Calcium aluminate cement source evaluation for Al2O3-MgO refractory castables

Alumina-magnesia refractory castables are commonly bonded with calcium aluminate cements. At temperatures above 1200 °C, these materials present an expansive behavior due to the in situ spinel (MgAl₂O₄) formation and the CA₂ and CA₆ ones. One alternative to control the volumetric stability is by replacing the typical cements used (30 wt.% CaO) for another containing less lime (20 wt.% CaO). Nevertheless, when changing the cement sources, the castable's properties would be affected. Among them, the most relevant are the green mechanical strength, the drying behavior, the properties at intermediate and high temperatures, the expansion behavior, the hot modulus of rupture and creep. Considering these aspects, the objective of this work was to evaluate the impact of different cement sources in the processing steps and properties of alumina-magnesia castables. The results pointed out specific behaviors for each cement source during the whole processing stages, highlighting the importance of its proper selection in order to attain the required properties in working conditions.     

Effect of Al2O3 on mechanical properties of Ti3SiC2/Al2O3 composite

The effect of Al₂O₃ on mechanical properties of Ti₃SiC₂/Al₂O₃ composite fabricated by SPS was studied systematically. The results show that the hardness of the Ti₃SiC₂/Al₂O₃ composite can reach 10.28 GPa, 50% higher than that of pure Ti₃SiC₂. However, slight decrease in the other mechanical properties was observed with Al₂O₃ addition higher than 5–10 vol.%, which is believed to be due to the agglomeration of Al₂O₃ in the composite.     

Effect of surface-modified Al2O3 on the thermomechanical properties of polybutylene succinate/Al2O3 composites

This study investigates the effect of the incorporation of alumina particles on the thermomechanical properties of polybutylene succinate (PBS)/Al₂O₃ composites. The alumina surface was modified with the carboxylic groups of maleic acid through simple acid-base and in situ polymerization reactions. Scanning electron microscope (SEM) results revealed the introduction of maleic acid treated alumina significantly affect the morphology of the PBS/Al₂O₃ composites as compared to the neat PBS. The thermal conductivity of the composite (0.411?W?m^?1 K^?1) was more than twice that of neat PBS. The composite containing polymerization-modified alumina showed a 50% increase in storage modulus compared with that of neat PBS. In addition, universal testing machine (UTM) and differential scanning calorimetry (DSC) measurements indicated an increase in the tensile strength and degree of crystallinity after the incorporation of modified alumina in the PBS/Al₂O₃ composite.     

Changes in the microstructure and mechanical properties of Al2O3/YSZ directionally solidified eutectic ceramics during long-time heat treatment

Al₂O₃/YSZ directionally solidified eutectic ceramics (DSECs) were prepared using the induction heating zone melting (IHZM) method. The microstructures of the DSECs formed with various crucible pulling rates (2.5–300 mm/h) changed from the discontinuous lamellar into the colony structure, finally into the cell structure. The intracolony had better microstructural stability than the intercolony during heat treatment due to two factors: the size effect and the t-m transformation effect. The hardness changes were mainly related to the release and generation of residual stress caused by repeated heating and cooling. The quantity of cracks in DSECs increased with the heat treatment time, leading to a gradual decrease in the fracture toughness, 300 mm/h DSEC had the lowest reduction in fracture toughness after 500 h heat treatment due to fine microstructure, the fracture toughness was 7.15 MPa·m^1/2, which was 76 % of that before the heat treatment (9.39 MPa·m^1/2).     

