Interface and mechanical properties of poly(methyl methacrylate)–fiber composites

Long‐fiber pellets were made by an in situ pultrusion process. Fiber‐reinforced composites were prepared by an injection‐molding process and an extrusion/injection‐molding method with pellets, respectively. SEM observations showed that the strong interface was maintained during the injection process for low shearing forces, although polymer adhesion to the fiber surface was completely delaminated in the process of extrusion/injection molding for very high shearing forces. Enhanced adhesion of composites promoted substantial improvement of mechanical properties compared to those with poor adhesion. However, the enhanced adhesion between the fiber and the matrix also sacrificed the impact resistance properties. Longer fibers substantially enhanced the properties of composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2478–2483, 2004     

Investigation on crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends by solution casting

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by solution casting. The crystallization behavior and hydrophilicity of ternary blends were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and contact angle test. According to morphological analysis, the surface was full of typical spherulitic structure of PVDF and the average diameter was in the order of 3 μm. The samples presented predominantly β phase of PVDF by solution casting. It indicated that the size of surface spherulites and crystalline phase had little change with the PMMA or PVP addition. Moreover, FTIR demonstrated special interactions among the ternary polymers, which led to the shift of the carbonyl stretching absorption band of PVP. On the other hand, the melting, crystallization temperature, and crystallinity of the blends had a little change compared with the neat PVDF in the first heating process. Except for the content of PVP containing 30 wt %, the crystallinity of PVDF decreased remarkably from 64% to 33% and the value of t_1/2 was not obtained. Besides, the hydrophilicity of PVDF was remarkably improved by blending with PMMA/PVP, especially when the content of PVP reached 30 wt %, the water contact angle displayed the lowest value which decreased from 98.8° to 51.0°. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of gold nanoparticles on poly(methyl methacrylate) nanospheres with surface-grafted poly(allylamine)

A facile method for in situ anchoring of gold nanoparticles onto the surface of polymer nanospheres was successfully developed in this study. As polymer nanospheres, amphiphilic poly(methyl methacrylate) (PMMA)/poly(allylamine) (PAA) nanospheres were prepared by graft copolymerization of methyl methacrylate from PAA. The gold nanoparticles anchored were spherically symmetric and the average sizes were ∼12 nm for all samples. It was found that surface-grafted PAA effectively anchored and stabilized gold nanoparticles for a long period of time.     

悬浮聚合法制取不同分子量级别的聚甲基丙烯酸甲酯

采用粉状MgCO3 作为分散剂 ,悬浮聚合制取了分子量从 2 4× 10 4 ～ 2 5 4× 10 4 的聚甲基丙烯酸甲酯。考察了温度、引发剂种类和浓度、分子量调节剂、转化率对聚合物分子量的影响规律 ,用粘度法测量了聚合物聚甲基丙烯酸甲酯 (PMMA)的分子量。结果表明 :温度的升高、引发剂浓度的增大、分子量调节剂的加入都会导致分子量的减小 ,随着转化率的提高 ,聚合物的分子量增大。在同等条件下 ,引发剂过氧化苯甲酰 (BPO)聚合所得的分子量较偶氮二异丁腈 (AIBN)高。通过实验 ,得到了满足作者需求的分子量 (96× 10 4 ～ 10 0× 10 4 )的聚合物的聚合条件为 :分散剂MgCO3 用量 1% ,单体∶水相 =1∶2 5 (质量比 ) ,引发剂BPO浓度 0 5 % ,反应温度 70℃ ,反应时间 3h。     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Preparation of compatible blends of poly(methyl methacrylate) used in dentistry with a reactive terpolymer containing maleic anhydride and their thermomechanical characterization

This study focuses on the preparation of compatible blends with the poly(methyl methacrylate) (PMMA) using a reactive terpolymer maleic anhydride–styrene–vinyl acetate (MA–St–VA). In the first series of experiments, binary blends of the PMMA and the MA–St–VA terpolymer have been prepared in tetrahydrofurane. The PMMA and the MA–St–VA terpolymer formed the compatible blends. The effects on thermomechanical properties of MA–St–VA terpolymer ratio in the blends were studied. The glass transition temperatures (T_g), thermal expansion coefficient (α), and other thermomechanical parameters for the blends have been established by TMA method and the compatibility of two polymers has been evaluated by these TMA parameters. The addition of MA–St–VA terpolymer to PMMA made a plasticizing effect on PMMA. This effect regularly changed with the increasing of the terpolymer in the blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 363–367, 2006     

