Syngas yield during pyrolysis and steam gasification of paper

Main characteristics of gaseous yield from steam gasification have been investigated experimentally. Results of steam gasification have been compared to that of pyrolysis. The temperature range investigated were 600–1000 °C in steps of 100 °C. Results have been obtained under pyrolysis conditions at same temperatures. For steam gasification runs, steam flow rate was kept constant at 8.0 g/min. Investigated characteristics were evolution of syngas flow rate with time, hydrogen flow rate and chemical composition of syngas, energy yield and apparent thermal efficiency. Residuals from both processes were quantified and compared as well. Material destruction, hydrogen yield and energy yield is better with gasification as compared to pyrolysis. This advantage of the gasification process is attributed mainly to char gasification process. Char gasification is found to be more sensitive to the reactor temperature than pyrolysis. Pyrolysis can start at low temperatures of 400 °C; however char gasification starts at 700 °C. A partial overlap between gasification and pyrolysis exists and is presented here. This partial overlap increases with increase in temperature. As an example, at reactor temperature 800 °C this overlap represents around 27% of the char gasification process and almost 95% at reactor temperature 1000 °C.     

Characteristic of hydrogen and syngas evolution from gasification and pyrolysis of rubber

The characteristics of syngas evolution during pyrolysis and gasification of waste rubber have been investigated. A semi-batch reactor was used for the thermal decomposition of the material under various conditions of pyrolysis and high temperature steam gasification. The results are reported at two different reactor temperatures of 800 and 900 °C and at constant steam gasifying agent flow rate of 7.0 g/min and a fixed sample mass. The characteristics of syngas were evaluated in terms of syngas flow rate, hydrogen flow rate, syngas yield, hydrogen yield and energy yield. Gasification resulted in 500% increase in hydrogen yield as compared to pyrolysis at 800 °C. However, at 900 °C the increase in hydrogen was more than 700% as compared to pyrolysis. For pyrolysis conditions, increase in reactor temperature from 800 to 900 °C resulted in 64% increase in hydrogen yield while for gasification conditions a 124% increase in hydrogen yield was obtained. Results of syngas yield, hydrogen yield and energy yield from the rubber sample are evaluated with that obtained from woody biomass samples, namely hard wood and wood chips. Rubber gasification yielded more energy at the 900 °C as compared to biomass feedstock samples. However, less syngas and less hydrogen were obtained from rubber than the biomass samples at both the temperatures reported here.     

Characteristics of syngas from co-gasification of polyethylene and woodchips

Gasification of polyethylene (PE) and woodchips (WC) mixtures have been investigated in a semi-batch reactor, using high temperature steam as the gasifying agent. The reactor temperature was maintained at 900 °C. The ratio of PE–WC was varied from 0% to 100% in 20% intervals. Characteristics of syngas were evaluated based on the yield of syngas, hydrogen, energy, ethylene, total hydrocarbons and apparent thermal efficiency of the process. Results show that properties of syngas evolved during gasification of PE–WC blends cannot be determined from the weighted average syngas properties obtained from separate gasification of WC and PE. Superior results in terms of syngas yield, hydrogen yield, total hydrocarbons yield, energy yield and apparent thermal efficiency from PE–WC blends were obtained as compared to expected weighed average yields from gasification of individual components. Results confirm synergistic interaction between PE and WC during high temperature steam gasification of these mixtures. These results also provide the importance of mixing two or more compounds on the performance of stream gasification of wastes.     