Microstructure and mechanical properties of gas pressure sintered Al2O3/TiCN composite

Al₂O₃–30 wt.%TiCN composites have been fabricated successfully by a two-stage gas pressure sintering schedule. The gas pressure sintered Al₂O₃–30 wt.%TiCN composite achieved a relative density of 99.5%, a bending strength of 772 MPa, a hardness of 19.6 GPa, and a fracture toughness of 5.82 MPa m^1/2. The fabrication procedure involves solid state sintering of two phases without solubility to prepare Al₂O₃–TiCN composite. Little grain growth occurred for TiCN during sintering while Al₂O₃ grains grew about three times to an average size of 3–5 μm. The interface microstress arising during cooling from the processing temperature because of the thermal and/or mechanical properties mismatch between the Al₂O₃ and TiCN phase is about 50 MPa. Such a compressive microstress is not high enough to cause grain boundary cracking that may weaken the composite but it can introduce dislocations within grains, which is very good to enhance the composite properties.     

Influences of novel Si2BC3N antioxidant on the structure and properties of Al2O3-SiC-C castables: In air and coke bedded atmosphere

The ultra-low cement bonded Al₂O₃-SiC-C castables were prepared with the introduction of a novel Si₂BC₃N antioxidant. The microstructure evolution and the mechanical properties were evaluated in coke bed and air atmosphere. Besides, the thermal properties, including thermal shock, hot modulus of rupture, oxidation and refractories under load, were comparatively investigated. The results show that the Si₂BC₃N powder together with B₄C and Si can satisfy the oxidation resistance requirements over a full temperature range. Si₂BC₃N has mainly two effects depending on the treating temperature: 1) it protects the carbon from oxidation and increases the structure integrity when the specimens are treated below 1100?°C; 2) it stimulates the growth of SiC whiskers under 1400?°C due to the enhanced reaction between SiO and CO. Consequently, the CMOR and CCS of the Si₂BC₃N containing specimens have been improved attributing to the structural integrity and more SiC whiskers formation, regardless of the treating atmosphere. Besides, the thermal properties such as the hot modulus of rupture, thermal shock and refractories under load are also optimized with Si₂BC₃N addition.     

Effect of microstructure and mechanical properties on wear behavior of plasma-sprayed Cr2O3-YSZ-SiC coatings

In this study, the microstructure and mechanical properties of the atmospheric plasma-sprayed Cr₂O₃ (C), Cr₂O₃-20YSZ (CZ), and Cr₂O₃-20YSZ-10SiC (CZS) coatings were evaluated and also compared with each other, so as to explain the coatings wear behavior. Microstructural evaluations included X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) equipped with energy dispersive X-ray spectroscopy (EDX) and porosity measurements. Mechanical tests including bonding strength, fracture toughness, and micro-hardness tests were used to advance our understanding of the correlation between the coatings properties and their wear behavior. The sliding wear test was conducted using a ball-on-disk configuration against an alumina counterpart at room temperature. Addition of multimodal YSZ and subsequent SiC reinforcements to the Cr₂O₃ matrix resulted in an increase in the fracture toughness and Vickers micro-hardness, respectively. It was found that the composite coatings had comparable coefficients of friction with pure Cr₂O₃ coatings. When compared with the C coating, the CZ and CZS composite coatings with higher fracture toughness exhibited superior wear resistance. Observation of the wear tracks of the coatings indicated that the lower wear rates of the CZ and CZS coatings were due to the higher plastic deformation of the detached materials. In fact, improvement in the wear resistance of the composite coatings was attributed to a phase transformation toughening mechanism associated with tetragonal zirconia which created more ductile tribofilms during the wear test participated in filling the pores of coatings.     

Effect of sodium polyacrylate on mechanical properties and microstructure of metakaolin-based geopolymer with different SiO2/Al2O3 ratio

