(Ca, V) co-doped Y2Ti2O7 yellow pigment

(Ca²⁺, V⁵⁺) co-doped Y₂Ti₂O₇ yellow pigments were prepared by solid route. The influence of the annealing temperature, the vanadium rate (0.02 ≤ x ≤ 0.3) and a post-mechanical grinding on the phase purity and the colour were studied using X-ray diffraction and UV-vis spectroscopy. The correlation between pigment colouration, synthesis parameters and structural feature is then discussed. Pigments with various colourations from yellow to deep orange can be obtained depending on the synthesis parameters linked to a slight modification of the vanadium coordination environment. For a same composition, the pigment colouration depends on the creation of Frenkel pairs inside the structure corresponding to a displacement of an oxygen atom toward one interstitial empty site.     

The photoluminescence properties of Y2O3:Eu prepared by surfactant assisted co-precipitation-molten salt synthesis

Y₂O₃:Eu³⁺ red phosphors were prepared by surfactant assisted co-precipitation-molten salt synthesis method. The effects of surfactant content and annealing temperature on the structure and luminescence were investigated by X-ray diffraction and fluorescence spectrophotometer. The use of surfactant reduces the impurities on the surface of particles and promotes the reaction. The color purity of as-prepared Y₂O₃:Eu³⁺ red phosphors is improved with the presence of surfactant. In the excitation spectra, two strong bands at 394 and 466 nm are attributed to ⁷F_0,1-⁵L₆, ⁷F_0,1-⁵D₂ transitions of Eu³⁺ ions respectively. With the excitation of 394 or 466 nm, the as-fabricated samples reveal excellent red emission as high as that of samples monitored by 254 nm. Thus, the Y₂O₃:Eu³⁺ is a promising red phosphor for ultraviolet-visible light-emitting diodes.     

Synthesis and properties of solid solutions of hexagonal YCu0.5Ti0.5O3 with YMO3 (M = Mn, Cr, Fe, Al, Ga, and In)

Solid solutions of the type Y(Cu_0.5Ti_0.5)_1−xM_xO₃ with a hexagonal structure were prepared for M = Mn, Fe, Cr, Al, Ga, and In. A complete solid solution could be obtained only in the case of M = Mn. The green color of YCu_0.5Ti_0.5O₃ was found to be enhanced by small substitutions of Al, Ga, and In. All compositions containing Mn were black in color. Suppression of magnetic transitions is observed upon co-doping of Cu/Ti into YMnO₃. Measurements of dielectric constant suggest some magneto-electric coupling may be present in the Y(Cu_0.5Ti_0.5)_1−xMn_xO₃ solid solution.     

Study on properties of CaO-SiO2-B2O3 system glass-ceramic

Low temperature co-fired ceramic (LTCC) is prepared by sintering a glass selected from CaO-SiO₂-B₂O₃ system, and its sintered bodies are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). It is found that the optimal sintering temperature for this glass-ceramic is 820 °C for 15 min, and the major phases of this material are CaSiO₃, CaB₂O₄ and SiO₂. The glass-ceramic possesses excellent dielectric properties: ?_r = 6.5, tan δ < 2 × 10⁻³ at 10 MHz, temperature coefficient of dielectric constant about −51 × 10⁻⁶ °C⁻¹ and coefficient of thermal expansion about 8 × 10⁻⁶ °C⁻¹ at 20-400 °C. Thus, this material is supposed to be suitable for the tape casting process and be compatible with Ag electrode, which could be used as the LTCC materials for the application in wireless communications.     

Temperature-dependent oxygen release, intercalation behaviour and catalytic properties of V2O5·xNb2O5 compounds

In order to investigate the catalytic properties, V_2,38Nb_10,7O_32,7, VNb₉O₂₅ and solid solutions of V₂O₅ in TT-Nb₂O₅ were prepared by thermal decomposition of freeze-dried oxalate precursors. The samples were characterised by X-ray diffraction and surface area determination. The crystalline samples are capable of the intercalation of sodium and lithium ions from solution. Above a temperature of about 500 °C, in dependence on the oxygen partial pressure a reversible release and uptake of oxygen without a structural variation takes place. The catalytic properties have been evaluated for the oxidative dehydrogenation (ODH) of propane and propene. There are only small differences in the catalytic activity of the different crystalline samples. Because of the relative high starting temperature, a selective catalytic oxidation of propane to propene is hardly observed.     

Photocatalytic properties of TiO2-P2O5 glass ceramics

Binary TiO₂-P₂O₅ glasses with 69 mol% and 76 mol% TiO₂ were prepared and converted into glass ceramics by heat-treatments. XRD measurements show that the main crystalline phases precipitated in the glass ceramics are anatase-type TiO₂ crystals or (TiO)₂P₂O₇ crystals, depending on the concentration of titanium constituent. Photocatalytic activities of the glass ceramics were evaluated by the decomposition of methylene blue (MB) and measuring the water contact angle. It is found that the glass ceramics containing anatase crystals exhibit both photocatalytic oxidation activity and highly photo-induced hydrophilicity under UV irradiation with intensity of 1.0 mW/cm².     

