TiAl/B4C marine material—Fabrication, mechanical and corrosion properties

A novel TiAl/B₄C intermetallic/ceramic matrix composite was fabricated by high energy ball milling followed by hot press sintering. The microstructure of TiAl/B₄C composite was studied and its mechanical properties and corrosion resistance behaviors were investigated. The bending strength and fracture toughness of the composite reached 437.3 MPa and 4.85 MPa m^1/2, respectively, i.e., much higher values than the monolithic phase B₄C. The potentiodynamic polarization measurements and electrochemical impedance spectroscopy results indicated the excellent corrosion resistance of such composite material.     

Corrosion resistance properties of electroless nickel composite coatings

Electroless nickel (EN) composite coatings incorporated with PTFE and/or SiC particles demonstrated significantly improved mechanical and tribological properties as well as low surface energy which are desired for anti-sticking and wear resistant applications. The corrosion resistance of these composite coatings, however, has not been systematically studied and compared. This work aimed to investigate the corrosion characteristics of EN composite coatings using electrochemical measurements which include open circuit potential (OCP), electrochemical impedance spectroscopy and potentiodynamic test. The effects of the co-deposited particles on corrosion behavior of the coatings in 1.0 N H₂SO₄ and 3% NaCl media were investigated. The surface autocatalytic properties and the post-heat-treatment on coating corrosion resistance were also discussed. The results showed that both EN and EN composite coatings demonstrated significant improvement of corrosion resistance in both acidic and salty atmosphere. Ni striking substantially enhanced the corrosion resistance due to the improvement of the surface autocatalytic properties and homogeneity. Proper post-heat-treatment significantly improves the coating density and structure, giving rise to enhanced corrosion resistance.     

Ni–W coatings electrodeposited on carbon steel: Chemical composition, mechanical properties and corrosion resistance

Hard, ductile and adherent nanostructured Ni–W coatings were electrodeposited on carbon steel from electrolyte solutions containing sodium tungstate, nickel sulfate and sodium citrate, using different current pulse programs. Current pulse frequency was the dominant factor to define chemical composition, grain size, thickness and hardness. According to the electrodeposition conditions the deposited coatings showed 15–30 at% W, the grain size ranged from 65 to 140 nm, and the hardness varied from 650 to 850 Hv. Tungsten carbide also present in the coating contributed to its hardness. The corrosion resistance of the Ni–W coated steel was tested by potentiodynamic polarization in a neutral medium containing sulphate ions. The Ni–W coating protected the carbon steel from localized corrosion induced by sulphate anions.     

Electrodeposited Ni-B alloy coatings: Structure, corrosion resistance and mechanical properties

Ni-B alloy coatings with different boron content ranging from 4 to approximately 28 at.% were prepared by electrodeposition in a nickel-plating bath containing sodium decahydroclovodecaborate as a boron source. The influence of the boron concentration in the coatings on their structure, morphology, electrochemical and corrosion behavior, physico-mechanical and electrical properties was investigated using X-ray diffractometry (XRD), scanning electron microscopy (SEM), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and other methods. It was found that the electrodeposited Ni-B coatings with relatively low boron content (≤8 at.%) are nanocrystalline and comprise a solid solution of boron in f.c.c. Ni lattice having a mixed substituted-interstitial type. Further increase in the boron content (up to 10-15 at.%) leads to the appearance of heterogeneous amorphous-nanocrystalline structure, and the coatings with a high boron content (20 at.% and above) are X-ray amorphous. Polarization measurements in neutral NaCl solutions showed that the Ni-B coatings with relatively low boron content demonstrate a potential region of low anodic currents associated with the passive film formation at the alloy surface. The anodic current in this potential region increases significantly with increasing the boron content above 10 at.%, suggesting the non-protective nature of the anodic film formed on the amorphous Ni-B alloys. Immersion tests monitored by EIS measurements revealed a significantly better corrosion performance of the Ni-B coatings with low boron content (4 at.%) in comparison with that of the amorphous coatings. The microhardness and wear resistance of the Ni-B coatings essentially increases with increasing the boron content. Maximum microhardness and wear resistance were found for the coatings containing 8 at.% B.     

