Solid-State Synthesis of Te-Doped Mg<Subscript>2</Subscript>Si

Te-doped Mg₂Si (Mg₂Si:Te _m , m = 0, 0.01, 0.02, 0.03, 0.05) alloys were synthesized by a solid-state reaction and mechanical alloying. The electronic transport properties (Hall coefficient, carrier concentration, and mobility) and thermoelectric properties (Seebeck coefficient, electrical conductivity, thermal conductivity, and figure of merit) were examined. Mg₂Si was synthesized successfully by a solid-state reaction at 673 K for 6 h, and Te-doped Mg₂Si powders were obtained by mechanical alloying for 24 h. The alloys were fully consolidated by hot-pressing at 1073 K for 1 h. All the Mg₂Si:Te _m samples showed n-type conduction, indicating that the electrical conduction is due mainly to electrons. The electrical conductivity increased and the absolute value of the Seebeck coefficient decreased with increasing Te content, because Te doping increased the electron concentration considerably from 10¹⁶ cm⁻³ to 10¹⁸ cm⁻³. The thermal conductivity did not change significantly on Te doping, due to the much larger contribution of lattice thermal conductivity over the electronic thermal conductivity. Thermal conduction in Te-doped Mg₂Si was due primarily to lattice vibrations (phonons). The thermoelectric figure of merit of intrinsic Mg₂Si was improved by Te doping.     

Thermoelectric Properties of NdGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> Prepared by CS<Subscript>2</Subscript> Sulfurization

Ternary rare-earth sulfides NdGd_1+x S₃, where 0 ≤ x ≤ 0.08, were prepared by sulfurizing Ln₂O₃ (Ln = Nd, Gd) with CS₂ gas, followed by reaction sintering. The sintered samples have full density and homogeneous compositions. The Seebeck coefficient, electrical resistivity, and thermal conductivity were measured over the temperature range of 300 K to 950 K. All the sintered samples exhibit a negative Seebeck coefficient. The magnitude of the Seebeck coefficient and the electrical resistivity decrease systematically with increasing Gd content. The thermal conductivity of all the sintered samples is less than 1.9 W K⁻¹ m⁻¹. The highest figure of merit ZT of 0.51 was found in NdGd_1.02S₃ at 950 K.     

Thermoelectric Properties of Ag-doped Mg<Subscript>2</Subscript>Ge Thin Films Prepared by Magnetron Sputtering

Silver doped p-type Mg₂Ge thin films were grown in situ at 773 K using magnetron co-sputtering from individual high-purity Mg and Ge targets. A sacrificial base layer of silver of various thicknesses from 4 nm to 20 nm was initially deposited onto the substrate to supply Ag atoms, which entered the growing Mg₂Ge films by thermal diffusion. The addition of silver during film growth led to increased grain size and surface microroughness. The carrier concentration increased from 1.9 × 10¹⁸ cm⁻³ for undoped films to 8.8 × 10¹⁸ cm⁻³ for the most heavily doped films, but it did not reach saturation. Measurements in the temperature range of T = 200–650 K showed a positive Seebeck coefficient for all the films, with maximum values at temperatures between 400 K and 500 K. The highest Seebeck coefficient of the undoped film was 400 μV K⁻¹, while it was 280 μV K⁻¹ for the most heavily doped film at ∼400 K. The electrical conductivity increased with silver doping by a factor of approximately 10. The temperature effects on power factors for the undoped and lightly doped films were very limited, while the effects for the heavily doped films were substantial. The power factor of the heavily doped films reached a non-optimum value of ∼10⁻⁵ W cm⁻¹ K⁻² at 700 K.     

Thermoelectric Properties of Zr<Subscript>3</Subscript>Mn<Subscript>4</Subscript>Si<Subscript>6</Subscript> and TiMnSi<Subscript>2</Subscript>

The Seebeck coefficient, electrical resistivity, and thermal conductivity of Zr₃Mn₄Si₆ and TiMnSi₂ were studied. The crystal lattices of these compounds contain relatively large open spaces, and, therefore, they have fairly low thermal conductivities (8.26 Wm⁻¹ K⁻¹ and 6.63 Wm⁻¹ K⁻¹, respectively) at room temperature. Their dimensionless figures of merit ZT were found to be 1.92 × 10⁻³ (at 1200 K) and 2.76 × 10⁻³ (at 900 K), respectively. The good electrical conductivities and low Seebeck coefficients might possibly be due to the fact that the distance between silicon atoms in these compounds is shorter than that in pure semiconductive silicon.     

