Size-selective sampling performance of six low-volume “total” suspended particulate (TSP) inlets

Several low-volume inlets (flow rates ≤ 16.7 liters per minute (Lpm)) are commercially available as components of low-cost, portable ambient particulate matter samplers. Because the inlets themselves do not contain internal fractionators, they are often assumed to representatively sample “total” mass concentrations from the ambient air, independent of aerodynamic particle size and wind speed. To date, none of these so-called “TSP” inlets have been rigorously tested under controlled conditions. To determine their actual size-selective performance under conditions of expected use, wind tunnel tests of six commonly used omnidirectional, low-volume inlets were conducted using solid, polydisperse aerosols at wind speeds of 2, 8, and 24 km/h. With the exception of axially-oriented, isokinetic sharp-edge nozzles operating at 5 and 10 Lpm, all low-volume inlets showed some degree of nonideal sampling performance as a function of aerodynamic particle size and wind speed. Depending upon wind speed and assumed ambient particle size distribution, total mass concentration measurements were estimated to be negatively biased by as much as 66%. As expected from particle inertial considerations, inlet efficiency tended to degrade with increasing wind speed and particle size, although some exceptions were noted. The implications of each inlet's non-ideal behavior are discussed with regards to expected total mass concentration measurement during ambient sampling and the ability to obtain representative sampling for size ranges of interest, such as PM_2.5 and PM₁₀. Overall test results will aid in low-volume inlet selection and with proper interpretation of results obtained with their ambient field use.

Copyright © 2018 American Association for Aerosol Research     

Numerical,wind-tunnel,and atmospheric evaluation of a turbulent ground-based inlet sampling system

The use of inlets for transferring aerosols from the environment to instrumentation can introduce uncertainty in the measurement of aerosol properties. Aerosol loss during this process is a non-negligible issue that may bias the subsequent measurements. These loss mechanisms include aspiration at the inlet head and deposition/evaporation/condensation during transport through the sampling lines. Coarse-mode aerosol is significantly impacted by the aspiration and inertial loss mechanisms within an inlet system. This work uses wind tunnel experiments to investigate aerosol losses through the Storm Peak Laboratory’s (SPL) new aerosol inlet system. The inlet is used extensively for both intensive field campaigns and long-term aerosol monitoring. The results of numerical simulations of the SPL aerosol inlet sampling efficiency are provided at several wind speeds, and experimental results demonstrate the system has a 50% cut off for the coarse-mode at an aerodynamic diameter of approximately 13?μm and wind speed of 0.5?m s^?1. This investigation will lead to improved accuracy of in situ aerosol measurements at SPL and this system can be replicated at other atmospheric stations.

Copyright © 2019 American Association for Aerosol Research     

Effect of a Horizontal Inlet on the Collection Efficiency of a Rectangular-Slit-Nozzle Impactor

A horizontal inlet was employed to improve the collection efficiency of a rectangular-slit-nozzle impactor. A numerical and experimental study of the collection efficiency of rectangular-slit-nozzle impactors, with either typical inlets or horizontal inlets, was conducted. In the comparison of typical inlet impactors and horizontal-inlet impactors, parameters such as the nozzle width, impaction plate width, nozzle-to-plate distance, and aerosol flow rate were held constant, and only the inlet shape was changed. A parametric study was conducted to examine the effects of the horizontal inlet dimensions on the collection efficiency of rectangular-slit-nozzle impactors. It was found that a horizontal inlet could reduce the square root of the Stokes number corresponding to the cutoff size from 0.77 to 0.60, compared with a typical inlet.

Copyright 2014 American Association for Aerosol Research     

Large Particle Penetration During PM10 Sampling

The objective of the present study was to characterize the performance of a federal reference method (FRM) PM₁₀ size-selective inlet using analysis methods designed to minimize uncertainty in measured sampling efficiencies for large particles such as those most often emitted from agricultural operations. The performance of an FRM PM₁₀ inlet was characterized in a wind tunnel at a wind speed of 8 km/h. Data were also collected for 20 and 25 μm particles at wind speeds of 2 and 24 km/h. Results of the present sampler evaluation compared well with those of previous studies for a similar inlet near the cutpoint, and the sampler passed the criteria required for certification as a FRM sampler when tested at 8 km/h. Sampling effectiveness values for particles with nominal diameters of 20 and 25 μm exceeded 3% for 8 and 24 km/h wind speeds in the present study and were statistically higher than both the “ideal” PM₁₀ sampler (as defined in 40 CFR 53) and the ISO (1995) standard definition of thoracic particles (p < 0.05) for 25 μm particles leading to the potential for significant sampling bias relative to the “ideal” PM₁₀ sampler when measuring large aerosols.