High corrosion resistance of electroless composite plating coatings on AZ91D magnesium alloys

The process of electroless plating Ni-P on AZ91D magnesium alloys was improved. The Ni-P-ZrO₂ composite coatings and multilayer coatings were investigated based on the new electroless plating process. The coatings surface and cross-section morphologies were observed with scanning electron microscopy (SEM). The chemical compositions were analyzed by EDXS. The corrosion behaviors were evaluated by immersion, salt spray and electrochemical tests. The experimental results indicated that the Ni-P-ZrO₂ composite coatings suffered attack in NaCl solution but displayed passivation characteristics in NaOH and Na₂SO₄ solutions. The corrosion resistance of Ni-P-ZrO₂ coatings was superior to Ni-P coatings due to the effect of ZrO₂ nano-particle. The multilayer coatings consisting of Ni-P-ZrO₂/electroplating nickel/Ni-P (from substrate to surface) can protect magnesium alloys from corroding more than 1000 h for the salt spray test.     

Composite Ni/Al2O3 coatings and their corrosion resistance

Composite coatings Ni/Al₂O₃ were electrochemically deposited from a Watts bath. Al₂O₃ powder with particle diameter below 1 μm was codeposited with the metal. The obtained Ni/Al₂O₃ coatings contained 5-6% by weight of corundum. The structure of the coatings was examined by scanning electron microscopy (SEM). It has been found that the codeposition of Al₂O₃ particles with nickel disturbs the nickel coating's regular surface structure, increasing its microcrystallinity and surface roughness. DC and AC electrochemical tests were carried out on such coatings in a 0.5 M solution of Na₂SO₄ in order to evaluate their corrosion resistance. The potentiodynamic tests showed that the corrosion resistance of composite coating Ni/Al₂O₃ is better than that of the standard nickel coating. After 14 days of exposure the nickel coating corrodes three times faster than the Ni/Al₂O₃ coating. The electrochemical behaviour of the coatings in the corrosive solution was investigated by electrochemical impedance spectroscopy (EIS). An equivalent circuit diagram consisting of two RC electric circuits: one for electrode, nickel corrosion processes and the other for processes causing coating surface blockage, were adopted for the analysis of the impedance spectra. The changes in the charge transfer resistance determined from the impedance measurements are comparable with the changes in corrosion resistance determined from potentiodynamic measurements.     

Preparation and corrosion resistance of nonstoichiometric lanthanum zirconate coatings

Lanthanum zirconate is a promising thermal barrier coating material owing to its excellent thermophysical properties and La plays the key role in its corrosion resistance. Here, an amorphous precursor is used as raw feedstock material so as to synthesize lanthanum zirconate coatings with tailorable composition by atmospheric plasma spray (APS). Three lanthanum zirconate coatings of La_1.7Zr_2.3O_7.15, La_2.0Zr_2.0O_7.0 and La_2.3Zr_1.7O_6.85 are fabricated. Furthermore, the corrosion resistance of the as-sprayed coatings against CaO-MgO-Al₂O₃-SiO₂ at 1250℃ is investigated. The increased La content promotes the formation of a sealing layer of the crystalline Ca₂La₈(SiO₄)₆O₂ apatite, which slows down the penetration of molten CaO-MgO-Al₂O₃-SiO₂. Therefore, the infiltration rate of the La_2.3Zr_1.7O_6.85 coating decreased up to 42.6 % compared with the other two coatings. This work develops a feasible preparation strategy to control the La composition for the improved corrosion resistance, which is expected to guide the future coating design and synthesis for the materials with big composition changes during the APS process.     

Fabrication of hydrophobic surface with hierarchical structure on Mg alloy and its corrosion resistance

A hydrotalcite/hydromagnesite conversion coating with hierarchical structure has been fabricated on a Mg alloy substrate by in situ hydrothermal crystallization method. A MgO layer existing between the hydrotalcite/hydromagnesite film and the substrate was formed prior to the hydrotalcite/hydromagnesite film during the crystallization process. After surface treatment with silane coupling agent, the surface of conversion coating changes from hydrophilic to hydrophobic. Scanning electron microscopy (SEM) revealed that the silylated conversion coating with hierarchical structure maintains the original rough surface of which was composed of numerous micro-scale flakes and beautiful flower-like protrusions. Polarization measurements have shown that the hydrophobic conversion coating exhibited a low corrosion current density value of 0.432 μA/cm², which means that the hydrophobic conversion coating can effectively protect Mg alloy from corrosion. Electrochemical impedance spectroscopy (EIS) showed that the impedance of the hydrophobic conversion coating was 9000 Ω. It means that the coating served as a passive layer with high charge transfer resistance.     

