Crosslinking reaction of glycidyl methacrylate copolymers containing oxime-urethane groups using photogenerated pendant amines

Summary Copolymers containing epoxy and oxime-urethane groups were prepared by copolymerization of glycidyl methacrylate (GMA) and benzophenone oxime allylurethane (BAU). The physical properties of these copolymers were characterized by GPC, NMR and DSC analyses. Photo-crosslinking reaction of the copolymers were studied by measuring the insoluble fraction of copolymer films under various reaction conditions. The degree of cross-linking reaction increased with irradiation time, heating temperature and the amount of BAU units in the copolymer. UV and IR absorption spectral studies indicate that thermal cross-linking reaction of the copolymer was catalyzed by the pendant photogenerated amines. Received: 3 March 1998/Revised version: 7 April 1998/Accepted: 15 April 1998     

Photo-crosslinking of polymeric photobase generator bearing O-acyloxime moieties with low eliminating by-products and high sensitivity

O-Acyloximes are a class of photobase generators (PBGs) that release a primary amine upon irradiation. The generated amine can be used as a crosslinker for polymers bearing epoxy groups, providing a novel photo-induced crosslinking system. However, O-acyloximes also release a ketone by-product that migrates and exudes from the crosslinked polymer. To reduce the migration and elimination of the ketone, 4-vinylacetophenone O-phenylacetyloxime (PaVO) was proposed as a monomeric PBG, and its copolymer with glycidyl methacrylate (PaVO-co-GMA) was compared to poly(glycidyl methacrylate) (PGMA) containing acetophenone O-phenylacetyloxime (PaApO) as a molecular PBG (PaApO/PGMA). Film thickness, infrared (IR), and ultraviolet (UV) spectral changes upon irradiation clarified the vaporization of photoproducts from the PaApO/PGMA films, while such behavior was not observed for the PaVO-co-GMA films. Furthermore, when PaVO-co-GMA was blended with PGMA, less irradiation energy was required for its crosslinking when compared to that of PaApO/PGMA, which contained the same molar ratio of the O-acyloxime unit.     

Surface modification of polyethylene by plasma pretreatment and UV‐induced graft polymerization for improvement of antithrombogenicity

The purpose of this study was to enhance blood compatibility of polyethylene (PE) films. Glycidyl methacrylate (GMA) was grafted onto the surface of PE by Ar plasma pretreatment and UV‐induced graft polymerization without photo‐initiator, then heparin was immobilized onto the poly (glycidyl methacrylate) segments. The surface compositions and microstructure of GMA graft polymerized PE films were studied by X‐ray photoelectron spectroscopy (XPS) and Attenuated Total Reflectance Fourier Transfer Infrared (ATR‐FTIR) spectroscopy. It was confirmed that heparin was successfully immobilized onto the surface of PE films by XPS analysis. The antithrombogenicity of the samples was determined by the activated partial thromboplastin time (APTT), prothrombin time (PT), thrombin time (TT), and plasma recalcification time (PRT) tests and platelet adhesion experiment. Results indicated that the antithrombogenicity of modified PE was improved remarkably. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2014–2018, 2004     

Detection of residual acidic groups in several poly(N‐alkyl methacrylate)s using photophysical and photochemical probes

This work describes three different methods for detecting acidic groups copolymerized in poly(methyl methacrylate), poly(ethyl methacrylate), and poly(n‐butyl methacrylate) chains using molecular spectroscopy. The first was based on the shift of the tautomeric equilibrium of 4‐dimethylaminoazobenzene by acidic groups that modify the absorption band in the UV/vis spectra. We also show that the acidic groups present in the polymer influenced the anti‐syn photoisomerization reaction of this dye. Further, a mercury–dithizonate complex was completely bleached when sorbed in poly(n‐alkyl methacrylate) matrices containing acidic groups. Finally, Nile Blue A was used as a spectrophotometric probe to quantify the amount of acidic groups in these polymers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 830–838, 2004     

Biologically active polymers. IV. Synthesis and antimicrobial activity of polymers containing 8‐hydroxyquinoline moiety

