Effect of different corundum sources on microstructure and properties of Al2O3–Cr2O3 refractories

Al₂O₃–Cr₂O₃ refractories are completely substitutional solid solutions and exhibit better corrosion and abrasion resistance. To enable the comprehensive utilization of it, the microstructure and properties of Al₂O₃–Cr₂O₃ samples with different corundum sources were investigated in this study. The starting sources of corundum sources included sintered tabular corundum, fused white corundum, or brown corundum with minor impurities of β-Al₂O₃ and TiO₂. The results of mechanical test showed that the introduction of white corundum deteriorates the physical structure, while brown corundum acts in an opposite manner. The optimum bonding strength of the Al₂O₃–Cr₂O₃ brick was reached by combining white and brown corundum, whereby rapid neck growth occurred via surface diffusion during solid-phase sintering.     

Enhanced oxidation resistance of low-carbon MgO–C refractories with Al3BC3–Al antioxidants: A synergistic effect

The synergistic effects of Al₃BC₃–Al antioxidants on optimizing the oxidation resistance of low-carbon MgO–C refractories were investigated. The results indicated that the oxidation index and rate constant of low-carbon MgO–C refractories with optimized Al₃BC₃–Al additions were 13% and 1.10 × 10⁻⁴ cm² min⁻¹ at 1400°C for 3 h, respectively, which is much lower than that of Al or Al₃BC₃ containing ones. Single Al₃BC₃ is not a suitable antioxidant for low-carbon MgO–C refractories; however, if Al₃BC₃ was initially protected and Al reacted as the antioxidant, enhanced oxidation resistance at high temperature can be achieved. The formation of dense MgO–MgAl₂O₄–Mg₃B₂O₆ layer contributed to superior oxidation resistance, and the temperature for the generation of this layer was as low as 1100°C due to liquid and vapor phase–assisted reactions with Al₃BC₃–Al. Furthermore, a self-repairing function was achieved at 1600°C with the combination of Al₃BC₃–Al additions in spite of the faster oxidation rate.     

Thermal shock resistance of mullite–cordierite refractories

Abstract

The effect of aggregate size on the strength degradation of mullite-cordierite specimens subjected to thermal shock has been studied. Strength degradation of shocked specimens is shown to depend on the aggregate size, on the preshock strength of sintered specimens, and on cordierite content. Retained strength after shocking increased in specimens prepared from small aggregates owing to the higher initial strength. These specimens contained lower cordierite content as a result of the increased dissociation of cordierite brought about by decreasing the aggregate size.     

Corrosion modeling of magnesia aggregates in contact with CaO–MgO–SiO2 slags

Ladle refining is an efficient process for improvement of quality of steel on secondary metallurgy under harsh conditions. Magnesia refractories with high purity are important raw materials for ladle lining in high-quality steel production. However, the penetration by CaO–MgO–SiO₂ slags damages magnesia refractories, which considerably limits their service life. Abundant grain boundaries in magnesia create channels for slag penetration and lead to the destruction of the structure. The effect of the microstructure on the slag corrosion behavior of magnesia aggregates requires further systematic investigation. In this study, a corrosion model was established to describe the slag penetration process of magnesia aggregates. The effects of the grain-boundary size and slag CaO/SiO₂ mass ratio (C/S ratio) on slag penetration were investigated, and the possibility of the microstructure optimization of magnesia aggregates was discussed. The results indicated that magnesia aggregates exhibited excellent slag resistance for slag with a C/S ratio above 1.5 or even 2.0. When the slag C/S ratio was lower than 1.5, the dissolution rate of magnesia decreased more rapidly with the increase in the slag C/S ratio. In addition, the much smaller grain-boundary size increased the slag penetration resistance by promoting the formation of a dense isolation layer and inhibiting further penetration processes. The calculation results agreed well with the experimental results, suggesting that the corrosion model is promising for predicting slag corrosion.     

