High-Temperature Exposure Studies of HVOF-Sprayed Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-25(NiCr)/(WC-Co) Coating

In this research, development of Cr₃C₂-25(NiCr) + 25%(WC-Co) composite coating was done and investigated. Cr₃C₂-25(NiCr) + 25%(WC-Co) composite powder [designated as HP2 powder] was prepared by mechanical mixing of [75Cr₃C₂-25(NiCr)] and [88WC-12Co] powders in the ratio of 75:25 by weight. The blended powders were used as feedstock to deposit composite coating on ASTM SA213-T22 substrate using High Velocity Oxy-Fuel (HVOF) spray process. High-temperature oxidation/corrosion behavior of the bare and coated boiler steels was investigated at 700 °C for 50 cycles in air, as well as, in Na₂SO₄-82%Fe₂(SO₄)₃ molten salt environment in the laboratory. Erosion-corrosion behavior was investigated in the actual boiler environment at 700 ± 10 °C under cyclic conditions for 1500 h. The weight-change technique was used to establish the kinetics of oxidation/corrosion/erosion-corrosion. X-ray diffraction, field emission-scanning electron microscopy/energy-dispersive spectroscopy (FE-SEM/EDS), and EDS elemental mapping techniques were used to analyze the exposed samples. The uncoated boiler steel suffered from a catastrophic degradation in the form of intense spalling of the scale in all the environments. The oxidation/corrosion/erosion-corrosion resistance of the HVOF-sprayed HP2 coating was found to be better in comparison with standalone Cr₃C₂-25(NiCr) coating. A simultaneous formation of protective phases might have contributed the best properties to the coating.     

Mechanical and Tribological Properties of HVOF-Sprayed (Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-NiCr+Ni) Composite Coating on Ductile Cast Iron

The aim of the investigations was to compare the microstructure, mechanical, and wear properties of Cr₃C₂-NiCr+Ni and Cr₃C₂-NiCr coatings deposited by HVOF technique (the high-velocity oxygen fuel spray process) on ductile cast iron. The effect of nickel particles added to the chromium carbide coating on mechanical and wear behavior in the system of Cr ₃ C ₂ -NiCr+Ni/ductile cast iron was analyzed in order to improve the lifetime of coated materials. The structure with particular emphasis of characteristic of the interface in the system of composite coating (Cr ₃ C ₂ -NiCr+Ni)/ductile cast iron was studied using the optical, scanning, and transmission electron microscopes, as well as the analysis of chemical and phase composition in microareas. Experimental results show that HVOF-sprayed Cr₃C₂-NiCr+Ni composite coating exhibits low porosity, high hardness, dense structure with large, partially molten Ni particles and very fine Cr₃C₂ and Cr₇C₃ particles embedded in NiCr alloy matrix, coming to the size of nanocrystalline. The results were discussed in reference to examination of bending strength considering cracking and delamination in the system of composite coating (Cr ₃ C ₂ -NiCr+Ni)/ductile cast iron as well as hardness and wear resistance of the coating. The composite structure of the coating provides the relatively good plasticity of the coating, which in turn has a positive effect on the adhesion of coating to the substrate and cohesion of the composite coating (Cr₃C₂-NiCr+Ni) in wear conditions.     

Microstructure and Thermal Properties of Atmospheric Plasma-Sprayed Yb<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>7</Subscript> Coating

In the present work, Yb₂Si₂O₇ powder was synthesized by solid-state reaction using Yb₂O₃ and SiO₂ powders as starting materials. Atmospheric plasma spray technique was applied to fabricate Yb₂Si₂O₇ coating. The phase composition and microstructure of the coating were characterized. The density, open porosity and Vickers hardness of the coating were investigated. Its thermal stability was evaluated by thermogravimetry and differential thermal analysis (TG-DTA). The thermal diffusivity and thermal conductivity of the coating were measured. The results showed that the as-sprayed coating was mainly composed of crystalline Yb₂Si₂O₇ with amorphous phase. The coating had a dense structure containing defects, such as pores, interfaces and microcracks. The TG-DTA results showed that there was almost no mass change from room temperature to 1200 °C, while a sharp exothermic peak appeared at around 1038 °C in DTA curve, which indicated that the amorphous phase crystallized. The thermal conductivity of the coating decreased with rise in temperature up to 600 °C and then followed by an increase at higher temperatures. The minimum value of the thermal conductivity of the Yb₂Si₂O₇ coating was about 0.68 W/(m K).     