Polymers containing 8‐hydroxyquinoline moiety were prepared. Modifications of the base polymer of glycidyl methacrylate were carried out in order to introduce chloromethyl groups, either by the hydrolysis of the poly(glycidyl methacrylate) and the chloroacetylation of the hydrolyzed polymer by the reaction with chloroacetyl chloride or by aminating the poly(glycidyl methacrylate) either with ethylenediamine or with hexamethylenediamine, followed by reacting the aminated polymers with chloroacetyl chloride. The polymers containing 8‐hydroxyquinoline moiety were prepared by reacting the chloromethyl groups containing polymers with potassium salt of 8‐hydroxy quinoline. The antimicrobial activity of the polymers obtained was examined against gram‐negative bacteria (Escherichia coli) and gram‐positive bacteria (Bacillus subtilus) as well as the fungus Trichophyton rubrum. Generally, all three polymers proved effective against the tested microorganisms, but growth inhibitory effects varied from one another. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1364–1374, 2001     

Surface modification of polythiophene and poly(3‐methyl thiophene) films by graft copolymerization

Polythiophene (PTH) and poly(3‐methyl thiophene) (PMT) films were electrochemically polymerized in an electrolyte solution of boron fluoride–ethyl ether. Ozone‐pretreated PTH and PMT films were subjected to UV‐light‐induced graft copolymerization with different monomers, including poly(ethylene glycol) monomethacrylate, acrylic acid, and glycidyl methacrylate. Surface grafting with the hydrophilic polymers gave rise to more hydrophilic PTH and PMT films. The structure and chemical composition of each copolymer surface were studied by X‐ray photoelectron spectroscopy. The surface grafting with the hydrophilic polymers resulted in a more hydrophilic PTH film. The dependence of the density of surface grafting and the conductivities of the grafted PTH and PMT films on the ozone pretreatment was also studied. A large amount of the grafted groups at the surface of the PTH and PMT films remained free for further surface modification and functionalization. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Radiational hardening of poly(vinylidene fluoride)–poly(methyl methacrylate)–polystyrene ternary blends

Specimens of poly(vinylidene fluoride) (PVDF)–poly(methyl methacrylate) (PMMA)–polystyrene (PS) polyblends with different weight percentage ratios of the three polymers were prepared with the solution cast technique. The effect of γ irradiation on the Vicker's microhardness was studied. Among the three pure polymers, PVDF, PMMA, and PS, the γ irradiation imparted crosslinking in PVDF, thereby causing radiational hardening. In the cases of PMMA and PS, the effect of irradiation exhibited a predominance of both the scissioning and crosslinking processes in different ranges of doses. Moreover, at a dose of 5 Mrad, in both PMMA and PS, maximum radiational crosslinking was observed. The effect of γ irradiation seemed to stabilize beyond 15 Mrad in PVDF and beyond 20 Mrad in PMMA and PS. Microhardness measurements on ternary blends of PVDF, PMMA, and PS revealed that the blend with low contents of PMMA, that is, up to 5 wt %, yielded softening, whereas increasing the content of PMMA beyond 5 wt % produced a hardened material because of radiational crosslinking, and a higher content of PMMA in the blend facilitated this crosslinking. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3107–3111, 2004     

Synthesis and photopolymerization of acrylic acrylate copolymers

Acrylate‐functionalized copolymers were synthesized by the modification of poly(butyl acrylate‐co‐glycidyl methacrylate) (BA/GMA) and poly(butyl acrylate‐co‐methyl methacrylate‐co‐glycidyl methacrylate). ¹³C‐NMR analyses showed that no glycidyl methacrylate block longer than three monomer units was formed in the BA/GMA copolymer if the glycidyl methacrylate concentration was kept below 20 mol %. We chemically modified the copolymers by reacting the epoxy group with acrylic acid to yield polymers with various glass‐transition temperatures and functionalities. We studied the crosslinking reactions of these copolymers by differential scanning calorimetry to point out the effect of chain functionality on double‐bond reactivity. Films formed from acrylic acrylate copolymer precursors were finally cured under ultraviolet radiation. Network heterogeneities such as pendant chains and highly crosslinked microgel‐like regions greatly influenced the network structure and, therefore, its viscoelastic properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 753–763, 2002     

Photo-crosslinkable polymers with benzylideneacetophenone (chalkone) structure in the side chains

Four soluble types of polymers have been synthesized by grafting 4- and 4′-chalkonyl glycidyl ethers onto an aromatic polyamine (aniline–formaldehyde linear resin) and a polyamide (condensation product of dimerized linseed oil and an aliphatic polyamine) to obtain photo-crosslinkable chalkone structure in the side chains which are also expected to contain one ? OH group each. The completion of grafting reactions has been followed by the disappearance of the epoxide absorption around 918 cm^?1. The characterization of the resins was done by melting point, solubility, and IR measurements. Irradiation was carried out with a 100-watt Hanovia high-pressure mercury are lamp. Irradiated samples were studied by UV spectral measurements and their insolubility in CHCl₃. It was observed that polymers grafted with 4′-chalkonyl glycidyl ether possibly undergo both isomerization and crosslinking reactions under UV irradiation while those grafted with 4-chalkonyl glycidyl ether undergo crosslinking reaction predominantly.     