Hydrogen production from polystyrene pyrolysis and gasification: Characteristics and kinetics

Polystyrene (PS) pyrolysis and gasification have been examined in a semi-batch reactor at temperatures of 700, 800 and 900 °C. Characteristic differences between pyrolysis and gasification of polystyrene (PS) have been evaluated with specific performance focus on the evolution of syngas flow rate, evolution of hydrogen flow rate, evolution of output power, syngas yield, hydrogen yield, energy yield, apparent thermal efficiency and syngas quality. Behavior of PS under either pyrolysis or gasification processes is compared to that of char based sample, such as paper and cardboard. In contrast to char based materials, PS gasification yielded less syngas, hydrogen and energy than pyrolysis at 700 °C. However, the gasification of PS yielded more syngas, hydrogen and energy than pyrolysis at 900 °C temperature. Gasification of PS is affected by reactor temperature more than PS pyrolysis. Syngas, hydrogen and energy yield increased exponentially with temperature in case of gasification. However, syngas and energy yield increased linearly with temperature having rather a mild slope in the case of pyrolysis. Pyrolysis resulted in higher syngas quality at all temperatures. Kinetics of hydrogen evolution from the PS pyrolysis is introduced. The Coats and Redfern method was used to determine the kinetic parameters, activation energy (E_act), pre-exponential factor (A) and reaction order (n). The model used is the nth order chemical reaction model. Kinetic parameters have been determined for three slow heating rates, namely 8, 10 and 12 °C/min. The average values obtained from the three heating rate experiments were used to compare the model with the experimental data.     

Syngas production from catalytic gasification of waste polyethylene: Influence of temperature on gas yield and composition

The catalytic steam gasification of waste polyethylene (PE) from municipal solid waste (MSW) to produce syngas (H₂ + CO) with NiO/γ-Al₂O₃ as catalyst in a bench-scale downstream fixed bed reactor was investigated. The influence of the reactor temperature on the gas yield, gas composition, steam decomposition, low heating value (LHV), cold gas efficiency and carbon conversion efficiency was investigated at the temperature range of 700–900 °C, with a steam to waste polyethylene ratio of 1.33. Over the ranges of experimental conditions examined, NiO/γ-Al₂O₃ catalyst revealed better catalytic performance as a view of increasing product gas yield and of decreasing char and liquid yields in the presence of steam. Higher temperature resulted in more H₂ and CO production, higher carbon conversion efficiency and product gas yield. The highest syngas (H₂ + CO) content of 64.35 mol%, the highest H₂ content of 36.98 mol%, and the highest CO content of 27.37 mol%, were achieved at the highest temperature level of 900 °C. Syngas produced with a H₂/CO molar ratio in the range of 0.83–1.35, was highly desirable as feedstock for Fischer–Tropsch synthesis for the production of transportation fuels.     

High temperature steam gasification of wastewater sludge

High temperature steam gasification is one of the most promising, viable, effective and efficient technology for clean conversion of wastes to energy with minimal or negligible environmental impact. Gasification can add value by transforming the waste to low or medium heating value fuel which can be used as a source of clean energy or co-fired with other fuels in current power systems. Wastewater sludge is a good source of sustainable fuel after fuel reforming with steam gasification. The use of steam is shown to provide value added characteristics to the sewage sludge with increased hydrogen content as well total energy. Results obtained on the syngas properties from sewage sludge are presented here at various steam to carbon ratios at a reactor temperature of 1173 K. Effect of steam to carbon ratio on syngas properties are evaluated with specific focus on the amounts of syngas yield, syngas composition, hydrogen yield, energy yield, and apparent thermal efficiency. The apparent thermal efficiency is similar to cold gas efficiency used in industry and was determined from the ratio of energy in syngas to energy in the solid sewage sludge feedstock. A laboratory scale semi-batch type gasifier was used to determine the evolutionary behavior of the syngas properties using calibrated experiments and diagnostic facilities. Results showed an optimum steam to carbon ratio of 5.62 for the range of conditions examined here for syngas yield, hydrogen yield, energy yield and energy ratio of syngas to sewage sludge fuel. The results show that steam gasification provided 25% increase in energy yield as compared to pyrolysis at the same temperature.     

