Structural and optical properties of rock-salt Cd1 − xZnxO thin films prepared by thermal decomposition of electrodeposited Cd1 − xZnxO2

Cd_1 − xZn_xO nanocrystalline thin films with rock-salt structure were obtained through thermal decomposition of Cd_1 − xZn_xO₂ (x = 0, 0.37, 0.57, 1) thin films which were electrodeposited from aqueous solution at room temperature. X-ray diffraction results showed that the Zn ions were incorporated into rock salt-structure of CdO and the crystal lattice parameters decreased with the increase of Zn contents. The bandgaps of the Cd_1 − xZn_xO thin films were obtained from optical transmission and were 2.40, 2.51, 2.63 and 3.25 eV, respectively.     

Band alignment of Cd(1 − x)ZnxS produced by spray pyrolysis method

Cd_(1 − x)Zn_xS thin films have been grown on glass substrates by the spray pyrolysis method using CdCl₂ (0.05 M), ZnCl₂ (0.05 M) and H₂NCSNH₂ (0.05 M) solutions and a substrate temperature of 260 °C. The energy band gap, which depends on the mole fraction × in the spray solution used for preparing the Cd_(1 − x)Zn_xS thin films, was determined. The energy band gaps of CdS and ZnS were determined from absorbance measurements in the visible range as 2.445 eV and 3.75 eV, respectively, using Tauc theory. On the other hand, the values calculated using Elliott-Toyozawa theory were 2.486 eV and 3.87 eV, respectively. The exciton binding energies of Cd_0.8Zn_0.2S and ZnS determined using Elliott-Toyozawa theory were 38 meV and 40 meV, respectively. X-ray diffraction results showed that the Cd_(1 − x)Zn_xS thin films formed were polycrystalline with hexagonal grain structure. Atomic force microscopy studies showed that the surface roughness of the Cd_(1 − x)Zn_xS thin films was about 50 nm. Grain sizes of the Cd_(1 − x)Zn_xS thin films varied between 100 and 760 nm.     

ZnxCd1 − xS as a heterojunction partner for CuIn1 − xGaxS2 thin film solar cells

Zinc cadmium sulfide (Zn_xCd_1 − xS) heterojunction partner layer prepared with chemical bath deposition (CBD) has exhibited better blue photon response and higher current densities due to its higher bandgap than that of conventional cadmium sulfide (CdS) layer for CuIn_1 − xGa_xS₂ (CIGS2) solar cells. CIGS2/Zn_xCd_1 − xS devices have also shown higher open circuit voltage, V_oc indicating improved junction properties. A conduction band offset has been observed by J-V curves at various temperatures indicating that still higher V_oc can be obtained by optimizing the conduction band offset. This contribution discusses the effect of variation of parameters such as concentration of compounds, pH of solution and deposition time during CBD on device properties and composition and crystallinity of film. Efficiencies comparable to CIGS2/CdS devices have been achieved for CIGS2/Zn_xCd_1 − xS devices.     

Mg-composition induced effects on the physical behavior of sprayed Zn1−xMgxO films

Thin films of Zn_1 − xMg_xO, with Mg compositions in the range, 0 < x < 0.4, have been deposited onto soda-lime glass substrates using chemical spray pyrolysis. The effects of altering the alloy composition on the chemical and physical properties of the layers were investigated using X-ray photoelectron spectroscopy, atomic force microscopy, Raman, optical and electrical measurements. The data shows systematic shifts in the properties of the layers with Mg-content. In particular, the optical absorption data showed that the influence of Mg-content on the energy gap of Zn_1 − xMg_xO films is significant. Layers with x = 0.24 had an optical energy band gap, E_g = 3.87 eV. The best layers produced had properties appropriate for application as Cd-free buffer layers in copper indium gallium selenide (CIGS) solar cells.     

CuIn1 − xGaxSe2 photovoltaic devices for tandem solar cell application

CuIn_1 − xGa_xSe₂ (CIGS) solar cells show a good spectral response in a wide range of the solar spectrum and the bandgap of CIGS can be adjusted from 1.0 eV to 1.7 eV by increasing the gallium-to-indium ratio of the absorber. While the bandgaps of Ga-rich CIGS or CGS devices make them suitable for top or intermediate cells, the In rich CIGS or CIS devices are well suited to be used as bottom cells in tandem solar cells. The photocurrent can be adapted to the desired value for current matching in tandem cells by changing the composition of CIGS which influences the absorption characteristics. Therefore, CIGS layers with different [Ga]/[In + Ga] ratios were grown on Mo and ZnO:Al coated glass substrates. The grain size, composition of the layers, and morphology strongly depend on the Ga content. Layers with Ga rich composition exhibit smaller grain size and poor photovoltaic performance. The current densities of CIGS solar cells on ZnO:Al/glass varied from 29 mA cm^− 2 to 13 mA cm^− 2 depending on the Ga content, and 13.5% efficient cells were achieved using a low temperature process (450 °C). However, Ga-rich solar cells exhibit lower transmission than dye sensitized solar cells (DSC). Prospects of tandem solar cells combining a DSC with CIGS are presented.     

