Effects of CNTs on the hydrogen storage properties of MgH2 and MgH2-BCC composite

MgH₂ with 10 wt.% Ti_0.4Mn_0.22Cr_0.1V_0.28 alloy (termed the BCC alloy for its body centred cubic structure) and 5 wt.% carbon nanotubes (CNTs) were prepared by planetary ball milling, and its hydrogen storage properties were compared with those of the pure MgH₂ and the binary mixture of MgH₂ and the BCC alloy. The sample with CNTs showed considerable improvement in hydrogen sorption properties. Its temperature of desorption was 125 °C lower than for the pure sample and 59 °C lower than for the binary mixture. In addition, the gravimetric capacity of the ternary sample was 6 wt.% at 300 °C and 5.6 wt.% at 250 °C, and it absorbed 90% of this amount at 150 s and 516 s at 300 °C and 250 °C, respectively. It can be hypothesised from the results that the BCC alloy assists the dissociation of hydrogen molecules into hydrogen atoms and also promotes hydrogen pumping into the Mg/BCC interfaces, while the CNTs facilitate access of H-atoms into the interior of Mg grains.     

Comparisons between MgH2- and LiH-containing systems for hydrogen storage applications

The present study compares the dehydrogenation kinetics of (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ and (_LiNH2+LiH)$({\mathrm{LiNH}}_2+\mathrm{LiH})$ systems and their vulnerabilities to the NH₃ emission problem. The (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ and (_LiNH2+LiH)$({\mathrm{LiNH}}_2+\mathrm{LiH})$ mixtures with different degrees of mechanical activation are investigated in order to evaluate the effect of mechanical activation on the dehydrogenation kinetics and NH₃ emission rate. The activation energy for dehydrogenation, the phase changes at different stages of dehydrogenation, and the level of NH₃ emission during the dehydrogenation process are studied. It is found that the (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ mixture has a higher rate for hydrogen release, slower rate for approaching a certain percentage of its equilibrium pressure, higher activation energy, and more NH₃ emission than the (_LiNH2+LiH)$({\mathrm{LiNH}}_2+\mathrm{LiH})$ mixture. On the basis of the phenomena observed, the reaction mechanism for the dehydrogenation of the (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ system has been proposed for the first time. Approaches for further improving the hydrogen storage behavior of the (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ system are discussed in light of the newly proposed reaction mechanism.     

Effect of LiH on hydrogen storage property of MgH2

Recent works showed that the addition of LiBH₄ significantly improves the sorption kinetics of MgH₂, and LiH decomposed from LiBH₄ was supposed to play the catalytic effect on MgH₂. In order to clarify this mechanism, the effect of LiH on the hydriding/dehydriding kinetics and thermodynamics of MgH₂ was systematically investigated. The hydrogenation kinetics of LiH-doped samples, as well as the morphology after several cycles, was similar to those of pure MgH₂, which indicate that Li⁺ had no catalytic effect on the hydrogenation of Mg. Moreover, the addition of LiH strongly retarded the hydrogen desorption of MgH₂ doped with/without Nb₂O₅, and resulted in higher starting temperature of desorption, larger activation energy and larger pressure hysteresis of PCI curves of MgH₂. H₂, HD and D₂ were observed in the desorption products of MgH₂-2LiD, which confirms that H–H exchange indeed occurs between MgH₂ and LiH, hence deteriorate desorption kinetics/thermodynamics of MgH_2. The results implied that the additives containing H⁻ could retard the hydrogen desorption of MgH₂ by H–H exchange effect.     