Hydrogen-rich gas from catalytic steam gasification of municipal solid waste (MSW): Influence of catalyst and temperature on yield and product composition

In the present study the catalytic steam gasification of MSW to produce hydrogen-rich gas or syngas (H₂ + CO) with calcined dolomite as a catalyst in a bench-scale downstream fixed bed reactor was investigated. The influence of the catalyst and reactor temperature on yield and product composition was studied at the temperature range of 750–950 °C, with a steam to MSW ratio of 0.77, for weight hourly space velocity of 1.29 h⁻¹. Over the ranges of experimental conditions examined, calcined dolomite revealed better catalytic performance, at the presence of steam, tar was completely decomposed as temperature increases from 850 to 950 °C. Higher temperature resulted in more H₂ and CO production, higher carbon conversion efficiency and dry gas yield. The highest H₂ content of 53.29 mol%, and the highest H₂ yield of 38.60 mol H₂/kg MSW were observed at the highest temperature level of 950 °C, while, the maximum H₂ yield potential reached 70.14 mol H₂/kg dry MSW at 900 °C. Syngas produced by catalytic steam gasification of MSW varied in the range of 36.35–70.21 mol%. The char had a highest ash content of 84.01% at 950 °C, and negligible hydrogen, nitrogen and sulphur contents.     

Analysis of syngas production rate in empty fruit bunch steam gasification with varying control factors

Biomass gasification is a prevailing approach for mitigating irreversible fossil fuel depletion. In this study, palm empty fruit bunch (EFB) was steam-gasified in a fixed-bed, batch-fed gasifier, and the effect of four control factors—namely torrefaction temperature for EFB pretreatment, gasification temperature, carrier-gas flow rate, and steam flow rate—on syngas production were investigated. The results showed that steam flow rate is the least influential control factor, with no effect on syngas composition or yield. The gasification temperature of biomass significantly affects the composition of syngas generated during steam gasification, and the H₂/CO ratio increases by approximately 50% with an increase in temperature ranging from 680 °C to 780 °C. The higher H₂/CO ratio at a lower gasification temperature increased the energy density of the combustible constituents of the syngas by 3.43%.     

Hydrogen and syngas production from sewage sludge via steam gasification

High temperature steam gasification is an attractive alternative technology which can allow one to obtain high percentage of hydrogen in the syngas from low-grade fuels. Gasification is considered a clean technology for energy conversion without environmental impact using biomass and solid wastes as feedstock. Sewage sludge is considered a renewable fuel because it is sustainable and has good potential for energy recovery. In this investigation, sewage sludge samples were gasified at various temperatures to determine the evolutionary behavior of syngas characteristics and other properties of the syngas produced. The syngas characteristics were evaluated in terms of syngas yield, hydrogen production, syngas chemical analysis, and efficiency of energy conversion. In addition to gasification experiments, pyrolysis experiments were conducted for evaluating the performance of gasification over pyrolysis. The increase in reactor temperature resulted in increased generation of hydrogen. Hydrogen yield at 1000 °C was found to be 0.076 g_gas g_sample⁻¹. Steam as the gasifying agent increased the hydrogen yield three times as compared to air gasification. Sewage sludge gasification results were compared with other samples, such as, paper, food wastes and plastics. The time duration for sewage sludge gasification was longer as compared to other samples. On the other hand sewage sludge yielded more hydrogen than that from paper and food wastes.     

Hydrogen-rich gas from catalytic steam gasification of biomass in a fixed bed reactor: Influence of particle size on gasification performance

The catalytic steam gasification of biomass was carried out in a lab-scale fixed bed reactor in order to evaluate the effects of particle size at different bed temperatures on the gasification performance. The bed temperature was varied from 600 to 900 °C and the biomass was separated into five different size fractions (below 0.075 mm, 0.075–0.15 mm, 0.15–0.3 mm, 0.3–0.6 mm and 0.6–1.2 mm). The results show that with decreasing particle size, the dry gas yield, carbon conversion efficiency and H₂ yield increased, and the content of char and tar decreased. And the differences due to particle sizes in gasification performance practically disappear as the higher temperature bound is approached. Hydrogen and carbon monoxide contents in the produced gas increase with decreasing particle size at 900 °C, reaching to 51.2% and 22.4%, respectively.     