Microstructure and mechanical properties of multi-walled carbon nanotubes containing Al2O3–C refractories with addition of polycarbosilane

Carbon nanotubes (CNTs) are a promising reinforcement for fabricating Al₂O₃–C refractories. However, CNTs are prone to agglomerate or react with antioxidants or reactive gaseous phases such as Al (g), Si (g) and SiO (g), etc. at high temperatures. To overcome the problems above, polycarbosilane (PCS) and multi-walled carbon nanotubes (MWCNTs) were firstly mixed with micro-alumina powder in a liquid medium and then incorporated into Al₂O₃–C refractories. Then the microstructure and mechanical properties of Al₂O₃–C refractories fired in the temperature range from 800 °C to 1400 °C were investigated in this work. The results showed that the MWCNTs were well dispersed in the specimens with addition of PCS in contrast to the specimens without PCS due to the PCS adsorption on the surface of MWCNTs during the mixing process. And the mechanical properties, such as cold modulus of rupture (CMOR), flexural modulus (FM), forces and displacements of Al₂O₃–C refractories with PCS were much higher than those without PCS, which was attributed to more homogeneous dispersion of MWCNTs, more residual MWCNTs as well as different morphologies of ceramic whiskers. Meanwhile, the oxidation resistance of Al₂O₃–C refractories with PCS was improved greatly, which was supposed that the in situ formed SiC_xO_y coating prevented the oxidation of MWCNTs to some extent.     

Slag resistance mechanism of MgO–Mg2SiO4–SiC–C refractories containing porous multiphase aggregates

The slag resistance of MgO–SiC–C (MSC) refractories should be improved because of the mismatch in the thermal expansion coefficient between the aggregates and matrix, as well as the defects caused by the affinity between periclase and slag. In this study, MgO–Mg₂SiO₄–SiC–C (MMSC) refractories were prepared using porous multiphase MgO–Mg₂SiO₄ (M-M₂S) aggregates to replace dense fused magnesia aggregates. Compared to MSC, the slag penetration index of MMSC decreased by 43.5%. The structure of the porous aggregates increased the surface roughness, and the multiphase composition of the aggregates decreased the mismatch of the thermal expansion coefficient with the matrix, thus reducing debonding between the aggregates and matrix. The aggregates and matrix in the MMSC formed an interlocking structure, which bound them more tightly to improve the slag resistance. The slag viscosity at different depths from the initial slag/refractory interface was calculated using the Ribond model. The M-M₂S aggregates increased Si_xO_y^z− in the slag, which increased the slag polymerization and slag viscosity. The aggregates and matrix in the MMSC reacted with the slag to form high melting point phases, which reduced the channel of the slag. In addition, the penetration depth and velocity derived from the Washburn Equation were modified for the CaO–SiO₂–Al₂O₃–MgO–FeO slag and magnesia based refractory to accurately evaluate slag penetration.     

In situ hot elastic modulus evolution of MgO–C refractories containing Al,Si or Al–Mg antioxidants

Metals and alloys (such as Al, Si, Al–Mg and Al–Si) are commonly added to MgO–C refractory bricks as antioxidants due to their effectiveness to prevent carbon oxidation (in the 600–1400 °C range) and their low cost. These additives act at different temperatures and react with refractory components and gases in the environment, inducing significant changes in the resultant microstructure and affecting the overall thermo-mechanical performance of these products. This work addresses the evaluation of physical properties, cold and hot mechanical resistance, as well as in situ hot elastic modulus (E) measurements in the temperature range of 30–1400 °C for MgO–C bricks containing antioxidants (Al, Si or Al–Mg alloy) in a reducing atmosphere. Cured and fired samples of the designed formulations were evaluated throughout 1 or 2 heating-cooling cycles. Despite the improved mechanical behavior (higher cold crushing strength and hot modulus of rupture) of the antioxidant-containing formulations, compared to the additive-free MgO–C sample, the interaction of the selected additives with the refractory components and CO_(g) led to a generation of phases (i.e., Al₄C₃, Al₂O₃, SiC, SiO₂, MgAl₂O₄) that could not be well accommodated in the microstructure. Consequently, the in situ E drop was observed during cooling (mainly below 600 °C) of the antioxidant-containing sample due to crack and flaw formations. Si and Al–Mg were the most promising antioxidants, whereas the Al-containing composition showed the highest E damage level after two heating/cooling cycles up to 1400 °C for cured samples. Based on the elastic modulus profiles with the temperature, the results also indicated the best working conditions for these ceramic materials.     