Porous MgH2/C composite with fast hydrogen storage kinetics

A porous MgH₂/C composite can be synthesized through decomposition of an organo-magnesium precursor under hydrogen pressure. XRD patterns of the porous MgH₂/C composite exhibit a pure MgH₂ phase with a tetragonal structure. The morphology of the resulted samples is significantly dependent on the synthesis temperature and hydrogen pressure. The samples exhibit a rod-like structure and composed of nano-crystallites of MgH₂ with a size of less than 5 nm. TPD spectra of a sample synthesized at 220 °C for 4 h show a remarkable decrease of the onset hydrogen release temperature. Further, this sample also exhibits fast hydrogen adsorption kinetics adsorbing 6 wt % of hydrogen in 3 min at 250 °C. The same amount of hydrogen is adsorbed in 11 min at 200 °C and 40 min at 150 °C, respectively. N₂ physisorption measurements of this sample indicate meso-porosity with a BET surface area of 40.9 m² g⁻¹ and an average pore diameter of 20 nm.     

Pellets of MgH2-based composites as practical material for solid state hydrogen storage

Hydrogenation properties and mechanical stability of pellets made starting from compressed ball-milled MgH₂ powders mixed with catalysts (Nb₂O₅ and graphite) and a binding agent (aluminium powder) have been investigated. Structural characterization with X-ray diffraction and gas–solid reaction kinetic and thermodynamic tests with a Sievert's apparatus have been done on the samples up to 50 hydrogen absorption/desorption (a/d) cycles. The best cycling behaviour and mechanical strength stability have been observed for pellets of catalysed MgH₂ powders added with 5 wt% aluminium annealed in vacuum at 450 °C before starting the a/d cycles. This mechanical stability to cycles has been attributed to the formation of a solid solution of aluminium in magnesium.     

Improvement of hydrogen storage properties in MgH2 catalysed by K2NbF7

The catalytic effects of K₂NbF₇ on the hydrogen storage properties of MgH₂ have been studied for the first time. MgH₂ + 5 wt% K₂NbF₇ has reduced the onset dehydrogenation temperature to 255 °C, which is 75 °C lower than the as-milled MgH₂. For the rehydrogenation kinetic, at 150 °C, MgH₂ + 5 wt% K₂NbF₇ absorbs 4.7 wt% of hydrogen in 30 min whereas the as-milled MgH₂ only absorbs 0.7 wt% of hydrogen under similar condition. For the dehydrogenation kinetic, at 320 °C, the MgH₂ + 5 wt% K₂NbF₇ is able to release 5.2 wt% of hydrogen in 5.6 min as compared to 0.3 wt% by the as-milled MgH₂ under similar condition. Comparatively, the E_a value of MgH₂ + 5 wt% K₂NbF₇ is 96.3 kJ/mol, which is 39 kJ/mol lower compared to the as-milled MgH₂. The MgF₂, the KH and the Nb that are found after the heating process are believed to be the active species that have improved the system properties. It is concluded that the K₂NbF₇ is a good catalyst to improve the hydrogen storage properties of MgH₂.     

Effect of LiBH4 on hydrogen storage property of MgH2

The effect of lithium borohydride (LiBH₄) on the hydriding/dehydriding kinetics and thermodynamics of magnesium hydride (MgH₂) was investigated. It was found that LiBH₄ played both positive and negative effects on the hydrogen sorption of MgH₂. With 10 mol.% LiBH₄ content, MgH₂–10 mol.% LiBH₄ had superior hydrogen absorption/desorption properties, which could absorb 6.8 wt.% H within 1300 s at 200 °C under 3 MPa H₂ and completed desorption within 740 s at 350 °C. However, with the increasing amount of LiBH₄, the hydrogenation/dehydrogenation kinetics deteriorated, and the starting desorption temperature increased and the hysteresis of the pressure-composition isotherm (PCI) became larger. Our results showed that the positive effect of LiBH₄ was mainly attributed to the more uniform powder mixture with smaller particle size, while the negative effect of LiBH₄ might be caused by the H–H exchange between LiBH₄ and MgH₂.     