Thermoelectric Properties of Sb-Doped Mg<Subscript>2</Subscript>Si<Subscript>0.3</Subscript>Sn<Subscript>0.7</Subscript>

Mg₂(Si_0.3Sn_0.7)_1−y Sb _y (0 ≤ y ≤ 0.04) solid solutions were prepared by a two-step solid-state reaction method combined with the spark plasma sintering technique. Investigations indicate that the Sb doping amount has a significant impact on the thermoelectric properties of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y compounds. As the Sb fraction y increases, the electron concentration and electrical conductivity of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y first increase and then decrease, and both reach their highest value at y = 0.025. The sample with y = 0.025, possessing the highest electrical conductivity and one of the higher Seebeck coefficient values among all the samples, has the highest power factor, being 3.45 mW m⁻¹ K⁻² to 3.69 mW m⁻¹ K⁻² in the temperature range of 300 K to 660 K. Meanwhile, Sb doping can significantly reduce the lattice thermal conductivity (κ _ph) of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y due to increased point defect scattering, and κ _ph for Sb-doped samples is 10% to 20% lower than that of the nondoped sample for 300 K < T < 400 K. Mg₂(Si_0.3Sn_0.7)_0.975Sb_0.025 possesses the highest power factor and one of the lower κ _ph values among all the samples, and reaches the highest ZT value: 1.0 at 640 K.     

Synthesis and Characterization of <Emphasis Type="Italic">p</Emphasis>-Type Pb<Subscript>0.5</Subscript>Sn<Subscript>0.5</Subscript>Te Thermoelectric Power Generation Elements by Mechanical Alloying

A mechanical alloying (MA) process to transform elemental powders into solid Pb_0.5Sn_0.5Te with thermoelectric functionality comparable to melt-alloyed material is described. The room-temperature doping level and mobility as well as temperature-dependent electrical conductivity, Seebeck coefficient, and thermal conductivity are reported. Estimated values of lattice thermal conductivity (0.7 W m⁻¹ K⁻¹) are lower than some reports of functional melt-alloyed PbSnTe-based material, providing evidence that MA can engender the combination of properties resulting in highly functional thermoelectric material. Though doping level and Sn composition have not been optimized, this material exhibits a ZT value >0.5 at 550 K.     

Influence of Doping on Structural and Thermoelectric Properties of AgSbSe<Subscript>2</Subscript>

A series of samples with nominal compositions of AgSb_1−x Sn _x Se₂ (with x = 0.0, 0.1, 0.2, and 0.3) and AgSbSe_2−y Te _y (with y = 0.0, 0.25, 0.5, 0.75, and 1.0) were prepared. The crystal structure of both single crystals and polycrystalline samples was analyzed using x-ray and neutron diffractometry. The electrical conductivity, thermal conductivity, and Seebeck coefficient were measured within the temperature range from 300 K to 700 K. In contrast to intrinsic AgSbSe₂, samples doped with Sn and Te exhibit apparent semiconducting properties (E _g = 0.3 eV to 0.5 eV), lower electrical conductivity, and higher values of the Seebeck coefficient for a small amount of Sn (x = 0.1). Further doping leads to decrease of the thermoelectric power and increase of the electrical conductivity. In order to explain electron transport behavior observed in pure and doped AgSbSe₂, electronic structure calculations were performed by the Korringa–Kohn–Rostoker method with coherent potential approximation (KKR–CPA).     

Thermoelectric Properties of Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript> Skutterudite Materials with Partial In Filling and Excess In Additions