Synthesis of Zn1 − xCdxO bramble-like nanostructures

Ternary Zn_1 − xCd_xO bramble-like nanostructures with a Cd incorporation of about 6.7 at.% were produced onto Au-catalyzed Si substrate by thermal evaporation of Zn and Cd. The X-ray diffraction (XRD) analysis showed that the existence of lattice expansion in the c-axis orientation. The ultra-violet (UV) near-band-edge (NBE) emission of the Zn_1 − xCd_xO nanobrambles was red-shifted from 369 nm (3.37 eV) to 397 nm (3.13 eV) due to Cd substitution. The oxygen partial pressure was deemed as the critical experimental parameter for the formation of the bramble-like Zn_1 − xCd_xO nanostructures.     

Optical properties of CdxZn(1−x)O films deposited by ultrasonic spray pyrolysis method

Cd_xZn_(1−x)O (x = 0, 0.59, 0.78 and 1) films have been produced by ultrasonic spray pyrolysis technique using aqueous solutions of CdCl₂ H₂O and ZnCl₂ on the microscope glass substrate between 325 and 400 °C. The Cd_xZn_(1−x)O samples have been crystallized both cubic and hexagonal structures. The optical properties of the samples were characterized by transmittance and absorption spectroscopy measurements. Transmissions of the samples have decreased with increasing x values. The optical band gap energies of the Cd_xZn_(1−x)O samples from the absorption spectra have been calculated between 2.48 and 3.23 eV by different Zn contents. The samples were annealed at 350 and 450 °C. The optical band gap energy has decreased at 350 °C whereas it increased at 450 °C.     

Structural, electrical and optical properties of transparent Zn1 − xMgxO nanocomposite thin films

Zn_1 − xMg_xO thin films of various Mg compositions were deposited on quartz substrates using inexpensive ultrasonic spray pyrolysis technique. The influence of varying Mg composition and substrate temperature on structural, electrical and optical properties of Zn_1 − xMg_xO films were systematically investigated. The structural transition from hexagonal to cubic phase has been observed for Mg content greater than 70 mol%. AFM images of the Zn_1 − xMg_xO films (x = 0.3) deposited at optimized substrate temperature clearly reveals the formation of nanorods of hexagonal Zn_1 − xMg_xO. The variation of the cation-anion bond length to Mg content shows that the lattice constant of the hexagonal Zn_1 − xMg_xO decreases with corresponding increase in Mg content, which result in structure gradually deviating from wurtzite structure. The tuning of the band gap was obtained from 3.58 to 6.16 eV with corresponding increase in Mg content. The photoluminescence results also revealed the shift in ultraviolet peak position towards the higher energy side.     

Characterization of Zn1 − xMgxO transparent conducting thin films fabricated by multi-cathode RF-magnetron sputtering

Transparent conducting thin films of Al-doped and Ga-doped Zn_1 − xMg_xO with arbitrary Mg content x were deposited on glass substrates by simultaneous RF-magnetron sputtering of doped ZnO and MgO targets, and their fundamental properties were characterized. MgO phase separation in Zn_1 − xMg_xO films was not detected by X-ray diffraction. The Zn_1 − xMg_xO films show high optical transparency in the visible region. Although the carrier density of the Zn_1 − xMg_xO films decreased with increasing x, the Zn_1 − xMg_xO films showed good electrical conductivity; electrical resistivity as low as 8 × 10^− 4 Ω ·cm was achieved for the Zn_0.9Mg_0.1O:Ga thin film.     