High-Temperature Erosive Behavior of Plasma Sprayed Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-NiCr/Cenosphere Coating

This research examines the deposition of Cr₃C₂-NiCr/cenosphere and Cr₃C₂-NiCr coatings on MDN 321 steel through the process of plasma spray. In this process, the solid particle erosion test is established at 200, 400, 600 °C with 30° and 90° impact angles. Alumina erodent is adopted to investigate the erosive behavior of the coating at higher temperatures. The properties of the Cr₃C₂-NiCr/cenosphere coating are established based on the microhardness, the adhesive strength, the fracture toughness, and the ductility. To quantify volume loss as a result of erosion, an optical profilometer is used. At higher temperature, decrease in the erosion volume loss of Cr₃C₂-NiCr/cenosphere and Cr₃C₂-NiCr coatings is observed. The erosion-resistive property of Cr₃C₂-NiCr/cenosphere coating is higher than that of MDN 321 steel by 76%. This property is influenced by high-temperature stability of mullite, alumina, and protective oxide layer that is formed at elevated temperatures. The morphology of eroded coating discloses a brittle mode of material removal.     

Thermal Spray Deposition,Phase Stability and Mechanical Properties of La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>/LaAlO<Subscript>3</Subscript> Coatings

This paper deals with the deposition of La₂Zr₂O₇ (LZO) and LaAlO₃ (LAO) mixtures by air plasma spray (APS). The raw material for thermal spray, single phase LZO and LAO in a 70:30 mol.% ratio mixture was prepared from commercial metallic oxides by high-energy ball milling (HEBM) and high-temperature solid-state reaction. The HEBM synthesis route, followed by a spray-drying process, successfully produced spherical agglomerates with adequate size distribution and powder-flow properties for feeding an APS system. The as-sprayed coating consisted mainly of a crystalline LZO matrix and partially crystalline LAO, which resulted from the high cooling rate experienced by the molten particles as they impact the substrate. The coatings were annealed at 1100 °C to promote recrystallization of the LAO phase. The reduced elastic modulus and hardness, measured by nanoindentation, increased from 124.1 to 174.7 GPa and from 11.3 to 14.4 GPa, respectively, after the annealing treatment. These values are higher than those reported for YSZ coatings; however, the fracture toughness (K _IC) of the annealed coating was only 1.04 MPa m^0.5.     

Development and Application of Binary Suspensions in the Ternary System Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for S-HVOF Spraying

Compositions in the system Cr₂O₃-TiO₂-Al₂O₃ are among the most used ceramic materials for thermally sprayed coating solutions. Cr₂O₃ coatings present good sliding wear resistance; Al₂O₃ coatings show excellent insulation behavior and TiO₂ striking corrosion properties. In order to combine these properties, coatings containing more than one oxide are highly interesting. The conventional spraying process is limited to the availability of binary feedstock powders with defined compositions. The use of suspensions offers the opportunity for tailor-made chemical compositions: within the triangle of Cr₂O₃-TiO₂-Al₂O₃, each mixture of oxides can be created. Criteria for the selection of raw materials as well as the relevant aspects for the development of binary suspensions in the Cr₂O₃-TiO₂-Al₂O₃ system to be used as feedstock for thermal spraying are presented. This formulation of binary suspensions required the development of water-based single-oxide suspensions with suitable behavior; otherwise, the interaction between the particles while mixing could lead up to a formation of agglomerates, which affect both the stability of the spray process and the coating properties. For the validation of this formulation procedure, binary Cr₂O₃-TiO₂ and Al₂O₃-TiO₂ suspensions were developed and sprayed using the S-HVOF process. The binary coatings were characterized and discussed in terms of microstructure and microhardness.     