Copyright 2014 American Association for Aerosol Research     

A practical set of miniaturized instruments for vertical profiling of aerosol physical properties

In situ atmospheric aerosol measurements have been performed from a Manta unmanned aircraft system (UAS) using recently developed miniaturized aerosol instruments. Flights were conducted up to an altitude of 3000 m (AMSL) during spring 2015 in Ny-Ålesund, Svalbard, Norway. We use these flights to demonstrate a practical set of miniaturized instruments that can be deployed onboard small UASs and can provide valuable information on ambient aerosol. Measured properties include size-resolved particle number concentrations, aerosol absorption coefficient, relative humidity, and direct sun intensity. From these parameters, it is possible to derive a comprehensive set of aerosol optical properties: aerosol optical depth, single scattering albedo, and asymmetry parameter. The combination of instruments also allows us to determine the aerosol hygroscopicity.

Copyright © 2017 American Association for Aerosol Research     

Seasonal Variability of Particle-Associated Organic Compounds Near a Heavily Traveled Secondary Road

Size-resolved aerosol samples were collected both upwind and downwind of a large secondary road in the winter and spring of 2007 to assess contributions of on-road emissions to ambient aerosols. The aerosol samples were extracted and analyzed for a wide variety of organic compounds including polycyclic aromatic hydrocarbons (PAHs), alkanes, sugars, and organic acids. The results showed a strong seasonal pattern where the concentrations of most compounds were higher in winter than in spring. Some of the biogenic sugars were the exception, which might be the result of a “spring blooming season.” The surprising result was that the upwind site located in a residential neighborhood had very similar concentrations of most organic compounds compared to the near-roadway site. Possible reasons for the lack of differences in organic chemical concentrations between the near-road and control sites include: a large urban background concentration of aerosols superimposed on any local source; shifting wind directions that make the “downwind” site upwind during the night; and additional local sources in the residential neighborhood such as wood burning in winter.

Copyright 2014 American Association for Aerosol Research     

Application of centrifugal filter to aerosol size distribution measurement

In the present work, the centrifugal filter proposed by the authors was applied to classify aerosol particles followed by the detection of total mass or number concentrations so as to measure the size distribution of aerosol particles. The structure and operating condition of the centrifugal filter were optimized in order to attain sharp separation curves with various cut-off sizes between 0.3 and 10 μm. The aerosol penetrating the centrifugal filter at various rotation speeds was measured with a photometer to determine the total mass concentration. The virtue of this system is that the cut-off size is varied just by scanning the rotation speed of filter and that it can be applied to the measurement of high concentration aerosols without dilution by choosing an appropriate filter medium. As a result, the centrifugal filter was successfully applied to measure the size distribution of solid particles in size ranging from 0.3 to 10 μm.

Copyright © 2017 American Association for Aerosol Research     

Characterization and Response Model of the PPS-M Aerosol Sensor

The Pegasor PPS-M sensor is an electrical aerosol sensor based on diffusion charging and current measurement without particle collection. In this study, the role and effect of each component in the instrument is discussed shortly and the results from a thorough calibration measurements are presented. A comprehensive response model for the operation of the PPS-M sensor was developed based on the calibration results and computational fluid dynamics (CFD) modeling results. The obtained response model, covering the effects of the particle charger, the mobility analyzer, and both diffusion and inertial losses, was tested in the laboratory measurements with polydisperse test aerosols, where a good correlation between the model and the measured results was found.

Copyright 2014 American Association for Aerosol Research     

Design and evaluation of an aerodynamic focusing micro-well aerosol collector

Aerosol sampling and identification is vital for the assessment and control of particulate matter pollution, airborne pathogens, allergens, and toxins and their effect on air quality, human health, and climate change. In situ analysis of chemical and biological airborne components of aerosols on a conventional filter is challenging due to dilute samples in a large collection region. We present the design and evaluation of a micro-well (µ-well) aerosol collector for the assessment of airborne particulate matter (PM) in the 0.5–3 µm size range. The design minimizes particle collection areas allowing for in situ optical analysis and provides an increased limit of detection for liquid-based assays due to the high concentrations of analytes in the elution/analysis volume. The design of the collector is guided by computational fluid dynamics (CFD) modeling; it combines an aerodynamic concentrator inlet that focuses the aspirated aerosol into a narrow beam and a µ-well collector that limits the particle collection area to the µ-well volume. The optimization of the collector geometry and the operational conditions result in high concentrations of collected PM in the submillimeter region inside the µ-well. Collection efficiency experiments are performed in the aerosol chamber using fluorescent polystyrene microspheres to determine the performance of the collector as a function of particle size and sampling flow rate. The collector has the maximum collection efficiency of about 75% for 1 µm particles for the flow rate of 1 slpm. Particles bigger than 1 µm have lower collection efficiencies because of particle bounce and particle loss in the aerodynamic focusing inlet. Collected samples can be eluted from the device using standard pipettes, with an elution volume of 10–20 µL. The transparent collection substrate and the distinct collection region, independent of particle size, allows for in situ optical analysis of the collected PM.