The mechanical properties and microstructure of geopolymer are affected by the molar ratio of SiO₂/Al₂O₃. Meanwhile, organic polymer has the effect of improving the toughness of geopolymer, which depends on the SiO₂/Al₂O₃ ratio of geopolymer inevitably. Therefore, it is important to investigate the effect of the organic polymer on the mechanical properties and microstructure of geopolymer with varying SiO₂/Al₂O₃ ratio for using organic polymer to modify geopolymer. In this work, the SiO₂/Al₂O₃ ratios of metakaolin-based geopolymers are adjusted to 2.0, 2.5, 3.0, 3.5 and 4.0 by adding silica fume and β-Al₂O₃, with Na₂O/SiO₂, H₂O/SiO₂ being maintained at 0.2, 4.0, respectively. The geopolymers with each SiO₂/Al₂O₃ ratios are modified by addition of 0, 0.4, 0.8, 1.2 and 1.6?wt% of sodium polyacrylate (PAAS).The mechanical properties of these samples are measured and the rate of change is used to characterize the effect of PAAS on the metakalin-based geopolymers. The mechanism is also shown by 29Si NMR, XPS and FTIR. The results show that the effects of polymer on the mechanical properties of metakaolin-based geopolymer are affected by SiO₂/Al₂O₃ ratio and the effect becomes less obvious with SiO₂/Al₂O₃ ratio increasing from 2.0 to 4.0. Incorporation of PAAS can reduce the degree of polymerization of [SiO]₄ or [AlO]₄ in geopolymer and form the Si?O?C bond, which are two main reasons for polymer improving the toughness of geopolymer. But these effects decrease when the SiO₂/Al₂O₃ ratio of geopolymer increases from 2.0 to 4.0, which is corresponding to the effect on the mechanical properties. The toughening effect of organic polymer on geopolymer depends on the SiO₂/Al₂O₃ ratio of geopolymer, and only the geopolymer with lower SiO₂/Al₂O₃ ratio (no more than 2.5 in this work) can be significantly toughening modified by organic polymer. Therefore, it is necessary to consider the SiO₂/Al₂O₃ ratio of the geopolymer when geopolymer modified by organic polymer is designed.     

Effects of heat treatment on mechanical properties of 3D Si3N4f/BN/Si3N4 composites by PIP

The fabrication of three-dimensional silicon nitride (Si₃N₄) fiber-reinforced silicon nitride matrix (3D Si₃N_4f/BN/Si₃N₄) composites with a boron nitride (BN) interphase through precursor infiltration and pyrolysis (PIP) process was reported. Heat treatment at 1000–1200 °C was used to analyze the thermal stability of the Si₃N_4f/BN/Si₃N₄ composites. It was found after heat treatment the flexural strength and fracture toughness change with a pattern that decrease first and then increase, which are 191 ± 13 MPa and 5.8 ± 0.5 MPa·m^1/2 respectively for as-fabricated composites, and reach the minimum values of 138 ± 6 MPa and 3.9 ± 0.4 MPa·m^1/2 respectively for composites annealed at 1100 °C. The influence mechanisms of the heat treatment on the Si₃N_4f/BN/Si₃N₄ composites include: (Ⅰ) matrix shrinkage by further ceramization that causes defects such as pores and cracks in composites, and (Ⅱ) prestress relaxation, thermal residual stress (TRS) redistribution and a better wetting at the fiber/matrix (F/M) surface that increase the interfacial bonding strength (IBS). Thus, heat treatment affects the mechanical properties of composites by changing the properties of the matrix and IBS, where the load transfer efficiency onto the fibers is fluctuating by the microstructural evolution of matrix and gradually increasing IBS.     

Effect of the sulfidation process on the mechanical properties of a CoMoP/Al2O3 hydrotreating catalyst

Mathematical models for the mechanical properties of a CoMoP/Al₂O₃ hydrotreating catalyst in the sulfidation process are developed with response surface methodology. A Doehlert design is performed to collectively study the effects of sulfidation temperature, time and heating rate on the mean strength, Weibull modulus and pellet density. Analysis of variance reveals that the models developed for the mean strength and Weibull modulus are adequate. The validity of the models is also verified by experimental data. Analyses of response surfaces show that in the great part of the experimental domain examined, as the sulfidation temperature increases the mean strength decreases, while the Weibull modulus increases at first and then decreases. The middle level of the sulfidation time results in smaller mean strength and higher Weibull modulus. The Weibull modulus decreases with increasing heating rate; however, the effect of the heating rate on the mean strength is statistically less pronounced. It is concluded that there is a great potential for improving the catalyst mechanical reliability in the sulfidation process, while the pellet density does not vary significantly.     