Structural, electrical and optical properties of TiO2-WO3 polycrystalline ceramics

Mixed oxides from the TiO₂-WO₃ system were prepared as polycrystalline materials. Their phase composition and electrical conductivity were investigated using X-ray diffraction (XRD) and dc electrical measurements. The energy gap, evaluated on the basis of optical measurements, was presented as a function of W concentration. The influence of chemical composition on structural, semiconducting and optical properties of the TiO₂-WO₃ polycrystalline ceramics was discussed.     

New substitutions and novel derivatives of the Aurivillius phases, Bi5TiNbWO15 and Bi4Ti3O12

We investigated isomorphous substitution of several metal atoms in the Aurivillius structures, Bi₅TiNbWO₁₅ and Bi₄Ti₃O₁₂, in an effort to understand structure-property correlations. Our investigations have led to the synthesis of new derivatives, Bi₄LnTiMWO₁₅ (Ln = La, Pr; M = Nb, Ta), as well as Bi₄PbNb₂WO₁₅ and Bi₃LaPbNb₂WO₁₅, that largely retain the Aurivillius (n = 1) + (n = 2) intergrowth structure of the parent oxide Bi₅TiNbWO₁₅, but characteristically tend toward a centrosymmetric/tetragonal structure for the Ln-substituted derivatives. On the other hand, coupled substitution, 2Ti^IV → M^V + Fe^III in Bi₄Ti₃O₁₂, yields new Aurivillius phases, Bi₄Ti_3−2xNb_xFe_xO₁₂ (x = 0.25, 0.50) and Bi₄Ti_3−2xTa_xFe_xO₁₂ (x = 0.25) that retain the orthorhombic noncentrosymmetric structure of the parent Bi₄Ti₃O₁₂. Two new members of this family, Bi₂Sr₂Nb₂RuO₁₂ and Bi₂SrNaNb₂RuO₁₂ that are analogous to Bi₂Sr₂Nb₂TiO₁₂, possessing tetragonal (I4/mmm) Aurivillius structure have also been synthesized.     

CO2 absorption and desorption of Bi2O3-La2O3 powders prepared by mechanical synthesis

In order to obtain CO₂-absorbents to eliminate CO₂ concentration locally, Bi₂O₃-La₂O₃ mixed powders were prepared by mechanical alloying (MA) method using a planetary ball-milling machine. CO₂-absorption and desorption properties were checked by TG-DTA for the obtained powder samples. As a result, the sample shown by (Bi₂O₃)_1−x(La₂O₃)_x [x≤0.50] was found to form α-Bi₂O₃-solid solution with repeated CO₂-adsorption and desorption around 400- 500 °C. Absorbed and desorbed CO₂ contents varied with MA time: the 72 h MA’ed sample had a larger CO₂ content than the 24 h MA’ed sample. The performance depended on the sample composition, and (Bi₂O₃)_0.70(La₂O₃)_0.30 was found to have the highest performance in the present system.     

Microwave synthesis and electrochemical characterization of mesoporous carbon@Bi2O3 composites

An efficient and quick microwave method has been employed to prepare worm-like mesoporous carbon@Bi₂O₃ composites for the first time. As-prepared products have been characterized by X-ray diffraction, N₂ adsorption-desorption, scanning electron microscopy, transmission electron microscopy and inductive coupled plasma atomic emission spectroscopy. The electrochemical measurement shows the worm-like mesoporous carbon@Bi₂O₃ composites exhibits excellent capacitance performance and the maximum specific capacitance reaches 386 F g⁻¹, three times more than the pure worm-like mesoporous carbon.     

Synthesis and upconversion luminescence properties of Yb/Er codoped BaGd2(MoO4)4 powder

Synthesis and upconversion luminescence properties of the new BaGd₂(MoO₄)₄:Yb³⁺,Er³⁺ phosphor were reported in this paper. The phosphor powder was obtained by the traditional high temperature solid-state method, and its phase structure was characterized by the XRD pattern. Based on the upconversion luminescence properties studies, it is found that, under 980 nm semiconductor laser excitation, BaGd₂(MoO₄)₄:Yb³⁺,Er³⁺ phosphor exhibits intense green upconversion luminescence, which is ascribed to ²H_11/2 → ⁴I_15/2 and ⁴S_3/2 → ⁴I_15/2 transition of Er³⁺. While the observed much weaker red emission is due to the non-radiative relaxation process of ⁴S_3/2 → ⁴F_9/2 and ⁴F_9/2 → ⁴I_15/2 transition originating from the same Er³⁺. The concentration quenching effects for both Yb³⁺ and Er³⁺ were found, and the optimum doping concentrations of 0.5 mol% Yb³⁺ and 0.08 mol% Er³⁺ in the new BaGd₂(MoO₄)₄ Gd³⁺ host were established.     