Effect of the addition of Sm<Subscript>2</Subscript>O<Subscript>3</Subscript> on the microstructure of laser cladding alloy coating layers

The effects on the microstructures and phases of coating layers by the addition of micron-sized (m) and nano-sized (n) (m&n) Sm₂O₃ powders were investigated. The coating materials, which were prepared by means of 2.0 kW CO₂ laser cladding, consist of a powder mixture of m Ni-based alloy (NBA) powders comprising 1.5 wt.% m Sm₂O₃ and 3.0% n Sm₂O₃ powders. The results indicate that γ-Ni, Cr₂₃C₆ and Ni₃B are the primary phases of the NBA coatings. The Fe₇Sm and Ni₃Si phases are highlighted by the addition of m&n Sm₂O₃ powders. From the substrate, planar crystal layers are first grown in all NBA and m&n Sm₂O₃/NBA coatings. The dendrite growth then occurs as a result of the addition of the m Sm₂O₃ powder, and the equiaxed dendrite growth occurs as a result of the addition of the n Sm₂O₃. With the addition of a rare earth oxide such as Sm₂O₃ powder, the width of the planar crystal becomes smaller than that of the NBA coating.     

Dual-Layer Oxidation-Protective Plasma-Sprayed SiC-ZrB<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Carbon Nanotube Coating on Graphite

Graphite is used in high-temperature gas-cooled reactors because of its outstanding irradiation performance and corrosion resistance. To restrict its high-temperature (>873 K) oxidation, atmospheric-plasma-sprayed SiC-ZrB₂-Al₂O₃-carbon nanotube (CNT) dual-layer coating was deposited on graphite substrate in this work. The effect of each layer was isolated by processing each component of the coating via spark plasma sintering followed by isothermal kinetic studies. Based on isothermal analysis and the presence of high residual thermal stress in the oxide scale, degradation appeared to be more severe in composites reinforced with CNTs. To avoid the complexity of analysis of composites, the high-temperature activation energy for oxidation was calculated for the single-phase materials only, yielding values of 11.8, 20.5, 43.5, and 4.5 kJ/mol for graphite, SiC, ZrB₂, and CNT, respectively, with increased thermal stability for ZrB₂ and SiC. These results were then used to evaluate the oxidation rate for the composites analytically. This study has broad implications for wider use of dual-layer (SiC-ZrB₂/Al₂O₃) coatings for protecting graphite crucibles even at temperatures above 1073 K.     

Growth Kinetics and Microstructure Evolution of Intermediate Phases in MoSi<Subscript>2</Subscript>-Si<Subscript>3</Subscript>N<Subscript>4</Subscript>-WSi<Subscript>2</Subscript>/Mo Diffusion Couples

The growth kinetics and silicon diffusion coefficients of intermediate silicide phases in MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂/Mo diffusion couple prepared by spark plasma sintering were investigated in temperatures ranging from 1200 to 1500 °C. The intermediate silicide phases were characterized by x-ray diffraction. The microstructures and components of the MoSi₂-Si₃N₄-WSi₂/Mo composites were investigated using scanning electron microscope with energy-dispersive spectroscopy. A special microstructure with MoSi₂ core surrounded by a thin layer of (Mo,W)Si₂ ring was found in the MoSi₂-Si₃N₄-WSi₂ composites. The intermediate layers of Mo₅Si₃ and (Mo,W)₅Si₃ in the MoSi₂-Si₃N₄-WSi₂/Mo diffusion couples were formed at different diffusion stages, which grew parabolically. Activation energy of the growth of intermediate layers in MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂/Mo diffusion couple was calculated to be 316 ± 23 kJ/mol. Besides, the hindering effect of WSi₂ addition on the growth of intermediate layers was illustrated by comparing the silicon diffusion coefficients in MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂/Mo and MoSi₂-3.5 vol.% Si₃N₄/Mo diffusion couples. MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂ coating on Mo substrate exhibited a better high-temperature oxidation resistance in air than that of MoSi₂-3.5 vol.% Si₃N₄ coating.     