Fabrication and morphology control of poly(methyl methacrylate) hollow structures via coaxial electrospinning

A modified electrospinning method known as coaxial electrospinning was used to fabricate poly(methyl methacrylate) (PMMA) hollow structures. In this study to understand morphology control, the effect of processing parameters such as concentration of polymer sheath solution, size of core/sheath capillaries, feed rate, and applied voltage had been evaluated. Morphological observations via scanning electron microscope (SEM) revealed that via the control of polymer concentration within the sheath solution, morphologies such as hollow particles and fibers could be obtained. With the use of fine core/sheath capillaries, micron hollow fibers with walls of less than 20 nm were obtained. This study has demonstrated how the investigated processing parameters have a direct influence on the structures and how these parameters have supported the notion that effective encapsulation process is the key to the dual layer bicomponent structures. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子的制备

由种子乳液聚合法制备了聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子。以过硫酸钾(KPS)为引发剂,辛基酚聚氧乙烯醚(OP-10)为乳化剂,合成了聚苯乙烯(PS)种子核;连续滴加甲基丙烯酸甲酯(MMA),在核表面富集MMA,制备了粒径范围在0.16~0.67μm的核-壳粒子;当单体苯乙烯与甲基丙烯酸甲酯(St/MMA)的比为30∶70(质量比)时,所得粒径在0.18μm,粒径分布为0.012。差示扫描量热(DSC)研究显示,复合粒子的玻璃化转变温度(Tg)为97.2℃,峰形单一,表现出良好的热性能。     

Optical properties of particle‐filled polycarbonate,polystyrene, and poly(methyl methacrylate) composites

Transparency is a key material property of polycarbonate (PC), polystyrene (PS), and poly(methyl methacrylate) (PMMA). To study the optical properties of particle‐filled PC, PS, and PMMA, composites containing inorganic particles in different sizes and concentrations were produced by direct melt mixing in this work. The optical properties characterized by total light transmittance, haze, and clarity were studied. The results show that the optical properties of polymer composites are strongly affected by particle content, particle size, and especially by difference in refractive indices between polymer matrix and particles. It is also revealed that the light transmittance and haze of composites are mainly affected by difference in refractive indices, whereas the clarity is more affected by particle size. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Electrospinning of cyclodextrin functionalized poly(methyl methacrylate) (PMMA) nanofibers

Cyclodextrin functionalized PMMA nanofibers (PMMA/CD) were successfully produced by electrospinning technique with the goal to develop functional nanowebs. Bead-free uniform electrospun PMMA/CD nanofibers were obtained from a homogeneous solution of CDs and PMMA in dimethylformamide (DMF) using three different types of CDs, α-CD, β-CD and γ-CD. The electrospinning conditions were optimized in order to form bead-free PMMA/CD nanofibers by varying the concentrations of PMMA and CDs in the solutions. The concentration of CDs was varied from 5% up to 50% w/w, with respect to the PMMA matrix. We find that the presence of the CDs in the PMMA solutions facilitates the electrospinning of bead-free nanofibers from the lower polymer concentrations and this behavior is attributed to the high conductivity and viscosity of the PMMA/CD solutions. The X-ray diffraction (XRD) spectra of PMMA/CD nanowebs did not show any significant diffraction peaks indicating that the CD molecules are homogeneously distributed within the PMMA matrix and does not form any phase separated crystalline aggregates. Furthermore, attenuated total reflection Fourier transform infrared (ATR-FTIR) studies elucidate that some CD molecules are located on the surface of the nanowebs. This suggests that these CD functionalized nanowebs may have the potential to be used as molecular filters and/or nanofilters for waste treatment purposes.     

