Compatibilization of polymer blends from poly(styrene‐co‐acrylonitrile) and polycarbonate by oxazoline modification of poly(styrene‐co‐acrylonitrile) in the melt

A good way of achieving compatibility in polymer blends of poly(styrene‐co‐acrylonitrile) (S/AN) and bisphenol A polycarbonate (PC) is the chemical modification of S/AN in the melt. A catalyzed reaction of the nitrile groups with a substituted 2‐amino alcohol or 2‐amino phenol resulted in a conversion of nitrile groups of 55–75% in 60 min. The introduced heterocyclic structures were ethyl hydroxymethyl oxazoline (EHMOXA) and benzoxazole (BenzOXA), respectively. The use of dibutyltin oxide as a catalyst led to the highest efficiency. The modified polymer was characterized by Fourier transform infrared and NMR spectroscopy, elemental analysis, and reactions with organic acids and anhydrides. The modified S/AN showed good technical compatibility (single glass‐transition temperature) with PC in blends made from solution and from the melt. All blends were characterized with oscillating rheometry and differential scanning calorimetry. Rheological measurements showed that EHMOXA–S/AN reacted with PC and had crosslinked structures, whereas BenzOXA–S/AN showed compatibilization without any (crosslinking) reaction. The melt blends of BenzOXA–S/AN and PC showed a downward shift in the complex viscosity due to the influence of the BenzOXA group. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2322–2332, 2003     

Blends of bisphenol A polycarbonate and rubber‐toughened styrene–maleic anhydride copolymers

The morphology and mechanical properties of polycarbonate (PC) blends with rubber‐toughened styrene–maleic anhydride copolymer materials (TSMA) were investigated and compared with the properties of blends of PC with acrylonitrile–butadiene–styrene (ABS) materials. The PC/TSMA blends showed similar composition dependence of properties as the comparable PC/ABS blends. Polycarbonate blends with TSMA exhibited higher notched Izod impact toughness than pure PC under sharp‐notched conditions but the improvements are somewhat less than observed for similar blends with ABS. Since PC is known for its impact toughness except under sharp‐notched conditions, this represents a significant advantage of the rubber‐modified blends. PC blends with styrene–maleic anhydride copolymer (SMA) were compared to those with a styrene–acrylonitrile copolymer (SAN). The trends in blend morphology and mechanical properties were found to be qualitatively similar for the two types of copolymers. PC/SMA blends are nearly transparent or slightly pearlescent. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1508–1515, 1999     

Dynamic‐mechanical analysis of MWNTs‐filled PC/ABS blends

In a systematic manner, the roles of MWNTs as filler and styrene acrylonitrile copolymer‐graft‐maleic anhydride (SAN‐MA) as compatibilizer, individually and together, on dynamic‐mechanical behavior of polycarbonate (PC)‐rich/acrylonitrile butadiene styrene terpolymer (ABS) blend were studied. The investigations were performed using small‐scale mixing in a one‐step procedure with a fixed MWNTs content of 0.75 wt% and a blend composition of PC/ABS = 70/30 w/w. PC/SAN blends and nanocomposites as simpler model system for PC/ABS were also studied to reveal the role of the rubbery polybutadiene (PB) fraction. It is found that the tendency of MWNTs to localize within the PC component in compatibilized PC/ABS was lower than in compatibilized PC/SAN blends. Dynamic mechanical analysis (DMA) revealed the dual role of SAN‐MA as blend compatibilizer and also promoter of MWNTs migration towards PC, where SAN‐MA to MWNTs weight ratio varied between 1 and 4. At the compatibilizer/MWNTs weight ratio of 1, MWNTs localized in PC component of the blends whereas increasing the compatibilizer/MWNTs ratio to 4 led to migration of MWNTs toward SAN or ABS component. In DMA studies, loss modulus normalization of the nanocomposites revealed the coexistence of mobilized and immobilized regions within the nanocomposite structure, as a result of MWNTs and compatibilizer loading. POLYM. ENG. SCI., 54:2696–2706, 2014. © 2014 Society of Plastics Engineers     

Influence of acrylonitrile–butadiene–styrene (ABS) morphology and poly(styrene‐co‐acrylonitrile) (SAN) content on fracture behavior of ABS/SAN blends

This study attempted to correlate morphological changes and physical properties for a high rubber content acrylonitrile–butadiene–styrene (ABS) and its diluted blends with a poly(styrene‐co‐acrylonitrile) (SAN) copolymer. The results showed a close relationship between rubber content and fracture toughness for the blends. The change of morphology in ABS/SAN blends explains in part some deviations in fracture behavior observed in ductile–brittle transition temperature shifts. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2606–2611, 2004     

