An efficient method for a numerical description of virgin olive oil color with only two absorbance measurements

Four polynomial expressions are obtained that provide a good approximation and an easy, rapid calculation of the chromatic coordinates and the chroma—L ^*, a ^*, b ^*, and C—for the illuminant C and the standard observer, for a virgin or extra virgin olive oil; absorbance is measured at only 480 and 670 nm. These are as follows: L ^*=0.556458(A₄₈₀)²−2.51145A₄₈₀+0.55504(A₆₇₀)²−8.53016A₆₇₀+98.4089; a ^*=0.177372(A₄₈₀)²+2.1363A₄₈₀+1.43254(A₆₇₀)²−0.789231A₆₇₀−13.9246; b ^*=−16.0277(A₄₈₀)²+79.8932A₄₈₀−5.06558(A₆₇₀)²+3.36169A₆₇₀+31.9405; C=−15.8439(A₄₈₀)²+78.9312A₄₈₀−5.26784(A₆₇₀)²+3.56917A₆₇₀+33.3927. These give acceptable results, making the method a practical alternative to the extremely laborious Commission Internationale d’Eclairage (CIE) L ^* a ^* b ^* system, by which 391 absorbance values must be measured individually, nanometer by nanometer, before applying more complex equations. The validity of the proposed method has been confirmed by comparison, using a set of 20 sample oils different from the set of 25 oils used to generate the order of the equations. The variations between the values provided by the proposed and standard methods, respectively, had a mean of 0.00 for each of the chromatic variables—L ^* , a ^* , b ^* , and C; SD were moderate (0.71, 0.52, 1.22, and 1.22, respectively); the root mean square and the R ²-terms also confirmed the validity of the method.     

Electrochemical oxidation of an acid dye by active chlorine generated using Ti/Sn<Subscript>(1−<Emphasis Type="Italic">x</Emphasis>)</Subscript>Ir<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript>2</Subscript> electrodes

The generation of active chlorine on Ti/Sn_(1−x)Ir _x O₂ anodes, with different compositions of Ir (x = 0.01, 0.05, 0.10 and 0.30 ), was investigated by controlled current density electrolysis. Using a low concentration of chloride ions (0.05 mol L⁻¹) and a low current density (5 mA cm⁻²) it was possible to produce up to 60 mg L⁻¹ of active chlorine on a Ti/Sn_0.99Ir_0.01O₂ anode. The feasibility of the discoloration of a textile acid azo dye, acid red 29 dye (C.I. 16570), was also investigated with in situ electrogenerated active chlorine on Ti/Sn_(1−x)Ir _x O₂ anodes. The best conditions for 100% discoloration and maximum degradation (70% TOC reduction) were found to be: NaCl pH 4, 25 mA cm⁻² and 6 h of electrolysis. It is suggested that active chlorine generation and/or powerful oxidants such as chlorine radicals and hydroxyl radicals are responsible for promoting faster dye degradation. Rate constants calculated from color decay versus time reveal a zero order reaction at dye concentrations up to 1.0 × 10⁻⁴ mol L⁻¹. Effects of other electrolytes, dye concentration and applied density currents also have been investigated and are discussed.     

Application of magnetite modified with aluminum/silica to adsorb phosphate in aqueous solution

BACKGROUND: Phosphate is one of the main contaminants responsible for the eutrophication of surface waters, and adsorption is a potential treatment method for this pollutant. A magnetic adsorbent manufactured from magnetite (Fe₃O₄) can be recovered easily from treated water by magnetic force, without requiring further downstream treatment. In this research, the surface of magnetite modified with aluminum and silica (Al/SiO₂/Fe₃O₄) was used to adsorb phosphate in an aqueous solution in a batch system. RESULTS: The optimum solution pH for phosphate adsorption by Al/SiO₂/Fe₃O₄ was found to be 4.5. The phosphate adsorption behavior of Al/SiO₂/Fe₃O₄ was in good agreement with both the Langmuir and Freundlich adsorption isotherm, and the maximum adsorption capacity (q_m) and Gibbs free energy of phosphate was 25.64 mg g^?1 and ? 21.47 kJ mol^?1, respectively. A pseudo‐second‐order model could best describe the adsorption kinetics, and the derived activation energy was 3.52 kJ mol^?1. The optimum condition to desorb phosphate from Al/SiO₂/Fe₃O₄ is provided by a solution with 0.05 mol L^?1 NaOH. CONCLUSIONS: Magnetic adsorbent is a potential material for a water treatment method. The results of this study will be helpful in the development of aluminum modified silica magnetic adsorbents that can be used to remove phosphate in aqueous solution. Copyright © 2011 Society of Chemical Industry     