The properties of Co₄Sb₁₂ with various In additions were studied. X-ray diffraction revealed the presence of the pure δ-phase of In_0.16Co₄Sb₁₂, whereas impurity phases (γ-CoSb₂ and InSb) appeared for x = 0.25, 0.40, 0.80, and 1.20. The homogeneity and morphology of the samples were observed by Seebeck microprobe and scanning electron microscopy, respectively. All the quenched ingots from which the studied samples were cut were inhomogeneous in the axial direction. The temperature dependence of the Seebeck coefficient (S), electrical conductivity (σ), and thermal conductivity (κ) was measured from room temperature up to 673 K. The Seebeck coefficient of all In-added Co₄Sb₁₂ materials was negative. When the filler concentration increases, the Seebeck coefficient decreases. The samples with In additions above the filling limit (x = 0.22) show an even lower Seebeck coefficient due to the formation of secondary phases: InSb and CoSb₂. The temperature variation of the electrical conductivity is semiconductor-like. The thermal conductivity of all the samples decreases with temperature. The central region of the In_0.4Co₄Sb₁₂ ingot shows the lowest thermal conductivity, probably due to the combined effect of (a) rattling due to maximum filling and (b) the presence of a small amount of fine-dispersed secondary phases at the grain boundaries. Thus, regardless of the non-single-phase morphology, a promising ZT (S ² σT/κ) value of 0.96 at 673 K has been obtained with an In addition above the filling limit.     

Thermoelectric Properties of SnO<Subscript>2</Subscript> Ceramics Doped with Sb and Zn

Polycrystalline SnO₂-based samples (Sn_0.97−x Sb_0.03Zn _x O₂, x = 0, 0.01, 0.03) were prepared by solid-state reactions. The thermoelectric properties of SnO₂ doped with Sb and Zn were investigated from 300 K to 1100 K. X-ray diffraction (XRD) analysis revealed all XRD peaks of all the samples as identical to the rutile structure, except for the x = 0.03 sample, which had a small amount of Zn₂SbO₄ as a secondary phase. We found that the power factor of the x = 0.03 sample was significantly improved due to the simultaneous increase in the electrical conductivity and the Seebeck coefficient. A power factor value of ∼2 × 10⁻⁴ W m⁻¹ K⁻² was obtained for the x = 0.03 sample at 1060 K, 126% higher than that for the undoped sample.     

First-Principles and Experimental Studies of Y-Doped Mg<Subscript>2</Subscript>Si Prepared Using Field-Activated Pressure-Assisted Synthesis

The thermoelectric properties of Y-doped (1000 ppm, 2000 ppm, 3000 ppm) Mg₂Si fabricated using field-activated pressure-assisted synthesis (FAPAS) have been characterized using measurements of electrical resistivity (ρ), Seebeck coefficient (S), and thermal conductivity (κ) at temperatures ranging from 285 K to 810 K. The Y-doped Mg₂Si samples were n-type in the measured temperature range. A first-principles calculation revealed that the Y atoms were expected to be primarily located at Mg sites. In sample doped with 2000 ppm Y, which exhibited the best electrical and thermal conductivity, the absolute value of the Seebeck coefficient increased in the temperature range of 320 K to 680 K, being higher than that of undoped Mg₂Si. Moreover, this sample exhibited a higher level of electrical conductivity and a higher power factor. In addition, introduction of Y decreased the thermal conductivity appreciably, indicating that Y dopants are favorable for improving the properties of Mg₂Si.     

Thermoelectric Properties of Co<Subscript>4</Subscript>Sn<Subscript>6</Subscript>Se<Subscript>6</Subscript> Ternary Skutterudites

A ternary ordered variant of the skutterudite structure, the Co₄Sn₆Se₆ compound, was prepared. Polycrystalline samples were prepared by a modified ceramic method. The electrical conductivity, the Seebeck coefficient and the thermal conductivity were measured over a temperature range of 300–800 K. The undoped Co₄Sn₆Se₆ compound was of p-type electrical conductivity and had a band gap E _g of approximately 0.6 eV. The influence of transition metal (Ni and Ru) doping on the thermoelectric properties was studied. While the thermal conductivity was significantly lowered both for the undoped Co₄Sn₆Se₆ compound and for the doped compounds, as compared with the Co₄Sb₁₂ binary skutterudite, the calculated ZT values were improved only slightly.     

Microstructure and Thermoelectric Properties of <Emphasis Type="Italic">n</Emphasis>- and <Emphasis Type="Italic">p</Emphasis>-Type Doped Mg<Subscript>2</Subscript>Sn Compounds Prepared by the Modified Bridgman Method

Mg₂Sn compounds were prepared by the modified vertical Bridgman method, and were doped with Bi and Ag to obtain n- and p-type materials, respectively. Excess Mg was also added to some of the ingots to compensate for the loss of Mg during the preparation process. The Mg₂Sn samples were characterized by x-ray diffraction (XRD) and scanning electron microscopy (SEM), and their power factors were calculated from the Seebeck coefficient and electrical conductivity, measured from 80 K to 700 K. The sample prepared with 4% excess Mg, which contains a small amount of Mg₂Sn + Mg eutectic phase, had the highest power factor of 12 × 10⁻³ W m⁻¹ K⁻² at 115 K, while the sample doped with 2% Ag, in which a small amount of eutectics also exists, has a power factor of 4 × 10⁻³ W m⁻¹ K⁻² at 420 K.     