Integrated catalytic adsorption (ICA) steam gasification system for enhanced hydrogen production using palm kernel shell

This paper investigates the integrated catalytic adsorption (ICA) steam gasification of palm kernel shell for hydrogen rich gas production using pilot scale fluidized bed gasifier under atmospheric condition. The effect of temperature (600–750 °C) and steam to biomass ratio (1.5–2.5 wt/wt) on hydrogen (H₂) yield, product gas composition, gas yield, char yield, gasification and carbon conversion efficiency, and lower heating values are studied. The results show that H₂ hydrogen composition of 82.11 vol% is achieved at temperature of 675 °C, and negligible carbon dioxide (CO₂) composition is observed at 600 °C and 675 °C at a constant steam to biomass ratio of 2.0 wt/wt. In addition, maximum H₂ yield of 150 g/kg biomass is observed at 750 °C and at steam to biomass ratio of 2.0 wt/wt. A good heating value of product gas which is 14.37 MJ/Nm³ is obtained at 600 °C and steam to biomass ratio of 2.0 wt/wt. Temperature and steam to biomass ratio both enhanced H₂ yield but temperature is the most influential factor. Utilization of adsorbent and catalyst produced higher H₂ composition, yield and gas heating values as demonstrated by biomass catalytic steam gasification and steam gasification with in situ CO₂ adsorbent.     

Thermal conversion efficiency of producing hydrogen enriched syngas from biomass steam gasification

This paper presents the results from an experimental study on the energy conversion efficiency of producing hydrogen enriched syngas through uncatalyzed steam biomass gasification. Wood pellets were gasified using a 100 kW_th fluidized bed gasifier at temperatures up to 850 °C. The syngas hydrogen concentration and cold gas efficiency were found to increase with both bed temperature and steam to biomass weight ratio, reaching a maximum of 51% and 124% respectively. The overall energy conversion to syngas (based on heating value) also increased with bed temperature but was inversely proportional to the steam to biomass ratio. The maximum energy conversion to syngas was found to be 68%. The conversion of energy to hydrogen (by heating value) increased with gasifier temperature and gas residence time, but was found to be independent of the S/B ratio. The maximum conversion of all energy sources to hydrogen was found to be 25%.     

Characteristics of cardboard and paper gasification with CO2

Evolutionary behavior of syngas chemical composition and yield have been examined for paper and cardboard at three different temperatures of 800, 900 and 1000 °C using CO₂ as the gasifying agent at constant flow rate. Specifically the evolution of syngas chemical composition with time has been investigated. Pyrolysis of the sample was dominant at the beginning of the gasification process as observed from the high initial devolatilization of the sample followed by char gasification of material to form syngas for a long period of time. Results provided the role of gasification temperature on kinetics of the CO₂ gasification process. Increase in gasification temperature provided increased conversion of the sample material to syngas. Thus the sample conversion to syngas was low at the low temperature of 800 °C while at elevated temperatures of 900 and 1000 °C substantial enhancement of the kinetics process occurred. The evolution of extensive reaction rate of carbon-monoxide was calculated. Results show that increase in temperature increased the extensive reaction rate of carbon-monoxide. The global behavior of syngas chemical composition examined at three different temperatures revealed a peak in concentration of H₂ to exhibit after few minutes into the gasification that changed with gasification temperature. At 800 °C gasification temperature peak in H₂ was displayed at 3 min into gasification while it decreased to only 2 min, approximately, at gasification temperatures of 900 and 1000 °C. The effect of reactor temperature on CO mole fraction has also been examined. Increase in the gasification temperature enhances the mole fraction of CO yields. This is attributed to the increase in forward reaction rate of the Boudouard reaction (C+CO₂2CO). The results show important role of CO₂ gas for the gasification of wastes and low grade fuels to clean syngas.     