Dependence of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> coating thickness and annealing conditions on microstructural and electrochemical properties of LiCoO<Subscript>2</Subscript> film

We studied the dependence of Al₂O₃ coating thickness and annealing conditions on the surface morphology and electrochemical properties of Al₂O₃ coated LiCoO₂ films. The optimum coating thickness allowing for the highest capacity retention was about 24 nm. A sample consisting of Al₂O₃ coated on annealed LiCoO₂ film with additional annealing at 400 °C had a uniform coating layer between the coating materials and cathode films. This sample showed the best capacity retention of ∼91 % with a charge-cut off of 4.5 V after 30 cycles, while the bare cathode film showed a capacity retention of ∼32 % under the same conditions. The formation of second phases such as Co-Al-O was observed in the coating films by X-ray photoelectron spectroscopy (XPS). The Co-Al-O containing samples showed a higher initial capacity because of their smaller grain size, but less capacity retention than the Al₂O₃ containing samples.     

Mechanical synthesis and rapid consolidation of nanocrystalline 3Fe<Subscript>0.67</Subscript>Cr<Subscript>0.33</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite by high frequency induction heating

Nanopowders of 3Fe_0.67Cr_0.33 and Al₂O₃ were synthesized from CrO₃ and 2FeAl powders by high-energy ball milling. A highly dense nanocrystalline 3Fe_0.67Cr_0.33-Al₂O₃ composite was consolidated by a high frequency induction heated sintering (HFIHS) method within three minutes from mechanically synthesized powders of Al₂O₃ and 3Fe_0.67Cr_0.33. The average grain size and mechanical properties of the composite were investigated.     

Type II Hot Corrosion Screening Tests of a Cr<Subscript>2</Subscript>AlC MAX Phase Compound

Low-temperature hot corrosion tests were performed on bulk Cr₂AlC MAX phase compounds for the first time. This material is a known alumina-former with good oxidation and Type I high-temperature hot corrosion resistance. Unlike traditional (Ni,Co)CrAl alumina formers, it contains no Ni or Co that may react with Na₂SO₄ salt deposits needed to form corrosive mixed (Ni,Co)SO₄–Na₂SO₄ eutectic salts active in Type II hot corrosion. Cr₂AlC samples coated with 20K₂SO₄–80Na₂SO₄ salt were exposed to 300 ppm SO₂ at 700 °C for times up to 500 h. Weight change, recession, and cross-sectional microstructures identified some reactivity, but much reduced (<?1/10) compared to a Ni(Co) superalloy baseline material. Layered Al₂O₃/Cr₂O₃ scales were indicated, either separated by or intermixed with some retained salt. However, there was no conclusive indication of salt melting. Accelerated oxidation was proposed to explain the results, and coarse Cr₇C₃ impurities appeared to play a negative role. In contrast, the superalloy exhibited outer Ni(Co) oxide and inner Cr₂O₃ scales, with Cr–S layers at the interfaces. Massive spallation of the corrosion layers occurred repeatedly for the superalloy, but not at all for Cr₂AlC. This indicates some potential for Cr₂AlC as LTHC-resistant coatings for superalloys.     

Tribocorrosion Behavior of Fe-Based Amorphous Composite Coating Reinforced by Al<Subscript>2</Subscript>O<Subscript>3</Subscript> in 3.5% NaCl Solution

Although corrosion and friction/wear behavior of Fe-based amorphous coatings and their composites has been extensively studied during the past decade, there is very limited work related to tribocorrosion behavior. In this paper, the tribocorrosion behavior of a Fe-based amorphous composite coating reinforced with 20 wt.% Al₂O₃ particles was investigated in a 3.5% NaCl solution on a ball-on-disk tester and was compared to the monolithic amorphous coating and 316L stainless steel (SS). The results showed that the amorphous composite coating exhibited the highest tribocorrosion resistance among the three materials tested, as evidenced by the lowest coefficient of friction (~0.3) and tribocorrosion wear rate (~1.2 × 10^?5 mm³/N·m). In addition, potentiodynamic polarization measurements before and during tribocorrosion testing demonstrated that corrosion resistance of the amorphous composite coating was not influenced so much by mechanical loading compared to the amorphous coating and the 316L SS. Observations on the worn surface revealed a corrosion-wear- and oxidational-wear-dominated tribocorrosion mechanism for the composite coatings. The excellent tribocorrosion resistance of the composite coating results from the effect of chemically stable Al₂O₃ phase which resists oxidation and delamination during sliding, along with poor wettability with corrosive NaCl droplets.     