Effects of the calcination conditions on the mechanical properties of a PCoMo/Al2O3 hydrotreating catalyst

Mathematical models for the effects of the calcination process conditions on the mechanical properties of a PCoMo/Al₂O₃ hydrotreating catalyst are developed using a response surface methodology. A central composite design is performed to study collectively the effects of calcination temperature, calcination time and heating rate on the mean strength and Weibull's modulus. A model is obtained for each response with multiple regression analysis and then is refined. Analysis of variance reveals that the models developed are adequate. The validity of the models is also verified by experimental data. Statistics reveals that there is a great potential for increasing the mechanical reliability in the calcination process. Analysis of response surface show that the mean strength and Weibull's modulus increase with the increase of calcination temperature. The middle level of heating rate results in smaller mean strength and higher Weibull's modulus. The mean strength increases as calcination time increases. However, calcination time has no significant effect on Weibull's modulus in the experimental domain examined.     

Cr2O3 nanoparticles: A promising candidate to improve the mechanical properties and corrosion resistance of Ni-Co alloy coatings

This study was aimed to assess the effects of reinforcement nanoparticles content, on the microstructural features, mechanical properties, and corrosion-related properties of Ni-Co-Cr₂O₃ nanocomposite coatings. Scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), and X-ray diffraction (XRD) analysis were employed in order to evaluate the microstructural features and chemical composition of the nanocomposites. Moreover, the microhardness tester and electrochemical impedance spectra (EIS) tests coupled with potentiodynamic polarization measurements were used to investigate the mechanical and corrosion-related properties, respectively. Results demonstrate that albeit the volume fraction of cobalt in coating, average particle size, Cr₂O₃ nanoparticle content in coating, and microstructural features are of prime significance in determining the mentioned properties of the nanocomposite coatings, Co content is more important. Actually, Cr₂O₃ nanoparticles serve as suitable nucleation sites for Co particles deposition throughout the microstructure. Thus, combined actions of Cr₂O₃ nanoparticles incorporation and their optimal content ensures the nucleation of high population of Co particles, which significantly contributes to the improvement in the properties. The Ni-Co-8.9 wt%Cr₂O₃ nanocomposite coating exhibits the superior mechanical and corrosion-related properties.     

Al2O3/Cu-O composites fabricated by pressureless infiltration of paper-derived Al2O3 porous preforms

Al₂O₃/Cu-O composites were fabricated from the paper-derived alumina matrix infiltrated with a Cu-3.2?wt% O alloy. Paper-derived alumina preforms with an open porosity ranging from ～ 14 to ～ 25?vol% were prepared by sintering of alumina-loaded preceramic papers at 1600?°C for 4?h. Pressureless infiltration at 1320?°C for 4?h of the preforms with Cu–O alloy resulted in the nearly dense materials with good mechanical and electrical properties, e.g. fracture toughness up to 6?MPa?m^0.5, four-point-bending strength up to 342?MPa, Young's modulus up to 281?GPa and electrical conductivity up to 2?MS/m depending on the volume fraction of copper alloy in the composites. The technological capability of this approach was demonstrated using prototypes in various engineering fields fabricated by lamination, corrugating and Laminated Object Manufacturing (LOM) methods.     

Enhanced mechanical properties of 3 Y2O3 stabilized tetragonal ZrO2 incorporating tourmaline particles

The current study reports on the improvement of mechanical properties of 3?mol% Y₂O₃ stabilized tetragonal ZrO₂ (3Y-TZP) by introduction of tourmaline through ball milling and subsequent densification by pressureless sintering at 800, 1200, 1300, 1400?°C. Findings demonstrate that no matter which sintering temperature the 3Y-TZP ceramic containing 2?wt% tourmaline reach a maximum value in flexural strength and fracture toughness as compared to other composite ceramics. As the tourmaline content is 2?wt% and the sintering temperature is 1300?°C, the flexural strength and fracture toughness of the composite ceramics are the highest, increases of 36.2% and 36.6% over plain 3Y-TZP ceramic respectively. The unique microstructure was systematically investigated through X-ray diffraction, scanning electron microscopy, energy dispersive spectrum, and flourier transform-infrared. The strengthening and toughening mechanism of tourmaline in 3Y-TZP ceramic were also discussed.     