Preparation of ferric oxide powders by ultrasonic-assisted impinging stream reaction

In this paper, Fe₃O₄ powder was prepared by the chemical precipitation method using impinging stream technology. The influences of feed flow rate, L/D, reactant concentration, ratio of iron ion concentration, reaction temperature, and impact time on the size and distribution of particles were investigated by the orthogonal experiment method. The microstructure and morphology of Fe₃O₄ powders were characterized by scanning electron microscopy, X-ray diffractometer, and granulometer. The results showed that when ratio of iron ion concentration c(Fe²⁺):c(Fe³⁺) = 0.75, reactant concentration c(Fe³⁺) = 0.4 mol · L⁻¹, feed flow rate Q = 800 L · h⁻¹, L/D = 3, reaction temperature T = 20°C, impact time t = 50 min, the prepared Fe₃O₄ had an average particle size of 1.815 μm and the most uniform distribution. The influence of ultrasonic enhancement on the mixing process and powder preparation in an impinging stream reactor was investigated. The size and distribution of the powders were significantly affected by ultrasonic enhancement. With the increase in ultrasonic power, the particle size of the powders decreased and the distribution became narrower. The particle size was reduced by 68.78%, and the particle distribution range was narrowed by 84.34% under ultrasound enhancement. This study promised the effective utilization of ultrasonic cavitation in the optimization of experimental equipment and the preparation of ultrafine powder, which provides a basis for process optimization of powder preparation.     

Electrochemical properties of Li1?z(Ni1?yFey)1+zO2 synthesized by the combustion method in an air atmosphere

For the syntheses of LiNi_1−y Fe _y O₂ (0.000 ≤ y ≤ 0.300), mixtures of the starting materials with the desired compositions were preheated in an air atmosphere at 400 °C for 30 min and calcined in air at 700 °C for 48 h. The phases appearing in the intermediate reaction steps for the formation of lithium nickel oxide are deduced from the DTA analysis. XRD analysis, FE-SEM observation, FTIR analysis and electrochemical measurement were performed for the synthesized Li_1−z (Ni_1−y Fe _y )_1+z O₂ (0.000 ≤ y ≤ 0.300) samples. The samples of Li_1−z (Ni_1−y Fe _y )_1+z O₂ with y = 0.025 and 0.050 have higher first discharge capacities than Li_1−z (Ni_1−y Fe _y )_1+z O₂ with y = 0.000 and better or similar cycling performance at the 0.1 C rate in the voltage range of 2.7–4.2 V. Similar results have not previously been reported except for Co-substituted LiNiO₂. The sample Li_1−z (Ni_0.975Fe_0.025)_1+z O₂ has the highest first discharge capacity (176.5 mAh g⁻¹). Rietveld refinement of the XRD patterns of LiNi_1−y Fe _y O₂ (0.000 < y ≤ 0.100) from a starting structure model [Li,Ni]_3b[Li,Ni,Fe]_3a[O₂]_6c showed that cation disordering occurred in the samples.     

Epoxidation of karanja (Pongamia glabra) oil by H2O2

Epoxidation of karanja oil (KO), a nondrying vegetable oil, was carried out with peroxyacetic acid that was generated in situ from aqueous hydrogen peroxide and glacial acetic acid. KO contained 61.65% oleic acid and 18.52% linoleic acid, respectively, and had an iodine value of 89 g/100 g. Unsaturated bonds in the oil were converted to oxirane by epoxidation. Almost complete epoxidation of ethylenic unsaturation was achieved. For example, the iodine value of the oil could be reduced from 89 to 19 by epoxidation at 30°C. The effects of temperature, hydrogen peroxide-to-ethylenic unsaturation ratio, acetic acid-to-ethylenic unsaturation ratio, and stirring speed on the epoxidation rate and on oxirane ring stability were studied. The rate constant and activation energy for epoxidation of KO were 10⁻⁶ L·mol⁻¹·s⁻¹ and 14.9 kcal·mol⁻¹, respectively. Enthalpy, entropy, and free energy of activation were 14.2 kcal·mol⁻¹, −51.2 cal·mol⁻¹·K⁻¹, and 31.1 kcal·mol⁻¹, respectively. The present study revealed that epoxides can be developed from locally available natural renewable resources such as KO.     