The effect of the PVC/CPVC ratio on the corrosion resistance properties of organic coatings

The effect of the ratio of the pigment volume concentration (PVC) to the critical pigment volume concentration (CPVC), denoted hereafter by Λ, on the corrosion resistance properties of paint films has been investigated by a.c. impedance and potential-time measurements. Painted mild steel electrodes were studied during exposure to 3% NaCl solution for up to 90 days. Paints based on alkyd, epoxy and chlorinated rubber/chlorinated paraffin (CR/CP) were prepared containing zinc phosphate as inhibitive pigment. The paints were prepared at Λ values 0.48, 0.51, 0.55, 0.58, 0.61, 0.64 and 0.67. It is concluded that, for all systems, corrosion resistance can be affected greatly by the PVC/CPVC ratio and each system has its own optimum Λ value. The optimum percentage of inhibitive pigment in the above systems has also been evaluated.     

Modification of Cr/CrN composite structure by Fe addition and its effect on decorative performance and corrosion resistance

A CrN ceramic coating is a promising substitution for electroplated Cr (Ⅵ) hard coatings; however, it has not yet replaced a decorative Cr (Ⅵ) layer owing to its low reflectivity of visible light and relatively poor corrosion resistance. A Cr/CrN composite structure can address these shortcomings. Our recent work demonstrated that an addition of Fe can facilitate the densification of hot-pressed Cr sputtering targets and enhance the mechanical properties of Cr/CrN composite coatings. In this work, we focus on reporting optical properties and corrosion resistance of the Fe-modified Cr/CrN layers for decorative applications, and clarifying the effect of Fe on these performances. The results show that Fe can increase the amount of metallic phase in the Cr/CrN composite structure and helps enhance its reflectance in the visible region. The composite coating deposited by Cr₉₀Fe₁₀ (at.%) target/alloy exhibits a greater reflectivity of visible light and a better corrosion resistance than those of a single-phase CrN coating. This is attributed to its fine microstructure, which is beneficial for a dense and smooth surface. The color of the coating can be controlled by both the partial pressure ratio of N₂ during deposition and the Fe content in the Cr-Fe sputtering target. The present results show that the addition of Fe can lead to the reduction in the processing cost of Cr targets, enhance the mechanical properties of the composite coatings, and broaden the deposition window. Such cost-effective Fe-modified Cr/CrN composite coatings are expected to be used in various decorative applications.     

H2SO4 as a passivating medium on the localised corrosion resistance of surgical 316L SS metallic implant and its effect on hydroxyapatite coatings

The localised corrosion resistance of 316L SS metallic implant due to H₂SO₄ treatment is being studied through electrochemical studies involving cyclic polarisation experiments and impedance studies. The efficiency of hydroxyapatite (HAP) coatings on H₂SO₄ treated 316L SS is also been investigated through electrochemical studies and the dissolution characteristics of the coatings. The study reveal that 15% H₂SO₄ treatment was found to be efficient in the corrosion resistance of 316L SS and dissolution of alloy is considerably reduced in the hydroxyapatite coatings on 15% H₂SO₄ treated 316L SS.     

The influence of pulse plating parameters on microstructure and properties of Ni-W-Si3N4 nanocomposite coatings

Nanosized silicon nitride (Si₃N₄) particles reinforced Nickel-tungsten composite coatings were deposited on the surface of C45 steel sheet by pulse electrodeposition. The effect of duty cycle, frequency, current pattern and presence of Si₃N₄ nanoparticles on microstructure, phases and corrosion resistance and mechanical properties of the coatings were investigated. The Si₃N₄ phase was incorporated into Ni-W alloy matrix uniformly and the inclusion content of in the coating was analyzed by energy dispersive x-ray spectrometer (EDS). The structure, microhardness and surface roughness of the coatings was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), Vickers micro-indenter and atomic force microscopy (AFM). The corrosion protection of steel by the coatings was evaluated by weight loss and electrochemical impedance spectroscopy (EIS). Corrosion rates of the coatings were determined using the Tafel polarization test. The results indicated that the duty cycle of 60%, pulse frequency of 1000 Hz, average current density of 5 A/dm⁻², and Si₃N₄ nanoparticles concentration of 30 g/L were the optimal plating conditions. The amount of Si₃N₄ particles incorporated into the coating that were produced under the optimum plating conditions was 2.1 wt%, and the microhardness was 1031 Hv as well as the crystallite size of this coating was 27 nm.     