Oxidation Behavior of NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> Spinel-Coated Interconnects in Wet Air

Corrosion of boilers and heat exchangers is accelerated in the presence of vanadium, sodium, and sulfur from low-grade fuels. Several iron- and nickel-based alloys were immersed in 60 mol% V₂O₅–40Na₂SO₄ salt for 1000 h in order to investigate their degradation behavior at 600 °C in air. Materials performance was analyzed by means of substrate recession rate and metallographic characterization. Their corrosion mechanism is characterized by the formation of a sulfide/oxide layer adjacent to the metal, the dissolution of scale oxides in the molten deposit, and their precipitation near the outer surface of the deposit. High Ni- and Cr-containing alloys show the lowest metal loss rates. Al addition was detrimental due to low-melting eutectic AlVO₄–V₂O₅ formation. Fe–Cr-based alloys showed the highest metal loss rates. In such alloys, high Cr additions (above 20%) did not improve the performance due to the negative synergetic effect by simultaneous dissolution of Fe₂O₃ and Cr₂O₃. The predominant salt composition at the corrosion front varied from vanadate rich to sulfate rich during the exposure. This change in the attacking salt makes it difficult to find a protective material for mixed sulfate–vanadate-induced corrosion.     

Corrosion Behavior and Microhardness of Ni-P-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nano-composite Coatings on Magnesium Alloy

In the present work, nano-composites of Ni-P-SiO₂-Al₂O₃ were coated on AZ91HP magnesium alloy. The surface morphology of the nano-composite coating was studied by field emission scanning electron microscopy (FESEM). The amount of SiO₂ in the coating was determined by energy-dispersive analysis of x-ray (EDX), and the crystalline structure of the coating was examined by x-ray diffractometer (XRD). All the experiments concerning the corrosion behavior of the coating carried out in 3.5 wt.% NaCl solution and evaluated by electrochemical impedance spectroscopy (EIS) and polarization technique. The results showed that an incorporation of SiO₂ and Al₂O₃ in Ni-P coating at the SiO₂ concentration of 10 g/Land 14 g/LAl₂O₃ led to the lowest corrosion rate (i _corr = 1.3 µA/cm²), the most positive E _corr and maximum microhardness (496 VH). Furthermore, Ni-P-SiO₂-Al₂O₃ nano-composite coating possesses less porosity than that in Ni-P coating, resulting in improving corrosion resistance.     

Effect of Nano-Si<Subscript>3</Subscript>N<Subscript>4</Subscript> Additives and Plasma Treatment on the Dry Sliding Wear Behavior of Plasma Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-8YSZ Ceramic Coatings

In this paper, the effect of nano-Si₃N₄ additives and plasma treatment on the wear behavior of Al₂O₃-8YSZ ceramic coatings was studied. Nano-Al₂O₃, nano-8YSZ (8 wt.% Y₂O₃-stabilized ZrO₂) and nano-Si₃N₄ powders were used as raw materials to fabricate four types of sprayable feedstocks. Plasma treatment was used to improve the properties of the feedstocks. The surface morphologies of the ceramic coatings were observed. The mechanical properties of the ceramic coatings were measured. The dry sliding wear behavior of the Al₂O₃-8YSZ coatings with and without Si₃N₄ additives was studied. Nano-Si₃N₄ additives and plasma treatment can improve the morphologies of the coatings by prohibiting the initiation of micro-cracks and reducing the unmelted particles. The hardness and bonding strength of AZSP (Al₂O₃-18 wt.% 8YSZ-10 wt.% Si₃N₄-plasma treatment) coating increased by 79.2 and 44% compared to those of AZ (Al₂O₃-20 wt.% 8YSZ) coating. The porosity of AZSP coating decreased by 85.4% compared to that of AZ coating. The wear test results showed that the addition of nano-Si₃N₄ and plasma treatment could improve the wear resistance of Al₂O₃-8YSZ coatings.     