Thermoelectric Properties of Heavily Doped <Emphasis Type="Italic">n</Emphasis>-Type SrTiO<Subscript>3</Subscript> Bulk Materials

Three Ta-doped strontium titanates were prepared as potential candidates for n-type thermoelectric oxides. The purity of the polycrystalline samples of SrTi_1−x Ta _x O₃ (x = 0.05 to 0.14) were characterized by means of powder x-ray diffraction and electron probe micro analysis (EPMA). We present the results of Seebeck coefficient, electrical conductivity, and thermal conductivity measurements performed at high temperatures.     

Synthesis and Electronic Properties of the Misfit Layer Compound [(PbSe)<Subscript>1.00</Subscript>]<Subscript>1</Subscript>[MoSe<Subscript>2</Subscript>]<Subscript>1</Subscript>

An ultralow-thermal-conductivity compound with the ideal formula [(PbSe)_1.00]₁[MoSe₂]₁ has been successfully crystallized across a range of compositions. The lattice parameters varied from 1.246 nm to 1.275 nm, and the quality of the observed 00ℓ diffraction patterns varied through the composition region where the structure crystallized. Measured resistivity values ranged over an order of magnitude, from 0.03 Ω m to 0.65 Ω m, and Seebeck coefficients ranged from −181 μV K⁻¹ to 91 μV K⁻¹ in the samples after the initial annealing to form the basic structure. Annealing of samples under a controlled atmosphere of selenium resulted in low conductivities and large negative Seebeck coefficients, suggesting an n-doped semiconductor. Scanning transmission electron microscopy cross-sections confirmed the interleaving of bilayers of PbSe with Se-Mo-Se trilayers. High-angle annular dark-field images revealed an interesting volume defect, where PbSe grew through a region where a layer of MoSe₂ would be expected in the perfect structure. Further studies are required to correlate the density of these defects with the observed electrical properties.     

Thermoelectric Properties of Ca-Filled CoSb<Subscript>3</Subscript>-Based Skutterudites Synthesized by Mechanical Alloying

Ca _z Co_4−x (Fe/Mn) _x Sb₁₂ skutterudites were prepared by mechanical alloying and hot pressing. The phases of mechanically alloyed powders were identified as γ-CoSb₂ and Sb, but they were transformed to δ-CoSb₃ by annealing at 873 K for 100 h. All specimens had a positive Hall coefficient and Seebeck coefficient, indicating p-type conduction by holes as majority carriers. For the binary CoSb₃, the electrical conductivity behaved like a nondegenerate semiconductor, but Ca-filled and Fe/Mn-doped CoSb₃ showed a temperature dependence of a degenerate semiconductor. While the Seebeck coefficient of intrinsic CoSb₃ increased with temperature and reached a maximum at 623 K, the Seebeck coefficient increased with increasing temperature for the Ca-filled and Fe/Mn-doped specimens. Relatively low thermal conductivity was obtained because fine particles prepared by mechanical alloying lead to phonon scattering. The thermal conductivity was reduced by Ca filling and Fe/Mn doping. The electronic thermal conductivity was increased by Fe/Mn doping, but the lattice thermal conductivity was decreased by Ca filling. Reasonable thermoelectric figure-of-merit values were obtained for Ca-filled Co-rich p-type skutterudites.     

Electrodeposition and Thermoelectric Characteristics of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> and Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> Films for Thermopile Sensor Applications

A thermopile sensor was processed on a glass substrate by electrodeposition of n-type bismuth telluride (Bi-Te) and p-type antimony telluride (Sb-Te) films. The n-type Bi-Te film electrodeposited at −50 mV in a 50 mM electrolyte with a Bi/(Bi + Te) mole ratio of 0.5 exhibited a Seebeck coefficient of −51.6 μV/K and a power factor of 7.1 × 10⁻⁴ W/K² · m. The p-type Sb-Te film electroplated at 20 mV in a 70 mM solution with an Sb/(Sb + Te) mole ratio of 0.9 exhibited a Seebeck coefficient of 52.1 μV/K and a power factor of 1.7 × 10⁻⁴ W/K² · m. A thermopile sensor composed of 196 pairs of the p-type Sb-Te and the n-type Bi-Te thin-film legs exhibited sensitivity of 7.3 mV/K.     