Infiltration of Al2O3/Y2O3 mix into SiC ceramic preforms

Silicon carbide ceramics are very interesting materials to engineering applications because of their properties. These ceramics are produced by liquid phase sintering (LPS), where elevated temperature and time are necessary, and generally form volatile products that promote defects and damage their mechanical properties. In this work was studied the infiltration process to produce SiC ceramics, using shorter time and temperature than LPS, thereby reducing the undesirable chemical reactions. SiC powder was pressed at 300 MPa and pre-sintered at 1550 °C for 30 min. Unidirectional and spontaneous infiltration of this preform by Al₂O₃/Y₂O₃ liquid was done at 1850 °C for 5, 10, 30 and 60 min. The kinetics of infiltration was studied, and the infiltration equilibrium happened when the liquid infiltrated 12 mm into perform. The microstructures show grains of the SiC surrounded by infiltrated additives. The hardness and fracture toughness are similar to conventional SiC ceramics obtained by LPS.     

Kinetics of geopolymerization: Role of Al2O3 and SiO2

The early-stage reaction kinetics of metakaolin/sodium silicate/sodium hydroxide geopolymer system have been investigated. The setting and early strength development characteristics, and associated mineral and microstructural phase development of mixtures containing varying SiO₂/Al₂O₃ ratios, cured at 40 °C for up to 72 h, were carefully studied. It was observed that setting time of the geopolymer systems was mainly controlled by the alumina content. Essentially, the setting time increased with increasing SiO₂/Al₂O₃ ratio of the initial mixture. Up to a certain limit, the SiO₂/Al₂O₃ ratio was also found to be responsible for observed high-strength gains at later stages. An increase in the Al₂O₃ content, i.e. for low SiO₂/Al₂O₃ ratio, led to products of low strength, accompanied by microstructures with increased amounts of Na-Al-Si-containing “massive” phases (grains). EDAX analyses showed that the SiO₂/Al₂O₃ ratios of geopolymer gel phases were quite similar to those of the starting mixtures, but with an overall lower Na content. Most importantly, this study clearly demonstrates that the properties of resulting geopolymer systems can be drastically affected by minor changes in the available Si and Al concentrations during synthesis.     

Improved mechanical and wear properties of hybrid Al-Al2O3/GNPs electro-less coated Ni nanocomposite

Al was successfully reinforced with two ceramics Al₂O₃ coated Ni and graphene nanoplatelets (GNPs) coated Ni by electro-less deposition technique to form Al-Al₂O₃/$\mathit{x}$ GNPs hybrid nanocomposite ($\mathit{x}=0,0.2,0.6,1$and $1.4\%$) with improved mechanical and wear properties. Compressive strength, hardness, wear properties and coefficient of friction were investigated. The results indicated that increasing GNPs volume fraction improves compressive strength, hardness and antifriction properties of composites significantly. In comparison with pure aluminum, 1.52- fold increases in the strength, 2.45-fold increase in the hardness and 19.2-fold decreases in the wear rate of Al-10%Al₂O₃/1.4%GNPs nanocomposite are achieved. This improvement is attributed to the remarkable mechanical strength and excellent self-lubrication of grapheme, the reduction of grain size during electro-less deposition process and the increased efficient stress transfer due to the curled structure of GNPs. Additionally, coating GNPs with Ni particles prevent the formation of Al₃C₄ intermetallic phase which lead to this large improvement in the wear rate. In comparison with the available results in the literature, electro-less coating of GNPs with Ni provides 2.1 times larger hardness than composite with uncoated GNPs.     