Mechanical,thermal, and morphological properties of recycled polycarbonate/recycled poly(acrylonitrile‐butadiene‐styrene) blend nanocomposites

The present work aims within the context of plastic recycling is to upgrade the properties of plastic waste particularly the two engineering plastics polycarbonate (PC) and poly (acrylonitrile‐butadiene‐styrene) (ABS) from electrical and electronic equipment. Recycled polycarbonate (RPC) and recycled poly (acrylonitrile‐butadiene‐styrene) (RABS) were obtained from E‐waste suppliers. RPC/RABS blends compatibilized with both maleic anhydride‐grafted polypropylene (MAP) and solid epoxy resin was prepared by microinjection molding. The effect of compatibilizer addition on the morphology and mechanical properties of RPC/RABS blends were analyzed. Further, to upgrade the mechanical and thermal properties two types of organically modified nanoclays closite 30B (C30B) and closite 15A (C15A) were incorporated into the optimized blend compositions. The effect of organoclay on the mechanical, thermal, and morphological properties of the RPC/RABS blend nanocomposites was investigated. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Recycling of ABS and ABS/PC blends

The aim of this work within the framework of mechanical recycling of polymers is upgrading recycled engineering plastics by means of a blending technique. Four different plastics from dismantled Volvo cars have been investigated. They are poly(acrylonitrile‐butadiene‐styrene) (ABS) and ABS‐polycarbonate (ABS/PC) as major components and poly(methyl methacrylate) (PMMA) and polyamide (PA) as minor components. Blending recycled ABS and PC/ABS (70/30) with a small amount of methyl methacrylate‐butadiene‐styrene core‐shell impact modifiers gives the mixture better impact properties than any of its individual components. Some 10% of PMMA from tail light housings can follow the PC/ABS blends made. The property profile will rather be improved. However, PA is an incompatible component that should be sorted out from the mixture. Antioxidants and metal deactivators do not help the recyclates show better mechanical properties. Two toughness measurements, Charpy impact strength and J‐integral method, show complimentary results for such blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 510–515, 1999     

The vibration welding of polycarbonate/acrylonitrile‐butadiene‐styrene blends to themselves and to other resins and blends

The weldabilities of two commercial blends of polycarbonate (PC) and acrylonitrile‐butadiene‐styrene (ABS) to themselves and to several other resins and blends are assessed through 120 Hz vibration welds of 6.35‐ and 3.2‐mm‐thick specimens. While the thicker specimens of both blends have relative weld strengths of 83%, the thinner specimens in one of the grades have a lower relative weld strength of 73%. Welds of thicker specimens of both grades to PC have relative strengths of 85%. Again, welds of thinner specimens of one of the grades to PC have a lower relative strengths of 68%. Welds of the thinner specimens of this grade with ABS have relative strengths of 85%. Welds of this material with poly(butylene terephthalate) (PBT), a PC/PBT blend, modified poly(phenylene oxide), and a poly(phenylene oxide)/polyamide blend, have relative weld strengths of 45%, 26%, 76%, and 20%, respectively.     

Effects of tetramethylpolycarbonate‐block‐poly(styrene‐co‐acrylonitrile) copolymers containing various amounts of acrylonitrile on the interfacial properties of polycarbonate and poly(styrene‐co‐acrylonitrile) blends

Tetramethylpolycarbonate‐block‐poly(styrene‐co‐acrylonitrile) (TMPC‐block‐SAN) block copolymers containing various amounts of acrylonitrile (AN) were examined as compatibilizers for blends of polycarbonate (PC) with poly(styrene‐co‐acrylonitrile) (SAN) copolymers. To explore the effects of block copolymers on the compatibility of PC/SAN blends, the average diameter of the dispersed particles in the blend was measured with an image analyzer, and the interfacial properties of the blends were analyzed with an imbedded fibre retraction technique and an asymmetric double‐cantilever beam fracture test. Reduction in the average diameter of dispersed particles and effective improvement in the interfacial properties was observed by adding TMPC‐block‐SAN copolymers as compatibilizer of PC/SAN blend. TMPC‐block‐SAN copolymer was effective as a compatibilizer when the difference in the AN content of SAN copolymer and that of SAN block in TMPC‐block‐SAN copolymer was less than about 10 wt%. Copyright © 2004 Society of Chemical Industry     

Blends of poly(vinyl chloride) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer: Thermal properties,mechanical properties,and morphology