Studies on the radical polymerization of N-vinyl 2-pyrrolidone initiated by diphenyl ditelluride

N-vinyl pyrrolidone (NVP) was polymerized in dioxan at 60 ± 0.1°C for 1 h using diphenyl ditelluride as radical initiator. The system follows ideal kinetics i.e. R _p α [DPDT]^0.5[NVP]. The activation energy and dissociation constant is computed as 46 kJ mol⁻¹ and 1.1 × 10⁻¹¹ s⁻¹, respectively. The polymer was characterized with the help of FTIR, ¹H-NMR, ¹³C-NMR, ESR spectroscopy. The FT-IR spectrum showed bands at 1660–1680 cm⁻¹ due to combination of >C = O and C–N stretching. The gyromagnetic constant ‘g’ has been computed as 2.2203. The main product of this reaction were poly(N-vinylpyrrolidone)s with phenyl tellanyl ends. The presence of tellurium in polymer is confirmed by ICP analysis. The DSC shows the T _g of poly(N-vinylpyrrolidone) is 168°C due to rigid pyrrolidane group. The TGA showed that polymer was stable up to 380°C.The GPC studies showed that the weight average molecular weight decreases with increase of [DPDT].     

Efficiency and Mechanism of Ciprofloxacin Hydrochloride Degradation in Wastewater by Fe3o4/Na2S2O8

ABSTRACT

The nanosized Fe₃O₄ catalyst was synthesized via a modified reverse coprecipitation method and characterized by means of a scanning electron microscope (SEM) and an X-ray diffraction (XRD) analysis instrument. The degradation efficiency and reaction rate of Fe₃O₄ in activating sodium persulfate used to degrade ciprofloxacin were determined from the catalyst dosage, oxidant concentration, and initial pH. The results showed that under the optimum conditions of a catalyst dosage of 2.0 g·L^?1, a sodium persulfate concentration of 1.0 g·L^?1, and an initial pH of 7, the degradation rate of ciprofloxacin was 93.73%, the removal rate of total organic carbon was 78%, and the first-order reaction constant was 0.06907 min^?1 within 40 min. It was also demonstrated that the reactive oxygen species in the Fe₃O₄/sodium persulfate catalytic system were mainly composed of SO₄^– and supplemented by OH· and HO₂· using probe compounds such as ethanol, tertiary butanol, and benzoquinone.     

Electrochemical properties of cathode materials LiNi1−y Co y O2 synthesized using various starting materials

LiNi_1−y Co _y O₂ samples were synthesized at 800 °C and 850 °C, by the solid-state reaction method, using the starting materials LiOH·H₂O, Li₂CO₃, NiO, NiCO₃, Co₃O₄ and CoCO₃. The LiNi_1−y Co _y O₂ synthesized using Li₂CO₃, NiO and Co₃O₄ exhibited the α-NaFeO₂ structure of the rhombohedral system (space group ). As the Co content increased, the lattice parameters a and c decreased. The reason is that the radius of the Co ion is smaller than that of the Ni ion. The increase in c/a shows that a two-dimensional structure develops better as the Co content increases. The LiNi_0.7Co_0.3O₂ synthesized at 800 °C using LiOH · H₂O, NiO and Co₃O₄ exhibited a larger first discharge capacity of 162 mAh g⁻¹ than the other samples. The cycling performances of the samples with the first discharge capacity larger than 150 mAh g⁻¹ were investigated. LiNi_0.9Co_0.1O₂ synthesized at 850 °C using Li₂CO₃, NiO and Co₃O₄ showed excellent cycling performance. Samples with larger first discharge capacity will have a greater tendency for lattice destruction due to expansion and contraction during intercalation and deintercalation, than samples with smaller first discharge capacity. As the first discharge capacity increases, the capacity fading rate thus increases.     