Ethanol-thermal synthesis of Cd1−xZnxS nanoparticles with enhanced photodegradation of 4-chlorophenol

Cd_1−xZn_xS nanoparticles were prepared by a one-pot solvothermal process from Zn(CH₃COO)₂, Cd(CH₃COO)₂ and NaS₂CNEt₂·3H₂O (sodium diethyldithiocarbamate, DDTC). The Cd_1−xZn_xS nanoparticles were characterized by X-ray powder diffraction, transmission electron microscope and high-resolution transmission electron microscope equipped with an energy-dispersive X-ray spectrometer. The absorption spectra of the Cd_1−xZn_xS nanoparticles can be tuned into visible region by modulating stoichiometric ratio between Zn and Cd. With the increase of Zn content, the Cd_1−xZn_xS nanoparticles showed an enhanced photocatalytic activity on degradation of 4-chlorophenol. The Cd_1−xZn_xS prepared under the optimal experimental condition (initial Zn/Cd = 3:1, 210 °C, 24 h, in ethanol) possessed the best photocatalytic activity. The conversion ratio could reach up to 84% after 12 h under irradiation of visible light for Cd_1−xZn_xS prepared in ethanol, which was obviously superior to those of products prepared in water. These results showed that both crystallinity and synthetic medium were responsible for the enhanced photocatalytic activity for 4-chlorophenol.     

The properties of transparent semiconductor Zn1 − xTixO thin films prepared by the sol-gel method

Transparent semiconductor thin films of Zn_1 − xTi_xO (0 ≦ x ≦ 0.12) were deposited on alkali-free glass substrates by the sol-gel method. The effects of Ti addition on the crystallization, microstructure, optical properties and resistivity of ZnO thin films were investigated. The as-coated films were preheated at 300 °C, and then annealed at 500 °C in air ambiance. X-ray diffraction results showed all polycrystalline Zn_1 − xTi_xO thin films with preferred orientation along the (002) plane. Ti incorporated within the ZnO thin films not only decreased surface roughness but also increased optical transmittance and electrical resistivity. In the present study, the Zn_0.88Ti_0.12O film exhibited the best properties, namely an average transmittance of 91.0% (an increase of ~ 12% over the pure ZnO film) and an RMS roughness value of 1.04 nm.     

Determination of optical constants of Cd1−xZnxTe thin films by spectroscopic ellipsometry

The optical response of vacuum-evaporated Cd_1−xZn_xTe thin films in the 1.5-5.6 eV photon energy range at room temperature has been studied by spectroscopic ellipsometry. The films of Cd_1−xZn_xTe (x=0.04) were deposited at room temperature onto well-cleaned glass substrates of film thickness 450 nm. The measured dielectric-function spectra reveal distinct structures at energies of the E₁, E₁+Δ₁ and E₂ critical points corresponding to the interband transitions. Dielectric related optical constants such as complex refractive index, the absorption coefficients and the normal incidence reflectivity, are presented. Results are in satisfactory agreement with the calculations over the entire range of the photon energies.     

High-frequency magneto-electrical properties of Zn1 − x − yAlxCoyO thin films

The Al doping effects on high-frequency magneto-electric properties of Zn_{1 − x − y}Al_xCo_yO (x = 0-10.65 at.%) thin films were systematically studied. In the current work, the Zn_{1 − x − y}Al_xCo_yO thin films were deposited by magnetron co-sputtering onto quartz substrates. The magneto-impedance spectra of the thin films were measured by an impedance analyzer. Among all the doped films studied, the thin film with 6.03 at.% Al-doping showed the highest ac conductivity and relaxation frequency. To characterize the relaxation mechanism underlying the magneto-electric properties, a Cole-Cole impedance model was applied to analyze the impedance spectra. The analyzed result showed that the magneto-impedance of the Zn_{1 − x − y}Al_xCo_yO is contributed by multiple processes of magnetization dynamics and dielectric relaxation. The results imply that Zn_{1 − x − y}Al_xCo_yO may be applicable for high-frequency magneto-electric devices.     

Influence of laser-irradiation on the optical constants Se75S25 − xCdx thin films

Amorphous thin films of glassy alloys of Se₇₅S_25 − xCd_x (x = 2, 4 and 6) were prepared by thermal evaporation onto chemically cleaned glass substrates. Optical absorption and reflection measurements were carried out on as-deposited and laser-irradiated thin films in the wavelength region of 500-1000 nm. Analysis of the optical absorption data shows that the rule of no-direct transitions predominates. The laser-irradiated Se₇₅S_25 − xCd_x films showed an increase in the optical band gap and absorption coefficient with increasing the time of laser-irradiation. The results are interpreted in terms of the change in concentration of localized states due to the shift in Fermi level. The value of refractive index increases decreases with increasing photon energy and also by increasing the time of laser-irradiation. With the large absorption coefficient and change in the optical band gap and refractive index by the influence of laser-irradiation, these materials may be suitable for optical disc application.     

Structure and optical properties of AlxZn1−xO alloys by sol-gel technique

Al_xZn_1−xO (x = 0-0.5) thin films were prepared on quartz glass substrates by sol-gel technique. X-ray diffraction (XRD), scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS) were employed for microstructure characterization of these thin films. In films with up to 20 at.% Al incorporation, compound nano-crystal phase was observed while wurtzite structure disappeared. Zn3d electron binding energy and Zn LMM‘s chemical shift were both increased by more than 0.4 eV. Transmittance spectra revealed that these films possessed high transmittance in the visible region, and the end of UV absorption edge shifted to less than 300 nm when Al content exceeds 20 at.% due to quantum confinement effect.     

