采用新型馈电结构的双频宽带导航天线设计

基于新馈电结构,设计了一款覆盖全球四大卫星导航系统的双频宽带贴片天线。采用了一种四分八馈电线路,以8个同轴馈电探针两两相连的方式将两路天线馈电信号合为一路,有效简化了馈电网络的复杂性,同时保证了天线辐射的增益、带宽和轴比性能。该双频辐射贴片单元采用正八边形层叠式结构设计,并在每个天线单元边缘对称添加两组矩形调谐单元,有效增加了天线辐射的波束带宽。该双频天线单元在高频1.482~1.617 GHz（波束带宽155 MHz）和低频1.191~1.252 GHz(波束带宽61 MHz）频段范围内,都能保证良好的辐射增益;高低频的3 dB轴比带宽为-130°~130°,具备良好的圆极化性能。经实物样机对比测试分析,实测结果与仿真结果基本吻合。     

一种单层双频宽带GNSS测量型天线设计

基于单介质层结构,设计了一款双频宽带全球卫星导航系统(GNSS)测量型天线,天线采用单层高性能轻质复合材料作为双频微带天线共用的辐射介质基板。双频辐射贴片单元采用共面齿轮结构设计,并在天线单元外围设置一系列短路销钉来有效改善天线轴比带宽、低仰角辐射增益等参数,四馈点馈电技术和宽带耦合相移馈电网络的应用保证了天线相位中心稳定度更加可靠。设计结果表明,该双频天线单元大于等于5 d Bi的辐射增益带宽均大于245 MHz,高低频3 d B轴比带宽分别为-76°~76°和-116°~116°,低仰角90°增益滑落均小于11.5 d B,经实物样机对比测试分析,实测结果与仿真结果基本吻合。实测频谱显示,该天线工作频段覆盖目前在运行的四大导航系统全部工作频点,较好满足GNSS精确测量与定位系统终端设备应用需求。     

一种三馈圆极化微带天线的设计与制作

提出了一种应用于无线局域网（WLAN）通信的三馈圆极化微带天线。天线在2300～2600MHz频带内实现圆极化辐射。天线馈电网络采用三功分馈电,增加了轴比带宽;馈电网络和附加的寄生贴片展宽了阻抗带宽;延伸天线介质衬底增大了波束宽度。仿真与实测结果吻合良好。测量结果表明,天线的阻抗带宽达到46.8%（VSWR〈2）,轴比带宽达到12.2%（AR〈3dB）。     

一种新型双频双圆极化复合微带天线设计

针对空间微波能量收集的应用场景,提出了一种微带线行波激励的双端口双频双圆极化复合微带天线。该天线由一个工作在低频段的微带圆环和一个工作在高频段的微带圆片复合而成,分别由两种不同的正交十字缝隙耦合馈电,采用微带线级联依次相差90°顺序旋转四馈电实现圆极化,通过对称性结构设计,分别从两个不同端口输入获得双圆极化性能。实验结果表明：在880～960 MHz和1.85～2.45 GHz频带内S11<-10 dB,阻抗相对带宽分别为8.7%和30%;在885～920 MHz和1.86～2.43 GHz频带内轴比小于3 dB,圆极化相对带宽分别为4%和29%;天线的方向性在工作频段内良好,在低频段增益达到5.4 dB,在高频段增益达到7.7 dB。该天线结构紧凑且加工简单,为双端口双频双圆极化天线的研究与设计提供了新思路。     

一种基于电调移相器的可重构天线

设计并实现了一种基于反射式移相器的极化可重构天线。该天线使用一对交叉摆放的领结型振子作为辐射单元,并在馈电网络中通过两路移相器调整双馈端口间的相位差实现线极化、左旋圆极化和右旋圆极化模式之间的切换。通过加载匹配枝节的方法扩展了反射式移相器的移相范围,提高了移相器的移相精度,降低了天线圆极化模式带内的轴比。所设计天线的中心频率为5.4 GHz,在线极化模式下10 dB 阻抗带宽为990 MHz,在圆极化模式下10 dB 阻抗带宽分别为760 MHz 和850 MHz,3 dB 轴比带宽分别为510 MHz和480 MHz。该天线在频带内具有稳定的波束方向图,其平均增益为5.3 dB,并且具有27 dB 的主极化-交叉极化隔离。最终的实测结果与仿真结果基本一致,表明该天线具有良好的性能。     

