共查询到19条相似文献,搜索用时 171 毫秒
1.
《高压电器》2017,(11):152-158
变压器绝缘纸中水分会加速油纸绝缘的老化,缩短变压器寿命,因此,准确诊断变压器绝缘纸老化状态以及水分含量对变压器安全运行具有重要意义。文中通过测试分析不同水分、不同聚合度的绝缘油纸回复电压曲线,研究发现当绝缘纸处于低水分含量状态(0.5%≤Mp<3%)时,回复电压参数随水分含量改变变化较快,当绝缘纸处于高水分含量状态(3%≤Mp≤5%)时,回复电压4个参数值基本保持稳定。回复电压最大值、初始斜率随绝缘纸水分含量呈负指数规律增长,而中心时间常数和回复电压半衰期呈负指数规律减小,4个参数随水分改变的变化幅度均随绝缘纸聚合度线性变化,通过数据拟合得到回复电压特征参量与绝缘纸聚合度、水分含量的表达式。回复电压半衰期与绝缘纸水分含量及老化状态关系密切,能作为反映固体绝缘纸微水含量和聚合度的有效特征参量。 相似文献
2.
3.
针对电力变压器油纸绝缘系统由于自身老化产气、换油处理不当等引入气隙(空穴)的影响绝缘性能研究方法的不足,引入回复电压法有效诊断油纸绝缘状态来判断气隙状况。在理解介质响应理论基础上,建立了油纸绝缘模拟实验,统计分析并拟合了测量数据,研究了不同充电时间下绝缘系统中气隙含量的变化对回复电压特征参数的影响规律。结果表明:回复电压最大值随绝缘系统中气隙含量的增加呈二次线性规律增大,而中心时间常数随绝缘系统中气隙含量的增加呈二次线性规律减小,初始斜率随着绝缘系统中气隙含量增加呈三次线性规律增大,最后对多台实际变压器进行测试分析,验证了回复电压法可对油纸绝缘系统中气泡情况有效诊断的结论。 相似文献
4.
5.
6.
基于扩展德拜模型,建立油纸绝缘变压器绝缘状态与介质响应等值电路之间的关系,并仿真分析模型(时间常数、支路数)改变引起回复电压特征参数和极化谱的变化规律。仿真分析结果表明,极化谱回复电压峰值与主时间常数可作为变压器绝缘诊断的判据,且时间常数不同的RC支路在回复电压极化谱的对应区段才有所影响。通过研究多台不同绝缘状态的变压器,总结出绝缘老化程度与支路数取值的内在联系,由此获取的等值参数最优,所建立模型与变压器实际状况相吻合,可作为油纸绝缘系统状态准确诊断和研究的基础。 相似文献
7.
目前,国内外学者对回复电压法做了大量的研究,但是还没有一个明确评估变压器油纸绝缘老化状态的方法。在理解介质极化特性的前提下,以变压器油纸绝缘极化等效电路模型为基础,仿真分析了回复电压特征量随极化等效电路参数(极化电阻、极化电容以及支路数)变化的规律。仿真结果表明,回复电压峰值的最大值、回复电压初始斜率最大值及主时间常数等可用来评估变压器绝缘状况。同时,等效电路模型的支路数也可辅助评估变压器的绝缘状况。最后对多台实际变压器进行测试分析,验证了上述特征量用于评估变压器绝缘状态是可行的。 相似文献
8.
9.
基于介质响应理论的回复电压测量方法能够有效地无损诊断变压器的绝缘状态。应用回复电压测量仪RVM5461在2 000 V极化电压,0.5~1 000 s一系列充电时间,充放电时间比为2的实验条件下对1台110 kV容量31.5 MVA的变压器进行回复电压测试。利用测试得到的初试斜率、回复电压最大值、主时间常数3个特征量应用改进粒子群算法计算得到变压器油纸绝缘扩展德拜模型等效电路,并通过仿真分析了各极化支路参数的改变对回复电压极化谱的变化规律。分析结果表明,小时间常数支路、中时间常数支路和大时间常数支路分别主要影响回复电压极化谱初始、中端、末端部分。 相似文献
10.
针对油纸绝缘变压器内部绝缘介质弛豫响应的复杂性,根据油纸绝缘结构特征,提出建立混联等效电路新模型来表征油纸绝缘弛豫过程。根据混联等效电路的理论分析,推导出混联等效电路参数和回复电压的求解公式。先采用一台变压器回复电压测试数据对该方法进行验证后,再利用一台变压器检修前后的测试数据进行基于混联等效电路的变压器油纸绝缘诊断研究。研究结果表明:通过混联等效电路方法得到的回复电压曲线能够很好的与现场测量的回复电压曲线吻合,且利用混联等效电路能够准确的诊断油纸绝缘变压器的绝缘介质老化情况。 相似文献
11.
基于EMD和相关向量机的短期负荷预测 总被引:3,自引:1,他引:3
为提高电力负荷预测的准确性,提出一种基于经验模态分解EMD(empirical mode decomposition)与相关向量机RVM(relevant vector machine)的短期负荷预测方法。该方法利用EMD将目标负荷序列分解为若干个不同频率的固有模态分量I MF(intrinsic mode function),通过分析各个分量的特征规律,构造不同的RVM模型对各分量分别进行预测,再将各分量预测值通过RVM组合得到最终预测值。仿真结果表明,通过EMD分解,预测效果有显著改善,而RVM模型较之BP神经网络模型与SVM模型具有更高的预测精度。 相似文献
12.