Cd1−xMnxTe thin films deposited by close-spaced sublimation for application in solar cells

High-quality Cd_1−xMn_xTe polycrystalline films with (1 1 1) preferred orientation were deposited by close-spaced sublimation (CSS) method. The XRD and optical absorption analysis indicated that the band gap of the film was about 1.6 eV. The as-grown Cd_1−xMn_xTe films exhibit quite low photovoltaic performance when used to make cells with CdS as the hetero-junction partner. The effect of various post-deposition treatments with vapors of chlorine-containing materials (CdCl₂ and/or MnCl₂), in Ar or H₂/Ar ambient, on the properties of Cd_1−xMn_xTe cells was studied.     

ZnO and Zn1−xCdxO nanocrystallites obtained by oxidation of precursor Langmuir-Blodgett multilayers

ZnO and Zn_1−xCd_xO nanocrystallites were prepared by oxidation of zinc arachidate-arachidic acid and zinc arachidate-cadmium arachidate-arachidic acid LB multilayers, respectively. The metal content of the multilayers was controlled by manipulation of subphase composition and pH. Precursor multilayers were oxidized in the temperature range of 400 °C-700 °C. The formation of ZnO and Zn_1−xCd_xO was confirmed by UV-Visible spectroscopy. Uniformly distributed, isolated and nearly mono-dispersed nanocrystallites of ZnO (11 ± 3 nm) and Zn_1−xCd_xO (18 ± 6 nm) were obtained.     

Initial study on the structure and optical properties of Zn1−xFexO films

Zn_1−xFe_xO (x = 0, 0.052, 0.103, 0.157 and 0.212) films were prepared by the radio-frequency magnetron sputtering technique on Si (111) substrates and the microstructure of which was characterized by X-ray diffraction, X-ray photoelectron spectroscopy, and scanning electron microscopy. The samples had a preferential c-axis orientation and the position of (002) diffraction peak shifted to the lower degree side with increasing Fe component. In order to investigate the optical transmittance properties of Zn_1−xFe_xO films, we prepared the films on Al₂O₃ (001) substrates simultaneity and the UV-VIS optical transmittance spectra showed that the band gap energy of Zn_1−xFe_xO films decreased with increase of Fe concentration. Photoluminescence spectra of the samples were observed at room temperature.     

In air synthesis of hexagonal Cd1 − xZnxS nanoparticles from single-source molecular precursors

Ternary II-VI semiconductors have many excellent physical and chemical properties, and can be used in multiple technical fields. But their previous solid state synthesis methods usually need high reaction temperatures and rigorous conditions (e.g., in vacuum or under the protection of inert gases). In this letter, we report a novel solid state synthesis of hexagonal Cd_1 − xZn_xS (x = 0-1) nanoparticles in air from a class of solid air-stable single-source molecular precursors (cadmium zinc bis(N,N-diethyldithiocarbamate, Cd_1 − xZn_x-(DDTC)₂) by two facile steps: firstly, Cd_1 − xZn_x-(DDTC)₂ (x = 0-1) were prepared directly through the precipitation reactions of stoichiometric cadmium sulfate, zinc acetate and sodium diethyldithiocarbamate in distilled water under the ambient condition (8 °C, 1 atmospheric pressure); secondly, hexagonal Cd_1 − xZn_xS (x = 0-1) nanoparticles were produced simply via thermolysis of the single-source precursors in air at 300 °C for 3 h. The proposed method may serve as a kind of simple, mild and cheap way to synthesize nanomaterials of many ternary metal sulfide semiconductors, which have promising applications in the photocatalysis and optoelectronic devices.     

Pulsed-laser deposition of heteroepitaxial corundum-type ZITO: cor-In2 − 2xZnxSnxO3

Thin films of corundum-type In_2 − 2xZn_xSn_xO₃ (cor-ZITO) were grown on lattice-matched substrates using pulsed laser deposition. The (001) of the corundum-type film grew heteroepitaxial to the (001) of a LiNbO₃ substrate with large grains along the in-plane and out-of-plane orientation characterized by glancing incidence X-ray diffraction and four-circle Φ-scans. A film with 34% In (metals basis) exhibited a wide optical gap of 3.9 eV and a modest conductivity of 134 S/cm, which suggests cor-ZITO is a potential low-cost transparent conducting oxide.