Binary blends of poly(vinyl chloride) (PVC) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer (AMS‐ABS) were prepared via melt blending. A single glass transition temperature (T_g) was observed by differential scanning calorimetry, thus indicating that PVC is miscible with the α‐methylstyrene‐acrylonitrile‐styrene in AMS‐ABS. The results from attenuated total reflection Fourier transform infrared spectra indicated that specific strong interactions were not available in the blends. With increasing amounts of AMS‐ABS, both heat distortion temperature and thermal stability were increased considerably. With regard to mechanical properties, flexural and tensile properties decreased with increasing AMS‐ABS content. A synergism was observed in impact strength. The morphology of both impact‐fractured and tensile‐fractured surfaces, observed by scanning electron microscopy, correlated well with the mechanical properties. It is suggested that there was a transition of fracture mechanisms with the changing composition of the binary blends—from shear yielding for blends rich in PVC to cavitation for blends rich in AMS‐ABS. J. VINYL ADDIT. TECHNOL., 19:1–10, 2013. © 2013 Society of Plastics Engineers     

Influence of the tert‐dodecyl mercaptan content in poly(acrylonitrile‐butadiene‐styrene) on properties of chlorinated polyvinyl chloride/poly(acrylonitrile‐butadiene‐styrene) blends

A series of poly(acrylonitrile‐butadiene‐styrene) (ABS) grafting modifiers were synthesized by emulsion grafting poly(acrylonitrile‐styrene) (SAN) copolymer onto polybutadiene (PB) latex rubber particles. The chain transfer reagent tert‐dodecyl mercaptan (TDDM) was used to regulate the grafting degree of ABS and the molecular weight of SAN copolymers. By blending these ABS modifiers with Chlorinated polyvinyl chloride (CPVC) resin, a series of CPVC/ABS blends were obtained. The morphology, compatibility, and the mechanical properties of CPVC/ABS blends were investigated. The scanning electron microscope (SEM) studies showed that the ABS domain all uniformly dispersed in CPVC matrix. Dynamic mechanical analyses (DMA) results showed that the compatibility between CPVC and SAN became enhanced with the TDDM content. From the mechanical properties study of the CPVC/ABS blends, it was revealed that the impact strength first increases and then decreases with the TDDM content, which means that the compatibility between CPVC and the SAN was not the only requirement for maximizing toughness. The decreasing of tensile strength and the elongations might attribute to the lower entanglement between chains of CPVC and SAN. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Weld‐line characteristics of polycarbonate/acrylonitrile–butadiene–styrene blends. I. Effect of the processing temperature

The effects of the processing temperature on the morphology and mechanical properties at the weld line of 60/40 (w/w) polycarbonate (PC)/acrylonitrile–butadiene–styrene (ABS) copolymer blends were investigated. The influences of the incorporation of poly(methyl methacrylate) (PMMA) as a compatibilizer and an increase in the viscosity of the dispersed ABS domain phase were also studied. The ABS domain was well dispersed in the region below the V notch, and a coarse morphology in the core region was observed. When tensile stress was applied perpendicularly to the weld line, the fracture propagated along the weak region behind the weld part; there, the domain phase coalescence was significant because of the poor compatibility between PC and styrene–acrylonitrile (SAN). Phase coalescence became severe, and so the mechanical strength of the welded specimen decreased with an increasing injection‐molding temperature. The domain morphology became stable and the mechanical strength increased as the viscosity of the domain phase increased or some SAN was replaced with PMMA. That the morphology was well distributed behind the weld line and the mechanical properties of PC/ABS/PMMA blends were improved was attributed to the compatibilizing effect of PMMA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 689–699, 2005     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

Online monitoring of the influence of the chemical structure of hindered amines on the hydrolysis of polycarbonate in a polycarbonate/poly(acrylonitrile–butadiene–styrene) blend by ultraviolet–visible spectroscopy

Without stabilization, polycarbonate (PC)/poly(acrylonitrile–butadiene–styrene) (ABS) blends are susceptible to a loss of mechanical properties after a few days of exposure to weathering conditions. ABS can be stabilized against terrestrial light by the use of hindered amines in combination with a UV absorber; such hindered amines cannot be used when PC is present in the polymer blend. The hydrolysis of PC is accelerated when a small amount of a hindered amine light stabilizer (HALS) is incorporated into the resin and is exposed to elevated temperatures. In this study, three different HALSs (Tinuvin 123, Tinuvin 770, and Tinuvin 765, Ciba, Basel, Switzerland) were used as UV stabilizers for PC/ABS blends, and their effects on the PC phase were observed with online ultraviolet–visible spectroscopy on extruded flat films. These stabilizers were compounded with the blends in a corotating twin‐screw extruder at 240°C. The molecular weight of the compounded samples was determined by gel permeation chromatography. The extent of degradation induced by the HALSs on the PC phase was found to be a function of its chemical structure. Tinuvin 123 with an amino ether functional group enhanced degradation in comparison with Tinuvin 770 and Tinuvin 765. Tinuvin 770, a secondary amine, was apt to be more reactive than Tinuvin 765, a tertiary amine, because less steric hindrance was experienced by the former. Accelerated aging of the compounded samples was performed. Decreased degradation was observed for the samples containing hindered amines; however, the HALSs alone were not effective in protecting the PC/ABS blends against harmful UV light. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Study of a novel halogen‐free flame retardant system through TGA and structure analysis of polymers