Structural properties of Al2O3-La2O3 binary oxides prepared by sol-gel

The structural properties of La₂O₃ and Al₂O₃-La₂O₃ binary oxides prepared by sol-gel were studied by XRD, HRTEM and UV-vis. The binary oxides with high lanthana contents show an amorphous structure after calcination at 650 °C. At calcination temperatures higher than 1000 °C there is a phase transformation from the amorphous state to the crystalline LaAlO₃ with a perovskite structure. The structure of La₂O₃ is consistent with the hexagonal system; however, some crystalline microdomains with a monoclinic structure were detected by HRTEM. Islands of La₂O₃ and LaAl₁₁O₁₈ phases were detected at high lanthana concentration in the binary oxide. The modification in the coordination shell of the Al³⁺ cations due to the interaction with La³⁺ cations confirms the formation of phases with a perovskite structure and the presence of islands of the LaAl₁₁O₁₈ phase.     

Complete oxidation of acetaldehyde on Pt/CeO2-ZrO2-Bi2O3 catalysts

Pt/CeO₂-ZrO₂-Bi₂O₃ catalysts for catalytic combustion of acetaldehyde, which is one of volatile organic compounds (VOCs), were prepared by a wet impregnation method in the presence of polyvinylpyrrolidone K25 (PVP). The addition of PVP in the preparation process was effective to enhance the specific surface area and the Pt²⁺ ratio on the surface. Additionally, the pore volume and size of the catalysts were modified by the PVP addition. The Pt/CeO₂-ZrO₂-Bi₂O₃ catalysts are specific for the total acetaldehyde oxidation and CO and any acetaldehyde-derivative compounds were not observed as by-products. The catalytic activity of the Pt/CeO₂-ZrO₂-Bi₂O₃ catalysts was significantly promoted by the PVP addition and the total oxidation temperature decreased. By the optimization of the amount of platinum, the complete oxidation of acetaldehyde was realized at a temperature as low as 140 °C on a 10 wt%Pt/CeO₂-ZrO₂-Bi₂O₃ catalyst.     

Influence of Sm2O3 on the crystallization and luminescence properties of boroaluminosilicate glasses

Sm₂O₃-doped SiO₂-B₂O₃-Al₂O₃-BaO glasses were prepared by melting method in order to study the influence of Sm₂O₃ on the crystallization behavior and luminescence properties. Differential scanning calorimetry (DSC), X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy were used to characterize the rare earth glasses and the crystalline phases after heat-treatment. The course of phase separation and devitrification of the glasses were also investigated. The results show that the thermal stability of the glasses decreases with the increase of content of Sm₂O₃. The crystalline phase changed from SmAl_2.07(B₄O₁₀)O_0.6 to SmBO₃. Divalent Sm²⁺ ions were detected in the crystallization product after heat-treatment. The valence transformation from Sm³⁺ to Sm²⁺ in the crystal suggests the samarium atoms entering the barium sites. The charge carried in vacancy defect induced by the substitution led to the partial reduction process. The reduction of Sm³⁺ ions was promoted by the increasing of Sm₂O₃ content or the extending of heat-treated holding time in boroaluminosilicate glass.     

Dielectric properties of B2O3-doped (1 − x)LaAlO3-xSrTiO3 ceramic system at microwave frequency

The effects of B₂O₃ addition on the microwave dielectric properties and the microstructures of (1−x)LaAlO₃-xSrTiO₃ ceramics prepared by conventional solid-state routes have been investigated. Doping with 0.25 wt.% B₂O₃ can effectively promote the densification and the microwave dielectric properties of (1−x)LaAlO₃-xSrTiO₃ ceramics. It is found that LaAlO₃-SrTiO₃ ceramics can be sintered at 1400°C due to the liquid phase effect of a B₂O₃ addition observed by scanning electronic microscopy (SEM). The dielectric constant as well as the Q×f value decreases with increasing B₂O₃ content. At 1460°C, 0.46LaAlO₃-0.54SrTiO₃ ceramics with 0.25 wt.% B₂O₃ addition possesses a dielectric constant (ε_r) of 35, a Q×f value of 38,000 (at 7 GHz) and a temperature coefficients of resonant frequency (τ_f) of −1 ppm/°C.     