Corrosion of Inconel 690 in N<Subscript>2</Subscript>-0.1%H<Subscript>2</Subscript>S gas at 700-800 °C

Inconel 690 superalloy was corroded at 700 °C and 800 °C for up to 70 h in N₂-0.1% H₂S gas. It corroded almost linearly with large weight gains, displaying little protectiveness. Its corrosion rates were quite fast when compared with its corrosion in air or Ar-1%SO₂ gas. The formed scales were thick, fragile, and nonadherent. They consisted primarily of Cr₂O₃ with some NiCr₂O₄, Ni₃S₂, CrS, and Cr₂S₃. The H₂S gas accelerated the corrosion significantly by forming nonprotective sulfides and dissolving hydrogen in the scale and in the internal corrosion zone that consisted of discrete chromium-sulfides and some oxide particles. The marker test indicated that the scales grew by the outward diffusion of metallic ions such as Ni, Cr, Fe, and Mn, whilst the internal corrosion zone thickened by the inward migration of oxygen and sulfur through the lattice, grain boundaries, and microcracks.     

Microstructure and Thermomechanical Properties of Atmospheric Plasma-Sprayed Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> Coating

In this study, a Yb₂O₃ coating was fabricated by the atmospheric plasma spray technique. The phase composition, microstructure, and thermal stability of the coating were examined. The thermal conductivity and thermal expansion behavior were also investigated. Some of the mechanical properties (elastic modulus, hardness, fracture toughness, and flexural strength) were characterized. The results reveal that the Yb₂O₃ coating is predominantly composed of the cubic Yb₂O₃ phase, and it has a dense lamellar microstructure containing defects. No mass change and exothermic phenomena are observed in the thermogravimetry and differential thermal analysis curves. The high-temperature x-ray diffraction results indicate that no phase transformation occurs from room temperature to 1500 °C, revealing the good phase stability of the Yb₂O₃ coating. The coefficient of thermal expansion of the Yb₂O₃ coating is (7.50-8.67)?×?10^?6 K^?1 in the range of 200-1400 °C. The thermal conductivity is about 1.5 W m^?1 K^?1 at 1200 °C. The Yb₂O₃ coating has excellent mechanical properties and good damage tolerant. The unique combination of these properties implies that the Yb₂O₃ coating might be a promising candidate for T/EBCs applications.     

The Improvement of Oxidation Resistance of a Re-Based Diffusion Barrier/Ni�CAl Coating on the Single-Crystal Ni-Based TMS-82+ Superalloy

Oxidation behavior of a Re-based diffusion barrier/Ni?CAl coated single-crystal (SC) Ni-based TMS-82+ superalloy was studied to compare with those of the base and Ni?CAl coated superalloys under cyclic air at 1150 °C for 200 h. The base superalloy showed a negative mass gain due to extensive oxide spallation, and the Ni?CAl coated superalloy without the diffusion barrier started to spall slightly after about 90 h. The oxidation resistance of the Ni?CAl coated superalloy with the Re-based diffusion barrier was greatly improved due to the formation of a dense ??-Al₂O₃ layer in the scale. The Re-based alloy was an effective diffusion barrier layer against inward diffusion of Al and outward diffusion of alloying elements in the alloy substrate due to the reduced thickness of interdiffusion zone with small amount of detrimental precipitates and higher content of Al in the Ni?CAl coating that supplied enough Al for formation of the ??-Al₂O₃ layer.     

Comparative analysis of the kinetics of dissolution of oxides Y<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> in the iron matrix upon mechanical alloying

The kinetics of low-temperature dissolution of oxides Y₂O₃ and Fe₂O₃ in an iron matrix during mechanical alloying has been studied using electron microscopy. It has been shown that the dissolution rate upon deformation of primary coarse oxides Fe₂O₃ in α iron (and, hence, saturation of the α matrix with oxygen) during treatment in a ball mill for up to 10 h is several times higher than the dissolution rate of Y₂O₃ oxides. The high-temperature (1100°C) annealing of a mechanoalloyed mixture of Fe + 1.5% Y + 1.35% Fe₂O₃ leads to the precipitation of 60% (of the total number of particles) secondary oxides 2–5 nm in size and only of 5–7% secondary nanooxides in a mechanoalloyed mixture of Fe + 2% Y₂O₃.