Tensile strength and corrosion resistance properties of porous Al2O3/Ni composites prepared with rice husk pore-forming agent

The mechanical performance and chemical stability of porous alumina materials operating under harsh service conditions are of utmost importance in understanding their operational behavior if they are to stand the test of time. In the present study, the joint effect of nickel (Ni) reinforcement and rice husk (RH) pore-forming agent (PFA) on the tensile strength and the corrosion resistance properties of composite porous alumina ceramics was studied. To exploit the potential of this new porous alumina system, plain and Ni-reinforced porous alumina samples (Al₂O₃-xNi-RH; x?=?2, 4, 6 and 8?wt%) were developed through the powder metallurgy technique. Comprehensive investigation on the tensile strength properties of the developed porous alumina ceramics showed that relative to the plain sample (tensile strength and elastic modulus; 6.1?MPa and 1201?MPa), the presence of highly stable Ni₃Al₂SiO₈ spinelloid promoted the tensile strength enhancement (12.6–6.4?MPa) and the elastic modulus decline (897–627?MPa) of the composite samples. Similarly, corrosion resistance test was performed on the composite porous alumina samples in both 10?wt% NaOH and 20?wt% H₂SO₄ hot aqueous solutions. Overall, the composite samples demonstrated superior chemical stability in NaOH solution as compared with the plain sample. On the other hand, the composites were more prone to attack in H₂SO₄ solution, except for the Al₂O₃-2Ni-10RH composite sample which maintained its superiority over the plain counterpart.     

Evaluation of the corrosion resistance of phosphate coatings obtained by anodic electrochemical treatment

The corrosion resistance of phosphate coating obtained by anodic electrochemical treatment at 4–6 mA/cm² is addressed in this paper. The corrosion performance of these coatings is also compared with the coatings obtained by chemical treatment. The regenerated phosphoric acid under the influence of anodic current causes a large variation in morphological features of the coatings. Immersion and salt spray tests indicate the ability of these coatings to act as a barrier film on mild steel. Polarization and electrochemical impedance spectroscopic (EIS) studies indicate that the corrosion resistance of phosphate coatings obtained by anodic treatment decreases with increase in current density employed for deposition. In spite of their higher coating weight, the corrosion resistance of phosphate coatings obtained by anodic treatment is inferior to those obtained by chemical treatment. The porosity or discontinuities created due to the dissolution of the coating under the influence of anodic current are considered responsible for the inferior corrosion resistance of these coatings. The study concludes that anodic treatment has only a limited scope for preparing phosphate coatings with improved corrosion resistance.     

脉冲电流对锌酸盐镀锌层的影响

研究了在锌酸盐镀锌体系中采用脉冲电流时，脉冲频率，脉冲的占空比、反向电流对镀层外观，耐蚀性的影响，发现在最佳脉冲条件下得到的镀锌层比直流电镀得到的镀层光亮，结晶细致，耐蚀性能有很大的提高。     

镍-磷-硫酸钡化学复合镀层的研制

在由硫酸镍31g/L、次磷酸钠22g/L、乙醇酸30g/L、乙酸钠13g/L、二甲胺0.8g/L、全氟乙基碘化铵0.1g/L及重晶石(即硫酸钡)0～25g/L组成的稳定镀液中,采用化学镀的方法在低碳钢上制备了Ni-P-BaSO4复合镀层.其表面形貌采用扫描电镜进行分析,耐蚀性以动电位极化及电化学阻抗谱测试.镍-磷合金基...     