NiB nanoparticles: A new nickel-based catalyst for hydrogen storage properties of MgH2

In this paper, amorphous NiB nanoparticles were fabricated by chemical reduction method and the effect of NiB nanoparticles on hydrogen desorption properties of MgH₂ was investigated. Measurements using temperature-programmed desorption system (TPD) and volumetric pressure–composition isotherm (PCI) revealed that both the desorption temperature and desorption kinetics have been improved by adding 10 wt% amorphous NiB. For example, the MgH₂–10 wt%NiB mixture started to release hydrogen at 180 °C, whereas it had to heat up to 300 °C to release hydrogen for the pure MgH₂. In addition, a hydrogen desorption capacity of 6.0wt% was reached within 10 min at 300 °C for the MgH₂–10 wt%NiB mixture, in contrast, even after 120 min only 2.0 wt% hydrogen was desorbed for pure MgH₂ under the same conditions. An activation energy of 59.7 kJ/mol for the MgH₂/NiB composite has been obtained from the desorption data, which exhibits an enhanced kinetics possibly due to the additives reduced the barrier and lowered the driving forces for nucleation. Further cyclic kinetics investigation using high-pressure differential scanning calorimetry technique (HP-DSC) indicated that the composite had good cycle stability.     

Influence of metal oxide on LiBH4/2LiNH2/MgH2 system for hydrogen storage properties

In this study, various nanoscale metal oxide catalysts, such as CeO₂, TiO₂, Fe₂O₃, Co₃O₄, and SiO₂, were added to the LiBH₄/2LiNH₂/MgH₂ system by using high-energy ball milling. Temperature programmed desorption and MS results showed that the Li–Mg–B–N–H/oxide mixtures were able to dehydrogenate at much lower temperatures. The order of the catalytic effect of the studied oxides was Fe₂O₃ > Co₃O₄ > CeO₂ > TiO₂ > SiO₂. The onset dehydrogenation temperature was below 70 °C for the samples doped with Fe₂O₃ and Co₃O₄ with 10 wt.%. More than 5.4 wt.% hydrogen was released at 140 °C. X-ray diffraction indicated that the addition of metal oxides inhibited the formation of Mg(NH₂)₂ during ball milling processes. It is thought that the changing of the ball milling products results from the interaction of oxide ions in metal oxide catalysts with hydrogen atoms in MgH₂. The catalytic effect depends on the activation capability of oxygen species in metal oxides on hydrogen atoms in hydrides.     

Changes of hydrogen storage properties of MgH2 induced by heavy ion irradiation

In order to understand the influence of defect zones on desorption behavior of _MgH2${\mathrm{MgH}}_2$, Xe 120 keV ion irradiation of this material has been performed. DSC, SEM measurements, and SRIM calculations have been used to characterize induced modifications and its influence on the hydrogen desorption behavior of _MgH2${\mathrm{MgH}}_2$. We have demonstrated that the near-surface area of _MgH2${\mathrm{MgH}}_2$ plays the crucial role in hydrogen desorption kinetics. DSC analysis provides clear picture of vacancies influence on H diffusion and desorption in _MgH2${\mathrm{MgH}}_2$, and points out that there is possibility to control the thermodynamic parameters by controlled ion bombardment.     

Improving hydrogen storage properties of MgH2 by addition of alkali hydroxides

In this study, alkali hydroxides (NaOH, LiOH, KOH) were attempted as new-type catalytic additives to improve the hydrogen storage properties of MgH₂ by ball milling. It is shown that the additives readily react with the MgH₂ to form perovskite-structured NaMgH₃ and KMgH₃, but not the LiMgH₃. Although the in-situ formed perovskite hydrides remain stable during hydriding/dehydriding cycles, both NaMgH₃ and KMgH₃ show predominant catalytic role on the hydriding and dehydriding of MgH₂. In contrast, the LiOH modified MgH₂ presents much inferior sorption kinetics because of the absence of LiMgH₃. The catalytic mechanism of perovskite hydrides can be explained by the high hydrogen mobility in the perovskite structure. This study shows that such cheap hydroxides could be used as efficient catalysts to improve the hydrogen storage properties of high-capacity metal hydrides and complex hydrides.     