© 2017 American Association for Aerosol Research     

Opto-aerodynamic focusing of aerosol particles

We describe a new method for focusing and concentrating a stream of moving micron-sized aerosol particles in air. The focusing and concentrating process is carried out by the combined drag force and optical force that is generated by a double-layer co-axial nozzle and a focused doughnut-shaped hollow laser beam, respectively. This method should supply a new tool for aerosol science and related research.

Copyright © 2018 American Association for Aerosol Research     

Generation of monodisperse aerosols by combining aerodynamic flow-focusing and mechanical perturbation

A novel instrument has been developed for generating highly monodisperse aerosol particles with a geometrical standard deviation of 1.05 or less. This aerosol generator applies a periodic mechanical excitation to a micro-liquid jet obtained by aerodynamic flow-focusing. The jet diameter and its fastest growth wavelength have been optimized as a function of the flow-focusing pressure drop and the liquid flow rate. The monodisperse aerosol generated by this instrument is also charge neutralized with bipolar ions produced by a non-radioactive, corona discharge device. Monodisperse droplet generation in the 15- to 72-μm diameter range from a single 100-micron nozzle has been demonstrated. Both liquid and solid monodisperse particles can be generated from 0.7- to 15-μm diameter by varying solution concentration, liquid flow rate, and excitation frequency. The calculated monodisperse particle diameter agrees well with independent measurements. The operation of this new monodisperse aerosol generator is stable and reliable without nozzle clogging, typical of other aerosol generators at the lower end of the operating particle size ranges.

Copyright © 2016 American Association for Aerosol Research     

Inter-comparison of low-cost sensors for measuring the mass concentration of occupational aerosols

Low-cost sensors are effective for measuring the mass concentration of ambient aerosols and second-hand smoke in homes, but their use at concentrations relevant to occupational settings has not been demonstrated. We measured the concentrations of four aerosols (salt, Arizona road dust, welding fume, and diesel exhaust) with three types of low-cost sensors (a DC1700 from Dylos and two commodity sensors from Sharp), an aerosol photometer, and reference instruments at concentrations up to 6500 µg/m³. Raw output was used to assess sensor precision and develop equations to compute mass concentrations. EPA and NIOSH protocols were used to assess the mass concentrations estimated with low-cost sensors compared to reference instruments. The detection efficiency of the DC1700 ranged from 0.04% at 0.1 µm to 108% at 5 µm, as expected, although misclassification of fine and coarse particles was observed. The raw output of the DC1700 had higher precision (lower coefficient of variation, CV = 7.4%) than that of the two sharp devices (CV = 25% and 17%), a finding attributed to differences in manufacturer calibration. Aerosol type strongly influenced sensor response, indicating the need for on-site calibration to convert sensor output to mass concentration. Once calibrated, however, the mass concentration estimated with low-cost sensors was highly correlated with that of reference instruments (R²= 0.99). These results suggest that the DC1700 and Sharp sensors are useful in estimating aerosol mass concentration for aerosols at concentrations relevant to the workplace.

© 2016 American Association for Aerosol Research     

Advanced aerosol optical tweezers chamber design to facilitate phase-separation and equilibration timescale experiments on complex droplets

The phase-separation of mixed aerosol particles and the resulting morphology plays an important role in determining the interactions of liquid aerosols with their gas-phase environment. We present the application of a new aerosol optical tweezers chamber for delivering a uniformly mixed aerosol flow to the trapped droplet's position for performing experiments that determine the phase-separation and resulting properties of complex mixed droplets. This facilitates stable trapping when adding additional phases through aerosol coagulation, and reproducible measurements of the droplet's equilibration timescale. We demonstrate the trapping of pure organic carbon droplets, which allows us to study the morphology of droplets containing pure hydrocarbon phases to which a second phase is added by coagulation. A series of experiments using simple compounds are presented to establish our ability to use the cavity enhanced Raman spectra to distinguish between homogeneous single-phase, and phase-separated core–shell or partially engulfed morphologies. The core–shell morphology is distinguished by the pattern of the whispering gallery modes (WGMs) in the Raman spectra where the WGMs are influenced by refraction through both phases. A core–shell optimization algorithm was developed to provide a more accurate and detailed analysis of the WGMs than is possible using the homogeneous Mie scattering solution. The unique analytical capabilities of the aerosol optical tweezers provide a new approach for advancing our understanding of the chemical and physical evolution of complex atmospheric particulate matter, and the important environmental impacts of aerosols on atmospheric chemistry, air quality, human health, and climate change.