Synthesis of CdS nanoparticles dispersed within amphiphilic poly(urethane acrylate‐co‐styrene) films

CdS nanoparticles were prepared using amphiphilic urethane acrylate nonionomer (UAN) precursor chains having a poly(propylene oxide)‐based hydrophobic segment and a hydrophilic poly(ethylene oxide) segment. Cadmium salts were first dissolved in UAN/styrene solutions, and then the solutions were copolymerized to obtain poly(urethane acrylate‐co‐styrene) films containing dissolved cadmium salts. After reduction with H₂S gas, freestanding films containing CdS nanoparticles were obtained. Transmission electron microscopy images of the films showed that 9.67‐nm CdS nanoparticles were dispersed within the poly(urethane acrylate‐co‐styrene) matrix. The formation of CdS nanoparticles was also confirmed with UV absorption spectra and photoluminescence emission spectra of the films. Transmission electron microscopy and dynamic mechanical analysis measurements confirmed that hydrophilic/hydrophobic microphase separation in UAN/styrene solutions occurred during the dissociation of the cadmium salts, and the microphase‐separated structures were locked in by crosslinking copolymerization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2357–2363, 2005     

Lamination of high‐density polyethylene by bulk photografting and the mechanism of adhesion

The photolamination of high‐density polyethylene (HDPE) by bulk photografting is described, along with a discussion of the adhesion mechanism. HDPE can be photolaminated very easily with a thin poly(acrylic acid) layer, photopolymerized from acrylic acid, with very strong adhesion obtained after a short time of UV irradiation; the adhesion failure mode is polyethylene breakage. Thicker HDPE sheets require longer irradiation times for strong adhesion. Methacrylic acid or hydroxyethyl methacrylate provides no adhesion of HDPE at all after irradiation. When glycidyl acrylate is used alone between HDPE sheets, the peel strength of the photolaminated polyethylene is only approximately 320 N/m, but when glycidyl acrylate or hydroxyethyl methacrylate is grafted with acrylic acid, very good adhesion can be obtained. It is proposed that stronger adhesion is produced by a less branched grafted chain structure, which permits much more chain entanglement. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1097–1106, 2005     

Preparation and characterization of novel crosslinked poly[glycidyl methacrylate–poly(ethylene glycol) methyl ether methacrylate] as gel polymer electrolytes

In this study, glycidyl methacrylate was copolymerized with poly(ethylene glycol) methyl ether methacrylate to obtain a copolymer {poly[glycidyl methacrylate–poly(ethylene glycol) methyl ether methacrylate] [P(GMA–PEGMA)]}, which was crosslinked with α,ω‐diamino poly(propylene oxide) (Jeffamine) at various weight ratios and molecular weights to form novel gel polymer electrolytes (GPEs). The crosslinked copolymers were characterized by Fourier transform infrared spectroscopy and thermal analysis. The crosslinked polymers were amorphous in the pristine state and became crystallized after they were doped with lithium electrolyte. Furthermore, the crosslinking degree of the crosslinked polymers increased with increasing weight ratio of Jeffamine, and both the swelling properties and mechanical behaviors of the crosslinked polymers were heavily affected by the weight ratio and molecular weight of Jeffamine. The ionic conductivity (σ) of the GPEs from the crosslinked copolymers was determined by alternating‐current impedance spectroscopy. A higher molecular weight and increased weight ratio of Jeffamine resulted in a higher σ. The GPE based on P(GMA–PEGMA) crosslinked with an equal weight of Jeffamine D2000 exhibited the highest σ of 8.29 × 10⁻⁴ S/cm at 25°C and had a moderate mechanical strength. These crosslinked copolymers could be potential candidates for the construction of rechargeable lithium batteries. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis,characterization, and mechanical property of poly(urethane‐glycidyl methacrylate‐methyl methacrylate) hybrid polymers

