (H₁₂MDI) as an aliphatic diisocyanate and 4,4′-diphenylmethane diisocyanate (MDI) as an aromatic diisocyanate with poly(tetramethyleneoxideglycol) (PTMG), ethylene diamine (EDA) and dimethylol propionic acid (DMPA). ¹H-NMR spectroscopy was utilized to investigate the side reaction at the dispersion step during synthesis of WBPU dispersions with respect to aliphatic, aromatic and mixed diisocyanates. The tensile strength, Young's modulus, elongation at break (%), storage modulus, glass transition temperature and adhesive strength were measured with respect to aliphatic/aromatic diisocyanate contents. The adhesive strength was maximum using mixed diisocyanates containing 25 mol% MDI in WBPU adhesives.     

Emulsifyable air drying urethane alkyds

A novel monomer, acrylamido (A) tertiary (T) butane (B) sulfonic (S) acid (ATBS) a commercially available ionic moiety was used as a replacement of dimethylol propionic acid (DMPA) in synthesis of polyurethane dispersion. IR technique was used to confirm the chemical structure and formation of polyurethane dispersions. Polyurethane dispersions were investigated for various coating properties, such as drying times, pencil hardness, adhesion, chemical and solvent resistance. Polyurethane dispersion based on ATBS showed better thermal, chemical and coating properties than those prepared by DMPA anionomer.     

羧酸型水性聚氨酯分散液的制备与性能研究

以聚己二酸丁二醇酯二醇(PBA3000)、异佛尔酮二异氰酸酯(IPDI)和2,2-二羟甲基丙酸(DMPA)为主要原料,合成了羧酸型水性聚氨酯(WPU)。结果表明:一步法和两步法制成的WPU分散液及其胶膜特性相近,但一步法制备工艺更加简单;随着DMPA含量不断增加,预聚过程中体系黏度和分散液电导率上升,WPU胶膜的拉伸强度、硬度和吸水率增大,断裂伸长率和分散液粒径(100 nm)减小;当n(PBA)∶n(DMPA)=2∶3时,R值越大,预聚过程中体系黏度越低,WPU胶膜的拉伸强度和硬度越大,而断裂伸长率和吸水率越小;当w(-COOH)=1.09%～2.37%时,WPU分散液的稳定性较好。     

The influence of the degree of neutralization,the ionic moiety,and the counterion on water‐dispersible polyurethanes

A number of polyurethane anionomers based on isophorone diisocyanate, polytetrahydrofuran, and cyclohexane dimethanol were prepared as aqueous dispersions. The dispersions were stabilized by the use of an internal emulsifier. The principal ionic moiety used was dimethylol propanoic acid, but dimethylol butanoic acid and an experimental suphonate diol sodium salt were also used. The consequence of the neutralization step, the degree of neutralization, the type of ionic component, and the type of counterion were investigated for their effect on the mechanical and colloidal properties of the polyurethanes. Dynamic mechanical thermal analysis, tensiometry, solvent spot testing, and swelling studies were used for the characterization of the materials. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 556–566, 1999     

复合薄膜用水性聚氨酯胶粘剂的研究

以聚已二酸1,4-丁二醇酯(PBA)、甲苯二异氰酸酯(TDI)、二羟甲基丙酸(DMPA)等为主要原料合成了水性聚氨酯复膜胶,讨论了亲水性扩链剂DMPA用量对水性聚氨酯复膜胶的稳定性、耐水性、粘接强度等的影响;使用差示扫描量热仪(DSC)和原子力显微镜(AFM)观察了分子结构中的软、硬段微相结构分布。结果表明,当DMPA质量分数占预聚体总质量的2.67%～5.34%时能够制得稳定乳液;水性复膜胶乳液的粘度以及胶膜的吸水率随着亲水性扩链剂DMPA用量的增加而增加,而乳液的粒径随着亲水性扩链剂DMPA用量的增加而减小;硬段含量的增加会降低软段结晶,增加水性聚氨酯复膜胶高分子链的极性和粘接强度,当硬段质量分数为22.79%时,胶膜具有较好的T型剥离强度;提高复合压力能够显著提高T型剥离强度;该复膜胶对聚对苯二甲酸乙二醇酯(PET)膜有着比聚丙烯(OPP)膜更好的粘接效果。