Butadiene‐rubber toughened styrene polymers, such as acrylonitrile‐butadiene‐styrene (ABS) copolymer and high impact polystyrene (HIPS), are noncharring polymers. They are generally blended with polycarbonate (PC) or polyphenyleneether (PPE), which are char forming polymers, to improve char forming ability for styrenic blends containing conventional phosphate flame retardants. To achieve cost effective flame retardant system, PET was selected as a potential char‐source for ABS blends through the thermogravimetric analysis (TGA) and chemical structure analysis of various polymers. PET may contribute to the enhancement of flame retardancy of ABS/PET blends, especially in the presence of small amounts of phenol novolac (PN). The effective flame retardancy of this system is believed to be accomplished through the enhancement of interchain reactions by PN. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure–properties relationship in toughening of poly(butylene terephthalate) with core–shell modifier

The performance of acrylonitrile–butadiene–styrene (ABS) core–shell modifier with different grafting degree, acrylonitrile (AN) content, and core–shell ratio in toughening of poly(butylene terephthalate) (PBT) matrix was investigated. Results show PBT/ABS blends fracture in ductile mode when the grafting degree is high, and with the decrease of grafting degree PBT/ABS blends fracture in a brittle way. The surface of rubber particles cannot be covered perfectly for ABS with low grafting degree and agglomeration will take place; on the other hand, the entanglement density between SAN and PBT matrix decreases because of the low grafting degree, inducing poor interfacial adhesion. The compatibility between PBT and ABS results from the strong interaction between PBT and SAN copolymer and the interaction is influenced by AN content. Results show ABS cannot disperse in PBT matrix uniformly when AN content is zero and PBT/ABS fractures in a brittle way. With the addition of AN in ABS, PBT/ABS blends fracture in ductile mode. The core–shell ratio of ABS copolymers has important effect on PBT/ABS blends. When the core–shell ratio is higher than 60/40 or lower than 50/50, agglomeration or cocontinuous structure occurs and PBT/ABS blends display lower impact strength. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 5363–5371, 2006     

Improvement of impact strength and hydrolytic stability of PC/ABS blend using reactive polymer

Polycarbonate/acrylonitrile–butadiene–styrene (PC/ABS) blends have been used widely for specific applications such as in automotive interior and exterior parts, and for office automation equipment parts. This study was conducted to investigate the effects of a reactive polymer as a modifier on properties such as the impact strength of PC/ABS blends. A reaction between PC and maleic anhydride group cannot usually be expected because the end hydroxyl group of PC is capped with an end‐capping agent such as t‐butylphenol to improve PC properties such as fluidity, thermal resistance, and impact strength. However, a reactive polymer that has a maleic anhydride group reacts with the end hydroxyl group of PC hydrolyzed with metal salts. Results show that PC/ABS with a reactive polymer exhibits improved impact strength. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44550.     

Recycling of blends of acrylonitrile–butadiene–styrene (ABS) and polyamide

The aim of this work is to evaluate routes to upgrade recycled engineering plastics, especially mixed plastics with acrylonitrile–butadiene–styrene copolymers (ABS) as the major component. A core‐shell impact modifier was successfully used to improve the impact strength of blends of ABS and ABS/polycarbonate (PC) blends recycled from the automotive industry. However, the presence of other immiscible components like polyamide (PA), even in small amounts, can lead to a deterioration in the overall properties of the blends. A styrene–maleic anhydride (SMA) copolymer and other commercial polymer blends were used to promote the compatibilization of ABS and PA. The core‐shell impact modifier was again found to be an efficient additive with regard to the impact strength of the compatibilized ABS/PA blends. The results obtained with fresh material blends were quite promising. However, in blends of recycled ABS and glass‐fiber‐reinforced PA, the impact strength did not exhibit the desired behavior. The presence of poorly bonded glass fibers in the blend matrix was the probable reason for the poor impact strength compared with that of a blend of recycled ABS and mineral‐filled PA. Although functionalized triblock rubbers (SEBS–MA) can substantially enhance the impact strength of PA, they did not improve the impact strength of ABS/PA blends because the miscibility with ABS is poor. The possibilities of using commercial polymer blends to compatibilize otherwise incompatible polymer mixtures were also explored giving promising results. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2535–2543, 2002     