Effect of CO on hydrogen storage performance of 2LiNH2 + MgH2 system

(2LiNH₂ + MgH₂) system is one of the most promising hydrogen storage materials due to its suitable operation temperature and high reversible hydrogen storage capacity. In studies and applications, impurities such as CO, CO₂, O₂, N₂ and CH₄ are potential factors which may influence its performance. In the present work, hydrogen containing 1 mol% CO is employed as the hydrogenation gas source, and directly participates in the reaction to investigate the effect of CO on the hydrogen sorption properties of (2LiNH₂ + MgH₂) system. The results indicate that the hydrogen capacity of the (Mg(NH₂)₂ + 2LiH) system declines from 5 wt.% to 3.45 wt.% after 6 cycles of hydrogenation and dehydrogenation, and can not restore to its initial level when use purified hydrogen again. The hydrogen desorption kinetics decreases obviously and the dehydrogenation activation energy increases from 133.35 kJ/mol to 153.35 kJ/mol. The main reason for these is that two new products Li₂CN₂ and MgO appear after (2LiNH₂ + MgH₂) react with CO. They are formed on the surface of materials particles, which may not only cause a permanent loss of NH²⁻, but also prevent the substance transmission during the reaction process. After re-mechanically milling, both kinetics and dehydrogenation activation energy can be recovered to the initial level.     

The hydrogen storage properties and reaction mechanism of the MgH2-NaAlH4 composite system

In this study, we report the hydrogen absorption/desorption properties and reaction mechanism of the MgH₂-NaAlH₄ (4:1) composite system. This composite system showed improved dehydrogenation performance compared with that of as-milled NaAlH₄ and MgH₂ alone. The dehydrogenation process in the MgH₂-NaAlH₄ composite can be divided into four stages: NaAlH₄ is first reacted with MgH₂ to form a perovskite-type hydride, NaMgH₃ and Al. In the second dehydrogenation stage, the Al phase reacts with MgH₂ to form Mg₁₇Al₁₂ phase accompanied with the self-decomposition of the excessive MgH₂. NaMgH₃ goes on to decompose to NaH during the third dehydrogenation stage, and the last stage is the decomposition of NaH. Kissinger analysis indicated that the apparent activation energy, E_A, for the MgH₂-relevent decomposition in MgH₂-NaAlH₄ composite was 148 kJ/mol, which is 20 kJ/mol less than for as-milled MgH₂ (168 kJ/mol). X-ray diffraction patterns indicate that the second, third, and fourth stages are fully reversible. It is believed that the formation of Al₁₂Mg₁₇ phase during the dehydrogenation process alters the reaction pathway of the MgH₂-NaAlH₄ (4:1) composite system and improves its thermodynamic properties.     

Fundamental environmental reactivity testing and analysis of the hydrogen storage material 2LiBH4·MgH2

While the storage of hydrogen for portable and stationary applications is regarded as critical in bringing PEM fuel cells to commercial acceptance, little is known of the environmental exposure risks posed in utilizing condensed phase chemical storage options as in complex hydrides. It is thus important to understand the effect of environmental exposure of metal hydrides in the case of accident scenarios. Simulated tests were performed following the United Nations standards to test for flammability and water reactivity in air for a destabilized lithium borohydride and magnesium hydride system in a 2 to 1 molar ratio respectively. It was determined that the mixture acted similarly to the parent, lithium borohydride, but at slower rate of reaction seen in magnesium hydride. To quantify environmental exposure kinetics, isothermal calorimetry was utilized to measure the enthalpy of reaction as a function of exposure time to dry and humid air, and liquid water. The reaction with liquid water was found to increase the heat flow significantly during exposure compared to exposure in dry or humid air environments. Calorimetric results showed the maximum normalized heat flow of the fully charged material was 6 mW/mg under liquid phase hydrolysis; and 14 mW/mg for the fully discharged material also occurring under liquid phase hydrolysis conditions.     