Structural characterization and photocatalytic properties of novel Bi2YVO8

Bi₂YVO₈ was prepared by solid-state reaction for the first time. The structural and photocatalytic properties of Bi₂YVO₈ were studied. The results showed that this compound has the tetragonal crystal system with space group I4/mmm. The band gap of Bi₂YVO₈ was estimated to be about 2.09 eV by plotting (αhν)² versus hν and obtaining the hν axis intercept value according to Tauc's equation. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂YVO₈ as the photocatalyst under ultraviolet light irradiation (wavelength = 390 nm). Degradation of aqueous methylene blue photocatalyzed by this compound was investigated under visible light irradiation. Bi₂YVO₈ showed higher photocatalytic activity compared to Bi₂YTaO₇, Bi₂InTaO₇ or TiO₂ (P-25). Complete removal of aqueous methylene blue was achieved after visible light irradiation for 170 min. The decrease of the total organic carbon and the formation of inorganic products such as SO₄²⁻ and NO₃⁻ revealed the continuous mineralization of aqueous methylene blue during photocatalytic reaction.     

Alanine-assisted low-temperature combustion synthesis of nanocrystalline LiMn2O4 for lithium-ion batteries

Nanocrystalline LiMn₂O₄ powders have been synthesized by combustion process in a single step using a novel fuel, l-alanine. Thermogravimetric analysis and differential thermal analysis of the gel indicate a sharp combustion at a temperature as low as 149 °C. Quantitative phase analysis of X-ray diffraction data shows about 97% of phase purity in the as-synthesized powder, which on further calcination at 700 °C becomes single phase LiMn₂O₄. High Brunauer, Emmett, and Teller surface area values obtained for ash (53 m²/g) and calcined powder (23 m²/g) indicate the ultrafine nature of the powder. Average crystallite size is found to be ∼60-70 nm from X-ray diffraction analysis and transmission electron microscopy. Fourier transformed infra-red spectrum shows two strong bands at 615 and 511 cm⁻¹ originating from asymmetrical stretching of MnO₆ octahedra. A nominal composition of Li_0.88 Mn₂O₄ is calculated from the inductive coupled plasma analysis. From UV-vis spectroscopy, an optical band gap of 1.43 eV is estimated which is assigned to a transition between t_2g and e_g bands of Mn 3d. Electrochemical charge-discharge profiles show typical LiMn₂O₄ behavior with a specific capacity of 76 mAh/g.     

Room temperature synthesis of In2S3 micro- and nanorod textured thin films

Thin films of indium sulfide (In₂S₃) micro- and nanorods were successfully prepared by sulfurization of electrodeposited metal indium layers. The films were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and UV-vis spectroscopy. From XRD and TEM observations it was concluded that the In₂S₃ nanorods and microrods have ∼50 nm and ∼0.5 μm diameter, respectively. A plausible top-growth mechanism was proposed for the formation of the nanorods in which the hydroxide layer was found to play an important role. The micro- and nanorods showed optical bandgap of ∼2.2 and ∼2.54 eV, respectively. This facile and cost effective method may be extended to fabricate other metal chalcogenide nanostructures on solid substrates.     

Hydrothermal synthesis and luminescent properties of Y2O3:Tb and Gd2O3:Tb microrods

One-dimensional (1D) Y₂O₃:Tb³⁺ and Gd₂O₃:Tb³⁺ microrods have been successfully prepared through a large-scale and facile hydrothermal method followed by a subsequent calcination process in N₂/H₂ mixed atmosphere. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (IR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectra (EDX), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), photoluminescence (PL) and cathodoluminescence (CL) spectra as well as kinetic decays were used to characterize the samples. The as-formed products via the hydrothermal process could transform to cubic Y₂O₃:Tb³⁺ and Gd₂O₃:Tb³⁺ with the same morphology and slight shrinking in size after a postannealing process. Both Y₂O₃:Tb³⁺ and Gd₂O₃:Tb³⁺ microrods exhibit strong green emission corresponding to ⁵D₄ → ⁷F₅ transition (542 nm) of Tb³⁺ under UV light excitation (307 and 258 nm, respectively), and low-voltage electron beam excitation (1.5 → 3.5 kV), which have potential applications in fluorescent lamps and field emission displays.     

Synthesis and microwave dielectric properties of Sr3Zn1−xMgxNb2O9 phases

Oxides of the type, Sr₃Zn_1−xMg_xNb₂O₉ (0≤x≤1) have been obtained by the ceramic method. These oxides crystallize in the hexagonal cell corresponding to ordered triple perovskites. Sintered disks show nearly frequency-independent dielectric constant for all the compositions. Compositions sintered at 1425°C yield dielectric constant of 20-22 at ∼6 GHz, with quality factor ranging from 1300 to 1500. Sr₃Zn_0.5Mg_0.5Nb₂O₉ shows a very low temperature coefficient of resonant frequency (τ_f) of +4 ppm/°C.