Sintering behavior and mechanical properties of nano-sized Cr3C2/Al2O3 composites prepared by MOCVI process

A process using metal-organic chemical vapor infiltration (MOCVI) conducted in fluidized bed was employed for the preparation of nano-sized ceramic composites. The Cr-species was infiltrated into Al₂O₃ granules by the pyrolysis of chromium carbonyl (Cr(CO)₆) at 300–450 °C. The granulated powder was pressureless sintered or hot-pressed to achieve high density. The results showed that the dominant factors influencing the Cr-carbide phases formation, either Cr₃C₂ or Cr₇C₃, in the composite powders during the sintering process were the temperature and oxygen partial pressure in the furnace. The coated Cr-phase either in agglomerated or dispersive condition was controlled by the use of colloidal dispersion. The microstructures showed that fine (20 –600 nm) Cr_xC_y grains (≤8 vol.%) located at Al₂O₃ grain boundaries hardly retarded the densification of Al₂O₃ matrix in sintering process. The tests on hardness, strength and toughness appeared that the composites with the inclusions (Cr₃C₂) had gained the advantages over those by the rule of mixture. Even 8 vol.% ultrafine inclusions have greatly improved the mechanical properties. The strengthening and toughening mechanisms of the composites were due to grain-size reduction, homogenous dispersion of hard inclusions, and crack deflection.     

Effect of Fe2O3 doping on colour and mechanical properties of Y-TZP ceramics

Yttria-stabilized zirconia (Y-TZP) samples with different Fe concentrations were prepared aiming to study the effects of Fe₂O₃ doping on colour and mechanical properties. Since colour is an important optical property for jewellery and watchmaking, the investigation of colour in zirconia ceramics has a great scientific and technological interest. An investigation of the mechanical and optical properties, specifically the colour, was developed starting from commercial partially yttria-stabilized zirconia (Y-TZP) powders produced by Emulsion Detonation Synthesis (EDS). Within the strategies to get colours, the use of colouring oxides such as iron oxide (Fe₂O₃) was the chosen approach. The addition of specific ions into the ZrO₂ matrix can be used to tune zirconia colour without compromising its outstanding mechanical properties. Doping with iron oxide has proved to be a suitable, reproducible and irreversible colouring mechanism, allowing the development of a chromatically beige stable material with respect to its use in different processing conditions such as different atmospheres and temperature ranges. XRD results suggested that iron ions dissolved into tetragonal zirconia phase are at interstitial positions since the unit-cell volume of the tetragonal zirconia increases with increasing iron content. The effect of dopant addition on the mechanical properties of Y-TZP ceramics was also assessed. Compared to the undoped samples, doped ones exhibit a similar Vickers hardness (>1200?MPa) and biaxial flexural strength (>1000?MPa). However, it was observed that Fe₂O₃ doping slightly decreased the fracture toughness of Y-TZP ceramics.     

Synthesis and mechanical properties characterization of multiferroic BiFeO3-CoFe2O4 composite nanofibers

Multiferroic nanofibers with excellent mechanical properties have great potential applications in multifunctional nanodevices. BiFeO₃-CoFe₂O₄ (BFO-CFO) composite nanofibers with different molar ratios were successfully synthesized by sol-gel-based electrospinning method. The mechanical properties of BFO-CFO composite nanofibers were examined by nanoindentation technique, and further investigated by amplitude modulation-frequency modulation (AM-FM) method based on atomic force microscopy (AFM). The results of AM-FM showed that the elastic moduli of BFO-CFO composite nanofibers increased with the increase of CFO ratio, which was consistent with the results of nanoindentation. These results indicated that AFM-based AM-FM is a powerful method for nondestructively investigating the mechanical properties of materials at nanoscale, and that the results of BFO-CFO composite nanofibers are also of practical importance for the future applications of multifunctional nanodevices.