A novel platform of hemoglobin on core–shell structurally Fe3O4@Au nanoparticles and its direct electrochemistry

A novel platform, which hemoglobin (Hb) was immobilized on core–shell structurally Fe₃O₄/Au nanoparticles (simplified as Fe₃O₄@Au NPs) modified glassy carbon electrode (GCE), has been developed for fabricating the third biosensors. Fe₃O₄@Au NPs, characterized using transmission electron microscope (TEM), scanning electron microscope (SEM) and energy dispersive spectra (EDS), were coated onto GCE mediated by chitosan so as to provide larger surface area for anchoring Hb. The thermodynamics, dynamics and catalysis properties of Hb immobilized on Fe₃O₄@Au NPs were discussed by UV–visible spectrum (UV–vis), electrochemical impedance spectroscopy (EIS), electrochemical quartz crystal microbalance technique (EQCM) and cyclic voltammetry (CV). The electrochemical parameters of Hb on Fe₃O₄@Au NPs modified GCE were further carefully calculated with the results of the effective working area as 3.61 cm², the surface coverage concentration (Γ) as 1.07 × 10⁻¹² mol cm⁻², the electron-transfer rate constant (K_s) as 1.03 s⁻¹, the number of electron transferred (n) as 1.20 and the standard entropy of the immobilized Hb (ΔS⁰′) as calculated to be −104.1 J mol⁻¹ K⁻¹. The electrocatalytic behaviors of the immobilized Hb on Fe₃O₄@Au NPs were applied for the determination of hydrogen peroxide (H₂O₂), oxygen (O₂) and trichloroacetic acid (TCA). The possible functions of Fe₃O₄ core and Au shell as a novel platform for achieving Hb direct electrochemistry were discussed, respectively.     

Kinetics of the formation of symmetrical wax esters from the corresponding alcohols with the use of hydrobromic acid and hydrogen peroxide

The primary aliphatic alcohols n-octanol, n-decanol, and n-dodecanol have been converted to their corresponding symmetrical esters by using HBr and H₂O₂ in the absence of a solvent. The reaction was carried out at 30, 40, and 50°C and at mole ratios of alcohol to HBr of 1∶0.1, 1∶0.2, 1∶0.3, and 1∶0.5. The rate of the reaction was found to increase with increase in the reaction temperature and concentration of HBr. The maximal conversion of n-octanol was 72% at 40°C and a mole ratio of n-octanol to HBr of 1∶0.5. The kinetics of the reaction have been established, and the reaction was found to be first-order with respect to alcohol and bromine concentration in the organic phase, and second-order with respect to both. The second-order rate constants for n-octanol, n-decanol, and n-dodecanol are 27.08, 32.58, and 37.42 mL mol⁻¹ min⁻¹, respectively, at 40°C. The activation energy for the esterification reaction of n-octanol was found to be 16.32 kcal mol⁻¹.     

Extraction of Uranium(VI) and Thorium(IV) from Nitric Acid Solution by N,N,N′,N′ – Tetraoctylglutaricamide

Synthesis and characterization of N,N,N′,N′-tetraoctylglutaricamide (TOGA) was carried out and used for extraction of U(VI) and Th(IV) from nitric acid solutions. The processes of extraction were determined by the slope analysis and by analyzing a function that allows the simultaneous treatment of all the experimental points obtained in different conditions. The different factors affecting the extraction distribution ratio(D) of U(VI) and Th(IV) (extraction concentration, concentrations of nitric acid, salting-out agent NaNO₃ concentration, equilibration time, temperature, and types of diluents) were investigated. The results obtained indicated that the extraction species of U(VI) and Th(IV) are mainly extracted as UO₂(NO₃)₂·1.0TOGA and Th(NO₃)₄·1.5TOGA. The apparent equilibrium constant of U(VI) and Th(IV) extraction determined are 3.35 ± 0.03 L³/mol³ and 1.87 ± 0.01 L⁵/mol⁵ at 298 ± 1 K. Thermodynamic parameters such as the free energy(ΔG), enthalpy(ΔH), and entropy(ΔS) changes associated with the extraction processes could be evaluated. Back-extraction of U(VI) and Th(IV) from organic phases was also studied.     

Kinetics of leaching of tunisian phosphate ore particles in dilute phosphoric acid solutions

Van der Sluis et al.'s model was used to determine the rate of the partial dissolution of a Tunisian phosphate rock with dilute phosphoric acid (1.5 mass% P₂O₅). When the temperature rises from 25 to 90°C, for a given particle size, the mass-transfer coefficients, k_L°, vary from 3 × 10^?3 to 8 × 10^?3 m ·s^?1. The corresponding diffusion coefficients, D, lies between 6 × 10^?7 and 27 × 10^?7 m²·s^?1. Activation energy is equal to 14 kJ·mol^?1 and values of k_L°, at 25°C, are in the range of 0.28 × 10^?3 and 4 × 10^?3 m·s^?1 when the agitation speed goes from 220 to 1030 rpm, showing that the leaching process is controlled by diffusion rather than by chemical reaction.     