Hybrid particles of polyurethane (PU) containing a number of small poly(methyl methacrylate) (PMMA) nanoparticles inside were prepared using glycidyl methacrylate (GMA) monomer as a linker between PU and PMMA; the resulting polymers were poly (urethane‐glycidyl methacrylate‐methyl methacrylate) (PUGM). It was found that the average particle size (D_p) of the PU particles decreased by the inclusion of PMMA particles possibly owing to the low‐solution viscosity of PU. However, D_p of the PUGM hybrid particles increased with increasing the number of covalent bonds between PMMA and PU, which might be due to decreasing the amount of ionic groups per PU chain. Subsequently, the tensile properties of the films made of the PUGM hybrid particles were investigated. It was observed that the modulus of the PU films increased upon the addition of PMMA particle because of a filler effect. In addition, it was seen that the modulus of PUGM hybrid films increased further with increasing the number of covalent bonds. This was attributed to “restricted mobility” of PU chains anchored to the PMMA particles. It was also observed that the tensile strength changed only slightly for PUGM particles, suggesting that the PU matrix was probably responsible for the necking behavior of the films. The elongation of the samples was found to depend on both the presence of covalent bonds between the PMMA particles and PU matrix and the reduced mobility of the PU chains anchored to PMMA particles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

New polyurethane cationomers with naphthyl and phenyltriazene pendants: Synthesis and properties

Two new diols bearing triazene moiety, 1‐(α‐naphthyl)‐3,3‐di(2‐hydroxyethyl) triazene‐1 (NT‐D) and 1‐phenyl‐3,3‐di(2‐hydroxyethyl) triazene‐1 (PT‐D), were synthesized from aromatic amines and diethanolamine. These monomers were used as chain coextenders in the two‐step addition reaction between poly(tetramethylene oxide) diol, 2,4‐tolylene diisocyanate, and N‐methyldiethanolamine to obtain photosensitive polyurethanes of elastomer type. Triazene polyurethane cationomers with chlorine counterions were prepared via a quaternization reaction of the above polymers with benzyl chloride. All polyurethanes had a quantity of triazene units between 7.02 and 8.93 wt % polymer, and the content of ammonium quaternary groups in the cationic ones was of 30.56 meq/100 g naphthyl triazene polyurethane cationomer (PUC‐NT) and 30.19 meq/100 g phenyl triazene polyurethane cationomer (PUC‐PT), respectively. Photobehavior of the triazene units in all polymers under continuous Hg‐lamp irradiation was similar to that found for monomers, when both chromophores were transformed during UV irradiation. It is concluded that the PT‐D acts as a more efficient sensitizer in the UV light‐induced reaction but the photolysis in elastomeric films was lower than that observed in solution. The presence of quaternary ammonium structure on the same polymer backbone decreases the constant rates of photolysis. Because the triazene polyurethanes become crosslinked during UV irradiation could be assessed as potential negative‐resist polymers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2599–2605, 2004     

Preparation and characterization of UV‐curable ZnO/polymer nanocomposite films

A series of novel nano‐ZnO/polymer composite films with different ZnO contents was prepared through incorporation of pre‐made colloidal ZnO particles into monomer mixtures of urethane‐methacrylate oligomer and 2‐hydroxyethyl methacrylate, followed by ultraviolet (UV) radiation‐initiated polymerization. The colloidal ZnO nanoparticles with a diameter of 3–5 nm were synthesized from zinc acetate and lithium hydroxide in ethanol via a wet chemical method. In order to stabilize and immobilize the ZnO particles into the polymer matrix, the ZnO nanoparticles were further capped using 3‐(trimethoxysilyl)propyl methacrylate. Thermogravimetric analyses show that the ZnO nanoparticles were successfully incorporated into the polymer matrix and these ZnO/polymer composites have a good thermal stability. Transmission electron microscopy studies indicate the ZnO nanoparticles were uniformly dispersed in the polymer and they remained at the original size (3–5 nm) before immobilization. All nanocomposite films with ZnO particle contents from 1 to 15 wt% show good transparency in the visible region and luminescent properties. In addition, composite films with high ZnO content (>7 wt%) are able to absorb UV irradiation below 350 nm, indicating that these composite films exhibit good UV screening effects. Copyright © 2006 Society of Chemical Industry     

Synthesis and characteristics of photoactive‐hydrogenated rosin epoxy methacrylate for pressure sensitive adhesives

Hydrogenated rosin epoxy methacrylate (HREM), based on hydrogenated rosin and glycidyl methacrylate (GMA), was synthesized for use as an advanced tackifier in the UV‐crosslinking pressure sensitive adhesives (PSAs) system. The HREM, as a tackifier, contained UV‐curing sites; thus, allowed photopolymerization to occur by UV irradiation. This UV‐curable tackifier, HREM, can improve the curing rate and adhesion performance of UV‐crosslinking PSAs. The characteristics of HREM were analyzed by GPC and DSC and its synthetic mechanism studied using FTIR and ¹H NMR; the characteristic peaks of hydrogenated rosin and GMA vanished, but new peaks for HREM appeared. The PDI and the T_g by DSC were 1 and ?25.6°C, respectively. The photopolymerization of HREM was studied using photo‐DSC. Heat flow was observed during UV irradiation, and the curing rate and conversion both increased with rising photoinitiator content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of poly(glycidyl methacrylate) grafted sulfonamide based polystyrene resin with tertiary amine for the removal of dye from water