Comparison of the phase behaviour of the liquid-crystalline polymer/poly(methyl methacrylate) and poly(vinyl acetate)/poly(methyl methacrylate) blends

The phase behaviour of blends of a liquid-crystalline polymer (LCP) and poly(methyl methacrylate) (PMMA), as well as the phase state of blends of PMMA and poly(vinyl acetate) (PVA) has been investigated using light scattering and phase-contrast optical microscopy. The blends of LCP and PMMA have been obtained by coagulation from ternary solutions. The cloud point curves were determined. It was established that both pairs demix upon heating, ie have an LCST. In the region of intermediate composition, the phase separation proceeds according to a spinodal mechanism; however for LCP/PMMA blends, the decomposition proceeds according to a non-linear regime from the very onset. In the region of small amounts of LCP, the phase separation follows a mechanism of nucleation and growth. For PMMA/PVA blends, the spinodal decomposition proceeds according to a linear regime, in spite of the molecular mobility that PVA chains develop at lower temperatures. Only after prolonged heat treatment does the process transit to a non-linear regime. The data show a similarity between the phase behaviour of blends of liquid-crystalline and of flexible amorphous polymers. The distinction consists of the absence of a linear regime of decomposition for LCP-PMMA blends. © 1999 Society of Chemical Industry     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl pyrrolidone)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMA) (designated iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(vinyl pyrrolidone) (PVP) primarily in chloroform to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PVP. The aPMMA/PVP and sPMMA/PVP blends were found to be miscible because all the prepared films showed composition-dependent glass-transition temperatures (T_g). The glass-transition temperatures of the aPMMA/PVP blends are equal to or lower than weight average and can be qualitatively described by the Gordon–Taylor equation. The glass-transition temperatures of the other miscible blends (i.e., sPMMA/PVP blends) are mostly higher than weight average and can be approximately fitted by the simplified Kwei equation. The iPMMA/PVP blends were found to be immiscible or partially miscible based on the observation of two glass-transition temperatures. The immiscibility is probably attributable to a stronger interaction among isotactic MMA segments because its ordination and molecular packing contribute to form a rigid domain. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3190–3197, 2001     

Synthesis and properties of poly(methyl methacrylate)/montmorillonite (PMMA/MMT) nanocomposites

PMMA/MMT nanocomposites were successfully synthesized via in situ intercalative polymerization, and characterized by means of wide‐angle X‐ray diffractometry, transmission electron microscopy, thermal gravimetric analysis, dynamic mechanical analysis and Fourier‐transform infrared analysis. The nanocomposites possess partially exfoliated and partially intercalated structure, in which the silicate layers are exfoliated into nanometre secondary particles with thickness of less than 20 nm and uniformly dispersed in the polymer matrix. In comparison with pure PMMA, the thermal stability, glass transition temperature, and mechanical properties of the polymer are notably improved by the presence of the nanometric silicate layers. It was found that part of the PMMA chains in the nanocomposites are well immobilized inside and/or onto the layered silicates and, therefore, the unique properties of the nanocomposites result from the strong interactions between the nanometric silicate layers and the polymer chains. Copyright © 2003 Society of Chemical Industry     

Preparation and characterizations of interpenetrating polymer network hydrogels of poly(ethylene oxide) and poly(methyl methacrylate)

Interpenetrating polymer network (IPN) hydrogels based on poly(ethylene oxide) and poly(methyl methacrylate) were prepared by radical polymerization using 2,2‐dimethyl‐2‐phenylacetophenone and ethylene glycol dimethacrylate as initiators and crosslinkers, respectively. The IPN hydrogels were analyzed for sorption behavior at 25°C and at a relative humidity of 95% using dynamic vapor sorption. The IPN hydrogels exhibited a relatively high equilibrium water content in the range of 13–68%. The state of water in the swollen IPN hydrogels was investigated using differential scanning calorimetry. The free water in the hydrogels increased as the hydrophilic content increased. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 258–262, 2003     