Synthesis and characterization of Ni-W/TiN nanocomposite coating with enhanced wear and corrosion resistance deposited by pulse electrodeposition

To enhance mechanical properties and anti-corrosion capability of Ni-W alloy further, Ni-W/TiN nanocomposite coating has been co-deposited via pulse current co-deposition in this work. The effects of TiN nanoparticles and operating parameters on the structure and properties of the deposited coating were examined. It illustrated that the nanocomposite coatings are uniform, dense and crack-free, exhibiting dome-like or hill-valley like structure. The particles were homogeneously incorporated in the metallic matrix. RTC analysis indicated that the preferred orientation of Ni-W/TiN was (111) texture. The crystallite size was of 10–16 nm, indicating the formation of nanocrystalline structure. TiN concentration, duty cycle and frequency could influence the amount of TiN particle and W element in the coating, then regulating hardness and anti-wear behaviors. The low duty cycle and long deposition time could diminish the roughness of the coating. The inclusion of TiN nanoparticles in the nickel matrix could promote the nucleation of fresh nickel crystals and restrict the growth of already formed nickel grains, favoring the homogeneous growth and grain refinement of Ni-W crystals. The doped TiN particles would favor the preferred orientation (111) plane, enhanced the hardness, wear and corrosion resistance of Ni-W alloy. Electrochemical results illustrated that the best corrosion-resistant properties of the nanocrystalline coating could be obtained at TiN 30 g L⁻¹, duty cycle of 20% and frequency of 60–200 Hz. The enhanced mechanical properties and corrosion resistance of Ni–W/TiN coating benefits its application in harsh corrosive environment.     

镍/纳米二氧化硅纳米复合镀层耐腐蚀性能的研究

制备了纳米氧化硅镍复合镀层材料,并利用静态浸泡法对纯镍镀层和由镀液中不同微粒含量制备的复合镀层样品的耐蚀性能进行了研究,讨论镀液中纳米微粒含量对镀层抗蚀性能的影响。并用扫描电镜观察镀层的表面形貌。     

A novel biomedical TiN-embedded TiO2 nanotubes composite coating with remarkable mechanical properties,corrosion, tribocorrosion resistance,and antibacterial activity

Tribocorrosion is a severe problem in dental implants, artificial joints, and other implants, and it will affect the long-term safety of the implants. To improve the deficiencies of titanium alloys, we combined physical vapor deposition technology and anodic oxidation to prepare TiN to embed TiO₂ nanotube composite coatings (NTNTs-TiN). Results show that the hardness of the NTNTs-TiN composite coatings reaches 33.2 ± 0.6 GPa, and the grains of the composite coatings were further refined. The NTNTs-TiN coating has the smallest average coefficient of friction (0.22) during tribocorrosion. The tribocorrosion resistance of NTNTs-TiN coating in SBF is increased by ∼44 and ∼2 times compared with Ti6Al4V alloy and TiN coating, respectively. The capillarity effect of the lower contact angle of NTNTs-TiN can form a continuous water-lubrication film at the interface between the counter-ball and coating and produce a lubrication film composed of Ca, Mg, and P, which reduces the coefficient of friction significantly. The NTNTs/TiN composite coating exhibits the best synergistic effect of wear and corrosion. In addition, the NTNTs-TiN coating also exhibits excellent antimicrobial and corrosion properties, which provides a new solution for the long-term safe use of implants in the human body.     

Vacuum thermal treated electroless NiP-TiO2 composite coatings

Composite NiP-TiO₂ layers were prepared by simultaneous electroless deposition of Ni-P and TiO₂ on steel substrate, from a solution in which TiO₂ particles were kept in suspension by stirring. Deposits were characterized for its structure, morphology and hardness. It was found that the chemical composition of Ni-P matrix has been influenced by the incorporation of TiO₂ particles. TiO₂ particle incorporation increases with increase in their bath concentrations (0.5-2.0 g/l). An improvement (up to 20%) in microhardness was observed in both as plated and vacuum heat-treated composite coatings compared to Ni-P coatings. Electroless deposited composite coatings exhibit an amorphous structure of the nickel matrix in which crystalline titanium oxide is incorporated. Vacuum heat treatment leads to the formation of a crystalline layer in which the Ni and Ni₃P crystallites appear apart from those of the TiO₂ (anatase). Potentiodynamic polarization measurements made on these deposits in 3.5 wt.% sodium chloride solution showed decrease in the corrosion resistance for the as-plated and heat-treated composite coatings.