Structure and viscosity of CaO–Al2O3–B2O3–BaO slags with varying mass ratio of BaO to CaO

The structure of CaO–Al₂O₃–B₂O₃–BaO glassy slags with varying mass ratio of BaO to CaO has been investigated by Raman spectroscopy, ¹¹B and ²⁷Al magic angle spinning nuclear magnetic resonance (MAS-NMR) spectroscopy and atomic pair distribution function (PDF). ¹¹B MAS-NMR spectra reveal the dominant coordination of boron as trigonal. Both simulations on ¹¹B MAS-NMR spectra and Raman spectroscopy indicate the presence of orthoborate as the primary borate group with a few borate groups with one bridging oxygen and minor four-coordinated boron sites. ²⁷Al MAS-NMR and PDF show the Al coordination as tetrahedral. Raman spectral study shows that the transverse vibration of Al^IV–O–Al^IV and Al^IV–O–B^III, stretching vibration of aluminate structural units and vibration of orthoborate and pyroborate structural groups. A broader distribution of Al–O bond lengths in PDF also supports the enhanced network connectivity. Viscosity measurements show the increase in viscosity of molten slags with increasing mass ratio of BaO to CaO, which further attributes to the enhanced degree of polymerization of the aluminate network.     

Corrosion stability of polyester coatings on steel pretreated with different iron–phosphate coatings

The influence of steel surface pretreatment with different types of iron–phosphate coatings on the corrosion stability and adhesion characteristics of polyester coatings on steel was investigated. The phosphate coating was chemically deposited either from the simple novel plating bath, or with the addition of NaNO₂, as an accelerator in the plating bath. The morphology of phosphate coatings was investigated using atomic force microscopy (AFM). The corrosion stability of polyester coatings on steel pretreated by iron–phosphate coatings was investigated by electrochemical impedance spectroscopy (EIS) in 3% NaCl solution, while “dry” and “wet” adhesion were measured by a direct pull-off standardized procedure. It was shown that greater values of pore resistance, R_p, and smaller values of coating capacitance of polyester coating, C_c, on steel pretreated with iron–phosphate coating were obtained, as compared to polyester coating on steel phosphated with accelerator, and on the bare steel. The surface roughness of phosphate coating deposited on steel from the bath without accelerator is favorable in forming stronger bonds with polyester coating. Namely, the dry and wet adhesion measurements are in accordance with EIS measurements in 3% NaCl solution, i.e. lower adhesion values were obtained for polyester coating on steel phosphated with accelerator and on the bare steel, while the iron–phosphate pretreatment from the novel bath enhanced the adhesion of polyester coating on steel.     

Enhancement of oxidation resistance at 1000–1400 °C of low carbon Al2O3–C refractories with pre-synthesized SiCnw/Al2O3

The oxidation resistance of low carbon Al₂O₃–C refractories with the addition of SiC_nw/Al₂O₃ composite powders and the enhancement mechanisms were investigated. The oxidation resistance was evaluated by oxidation index (O.I.) and oxidation rate constant (k). The enhancement mechanisms of SiC_nw/Al₂O₃ on oxidation resistance were analyzed based on the phases and microstructures. The results showed that the SiC_nw/Al₂O₃ can improve the oxidation resistance of Al₂O₃–C refractories, the O.I. and k of A6 (6 wt% SiC_nw/Al₂O₃ addition) were 26.0% and 34.5% lower than those of reference sample A0, respectively. The oxidation resistance of refractories was improved in a range of 1000–1400 °C due to the introduction of SiC_nw/Al₂O₃. The enhancement mechanisms can be explained that SiC_nw is more susceptible to be oxidized due to its high specific surface area, which expanded the action temperature range of other antioxidants and itself. The mullite and dense protective layer generated during oxidation is also beneficial to impede the diffusion of O₂.     