Catalytic Oxidation of CO Gas over Nanocrystallite Cu x Mn1−x Fe2O4

The catalytic oxidation of CO over nanocrystallite Cu _x Mn_(1−x)Fe₂O₄ powders was studied using advanced quadruple mass gas analyzer system. The oxidation of CO to CO₂ was investigated as a function of reactants ratio and firing temperature of ferrite powders. The maximum CO conversion was observed for ferrite powders which have equal amount of Cu²⁺ and Mn²⁺ (Cu_0.5Mn_0.5Fe₂O₄). The high catalytic activity of Cu_0.5Mn_0.5Fe₂O₄ can be attributed to the changes of the valence state of catalytically active components of the ferrite powders. The firing temperature plays insignificant role in the catalytic activity of CO over nanocrystallite copper manganese ferrites. The mechanism of catalytic oxidation reactions was studied. It was found that the CO catalytic oxidation reactions on the surface of the Cu _x Mn_1−x Fe₂O₄ was done by the reduction of the ferrite by CO to the oxygen deficient lower oxide then re-oxidation of this phase to the saturated oxygen metal ferrite again.     

Electrochemical biosensors utilizing the electron transfer of hemoglobin immobilized on cobalt-substituted ferrite nanoparticles–chitosan film

Cobalt ferrite nanoparticles (Co_xFe_3−xO₄) and chitosan (CS) film were used to immobilize/adsorb hemoglobin (Hb) to create a protein electrode to study the direct electron transfer between the redox centers of the proteins and the electrode. X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed that the Co_xFe_3−xO₄ particles were nanoscale in size and formed an ordered layered structure. The native structure of the immobilized Hb was preserved as indicated by Fourier-transform infrared (FTIR) and UV–visible (UV–vis) spectroscopy. The Hb-Co_xFe_3−xO₄–CS modified electrode showed a pair of well-defined and quasi-reversible cyclic voltammetric peaks at −0.373 V (vs. SCE) and exhibited appreciable electrocatalytic activity for the reduction of H₂O₂. The catalysis currents increased linearly with H₂O₂ concentration in a wide range of 5.0 × 10⁻⁸ to 1.0 × 10⁻³ mol L⁻¹ with a detection limit of 1.0 × 10⁻⁸ mol L⁻¹ (S/N = 3) and had long-term stability. Finally, the proposed method was applied to investigate the coexistence of hydrogen peroxide with the interfering substances. Experimental results showed that the ascorbic acid, glucose, l-cysteine, uric acid, and dopamine at corresponding concentrations did not influence the detection of H₂O₂.     

Magnetite/poly(D,L-lactide-co-glycolide) and hydroxyapatite/poly(D,L-lactide-co-glycolide) prepared by W/O/W emulsion technique for drug carrier: Evaluation of in vitro release of dexamethasone from composite nanoparticles

Biocompatible polymeric carriers containing inorganic materials for delivering therapeutic agents to a targeted site are promising candidate for drug delivery. Two nanocomposite nanoparticles, magnetite/poly(D,L-lactide-co-glycolide) and hydroxyapatite/poly(D,L-lactide-co-glycolide) (Fe₃O₄/PLGA and HAp/PLGA, respectively), with different weight ratios of inorganics to polymer and different polymer molecular weights were prepared by water-in-oil-in-water (W/O/W) emulsion technique to determine incorporation and in vitro release profile of the small molecule drugs water-insoluble dexamethasone acetate (DEX-Ac) and water-soluble dexamethasone phosphate (DEX-P). The in vitro release for DEX-Ac nanoparticles showed an initial burst release followed by a continuous slower release, whereas DEX-P nanoparticles showed only rapid initial release behavior.     