Application of response surface methodology to assess the combined effect of operating variables on high-pressure coal gasification for H2-rich gas production

Coal gasification was performed by means of a high-pressure fixed bed gasifier fitted with a solids feeding system in continuous mode, using oxygen and steam as gasifying agents. The main aim of the paper was to assess the combined effects of the operating variables (temperature, oxygen and steam concentrations) on high-pressure coal gasification. To this end a face centered central composite design (FCCCD) based on response surface methodology (RSM) was used. The response variables studied were: H₂, CO and syngas production, H₂/CO ratio, cold gas efficiency (η), and carbon conversion (X). The study was carried out at temperatures of 900, 950 and 1000 °C, using oxygen concentrations of 5, 10 and 15 vol.%, and steam concentrations of 25, 40 and 55 vol.%. The gasification temperature was found to be the most influential variable, with high temperatures leading to an increase in all the response variables studied. An increase in the oxygen content of the gasifying agent led to a decrease in H₂ and CO production, and cold gas efficiency, whilst carbon conversion was favoured. An increase in steam concentration, on the other hand, favoured the production of H₂ and syngas production, whereas CO production underwent a reduction; cold gas efficiency and carbon conversion were observed to increase. Response surface methodology (RSM) revealed the effects of interaction between the operating variables, which would not have been identified by the traditional “one-factor-at-a-time” method. The models developed successfully fitted the experimental results for all the response variables studied.     

Low temperature steam gasification to produce hydrogen rich gas from kitchen food waste: Influence of steam flow rate and temperature

Large amount of food waste is generated from Indian kitchens and disposing off such a large amount possesses a great challenge in terms of environmental degradation and viable food waste processing technology. In this work, steam gasification was tested as an alternative viable technology to process the kitchen food waste. Preliminary study was carried out at low temperature on steam gasification in a fixed bed reactor to study the influence of steam flow rate (SFR) and temperature on the syngas yield, syngas composition, hydrogen yield. Performance parameters such as carbon conversion efficiency (CCE), and apparent thermal efficiency (ATE) are also calculated. Steam flow rates are varied from 0.125 mL/min to 0.75 mL/min and the temperatures are varied from 700 °C to 800 °C. The highest hydrogen yield is obtained at 0.5 mL/min SFR and 800 °C temperature and its highest value is 1.2 m³/kg. The highest value of performance parameters, CCE and ATE are found to be 63% and 1.8.     

Thermodynamic optimization of biomass gasification for decentralized power generation and Fischer–Tropsch synthesis

In recent years, biomass gasification has emerged as a viable option for decentralized power generation, especially in developing countries. Another potential use of producer gas from biomass gasification is in terms of feedstock for Fischer–Tropsch (FT) synthesis – a process for manufacture of synthetic gasoline and diesel. This paper reports optimization of biomass gasification process for these two applications. Using the non–stoichometric equilibrium model (SOLGASMIX), we have assessed the outcome of gasification process for different combinations of operating conditions. Four key parameters have been used for optimization, viz. biomass type (saw dust, rice husk, bamboo dust), air or equivalence ratio (AR = 0, 0.2, 0.4, 0.6, 0.8 and 1), temperature of gasification (T = 400, 500, 600, 700, 800, 900 and 1000 °C), and gasification medium (air, air–steam 10% mole/mole mixture, air–steam 30%mole/mole mixture). Performance of the gasification process has been assessed with four measures, viz. molar content of H₂ and CO in the producer gas, H₂/CO molar ratio, LHV of producer gas and overall efficiency of gasifier. The optimum sets of operating conditions for gasifier for FT synthesis are: AR = 0.2–0.4, Temp = 800–1000 °C, and gasification medium as air. The optimum sets of operating conditions for decentralized power generation are: AR = 0.3–0.4, Temp = 700–800 °C with gasification medium being air. The thermodynamic model and methodology presented in this work also presents a general framework, which could be extended for optimization of biomass gasification for any other application.     