Improvement of Thermoelectric Power Factor of Hydrothermally Prepared Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Compared with its Solvothermally Prepared Counterpart

We report on the successful hydrothermal synthesis of Bi_0.5Sb_1.5Te₃, using water as the solvent. The products of the hydrothermally prepared Bi_0.5 Sb_1.5Te₃ were hexagonal platelets with edges of 200–1500 nm and thicknesses of 30–50 nm. Both the Seebeck coefficient and electrical conductivity of the hydrothermally prepared Bi_0.5Sb_1.5Te₃ were larger than those of the solvothermally prepared counterpart. Hall measurements of Bi_0.5Sb_1.5Te₃ at room temperature indicated that the charge carrier was p-type, with a carrier concentration of 9.47 × 10¹⁸ cm⁻³ and 1.42 × 10¹⁹ cm⁻³ for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively. The thermoelectric power factor at 290 K was 10.4 μW/cm K² and 2.9 μW/cm K² for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively.     

Thermoelectric Properties of Zintl Compound YbZn<Subscript>2</Subscript>Sb<Subscript>2</Subscript> with Mn Substitution in Anionic Framework

The thermoelectric properties of the Zintl compound YbZn₂Sb₂ with isoelectronic substitution of Zn by Mn in the anionic (Zn₂Sb₂)²⁻ framework have been studied. The p-type YbZn_2−x Mn _x Sb₂ (0.0 ≤ x ≤ 0.4) samples were prepared via melting followed by annealing and hot-pressing. Thermoelectric property measurement showed that the Mn substitution effectively lowered the thermal conductivity for all the samples, while it significantly increased the Seebeck coefficient for x < 0.2. As a result, a dimensionless figure of merit ZT of approximately 0.61 to 0.65 was attained at 726 K for x = 0.05 to 0.15, compared with the ZT of ~0.48 in the unsubstituted YbZn₂Sb₂.     

Thermoelectric Properties of <Emphasis Type="Italic">In Situ</Emphasis> Formed Bi<Subscript>0.85</Subscript>Sb<Subscript>0.15</Subscript>/Bi-Rich Particles Composite

A Bi-15 at.%Sb alloy, homogenized by equal channel angular extrusion (ECAE) at T = 523 K, has been treated just above its solidus temperature, causing segregation of a secondary Bi-rich phase at the grain boundaries. This process results in an in situ composite. The thermoelectric properties of the composite have been measured in the range of 5 K < T < 300 K. The results are compared with those of the homogeneous alloy. The presence of a Bi-rich phase improves the Seebeck coefficient at T < 50 K, and enhances the electrical conductivity by a factor of 1.4 at T = 300 K up to a factor of 3.4 at T = 50 K; unfortunately, the thermal conductivity also increases by about 50% in the same temperature range. As a result, the figure of merit, Z, is slightly suppressed above T = 110 K, but increases at lower temperatures, reaching a peak value of 4.2 × 10⁻³ K⁻¹ at T = 90 K. The power factor considerably increases over the whole temperature range, rendering this material suitable as the n-type leg of a cryogenic thermoelectric generator for cold energy recovery in a liquefied natural gas plant.     

Preparation and Thermoelectric Properties of La-Doped SrTiO<Subscript>3</Subscript> Ceramics

Single-phase polycrystalline La _x Sr_1−x TiO₃ (x = 0, 0.04, 0.06, 0.08, and 0.12) ceramics were prepared by the conventional solid-state reaction method using high-activity hydroxides as the raw materials. The electrical conductivity of all the samples increased with increasing x value and decreased with measurement temperature, while the thermal conductivity decreased with increasing x value and measurement temperature. The La_0.12Sr_0.88TiO₃ sample showed the lowest thermal conductivity of 2.45 W m⁻¹ K⁻¹ at 873 K and the largest ZT of 0.28 at 773 K. The present work revealed that hydroxides with high activity as raw materials are beneficial to improve the thermoelectric properties, especially to decrease the thermal conductivity.