Syntheses and Structural Characterization of Co(II) Coordination Polymers Supported by Bis(<Emphasis Type="Italic">N</Emphasis>-benzimidazolyl)methane and Bis(<Emphasis Type="Italic">N</Emphasis>-imidazolyl)methane

[Co₂(L¹)₂(NCS)₄]·4MeOH 1, [Co(L²)₂(H₂O)₂](Sal)₂·4H₂O (Sal = salicylate) 2 were obtained from self-assembly of the cobalt salts with bis(N-benzimidazolyl)methane (L¹), and bis(N-benzimidazolyl)methane (L²), and their structures were characterized by IR and X-ray diffraction analysis. Complex 1 exhibits a two-dimensional grid structure, whereas complex 2 is a coordination polymer having a one-dimensional linear chain structure. The grid in 1 lies parallel to the crystallographic ab plane and exhibits intra-grid M–M separations of 10.508 × 10.508 Å. Hydrogen bonds hold the cationic chains in 2 together leading to a three-dimensional network structure.     

Humid aging of polyetherimide. I. Water sorption characteristics

The sorption and desorption kinetics of water into polyetherimide (ULTEM 1000) were studied at various temperatures ranging from 20 to 100°C. The water equilibrium concentration increases slightly with temperature from 1.39% (by weight) at 20°C to 1.50% at 100°C. The solubility coefficient, S, calculated from these data, and the water vapor pressure decrease with temperature. The calculated heat of dissolution H_s is close to −43 kJ mol⁻¹, which explains the low effect of temperature on the equilibrium concentration. The diffusion coefficient, D, varies from about 1.10⁻¹² m² · s⁻¹ at 20°C to about 16.10⁻¹² m² · s⁻¹ at 100°C. The apparent activation energy of diffusion, E_D, and the heat of dissolution, H_s, of water in the polymer have opposite values (respectively, +43 and −42 kJ · mol⁻¹). From this observation and a comparison of these data with water diffusion characteristics in other glassy polar polymers, it is hypothesized that the transport rate of water is kinetically controlled by the dissociation of water–polymer complexes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1439–1444, 2000     

Phthalic Acid Induces Oxidative Stress and Alters the Activity of Some Antioxidant Enzymes in Roots of <Emphasis Type="Italic">Malus prunifolia</Emphasis>

Apple replant is a widespread agricultural problem documented in all of the major fruit-growing regions of the world. In order to better understand the phytotoxic mechanisms induced by allelochemicals involved with this problem, Malus prunifolia plants were grown hydroponically to the six-leaf-stage in the presence of phthalic acid (0 or 1 mM) for 5, 10, or 15 days. Apple plants were evaluated for: shoot and root length, fresh and dry weight, malondialdehyde (MDA) content, hydrogen peroxide (H₂O₂) content, superoxide radical (O₂ ^·−) generation rate, and antioxidant enzyme activities. Shoot and root lengths and fresh and dry weights of M. prunifolia decreased in plants exposed to phthalic acid. MDA and H₂O₂ content increased in phthalic acid-treated plants as did the generation rate of O₂ ^·− in M. prunifolia roots. The activities of superoxide dismutase (EC 1.15.1.1), peroxidase (EC 1.11.1.7), catalase (EC 1.11.1.6), ascorbate peroxidase (EC 1.11.1.11), glutathione reductase (EC 1.6.4.2), dehydroascorbate reductase (EC 1.8.5.1), and monodehydroascorbate reductase (EC 1.6.5.4) increased in phthalic acid-stressed roots compared with control roots. These results suggest that activation of the antioxidant system by phthalic acid led to the formation of reactive oxygen species that resulted in cellular damage and the decrease of M. prunifolia growth.     

Preparation, electrochemical properties, and cycle mechanism of Li1? x Fe0.8Ni0.2O2-Li x MnO2 (Mn/(Fe+Ni+Mn)=0.8) material

A new type of Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ (Mn/(Fe+Ni+Mn)=0.8) material was synthesized at 350 °C in an air atmosphere by a solid-state reaction. The material had an XRD pattern that closely resembled that of the original Li_1−x FeO₂-Li _x MnO₂ ((Fe+Ni+Mn)=0.8) with much reduced impurity peaks. It was composed of many large particles of about 500–600 nm and small particles of about 100–200 nm, which were distributed among the larger particles. The Li/Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ cell showed a high initial discharge capacity above 192 mAh/g, which was higher than that of the parent Li/Li_1−x FeO₂-Li _x MnO₂ (186 mAh/g). This cell exhibited not only a typical voltage plateau in the 2.8 V region, but also an excellent cycle retention rate (96%) up to 45 cycles. We suggest a unique role of doped nickel ion in the Li/Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ cell, which results in the increased initial discharge capacity from the redox reaction of Ni²⁺/Ni³⁺ between 2.0 and 1.5 V region.