Copyright © 2016 American Association for Aerosol Research     

The correlation between acoustic streaming patterns and aerosol removal efficiencies in an acoustic aerosol removal system

Recently, researchers proposed that a second-order effect, acoustic streaming, induced aerosol depositions as a noninvasive aerosol removal technique. However, the acoustic streaming patterns, which determined the deposition efficiencies, were merely observed but not investigated. This article studied this correlation by both experimental and numerical methods. By keeping the sound frequency and sound pressure level constant, the acoustic streaming field was varied by the dimensions of the air duct and ultrasonic radiating plate. The numerical model was validated by the experimental results on three accounts, acoustic streaming patterns, velocity vectors, and deposition trends. Two new parameters, acoustic deposition ratio and near wall vorticity magnitude, were introduced to measure and predict the correlation between variation of the acoustic fields and deposition efficiencies. It was found that the geometry that produced a high vorticity magnitude near the deposition surfaces provided the condition to induced high occurrence for aerosols depositions (up to 3.5 times the rate caused by nature deposition). The finding in this study provided a method to quantify acoustic streaming fields, and the correlation between such quantity and the related deposition performance. This provides a guideline for designing acoustic aerosol manipulation devices, which aims to cause deposit with a noninvasive method.

Copyright © 2016 American Association for Aerosol Research     

Effect of convergence angle on impactor performance

Two nozzles, modified and original, were tested in a sampler that was placed in a wind tunnel and penetration efficiencies, √Stk50, and slope of the performance curve were determined by challenging the sampler with fluorescent-tagged monodisperse test aerosol particles having known concentration. It was shown that a change in convergence angle of the modified nozzle can affect impactor performance. The √Stk50 for original and modified nozzles were 0.57 and 0.49, respectively. The slope of the efficiency curve for original and modified nozzles was 1.52 and 1.36, respectively.

© 2017 American Association for Aerosol Research     

Methodology to quantify the ratio of multiple-to single-charged fractions acquired in aerosol neutralizers

A methodology for the quantification of the ratio of multiple- to single-charged fractions acquired in aerosol neutralizers is presented. These quantities are necessary for an accurate monodisperse calibration of aerosol instrumentation. A tandem Differential Mobility Analyzer (DMA) setup is required, with the second DMA scanning the electrical mobility spectra classified in the first DMA. In contrast to previous studies on the quantification of bipolar charge distribution utilizing tandem DMA schemes, the methodology targets at the direct determination of the multiple- to single-charge fractions and does so through the analysis of the raw signal instead of the inverted size distributions, thus circumventing errors associated with the assumptions in the DMA data inversion. The proposed methodology is employed for the characterization of different types of aerosols commonly employed for instrument calibration. Spherical liquid particles (emery oil and dioctyl sebacate) were found to acquire lower multiple charge fractions than those suggested by the commonly employed regression fits of Wiedensohler, which was published in the year 1988 in the Journal of Aerosol Science (vol. 19, pp. 387–389), but still within the range of values reported in the literature. Diffusion flame soot and spark generated graphite particles, produced by a miniCAST 6203C burner and a PALAS DNP 3000, respectively, exhibited higher fraction of multiple charges, in good agreement with previous work on agglomerates. The use of a soft X-ray bipolar charger (TSI 3088) yielded systematically higher multiple fractions of positive charges compared to a ⁸⁵Kr neutralizer (TSI 3077A), confirming the importance of direct photoionization charging on the former.

Copyright © 2016 American Association for Aerosol Research     

Using silver as a surrogate for plutonium: An experimental study of the explosive silver aerosol source term

An experimental method is developed for the purpose of simulating plutonium aerosol source terms with conventional metals in laboratory. In this method, metal samples are aerosolized by high explosive detonation in a containment vessel. Aerosols having aerodynamic diameter (AD) less than 10 µm are then collected by a cascade impactor and analyzed by atomic absorption spectroscopy. Two sets of experiments were conducted. In the first set, five candidate metal samples (Ag, W, Sn, Ce, and V) were tested. It is found that the cumulative mass distribution of silver under certain conditions was in good agreement with that of plutonium from the Operation Roller Coaster-Double Track experiment. Thus, silver is chosen as a surrogate to simulate the plutonium aerosol source term. In the second set, silver aerosol source term was studied in detail with different test configurations. The results demonstrate that the peak of the mass-size distribution of silver is in the AD range 1.1–3.3 µm. The amount and fraction of relatively small silver aerosols decrease significantly with time due to coagulation and deposition. Interestingly, the amount of silver in aerosols could be expressed as a quadratic function of the peak detonation pressure.