Improved thermal shock stability and oxidation resistance of low-carbon MgO–C refractories with introduction of SiC whiskers

This research focuses on the utilization of SiC whiskers synthesized from rice husk powders in low-carbon magnesia–carbon (MgO–C) refractories, and attempts to reduce the flake graphite content in refractories by adding synthesized SiC whiskers. The effect of the addition amount of SiC whiskers on the microstructure, mechanical properties, thermal shock stability and oxidation resistance of MgO–C refractories with different graphite content was studied. The results indicated that the introduction of SiC whiskers facilitated the generation and growth of ceramic phases in MgO–C refractories. By adding 1 wt% SiC whiskers, the graphite content could be reasonably reduced (from 5 wt% to 4 wt%), and the strength, thermal shock stability and oxidation resistance of refractories were enhanced by the synergistic effect of the introduced SiC whiskers and the generated ceramic phases, the CMOR, CCS, residual CCS, and oxidation resistance were increased by 44, 6, 12 and 27% respectively.     

Improved thermal shock resistance of low-carbon Al2O3–C refractories fabricated with C/MgAl2O4 composite powders

The addition of C/MgAl₂O₄ composite powders can improve the thermal shock resistance of low-carbon Al₂O₃–C refractories attribute to the formation of microcracks in the agglomerated structure, thus consuming more thermal stress and strain energy. Moreover, C/MgAl₂O₄ composite powders additive promote the formation of short fibrous ceramic phases in the refractories, which suggest a bridging role in the interior of the refractories and increase its toughness. Furthermore, the C/MgAl₂O₄ composite powders also result in a remarkable enhancement of the slag corrosion resistance in the refractories.     

Comparative analysis on corrosion behavior of lightweight and dense mullite–corundum refractories: Role of Si-rich phase

The corrosion resistance of lightweight and dense mullite–corundum refractories to cement materials was examined. The specimens following static crucible treatment were investigated using phase analysis, microstructure, and thermodynamic simulation. The results reveal that diffusion of the silica-rich phase enhances alumina saturation solubility in the slag, reducing the corrosion resistance of the mullite–corundum refractories. The large proportion of closed pores and the continuous net-like structure of anorthite created by the corrosion reaction in the matrix, on the other hand, prevent further slag penetration into the lightweight mullite–corundum refractories. As a result, the presence of the silica-rich phase assures better slag penetration resistance of lightweight mullite–corundum refractories.     

Influence of Ti3AlC2 addition on water vapor resistance of low-carbon Al2O3–C refractories

Al₂O₃–C refractories are potential candidates for use in gasifiers, and they are Cr₂O₃-free. However, the oxidation of the carbon species and ceramic phases within the high-temperature water vapor environment may deteriorate the integrity of the working lining. Ti₃AlC₂ has been verified as an effective antioxidant for Al₂O₃–C refractories in air. In this study, the structural transformation of Ti₃AlC₂ during heat treatment and the water vapor resistance of Ti₃AlC₂-containing Al₂O₃–C refractories are investigated. The results show that the oxidation of Ti₃AlC₂ and Si in the matrix contributes to the in situ formation of a multilayer core–shell structure of TiC–AlTi₂O₅–Al₆Si₂O₁₃. These structural evolutions improve densification and stimulate pore size refinement, which enhances the mechanical properties and thermal stress resistance of the specimens. In particular, the refined pore size contributes to the significantly improved water vapor resistance at high temperatures.     

Oxidative dehydrogenation of ethanol over AgLi–Al2O3 catalysts containing different phases of alumina

Oxidative dehydrogenation of ethanol over the AgLi–Al₂O₃ catalysts having different phase compositions of alumina was investigated. The pure gamma (CHI00), pure chi (CHI100) and equally mixed phases (CHI50) derived from the solvothermal synthesis can play important roles on the physicochemical properties of AgLi–Al₂O₃ catalysts. Especially, the amount of weak basic sites, the oxidation state of Ag, and the reduction behaviors of catalysts are crucial in determining the ethanol conversion and product selectivity. It was found that increased amounts of weak basic sites and Ag_n^δ + clusters enhanced the catalytic activity as seen for the AgLi–CHI50 catalyst.     