13.
为可靠地进行万能式断路器机械故障诊断,在基于振动信号故障诊断的基础上,提出了一种多特征融合与改进量子粒子群(QPSO)优化的相关向量机(RVM)相结合的万能式断路器分合闸故障振声诊断方法。首先,对振声信号进行小波包软硬阈值结合去噪预处理,并利用互补总体经验模态分解算法对处理后的振声信号进行分解,提取固有模态函数能量系数、样本熵、功率谱熵,并组成多特征参数;然后,通过组合核函数核主元分析对多特征参数降维,并将其特征融合组成特征向量作为RVM的输入,解决单一特征识别断路器分合闸故障的低准确率和低稳定性;最后,利用改进QPSO优化分类模型参数,建立基于RVM的次序二叉树模型对断路器故障进行辨识。实验结果表明,该方法能有效提升不同故障状态下诊断结果的可靠性。 相似文献
14.
Shigemitsu Okabe Michio Yamada Shigekatsu Sato Etsunori Mori 《Electrical Engineering in Japan》2000,130(1):21-29
The bushing of a transformer is one part of the transformer system, but is as vital as the transformer itself because it forms a part of the main circuit. Deterioration and abnormal condition of the bushing possibly cause its destruction, shortage of the main circuit to the Earth, and fire in the systems, so that diagnosis of the bushings is thus very important. At present, mainly visual inspection from outside of the bushing is carried out. Inspection of the inside condition of the bushing by dissolved gas analysis of the inside oil is done only as sampling for selected bushings because it is difficult due to the sealed construction of the bushings. Therefore, a simple diagnostic method for bushings has been expected for a long time. In Eastern Europe, the RVM (Return Voltage Measurement) method based on scanning the polarization spectra was applied to the oil–paper insulation systems inside the transformer as a diagnostic method. In this paper we investigate theoretically the principle of the RVM method applied to bushings with the same oil–paper insulation systems as the transformer by using the equivalent circuit, and the possibility of using this novel diagnostic method for condenser‐type bushings is demonstrated by a model experiment. © 1999 Scripta Technica, Electr Eng Jpn, 130(1): 21–29, 2000 相似文献
15.
Katsunori Miyagi Shigenobu Horii Toshiro Sugimoto 《Electrical Engineering in Japan》1996,116(6):83-94
A new type nonflammable large power transformer system is proposed in which the excellent cooling characteristics and insulation properties of nonflammable perfluorocarbon (PFC) liquid is utilized. In the system, transformer windings are put in an insulating cylinder filled with PFC liquid. The core includes cooling panel through the liquid. The space between the insulating cylinder and tank is filled with compressed SF6 gas. This paper describes the insulation characteristics of main insulation and inter-winding insulation models which simulate the transformer. It is found that (1) higher withstand voltage is expected by means of insulation barriers in the main insulation model; (2) partial discharge in inter-winding insulation model is beginning to behave in a constant electric field strength on the point of 0.1 mm liquid gap length. 相似文献
16.
17.
极性反转是换流变压器出线结构复合绝缘的一种特殊工作状态,极性反转时由于空间电荷作用可导致绝缘介质内部及界面处电场畸变。另一方面,绝缘介质电性能参数是温度的函数,因此温度梯度导致的电性能参数改变同样会影响绝缘结构在极性反转过程中的瞬态电场分布。基于此,为了较准确地模拟复合绝缘结构在考虑温度分布条件下的极性反转瞬态电场,提出应用非线性有限元法对以上2种瞬态电场影响因素进行耦合分析。首先研究了油浸纸复合绝缘体系电性能参数与温度的关系;然后详细介绍了基于非线性有限元法的瞬态电场计算流程,并通过双层同轴复合绝缘结构模型验证了其有效性;最后对实际换流变压器出线装置的油纸-环氧浸渍典型复合绝缘结构建立了二维轴对称仿真计算模型,在考虑材料非线性的条件下对其极性反转瞬态电场变化过程进行了仿真分析。计算结果表明传统模拟方法与考虑材料非线性时的结果存在较大差异,且极性反转过程中复合绝缘结构易出现畸变严重的局部高场强区。 相似文献
18.
Deriving an equivalent circuit of transformers insulation for understanding the dielectric response measurements 总被引:1,自引:0,他引:1
Preventive diagnosis and maintenance of transformers have become more and more popular in recent times in order to improve the reliability of electric power systems. Dielectric testing techniques such as return voltage measurement (RVM) and polarization-depolarization current (PDC) measurement are being investigated as potential tools for condition assessment of transformer insulation. A better understanding and analysis of the dielectric test results are only possible with a clear understanding of the physical behavior of the insulation system in response to moisture and aging. A circuit model, which describes the dielectric behavior of the transformer's main insulation system, has been parameterized in this paper. The values of the parameters of the model have been identified from the dielectric tests. A correlation has been developed between the physical condition of the insulation and the equivalent model parameters that enable a clear and transparent interpretation of the dielectric test results. 相似文献