© 2016 American Association for Aerosol Research     

Unique DNA-barcoded aerosol test particles for studying aerosol transport

Data are presented for the first use of novel DNA-barcoded aerosol test particles that have been developed to track the fate of airborne contaminants in populated environments. Until DNATrax (DNA Tagged Reagents for Aerosol eXperiments) particles were developed, there was no way to rapidly validate air transport models with realistic particles in the respirable range of 1–10 μm in diameter. The DNATrax particles, developed at Lawrence Livermore National Laboratory (LLNL) and tested with the assistance of the Pentagon Force Protection Agency, are the first safe and effective materials for aerosol transport studies that are identified by DNA molecules. The use of unique synthetic DNA barcodes overcomes the challenges of discerning the test material from pre-existing environmental or background contaminants (either naturally occurring or previously released). The DNATrax particle properties are demonstrated to have appropriate size range (approximately 1–4.5 μm in diameter) to accurately simulate bacterial spore transport. Here, we describe details of the first field test of the DNATrax aerosol test particles in a large indoor facility.

Copyright © 2016 American Association for Aerosol Research     

Numerical simulation of parallel-plate particle separator for estimation of charge distribution of PM2.5

A numerical simulation of an instrument that is used to measure the charging state of PM2.5 is conducted in order to clarify its measurement uncertainty and to improve its performance. The instrument, a parallel-plate particle separator (PPPS), is designed to classify aerosol particles according to their charging states and measure their quantities. The trajectories of submicron particles in the PPPS are numerically analyzed using the Lagrangian particle tracking method, taking into account the Brownian force and the electrostatic force. First, it is confirmed that the deterioration in the classification accuracy observed in the experiment is due to Brownian diffusion. The optimal condition that improves the accuracy is investigated through a parametric study by varying the balance of flow rates at the inlets, the geometry of the inlet and exit sections, and the applied voltage. It is found that decreasing the flow rate of the central inlet for aerosol or narrowing the central inlet improves the accuracy. The dependence of the accuracy on the flow rate is found to be in accordance with the experimental results. For charged particles, an optimum voltage that maximizes the classification accuracy is found. On the basis of the simulation results, we propose a method to determine the charge distribution of aerosol from the number of particles counted at each exit of the PPPS. In the test assuming aerosol in the air, the charge distribution determined from the number count at the exits is found to perfectly agree with the charge distribution specified at the inlet.

Copyright © 2019 American Association for Aerosol Research     

Evaluation of the new capture vaporizer for aerosol mass spectrometers: Characterization of organic aerosol mass spectra

The Aerosol Mass Spectrometer (AMS) and Aerosol Chemical Speciation Monitor (ACSM) are widely used for quantifying submicron aerosol mass concentration and composition, in particular for organic aerosols (OA). Using the standard vaporizer (SV) installed in almost all commercial instruments, a collection efficiency (CE) correction, varying with aerosol phase and chemical composition, is needed to account for particle bounce losses. Recently, a new “capture vaporizer” (CV) has been shown to achieve CE～1 for ambient aerosols, but its chemical detection properties show some differences from the SV due to the increased residence time of particles and vaporized molecules inside the CV. This study reports on the properties and changes of mass spectra of OA in CV-AMS using both AMS and ACSM for the first time. Compared with SV spectra, larger molecular-weight fragments tend to shift toward smaller ions in the CV due to additional thermal decomposition arising from increased residence time and hot surface collisions. Artifact CO⁺ ions (and to a lesser extent, H₂O⁺), when sampling long chain alkane/alkene-like OA (e.g., squalene) in the CV during the laboratory studies, are observed, probably caused by chemical reactions between sampled OA and molybdenum oxides on the vaporizer surfaces (with the carbon derived from the incident OA). No evidence for such CO⁺ enhancement is observed for ambient OA. Tracer ion marker fractions (f_m/z =, i.e., the ratio of the organic signal at a given m/z to the total OA signal), which are used to characterize the impact of different sources are still present and usable in the CV. A public, web-based spectral database for mass spectra from CV-AMS has been established.

Copyright © 2018 American Association for Aerosol Research