Preparation and characterization of poly(methyl methacrylate) beads

The phase behavior of Poly(ethylene terephthalate)/Poly(ethylene‐2,6‐naphthalate)/Poly(ethylene terephthalate‐co‐ethylene‐2,6‐naphthalate) (PET/PEN/P(ET‐co‐EN)) ternary blends in molten state was evaluated from differential scanning calorimetry (DSC) and NMR results as well as optical microscopic observations. Copolymer of ethylene terephthalate and ethylene‐2,6‐naphthalate was prepared by a condensation polymerization, which was a random copolymer with an intrinsic viscosity (IV) of 0.3 dL/g. The phase diagram of the ternary blends revealed that the miscibility of ternary blends in molten state was dependent on the fraction of P(ET‐co‐EN) in the blends and holding time of the blends at high temperatures above 280°C. With increase in the holding time, the fraction of copolymer in the blends necessary to induce the immiscible to miscible transition decreased. For the blends with longer holding time at 280°C, the phase diagram in molten state was irreversible against the temperature, although a reversibility was found for the blends with short holding time of 1 min at 280°C. The irreversibility of phase behavior was not explained simply by the increase of copolymer content produced during heat treatment. Complex irreversible physical and chemical interactions between components and change of phase structure of the blend in the molten state might influence on the irreversibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl acetate)

The results of the miscibility between the chemically similar polymers poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) published so far show inconsistent statements concerning miscibility. The problems may be due to differences in molecular weights, tacticity, and preparation methods of the polymers. This investigation was carried out by using either chloroform or tetrahydrofuran (THF) as solvent to prepare the blends, because to our knowledge, nobody has reported any tacticity effect of PMMA on the miscibility with PVAc. Therefore, in this article, different tactic PMMAs were used to mix with PVAc and their miscibility was studied calorimetrically. The results showed little effect of solvent and tacticity. PMMA and PVAc were determined to be almost completely immiscible because of the observation of two T_g's. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 35–39, 2004     

Properties of mineral filled poly(lactic acid)/poly(methyl methacrylate) blend

This study examines the influence of three different minerals, that is, clay, calcium carbonate, and quartz on the physical, thermal, and mechanical properties of poly(lactic acid) (PLA)/poly(methyl methacrylate) blend. Rheological behavior and phase structure were initially studied by small-amplitude oscillatory shear rheology. Clay- and quartz-filled materials presented an increase in viscosity at low frequency associated with the presence of a yield stress. However, this behavior was not observed for calcium carbonate filled materials due to a matrix degradation effect. To elucidate this aspect, thermal stability and thermal properties were examined by thermogravimetric analysis and differential scanning calorimetry, showing that calcium carbonate promotes degradation of the PLA phase. No nucleating effect was observed in the presence of the minerals. Dynamical mechanical analysis and mechanical characterization revealed an increase of the overall softening temperature and, a reinforcing effect for clay- and quartz-based composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46927.     

Preparation of graded materials for miscible polycarbonate/poly(methyl methacrylate) blends by segregation under shear flow

Exposure to shear flow produced by a pressure-driven capillary rheometer provides a concentration gradient without phase separation in miscible polymer blends of bisphenol-A polycarbonate containing low-molecular-weight poly(methyl methacrylate) (PMMA). The strand surface extruded from the rheometer contains a large amount of PMMA. However, the strand is transparent because there is no light scattering due to phase separation. The segregation behavior, that is, enrichment of the PMMA content at the strand surface, is enhanced when the molecular weight of PMMA is low. Furthermore, the segregation is also enhanced at high temperatures and at high shear rates. By contrast, the die length barely affects the degree of segregation. The segregation phenomenon should be noted because it may facilitate the modification of the surface properties of various products.     

Effect of Silica‐Coated Poly(butyl methacrylate)‐block‐poly(methyl methacrylate) Double‐Shell Particles on the Mechanical Properties of PMMA Composites

Silica nanoparticles with an average diameter of 12 nm are grafted with PBMA‐b‐PMMA double shells through typical sequential ATRP from bromoisobutyrate initiators anchored at the silica surface using an epoxysilane. A commercially available PMMA homopolymer is used for the preparation of composites with unmodified, silane‐modified and double‐shell‐modified silica particles. Good mechanical properties are obtained for silica double shell containing systems. The silica content in double shell particle systems is varied from 0 to 2.5 wt%. A significant improvement in impact properties is observed. The surface‐modified silica particles are characterized by ATR‐FTIR, NMR, GPC, and thermal analyses. TEM analysis is used to analyze the nature of dispersion of particles in the composites.