Effects of SnO2 on hydrogen desorption of MgH2

The hydrogen desorption properties of Magnesium Hydride (MgH₂) ball milled with cassiterite (SnO₂) have been investigated by X-ray powder diffraction and thermal analysis. Milling of pure MgH₂ leads to a reduction of the desorption temperature (up to 60 K) and of the activation energy, but also to a reduction of the quantity of desorbed hydrogen, referred to the total MgH₂ present, from 7.8 down to 4.4 wt%. SnO₂ addition preserves the beneficial effects of grinding on the desorption kinetics and limits the decrease of desorbed hydrogen. Best tradeoff – activation energy lowered from 175 to 148 kJ/mol and desorbed hydrogen, referred to the total MgH₂ present, lowered from 7.8 to 6.8 wt% – was obtained by co-milling MgH₂ with 20 wt% SnO₂.     

Hydrogen storage properties of nanostructured MgH2/TiH2 composite prepared by ball milling under high hydrogen pressure

Nanostructured MgH₂/0.1TiH₂ composite was synthesized directly from Mg and Ti metal by ball milling under an initial hydrogen pressure of 30 MPa. The synthesized composite shows interesting hydrogen storage properties. The desorption temperature is more than 100 °C lower compared to commercial MgH₂ from TG-DSC measurements. After desorption, the composite sample absorbs hydrogen at 100 °C to a capacity of 4 mass% in 4 h and may even absorb hydrogen at 40 °C. The improved properties are due to the catalyst and nanostructure introduced during high pressure ball milling. From the PCI results at 269, 280, 289 and 301 °C, the enthalpy change and entropy change during the desorption can be determined according to the van’t Hoff equation. The values for the MgH₂/0.1TiH₂ nano-composite system are 77.4 kJ mol⁻¹ H₂ and 137.5 J K⁻¹ mol⁻¹ H₂, respectively. These values are in agreement with those obtained for a commercial MgH₂ system measured under the same conditions. Nanostructure and catalyst may greatly improve the kinetics, but do not change the thermodynamics of the materials.     

Synergistic catalytic effect of SrTiO3 and Ni on the hydrogen storage properties of MgH2

Study on the synergistic catalytic effect of the SrTiO₃ and Ni on the improvement of the hydrogen storage properties of the MgH₂ system has been carried out. The composites have been prepared using ball milling method and comparisons on the hydrogen storage properties of the MgH₂ – Ni and MgH₂ – SrTiO₃ composites have been presented. The MgH₂ – 10 wt% SrTiO₃ – 5 wt% Ni composite is found to has a decomposition temperature of 260 °C with a total decomposition capacity of 6 wt% of hydrogen. The composite is able to absorb 6.1 wt% of hydrogen in 1.3 min (320 °C, 27 atm of hydrogen). At 150 °C, the composite is able to absorb 2.9 wt% of hydrogen in 10 min under the pressure of 27 atm of hydrogen. The composite has successfully released 6.1 wt% of hydrogen in 13.1 min with a total dehydrogenation of 6.6 wt% of hydrogen (320 °C). The apparent activation energy, E_a, for decomposition of SrTiO₃-doped MgH₂ reduced from 109.0 kJ/mol to 98.6 kJ/mol after the addition of 5 wt% Ni. The formation of Mg₂Ni and Mg₂NiH₄ as the active species help to boost the performance of the hydrogen storage properties of the MgH₂ system. Observation of the scanning electron microscopy images suggested the catalytic role of the SrTiO₃ additive is based on the modification of composite microstructure.     