Poly(glycidyl methacrylate) was grafted onto crosslinked poly(styrene) beads through the 2-chloroethyl sulphonamide (CSA) groups present in the resin using ATRP polymerization method. A beaded polymer with a poly(glycidyl methacrylate) surface shell was prepared in three steps, starting from poly(styrene-DVB) (10% crosslinking) based beads with a particle size of 420–590 μm, according to the synthetic protocol; chlorosulfonation, sulfamidation with 2-chloroethylamine hydrochloride and grafting reaction of poly(glycidyl methacrylate).The polymeric resin was prepared with 147.8% of grafted glycidyl methacrylate and subsequent modified with diethyl amine to introduce tertiary amine groups. This resin has also been demonstrated to be an efficient dye sorbent, able to remove dye from water even at ppm levels. The dye sorption capacity under non-buffered conditions is around 0.90 g dye/g resin.     

Effects of crosslinking by quinones on dyeing of irradiated films of copolymers bearing photobase generating groups

Films of copolymers of methyl methacrylate and O-acryloyl acetophenone oxime (AAPO), which is a monomer bearing photobase generating groups, were UV-irradiated and dyed in the presence of p-benzoquinone or 1,4-naphthoquinone. Acyloxyimino groups in AAPO units were transformed into pendant amino groups on irradiation, and films became well dyeable with an acid dye. The quinones in the films caused crosslinking, which reduced the damage of the films during the dyeing processes compared to those without quinones. Sublimed p-benzoquinone was also introduced into heated films after irradiation, which resulted in the success of lowering the surface roughness of the films during the dyeing processes. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1177–1184, 1998     

Synthesis and characterization of novel copolymers with acid‐labile ketal moieties derived from camphor

Novel diastereomeric acrylic ketal monomers derived from (+)‐camphor and (±)‐camphor were synthesized. To investigate the applications of the camphor derivatives on positive‐tone photoresists, the acrylic ketal monomers were copolymerized with methyl methacrylate, methacrylic acid, and n‐butyl methacrylate. The optical activities of the chiral monomers and polymers were all evaluated. After UV irradiation and postexposure baking, the optical activity of the polymers decreased because of the decomposition of the acid‐labile pendant chiral groups. The existence of alicyclic camphyl groups increased the etching resistance of the photoresists. The thermogravimetric properties of the copolymers, the exposure curves, the lithographic evaluation of the positive‐tone photoresists, and the effects of alicyclic groups on the plasma etching resistance of the copolymers were all investigated. A resolution of a line‐and‐space pattern of 0.3 μm was achieved. Acid‐catalyzed dehydration crosslinking was also found in this system. Sufficient UV irradiation and heat treatment could cause the acid‐catalyzed dehydration crosslinking of pendant carboxyl groups and thereby increase the efficiency of the thermal resistance of the polymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2969–2978, 2003     

Preparation and characterization of binary blends composed of poly(dioctylfluorene‐alt‐hexylsulfonylthiophene) and nonconjugated polymers

The solutions and the thin films of poly[9,9‐dioctyl‐2,7‐fluorene‐alt‐2,5–(3‐hexyl‐sulfonylthiophene)] (PFSO₂T) and its binary blends with other nonconjugated polymers such as poly(methyl methacrylate) (PMMA), polycarbonate (PC), and ethylene vinyl acetate copolymer (EVA) can be prepared by different concentrations from a polymer solution. Binary polymer blends can increase the absorbance and photoluminescence intensities in the solid state due to nonconjugated polymers can act as dispersion agents which can reduce the interchain interaction or the aggregation of the conjugated polymers. Photoluminescence intensity of the thin films of fluorescent polymers blending with ethylene vinyl acetate copolymers exhibited six times higher than that of the neat fluorescent polymers. The PFSO₂T/EVA binary blends reveal the least extent of optical degradation of around 20% compared to those binary blends in both absorption and emission intensities after the irradiation under the UV‐light for 20 h. The cross‐sectional morphology of fluorescent polymers blending with ethylene vinyl acetate copolymers reveals little aggregation and better phase separation among the other binary polymer blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44969.