Thermal shock resistance of magnesia–chrome refractories—experimental and criterial evaluation

Eleven commercially available magnesia–chrome refractories have been tested. Their basic properties have been determined along with bending strengths at 20,950 and 1400 °C, linear thermal expansion coefficients at 950 °C and 1400 °C, Young's modulus by the static method and the work of fracture at 950 °C. Young's modulus was determined within the temperature range 20–1000 °C, in the process of heating and cooling. The values of thermal shock resistance R_st and R₄ were calculated and correlated to thermal shock resistance (TSR). It has been demonstrated that the R_st criterion is a useful tool to forecast TSR, no matter whether the value of the E modulus is determined by the static or dynamic method. The values of Young's modulus obtained by various methods at 20 °C and 950 °C have been compared. It has been proven that Young's modulus dependence on temperature is a specific feature of a given material.     

Formation of hollow MgO-rich spinel whiskers in low carbon MgO–C refractories with Al additives

MgO–C refractories with different carbon contents have been developed to meet the requirement of steel-making technologies. Actually, the carbon content in the refractories will affect their microstructure. In the present work, the phase compositions and microstructure of low carbon MgO–C refractories (1 wt% graphite) were investigated in comparison with those of 10 wt% and 20 wt% graphite, respectively. The results showed that Al₄C₃ whiskers and MgAl₂O₄ particles formed for all the specimens fired at 1000 °C. With the temperature up to 1400 °C, more MgAl₂O₄ particles were detected in the matrix and AlN whiskers occurred locally for high carbon MgO–C specimens (10 wt% and 20 wt% graphite). However, the hollow MgO-rich spinel whiskers began to form locally at 1200 °C and grew dramatically at 1400 °C in low carbon MgO–C refractories, whose growth mechanism was dominated by the capillary transportation from liquid Al at these temperatures.     

Enhanced performance of low-carbon MgO–C refractories with nano-sized ZrO2–Al2O3 composite powder

Low-carbon MgO–C refractories are facing great challenges with severe thermal shock and slag corrosion in service. Here, a new approach, based on the incorporation of nano-sized ZrO₂–Al₂O₃ composite powder, is proposed to enhance the thermal shock resistance and slag resistance of such refractories in this work. The results showed that addition of ZrO₂–Al₂O₃ composite powder was helpful for improving their comprehensive performances. Particularly, the thermal shock resistance of the specimen containing 0.5 wt% composite powder was enhanced significantly which was related to the transformation toughening of zirconia and in-situ formation of more spinel phases in the matrix; also, the slag resistance of the corresponding specimen was significantly improved, which was attributed to the optimization of pore structure and formation of much thicker MgO dense layer.     

Corrosion study of hybrid sol–gel coatings containing boehmite nanoparticles loaded with cerium nitrate corrosion inhibitor

To improve the corrosion protection of sol–gel derived hybrid silica/epoxy coatings containing boehmite nanoparticles, inorganic corrosion inhibitor was introduced into the coating via encapsulation in the nanoparticles. The morphology and chemical structure of the deposited films were studied by Scanning Electron Microscopy (SEM) and Fourier Transformed Infra-red Spectroscopy (FT-IR). The anticorrosion and self-healing properties of the coatings were evaluated by Electrochemical Impedance Spectroscopy (EIS). The high corrosion resistance performance of such coatings is due to the presence of encapsulated cerium nitrate corrosion inhibitor that can be released at the defects within the coating, hindering the corrosion reactions at defective sites.     

Corrosion study of hybrid sol–gel coatings containing boehmite nanoparticles loaded with cerium nitrate corrosion inhibitor

To improve the corrosion protection of sol–gel derived hybrid silica/epoxy coatings containing boehmite nanoparticles, inorganic corrosion inhibitor was introduced into the coating via encapsulation in the nanoparticles. The morphology and chemical structure of the deposited films were studied by Scanning Electron Microscopy (SEM) and Fourier Transformed Infra-red Spectroscopy (FT-IR). The anticorrosion and self-healing properties of the coatings were evaluated by Electrochemical Impedance Spectroscopy (EIS). The high corrosion resistance performance of such coatings is due to the presence of encapsulated cerium nitrate corrosion inhibitor that can be released at the defects within the coating, hindering the corrosion reactions at defective sites.