Performance improvement of direct carbon fuel cell by introducing catalytic gasification process

In this paper, the effects of catalytic gasification on the solid oxide electrolyte DCFC (direct carbon fuel cell) performance are experimentally investigated and analyzed using K, Ca, Ni as catalyst in carbon black and controlling the temperatures of cell and carbon black at 750 °C and 700-1000 °C, respectively. The average power densities are 976, 1473 and 1543 W m⁻² respectively for 900, 950 and 1000 °C pure carbon black gasification. Catalytic gasification improves the DCFC performance significantly. For the same performance of pure carbon black, the gasification temperatures decrease about 200, 130 and 150 °C with K, Ca and Ni additives, respectively. The catalytic effects for carbon black gasification with CO₂ are: K > Ni > Ca. For typical identical temperature DCFC operating at 750 °C, the power densities of 0.7 V discharging are 1477, 1034 and 1123 W m⁻² for the carbon black with K, Ca and Ni additives, respectively. It is possible to reduce the operation temperature of DCFC to the medium temperature range of solid oxide electrolyte (600-800 °C) by introducing catalytic gasification process.     

Hydrogen-rich gas production from biomass steam gasification in an updraft fixed-bed gasifier combined with a porous ceramic reformer

This paper investigates the hydrogen-rich gas produced from biomass employing an updraft gasifier with a continuous biomass feeder. A porous ceramic reformer was combined with the gasifier for producer gas reforming. The effects of gasifier temperature, equivalence ratio (ER), steam to biomass ratio (S/B), and porous ceramic reforming on the gas characteristic parameters (composition, density, yield, low heating value, and residence time, etc.) were investigated. The results show that hydrogen-rich syngas with a high calorific value was produced, in the range of 8.10–13.40 MJ/Nm³, and the hydrogen yield was in the range of 45.05–135.40 g H₂/kg biomass. A higher temperature favors the hydrogen production. With the increasing gasifier temperature varying from 800 to 950 °C, the hydrogen yield increased from 74.84 to 135.4 g H₂/kg biomass. The low heating values first increased and then decreased with the increased ER from 0 to 0.3. A steam/biomass ratio of 2.05 was found as the optimum in the all steam gasification runs. The effect of porous ceramic reforming showed the water-soluble tar produced in the porous ceramic reforming, the conversion ratio of total organic carbon (TOC) contents is between 22.61% and 50.23%, and the hydrogen concentration obviously higher than that without porous ceramic reforming.     

The aluminum silicate catalyst effect on efficiency of energy yield in gasification of paper-reject sludge

This research investigated the mineral aluminum silicate catalyst effect on the enhancement of energy yield efficiency and reduction of the tar yield concentration in the gasification of paper-reject sludge. Experimental results indicated that the energy yield efficiency is enhanced by the tested mineral catalyst. When gasification temperature operated at 600 °C, the lower heating value (LHV) of syngas increased significantly from 8.66 MJ/Nm³ to 13.38 MJ/Nm³ with an increase in aluminum silicate catalyst addition from 0% to 20%. The energy density of syngas also increased from 0.53 to 0.82. This implied that the energy utilization of syngas produced by a low temperature catalytic gasification could increase approximately 1.5 times the energy content of paper-reject sludge. The tar reduction efficiency could reach approximately 50% which was also proportional to the catalyst addition ratio. In summary, the aluminum silicate catalyst can help to improve the efficiency of tar reduction and energy yield in a low temperature catalytic gasification of paper-reject sludge.     

Steam gasification of energy crops of high cultivation potential in Poland to hydrogen-rich gas

In the paper energy crops of considerable cultivation potential in Poland, namely: Salix viminalis, Helianthus tuberosus, Sida hermaphrodita, Spartina pectinata, Andropogon gerardi and Miscanthus X giganteus were tested in terms of steam gasification reactivity of biomass chars, as well as yields and composition of product gas in steam gasification and lime-enhanced steam gasification in a laboratory scale fixed bed reactor at 650 °, 700 ° and 800 °C.The highest value of reactivity for 50% of carbon conversion, R₅₀, was observed for Sida hermaphrodita, regardless the process temperature.Application of CaO for in-situ CO₂ capture in steam gasification of biomass chars resulted in hydrogen content increase at 650 °C to the levels comparable with the ones reached at 800 °C without carbonation reaction. Also hydrogen and total gas yields increased in tests of lime-enhanced gasification.