Reversible hydrogen sorption and kinetics of hydrogen storage tank based on MgH2 modified by TiF4 and activated carbon

By doping with 5 wt % TiF₄ and activated carbon (AC), onset and main dehydrogenation temperatures of MgH₂ significantly reduce (ΔT = 138 and 109 °C, respectively) with hydrogen capacity of 4.4 wt % H₂. Up-scaling to storage tank begins with packing volume and sample weight of 28.8 mL and ～14.5 g, respectively, and continues to 92.6 mL and ～60.5–67 g, respectively. Detailed hydrogen sorption mechanisms and kinetics of the tank tightly packed with four beds of MgH₂TiF₄-AC (～60.5 g) are investigated. De/rehydrogenation mechanisms are detected by three temperature sensors located at different positions along the tank radius, while hydrogen permeability is benefited by stainless steel mesh sheets and tube inserted in the hydride beds. Fast desorption kinetics of MgH₂TiF₄-AC tank at ～275–283 °C, approaching to onset dehydrogenation temperature of the powder sample (272 °C) suggests comparable performances of laboratory and tank scales. Hydrogen desorption (T = 300 °C and P(H₂) = 1 bar) and absorption (T = 250 °C and P(H₂) = 10–15 bar) of MgH₂TiF₄-AC tank provide gravimetric and volumetric capacities during the 1^st-2nd cycles of 4.46 wt % H₂ and 28 gH₂/L, respectively, while those during the 3^rd-15th cycles are up to 3.62 wt % H₂ and 23 gH₂/L, respectively. Due to homogeneous heat transfer along the tank radius, de/rehydrogenation kinetics superior at the tank center and degrading forward the tank wall can be due to poor hydrogen permeability. Particle sintering and/or agglomeration upon cycling yield deficient hydrogen content reproduced.     

Hydrogen storage properties of nano-structured 0.65MgH2/0.35ScH2

The intermetallic compound Mg_0.65Sc_0.35 was found to form a nano-structured metal hydride composite system after a (de)hydrogenation cycle at temperatures up to 350 °C. Upon dehydrogenation phase separation occurred forming Mg-rich and Sc-rich hydride phases that were clearly observed by SEM and TEM with the Sc-rich hydride phase distributed within Mg/MgH₂-rich phase as nano-clusters ranging in size from 40 to 100 nm. The intermetallic compound Mg_0.65Sc_0.35 showed good hydrogen uptake, ca. 6.4 wt.%, in the first charging cycle at 150 °C and in the following (de)hydrogenation cycles, a reversible hydrogen capacity (up to 4.3 wt.%) was achieved. Compared to the as-received MgH₂, the composite had faster cycling kinetics with a significant reduction in activation energy E_a from 159 ± 1 kJ mol⁻¹ to 82 ± 1 kJ mol⁻¹ (as determined from a Kissinger plot). Two-dehydrogenation events were observed by DSC and pressure–composition-isotherm (PCI) measurements, with the main dehydrogenation event being attributed to the Mg-rich hydride phase. Furthermore, after the initial two cycles the hydrogen storage capacity remained unchanged over the next 55 (de)hydrogenation cycles.     

Ab initio calculations of MgH2, MgH2:Ti and MgH2:Co compounds

The understanding of hydrogen bonding in magnesium and magnesium based alloys is an important step toward its prospective use. In the present study, a density functional theory (DFT) based, full-potential augmented plane waves method of calculation, extended with local orbitals (FP-APW+lo), was used to investigate the stability of MgH₂ and MgH₂:TM (TM = Ti and Co) 10 wt % alloys and the influence of this alloying on hydrogen storage properties of MgH₂ compound. Effects of a possible spin polarisation induced in the system by transition metal (TM) ions were considered too. It has been found that TM-H bonding is stronger than the Mg–H bond, but at the same time it weakens other bonds in the second and third coordination around a TM atom, which leads to overall destabilization of the MgH₂ compound. Due to a higher number of d-electrons, this effect is more pronounced for Co alloying, where in addition, the spin polarisation has a noticeable and stabilising influence on the compound structure.