一种LTCC叠层耦合馈电圆极化微带天线的设计

设计了一种低温共烧陶瓷(LTCC)低剖面圆极化叠层耦合微带贴片天线.该天线采用层叠结构,在辐射基板正面采用分形的辐射贴片来降低天线尺寸并拓展带宽;在馈电层基板正面开“十字”槽,在其反面通过使用威尔金森功分器加移相器网络对“十字”槽馈电,使得耦合馈电端口的正交电场相位差90°来实现微带天线的圆极化.该天线设计剖面厚度仅3 mm.仿真结果显示该天线工作于1.268 GHz时,实现阻抗带宽超过60 MHz,天线的轴比小于1.5 dB且增益达到5 dB.     

一种小型化宽带圆极化微带天线的设计

设计并加工了一种采用同轴背馈方式馈电的小型化宽带圆极化微带天线。针对单点馈电微带天线轴比带宽窄的问题,通过增加馈电网络对天线辐射贴片进行双点馈电以展宽轴比带宽,得到了良好的效果。馈电网络根据带状线理论设计,利用U形接地板巧妙地实现了宽带天线的结构小型化。通过对辐射贴片的双点馈电获得了令人满意的电压驻波比带宽和良好的圆极化性能。通过仿真和实际测试表明,该天线VSWR≤2的带宽达到了30％,3dB圆极化带宽约为26％,同时频带内天线的增益达到4dB。     

层叠北斗双频微带天线圆极化比较研究

分别采用切角技术、双馈电技术以及将两者相结合的方法设计了三款用于北斗卫星系统的层叠结构的双频圆 极化微带天线，天线均工作于1258-1278MHz 和1575-1609MHz 频段。通过HFSS 仿真对比发现，在其他指标均能满足要求的 前提下，采用切角和双馈技术相结合的方法不但能实现圆极化，而且其轴比优于单一的切角技术和双馈技术。三款天线在 各工作频段内反射损耗均小于-10dB，且高低频段增益均在3dB 以上。     

一种单空气介质层GNSS测量型天线设计

本文设计了一款单空气介质层测量型有源贴片天线,天线结构采用单层空气介质作为全球卫星导航系统(GNSS)贴片天线高低频段的电场辐射层,通过对高频贴片外边缘锯齿化处理和低频贴片内边缘锯齿化接地以及其外边缘设置锯齿辐射单元,使天线整体尺寸减小约20%。通过HFSS软件优化设计,实现了GNSS天线的成本低、体积小、增益高、轴比频带较宽、圆极化性能好等特点。同时,天线辐射贴片结构在设计上满足高低频相位中心高程差较小。本文所设计天线满足覆盖四大在运行卫星导航系统的高低信号频段,并且采用对称的四馈针馈电技术使得天线表现出良好的圆极化性能和相位中心稳定性,尤其适合于GNSS精确测量与精准定位系统终端设备。     

一种具有高隔离度的双频双圆极化卫星通信天线

 提出了一种新型的用于卫星通信的双频双圆极化多层微带贴片天线.该天线采用兰格耦合器正交馈电,分别在420±1.5MHz和450MHz±1.5MH的收发频率实现右旋和左旋圆极化辐射,且满足单一天线收发双工的通信要求;采用耦合贴片馈电方式和附加集总电路滤波网络,有效地改善了两端口之间的收发隔离度.此外,该天线采用高介电常数的介质基板减小了天线尺寸.兰格耦合器采用曲折线技术减小了馈电网络的结构尺寸(约74.6%).仿真和实测结果吻合良好,在工作频带内收发隔离度大于40dB,VSWR小于2.0,增益大于3dBc,0dB增益宽度及3dB轴比宽度均达到80°.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first