Melt processing,mechanical, and fatigue crack propagation properties of reactively compatibilized blends of polyamide 6 and acrylonitrile–butadiene–styrene copolymer

Within a IUPAC study, melt processing, mechanical, and fatigue crack growth properties of blends of polyamide 6 (PA 6) and poly(acrylonitrile–butadiene–styrene) (ABS) were investigated. We focused on the influence of reactive compatibilization on blend properties using a styrene–acrylonitrile–maleic anhydride random terpolymer (SANMA). Two series of PA 6/ABS blends with 30 wt % PA 6 and 70 wt % PA 6, respectively, were prepared with varying amounts of SANMA. Our experiments revealed that the morphology of the matrix (PA 6 or ABS) strongly affects the blend properties. The viscosity of PA 6/ABS blends monotonically increases with SANMA concentration because of the formation of high‐molecular weight graft copolymers. The extrudate swell of the blends was much larger than that of neat PA 6 and ABS and decreased with increasing SANMA concentrations at a constant extrusion pressure. This observation can be explained by the effect of the capillary number. The fracture resistance of these blends, including specific work to break and impact strength, is lower than that of PA 6 or ABS alone, but increases with SANMA concentration. This effect is most strongly pronounced for blends with 70 wt % PA 6. Fatigue crack growth experiments showed that the addition of 1–2 wt % SANMA enhances the resistance against crack propagation for ABS‐based blends. The correlation between blend composition, morphology and processing/end‐use properties of reactively compatibilized PA 6/ABS blends is discussed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical performance of ternary in situ polycarbonate/poly(acrylonitrile‐butadiene‐styrene)/liquid crystalline polymer composites

Ternary in situ polycarbonate (PC)/poly(acrylonitrile‐butadiene‐styrene) (ABS)/liquid crystalline polymer(LCP) composites were prepared by injection molding. The LCP used was a versatile Vectra A950, and the matrix of composite specimens was PC/ABS 60/40 by weight. Maleic anhydride (MA) copolymer and solid epoxy resin (bisphenol type‐A) were used as compatibilizers for these composites. The tensile, dynamic mechanical, impact, morphology, and thermal properties of the composites were studied. Tensile tests showed that the tensile strength of the PC/ABS/LCP composite in the longitudinal direction increased markedly with increasing LCP content. However, it decreased slowly with increasing LCP content in the transverse direction. The modulus of this composite in the longitudinal direction appeared to increase considerably with increasing LCP content, whereas the incorporation of LCP into PC/ABS blends had little effect on the modulus in the transverse direction. The impact tests revealed that the Izod impact strength of the composites in both longitudinal and transverse direction decreased with increasing LCP content up to 15 wt %; thereafter it increased slowly with increasing LCP. Dynamic mechanical analyses (DMA) and thermogravimetric measurements showed that the heat resistance and heat stability of the composites tended to increase with increasing LCP content. Scanning electron microscopy observation and DMA measurement indicated that the additions of epoxy and MA copolymer to PC/ABS matrix appeared to enhance the compatibility between the PC and ABS, and between the matrix and LCP. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2274–2282, 1999     

Melt‐mixed polypropylene/acrylonitrile‐butadiene‐styrene blends with multiwall carbon nanotubes: Effect of compatibilizer and modifier on morphology and electrical conductivity

Cocontinuous blends of 45/55 polypropylene (PP)/acrylonitrile‐butadiene‐styrene (ABS) with multiwall carbon nanotubes (MWNT) were prepared by melt‐mixing in a conical twin‐screw microcompounder. PP‐grafted‐maleic anhydride (PP‐g‐MA) and styrene MA were used as compatibilizers for PP/ABS blends. Scanning electron microscopic observations showed phase segregation of PP‐g‐MA in the blends. State of dispersion of MWNT in the presence or absence of the compatibilizers was assessed through AC electrical conductivity measurements and crystallization studies of the blends. An improvement in AC electrical conductivity was observed in blends in presence of either styrene MA or dual compatibilizers. The lowest electrical percolation threshold was achieved at 0.1 wt % of MWNT using sodium salt of 6‐amino hexanoic acid‐modified MWNT. Significant increase in crystallization temperature of PP phase of blends with MWNT was observed in the presence of compatibilizers as compared to blends without compatibilizers. An attempt has been made to address the complex issues of phase segregation, compatibilization, and dispersion of MWNT in cocontinuous blends of PP/ABS. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011